Chemical and electrochemical synthesis of conducting graft copolymer of acrylonitrile with aniline

A new conducting copolymer, polyacrylonitrile‐graft‐polyaniline (PAN‐g‐PANi), has been prepared by chemical and electrochemical methods from a precursor polymer. Poly[acrylonitrile‐co‐(acrylimine phenylenediamine)] (PAN‐co‐PAIPD) was synthesized chemically by reacting PAN with sodium 1,4‐phenylenediamine salt. PAN‐g‐PANi was synthesized chemically using ammonium peroxydisulfate as the oxidant and p‐toluenesulfonic acid in dimethylsulfoxide solution and adding aniline to oxidized PAN‐co‐PAIPD. Electrochemical polymerization was carried out by spin coating PAN‐co‐PAIPD on the surface of a Pt electrode, then the growth of the graft copolymer (PAN‐g‐PANi) in the presence of fresh aniline and acidic solution. The structures of the graft copolymer and PAN‐co‐PAIPD were characterized using UV‐visible, Fourier transform infrared, and ¹H and ¹³C NMR spectroscopies. The thermal properties of PAN‐g‐PANi were studied using thermogravimetric analysis and differential scanning calorimetry. Scanning electron microscopy (SEM) images showed that the morphology of PAN‐g‐PANi copolymer films was homogeneous. Electrical conductivity of the copolymer was studied using the four‐probe method, which gave a conductivity of 4.5 × 10^?3 S cm^?1 with 51.4% PANi. SEM and electrical conductivity measurements supported the formation of the graft copolymer. Copyright © 2006 Society of Chemical Industry     

Preparation of PAA‐g‐PEG/PANI polymer gel electrolyte and its application in quasi solid state dye‐sensitized solar cells

A microporous hybrid polymer of poly(acrylic acid)‐g‐poly(ethylene glycol)/polyaniline (PAA‐g‐PEG/PANI) is synthesized by a two‐step solution polymerization method. The influence of aniline concentration on the conductivity of PAA‐g‐PEG/PANI gel electrolyte is discussed, when the concentration of aniline is 0.66 wt%, the conductivity of PAA‐g‐PEG/PANI gel electrolyte is 11.50 mS cm^?1. Using this gel electrolyte as host, a quasi solid state dye‐sensitized solar cell (QS‐DSSC) is assembled. The QS‐DSSC based on this gel electrolyte achieves a power conversion efficiency of 6.38% under a simulated solar illumination of 100 mW cm^?2 (AM 1.5). POLYM. ENG. SCI., 55:322–326, 2015. © 2014 Society of Plastics Engineers     

Preparation and ionic conductivity of solid polymer electrolyte based on polyacrylonitrile‐polyethylene oxide

The transparent and flexible solid polymer electrolytes (SPEs) were fabricated from polyacrylonitrile‐polyethylene oxide (PAN‐PEO) copolymer which was synthesized by methacrylate‐headed PEO macromonomer and acrylonitrile. The formation of copolymer is confirmed by Fourier‐transform infrared spectroscopy (FTIR) measurements. The ionic conductivity was measured by alternating current (AC) impedance spectroscopy. Ionic conductivity of PAN‐PEO‐LiClO₄ complexes was investigated with various salt concentration, temperatures and molecular weight of PEO (Mn). And the maximum ionic conductivity at room temperature was measured to be 3.54 × 10^?4 S/cm with an [Li⁺]/[EO] mole ratio of about 0.1. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 461–464, 2006     

Enhancement of dielectric and energy density properties in the PVDF‐based copolymer/terpolymer blends

We investigated the high dielectric constant and energy storage density for the blends of P(VDF‐TrFE) copolymer and P(VDF‐TrFE‐CFE) terpolymer. The degradation of coercive field (E_c) and remnant polarization (P_r) of the copolymer under an electric field of 125 MV/m was observed and the copolymer changed into a typical relaxor ferroelectric with doping of terpolymer. The dielectric constant of P(VDF‐TrFE) was found to be ～11, but was enhanced to ～55 by blending with P(VDF‐TrFE‐CFE) at 60 wt%. Consequently, a higher energy density of about 4.2 J/cm³ was obtained in these blends in contrast to about 3.6 J/cm³ in the terpolymer at the very low applied electric field of 125 MV/m. These results demonstrate the promise of blend approaches for tailoring and enhancing the dielectric properties of ferroelectric polymers. POLYM. ENG. SCI., 55:1396–1402, 2015. © 2015 Society of Plastics Engineers     

