Cationic surfactant promoted reductive electrodeposition of nanocrystalline anatase TiO2 for application to dye-sensitized solar cells

A new strategy involving the introduction of the common cationic surfactant cetyltrimethylammonium bromide (CTAB) for the cathodic deposition of titanium dioxide from hydrolyzed TiCl₄ and TiCl₃ solutions by cyclic voltammetry has been developed. Crack-free and non-transparent anatase TiO₂ films were obtained for the first time and characterized with the aid of Raman spectra and SEM. Selection of TiCl₄ as the precursor for the electrodeposition is quite a novel approach for the research in the area of dye-sensitized solar cells (DSSCs). It is noted that NO₃⁻ ion is essential for such a deposition. Under the same conditions, a thicker TiO₂ film was obtained by adding CTAB into KNO₃ electrolyte, compared with the case without it. The CTAB-promoted film led to an increased energy conversion efficiency of the corresponding DSSC. Mechanisms are proposed for the electrochemical deposition and the beneficial role of CTAB.     

Optimization of the dye-sensitized solar cell performance by mechanical compression

In this study, the P25 titanium dioxide (TiO₂) nanoparticle (NP) thin film was coated on the fluorine-doped tin oxide (FTO) glass substrate by a doctor blade method. The film then compressed mechanically to be the photoanode of dye-sensitized solar cells (DSSCs). Various compression pressures on TiO₂ NP film were tested to optimize the performance of DSSCs. The mechanical compression reduces TiO₂ inter-particle distance improving the electron transport efficiency. The UV–vis spectrophotometer and electrochemical impedance spectroscopy (EIS) were employed to quantify the light-harvesting efficiency and the charge transport impedance at various interfaces in DSSC, respectively. The incident photon-to-current conversion efficiency was also monitored. The results show that when the DSSC fabricated by the TiO₂ NP thin film compressed at pressure of 279 kg/cm², the minimum resistance of 9.38 Ω at dye/TiO₂ NP/electrolyte interfaces, the maximum short-circuit photocurrent density of 15.11 mA/cm², and the photoelectric conversion efficiency of 5.94% were observed. Compared to the DSSC fabricated by the non-compression of TiO₂ NP thin film, the overall conversion efficiency is improved over 19.5%. The study proves that under suitable compression pressure the performance of DSSC can be optimized.     

Synthesis of Zn-doped TiO2 microspheres with enhanced photovoltaic performance and application for dye-sensitized solar cells

Zn-doped TiO₂ microspheres have been synthesized by introducing a trace amount of zinc nitrate hexahydrate to the reaction system. Scanning electron microscope (SEM), field-emission scanning electron microscope (FESEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) have been utilized to characterize the samples. Both surface photovoltage spectroscopy (SPS) technique based on lock-in amplifier and transient photovoltage (TPV) measurement reveal that the slight doping of Zn can promote the separation of photo-generated charges as well as restrain the recombination due to the strong interface built-in electric field and the decreasing of surface trap states. The photovoltaic parameters of dye-sensitized solar cells (DSSCs) based on Zn-doped TiO₂ are significantly better, compared to that of a cell based on undoped TiO₂. The relation between the performance of DSSCs and their photovoltaic properties is also discussed.     

Efficiency improvement of dye-sensitized tandem solar cell by increasing the photovoltage of the back sub-cell

In tandem-structured dye-sensitized solar cell (DSSC) composed of two parallel-connected sub-cells, the photovoltage (V_oc) generated by the back sub-cell is usually rather low, resulting in low V_oc and conversion efficiency (η) of the tandem cell. To solve this issue, two simple but very efficient strategies, namely, the filling of Li⁺-absent electrolyte and/or coating Al₂O₃ on TiO₂ electrode surface in the back sub-cell, were explored to enhance the V_oc of the back sub-cell and hence that of the tandem cell. The former strategy was expected to heighten the energy level of TiO₂ conduction band, and the latter one to retard the charge recombination. The photovoltaic performance measurements reveal that in the both cases, although there was a slight decrease in the photocurrent (J_sc), an obvious rise in the V_oc was achieved for the tandem cells, leading to significant improvements in η of the tandem cells. Compared to the individual organic dye-sensitized solar cell (the highest η is 7.58%), the tandem cell with two organic dyes having complementary absorption spectra demonstrates an improved efficiency of up to 8.33% by a combinational application of Li⁺-absent electrolyte and Al₂O₃ overcoat. The results presented in this study highlight that the efficiency of a parallel-connected tandem-structured DSSC can be improved significantly through enhancing the photovoltage of the back sub-cell, which is first time reported.     

TiO2/modified natural clay semiconductor as a potential electrode for natural dye-sensitized solar cell

TiO₂/modified natural bentonite clay semiconductor, as a potential electrode of dye-sensitized solar cell, having a Ti:Si molar ratio of 85:