In situ cyclization reactions during the preparation of high‐performance methacrylic acid/acrylonitrile/acrylamide ternary copolymer foam

A new high‐performance methacrylic acid/acrylonitrile/acrylamide ternary copolymer foam was prepared by radical bulk copolymerization, and the reaction mechanism of in situ cyclization taking place during copolymer foaming as well as the heat treatment was examined too. Then, the crucial mechanism was validated via optical microscopy, infrared absorption spectroscopy (Fourier transform infrared), differential thermal analysis (differential scanning calorimetry), and thermogravimetric analysis. The results showed a weak exothermic peak at 149.17°C and a strong endothermic peak at 270.85°C in differential scanning calorimetry curves of the methacrylic acid/acrylonitrile/acrylamide copolymer after the foaming and heat treatment at 160°C for 2 h and at 200°C for 2 h. The peak temperature of the differential thermogravimetry curve was 175.87°C, whereas the weight‐loss rate was less at 276.58°C in the thermogravimetry curves. In the case of the Fourier transform infrared curves, the ? OH absorption peak at 930–970 and 1480 cm^?1 weakened, and the C? N absorption peak of the imide increased. The >C?O absorption peak at 1700 cm^?1 occurred as an excursion phenomenon toward the low‐frequency field; at the same time, the second absorption peak increased. Furthermore, the ? C?N absorption peak at 2240 cm^?1 weakened, and a new ? C?N? absorption band appeared. All these data revealed that in situ cyclizations had taken place in the copolymer molecule chains, so some rigid ring structures appeared in the copolymer molecule chains, such as six‐membered imide rings and ladder polymer structures. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterizations of hydrophobically associating water‐soluble polymer with nonionic surfmer

In this article, a hydrophobically associating copolymer (2‐acrylamido)‐2‐methylpropanesulfonic acid (AMPS)/AA‐EO₂₅C₁₂ was synthesized by AMPS and nonionic surfmer AA‐EO₂₅C₁₂ through free radical copolymerization. The structure of copolymer was characterized by FT‐IR and ¹H‐NMR. The properties of copolymer were studied and the results indicated that the copolymer exhibits good thickening ability due to intermolecular hydrophobic associations as the apparent viscosity of the copolymer solution increases sharply with increasing polymer concentration. Compared with homopolymer PAMPS, the rheological test indicates that the copolymer solution shows shear thickening behavior at low shear rate region. Besides, the copolymer exhibits interfacial activity as it can reduce the interfacial tension to 10° level, and ability to form emulsion with good stability, which is due to successfully introducing the structure of nonionic surfmer AA‐EO₂₅C₁₂ to the polymer chain. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43195.     

Rheology of polyacrylonitrile‐based precursor polymers produced from controlled (RAFT) and conventional polymerization: Its role in solution spinning

Polymer solutions in dimethyl sulfoxide (DMSO) as a solvent, made from reversible addition fragmentation chain transfer (RAFT)‐mediated polyacrylonitrile (RAFT^¥ PAN) terpolymer with molecular weight (MW) of 260,000 g/mol and dispersity (Ð) of 1.29, behave differently under applied shear stress than polymer solutions made from conventional PAN (Control PAN) with similar MW (258,000 g/mol) but Ð of 2.05 in the same solvent. The unique rheology of RAFT PAN is because of the reduced amount of high MW polymer fractions. Specifically, a 25% (w/v) polymer solution of RAFT PAN had a viscosity of 198 Pas while the equivalent control PAN polymer solution had a viscosity of 968 Pas at a shear rate of 1 s^?1. Also, RAFT PAN polymer solutions had a longer Newtonian plateau than control PAN polymer solutions. This exhibits more liquid character in RAFT PAN polymer solutions than control PAN polymer solutions at same temperature and concentration. In dynamic tests, RAFT PAN polymer solutions gelled slower than their equivalent control PAN polymer solutions because of their longer polymer chain relaxation times. Slow gelling and higher liquid character in RAFT PAN polymer solutions can result in obtaining stronger and finer precursor fibers during wet spinning. Since RAFT PAN polymer solutions exhibit low viscosity and higher liquid character when compared to its equivalent control PAN at same concentration and temperature, these can allow a wider working window for wet spinning and can also allow higher solid content in the polymer solutions that remain easy to wet spin. This is expected to lead to compact and finer fibers with less voids and higher strength. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44273.     

Preparation and characterization of amphiphilic block copolymer of polyacrylonitrile‐block‐poly(ethylene oxide)

The synthesis of polyacrylonitrile‐block‐poly(ethylene oxide) (PAN‐b‐PEO) diblock copolymers is conducted by sequential initiation and Ce(IV) redox polymerization using amino‐alcohol as the parent compound. In the first step, amino‐alcohol potassium with a protected amine group initiates the polymerization of ethylene oxide (EO) to yield poly(ethylene oxide) (PEO) with an amine end group (PEO‐NH₂), which is used to synthesize a PAN‐b‐PEO diblock copolymer with Ce(IV) that takes place in the redox initiation system. A PAN‐poly(ethylene glycol)‐PAN (PAN‐PEG‐PAN) triblock copolymer is prepared by the same redox system consisting of ceric ions and PEG in an aqueous medium. The structure of the copolymer is characterized in detail by GPC, IR, ¹H‐NMR, DSC, and X‐ray diffraction. The propagation of the PAN chain is dependent on the molecular weight and concentration of the PEO prepolymer. The crystallization of the PAN and PEO block is discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1753–1759, 2003     

Stability constants of amidoximated chitosan‐g‐poly(acrylonitrile) copolymer for heavy metal ions

Amidoximated chitosan‐g‐poly(acrylonitrile) (PAN) copolymer was prepared by a reaction between hydroxylamine and cyano group in chitosan‐g‐PAN copolymer prepared by grafting PAN onto crosslinked chitosan with epychlorohydrine. The adsorption and desorption capacities for heavy metal ions were measured under various conditions. The adsorption capacity of amidoximated chitosan‐g‐PAN copolymer increased with increasing pH values, and was increased for Cu²⁺ and Pb²⁺ but a little decreased for Zn²⁺ and Cd²⁺ with increasing PAN grafting percentage in amidoximated chitosan‐g‐PAN copolymer. In addition, desorption capacity for all metal ions was increased with increasing pH values in contrast to the adsorption results. Stability constants of amidoximated chitosan‐g‐PAN copolymer were higher for Cu²⁺ and Pb²⁺ but lower for Zn²⁺ and Cd²⁺ than those of crosslinked chitosan. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 469–476, 1999     

Amphiphilic poly(acrylonitrile‐co‐acrylic acid)/silver nanocomposite additives for the preparation of antibiofouling membranes with improved properties

This work focuses the preparation of polymer‐silver nanocomposite (Ag‐Nc) dense free standing films and nonwoven fabric supported porous ultrafiltration membranes with improved membrane performance and long‐term antibiofouling properties. New polyacrylonitrle‐based Ag‐Ncs, poly(acrylonitrle‐co‐acrylic acid)‐silver (PAN‐co‐PAA‐Ag) containing 35 wt% of PAA and 0.35–0.65 wt% of Ag‐nanoparticles (Nps) were synthesized and used as additives for the fabrication of PAN‐based (PAN/PAN‐co‐PAA‐Ag) Ag‐Nc porous membranes and dense‐free standing films. The Ag‐Nps were homogeneously dispersed into the PAN‐co‐PAA random copolymer matrix. The prepared membranes (PAN/PAN‐co‐PAA‐Ag) showed combination of properties such as excellent antimicrobial activity towards both Gram Negative and Gram Positive bacteria (prevent biofilm formation), improved protein antifouling properties, and enhanced water flux when compared to neat PAN‐based membrane. The antimicrobial properties, hydrophilicity, and the water flux of various membranes follow the following order for the membranes PAN < PAN/PAN‐co‐PAA < PAN/PAN‐co‐PAA‐Ag. Extraneous addition of small amount of polyethylene glycol (PEG) during preparation of additive i.e. [PEG + PAN‐co‐PAA]‐Ag further improved the protein antifouling properties of the PAN‐based membranes (PAN/[PEG+PAN‐co‐PAA‐Ag]). The dispersed Ag‐Nps were stable on the surface of phase inverted membranes for long period of time and PAN/PAN‐co‐PAA‐Ag membranes are therefore suitable for long‐term water treatment under bacterial environment. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

A copolymer of poly[2,2′‐(m‐phenylene)‐5,5′‐ bibenzimidazole] and poly(2,5‐benzimidazole) for high‐temperature proton‐conducting membranes

A novel copolymer of polybenzimidazoles was prepared by copolymerization of 3,3′‐diaminobenzidine tetrahydrochloride, 3,4‐diaminobenzoic acid and isophthalic acid in polyphosphoric acid at 200 °C. The polymerization could be performed within 90–110 min with the assistance of microwave irradiation. The solubility of the copolymer obtained in N,N‐dimethylacetamide (DMAc) was improved compared with those of poly[2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole] and poly(2,5‐benzimidazole). Thus copolymer membranes could be readily prepared by dissolving the copolymer powders in DMAc with refluxing under ambient pressure. The decomposition temperature of the copolymer was about 520 °C in air according to thermogravimetric analysis data. The proton conductivity and mechanical strength of the phosphoric acid‐doped copolymer membranes were investigated at elevated temperatures. A conductivity of 0.09 S cm^?1 at 180 °C and a tensile stress at break of 5.9 MPa at 120 °C were achieved for the acid‐doped copolymer membranes by doping acids in a 75 wt% H₃PO₄ solution. Copyright © 2010 Society of Chemical Industry     

Fabrication and properties of solution processed all polymer thin‐film ferroelectric device

A ferroelectric device, making use of a flexible plastic, polyethylenterephtalate (PET), as a substrate was fabricated by all solution processes. PET was globally coated by a conducting polymer, poly(3,4‐ethylenedioxythiophene) poly(styrenesulfonate) acid (PEDOT/PSSH), which is used as bottom electrode. The ferroelectric copolymer, poly(vinylidenefluoride–trifluoroethylene) (PVDF–TrFE), thin film was deposited by spin‐coating process from solution. The top electrode, polyaniline, was coated by solution process as well. The ferroelectric properties were measured on this all solution processed all polymer ferroelectric thin‐film devices. A square and symmetric hysteresis loop was observed with high‐polarization level at 15‐V drive voltage on a all polymer device with 700 Å (PVDF–TrFE) film. The relatively inexpensive conducting polyaniline electrode is functional well and therefore is a good candidate as electrode material for ferroelectric polymer thin‐film device. The remnant polarization P_r was 8.5 μC/cm² before the fatigue. The ferroelectric degradation starts after 1 × 10³ times of switching and decreases to 4.9 μC/cm² after 1 × 10⁵ times of switching. The pulse polarization test shows switching take places as fast as a few micro seconds to reach 90% of the saturated polarization. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Diffusion dynamics of ionic liquids during the coagulation of solution spinning for acrylic fibers

The coagulation dynamics of acrylic polymer (PAN) with 1‐butyl‐3‐methylimidazolium chloride [BMIM]Cl as solvent for PAN and H₂O as nonsolvent was investigated in detail. On the basis of Fick's second law of diffusion, a mass‐transfer model of [BMIM]Cl from concentrated PAN/[BMIM]Cl solution was established as verified with the experimental data. The established model has a good fit with the experimental data and the diffusion coefficient D of [BMIM]Cl was calculated according to the model. The diffusion coefficient D decreased a little when the concentration of solution increased. As increasing the coagulation bath concentration, the diffusion coefficient D initially increased and then decreased, reaching a maximum of 5 wt% in the coagulation bath. The diffusion coefficient D decreased with the coagulation bath temperature. From the diffusion coefficient and the structure of the coagulated filament, it can be concluded that the diffusion rate of [BMIM]Cl from PAN concentrate solutions is relatively slow, which is prospective to prepare uniform‐structure fibers. POLYM. ENG. SCI., 48:184–190, 2008. © 2007 Society of Plastics Engineers     

The effect of dimethylsulfoxide on the dissociation process of physical complexes of polyacrylonitrile in N,N‐dimethylformamide

The physical properties and gelation behavior of polyacrylonitrile (PAN ) solutions were investigated in mixed solvents of N ,N ‐dimethylformamide (DMF ) and dimethylsulfoxide (DMSO ). For the individual solubility parameters, DMSO had the polar term closer to PAN than DMF . Small‐angle X‐ray scattering profiles and Fourier transform infrared spectra of 20 wt% PAN solutions confirmed that the internal structure and intermolecular complexes between nitrile groups were broken up by the DMSO molecules. The slope of Cole–Cole plot, a measure of the solution heterogeneity, increased with the mole fraction of DMSO (X _DMSO) via three distinct zones. The homogenization was particularly noticeable in Zone 1 (0.0 < X _DMSO < 0.4) and Zone 3 (0.7 < X _DMSO < 1.0). The Huggins constant and UV‐visible absorption at 268 nm of dilute solutions decreased sharply above X _DMSO of 0.7 in Zone 3. This indicated a marked increase of PAN solubility by dissociating the intramolecular complexes between nitrile groups. In Zone 1, the storage modulus of 20 wt% PAN solutions decreased but loss modulus remained almost constant with X _DMSO at lower frequency below 1 rad s^?1, indicating the weakening of the true entanglement points of the intermolecular complexes. The mechanism indicated that the intermolecular complexes between nitrile groups were dissociated by DMSO earlier than the intramolecular ones. © 2017 Society of Chemical Industry     

Synthesis and characterization of copolymer of styrene with methacrylic acid initiated by triphenylbismuthonium 1,2,3,4‐ tetraphenylcyclopentadienylide

The radical copolymerization of styrene with methacrylic acid (MAA) initiated by triphenylbismuthonium 1,2,3,4‐tetraphenylcyclopentadienylide in dioxan at 80 ± 0.1 °C for 3 h results in the formation of alternating copolymer as evidenced from the values of reactivity ratios as r₁ (styrene) = 0.03 and r₂ (MAA) = 0.025. The kinetic expression is R_p α [I]^0.5 [Sty] [MAA] and overall energy of activation is computed to be 23 kJ/mol. The FTIR spectrum of the copolymer shows the presence of bands at 3054 cm^?1 assigned to the phenyl group of styrene and at 1724 cm^?1 assigned to the ? COOH group of MAA. The ¹H‐NMR spectrum of the copolymer shows peaks between 7.20 and 7.27 δ assigned to the phenyl protons of styrene and at 12.5 δ assigned to the COOH proton of MAA. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1838–1843, 2005     

Spin probe study of semi‐interpenetrating polymer networks based on polyurethane and polymethacrylate functional prepolymers

The motional transition and heterogeneity of semi‐interpenetrating networks (SIPNs) based on polyurethane (PU) with carboxylic groups and methacrylic copolymer (PM) with tertiary amine groups were studied by the electron spin resonance (ESR) spin probe method. The concentration of functional groups in both prepolymers varied from 0 to 0.45 mmol g^?1. Spin‐probed SIPNs show that the temperature‐dependent spectra are sensitive to polymer interactions imposed by functional groups. These interactions determine the free volume distribution in the matrix and temperature at which motional transition takes place. The fraction of free volume increases with functional group concentration and reaches its maximum at 0.25 mmol g^?1. Further increases in the functional group concentration reduce the free volume. The results of the networks with strong interactions are discussed in terms of the interference of the plasticizing effect of the PU component and the formation of possible cluster cross‐links, which restricts segmental motions. Copyright © 2003 Society of Chemical Industry     

Effect of propylene carbonate on the ionic conductivity of polyacrylonitrile‐based solid polymer electrolytes

Solid polymer electrolyte membranes consisting of polyacrylonitrile (PAN) as a host polymer, ammonium nitrate (NH₄NO₃) as a complexing salt, and propylene carbonate (PC) as a plasticizer were prepared by a solution casting technique. An increase in the amorphous nature of the polymer electrolytes was confirmed by X‐ray diffraction analysis. A shift in the glass‐transition temperature of the PAN/NH₄NO₃/PC electrolytes was observed in the differential scanning calorimetry thermograms; this indicated interactions between the polymer and the salt. The impedance spectroscopy technique was used to study the mode of ion conduction in the plasticized polymer electrolyte. The highest ionic conductivity was found to be 7.48 × 10^?3 S/cm at 303 K for 80 mol % PAN, 20 mol % NH₄NO₃, and 0.02 mol % PC. The activation energy of the plasticized polymer electrolyte (80 mol % PAN/20 mol % NH₄NO₃/0.02 mol % PC) was found to be 0.08 eV; this was considerably lower than that of the film without the plasticizers. The dielectric behavior of the electrolyte is discussed in this article. A literature survey indicated that the synthesis and characterization of ammonium‐salt‐doped, proton‐conducting polymer electrolytes based on PAN has been rare. The use of the best composition membrane (80 mol % PAN/20 mol % NH₄NO₃/0.02 mol % PC) proton battery was constructed and evaluated. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41743.     

Graft copolymerization of soybean protein isolate and methacrylic acid

Graft copolymers of soybean protein isolate (SPI) and methacrylic acid (MAA) were prepared in an 8 mol/L urea aqueous solution with ammonium persulfate (APS) as an initiator, β‐mercaptoethanol as an unfolding agent for SPI, and a chain‐transfer agent. Evidence of grafting was obtained by the comparison of the Fourier transform infrared and NMR spectra of SPI with those of the SPI‐grafted MAA copolymer [SPI‐g‐poly(methacrylic acid) (PMAA)]. A possible copolymerization mechanism of SPI and MAA was determined, and the copolymerization rate equation was derived. The effect of β‐mercaptoethanol content, APS content, and reaction temperature on the graft copolymerization was studied by the determination of the grafting parameters, including grafting percentage and grafting efficiency. Dynamic laser light scattering was used to investigate the effect of the pH value on the hydrodynamic radius of SPI and the grafted SPI aggregate in aqueous solution. The average hydrodynamic radius of SPI‐g‐PMAA aggregate was much smaller than that of the SPI aggregate at about the isoelectric point of SPI and a high pH value, and the hydrodynamic radius distribution of the SPI‐g‐PMAA aggregate was narrower than that of the SPI aggregate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4023–4029, 2006     

Dielectric properties of lithium‐perchlorate‐filled acrylonitrile–hexyl methacrylate copolymer films

A series of poly(acrylonitrile‐co‐hexyl methacrylate), PAN‐co‐PHMA, copolymers with various hexyl methacrylate (HMA) contents were synthesized by emulsion technique. The incorporation of HMA units into the copolymers was confirmed by Fourier transform infrared and proton nuclear magnetic resonance (¹H‐NMR) spectroscopy. Glass transition temperatures (T _g) and thermal decomposition temperatures of copolymers were determined by differential scanning calorimetry and thermogravimetric analysis. The T _g of copolymers were lowered monotonically by increasing HMA content, while thermal stabilities of copolymers were enhanced. The frequency dependence of dielectric properties of three different amounts of LiClO₄ salt doped copolymer films was investigated. The influence of molar fraction of HMA on dielectric constant and ac‐conductivity of copolymer films was examined. Samples with higher HMA contents showed better stability and conductivity, as a result of increase in free volume and the mobility of the dipoles. The ac conductivity of copolymers was also improved by increasing LiClO₄ salt which was due to the existence of more charge carriers. PAN(88)‐co‐PHMA(12) copolymer with 1.5 mol% of lithium salt exhibited ionic conductivity of the 7.8 × 10⁻⁴ S/cm at 298 K. POLYM. COMPOS., 38:1792–1799, 2017. © 2015 Society of Plastics Engineers     

Preparation and characterization of sulfonated block‐graft copolyimide/sulfonated polybenzimidazole blend membranes for fuel cell application

Polymer electrolyte blend membranes composed of sulfonated block‐graft polyimide (S‐bg‐PI) and sulfonated polybenzimidazole (sPBI) were prepared and characterized. The proton conductivity and oxygen permeability coefficient of the novel blend membrane S‐bg‐PI/sPBI (7 wt%) were 0.38 S cm^?1 at 90 °C and 98% relative humidity and 7.2 × 10^?13 cm³(STP) cm (cm² s cmHg)^?1 at 35 °C and 76 cmHg, respectively, while those of Nafion^® were 0.15 S cm^?1 and 1.1 × 10^?10 cm³(STP) cm (cm² s cmHg)^?1 under the same conditions. The apparent (proton/oxygen transport) selectivity calculated from the proton conductivity and the oxygen permeability coefficient in the S‐bg‐PI/sPBI (7 wt%) membrane was 300 times larger than that determined in the Nafion membrane. Besides, the excellent gas barrier properties based on an acid ? base interaction in the blend membranes are expected to suppress the generation of hydrogen peroxide and reactive oxygen species, which will degrade fuel cells during operation. The excellent proton conductivity and gas barrier properties of the novel membranes promise their application for future fuel cell membranes. © 2015 Society of Chemical Industry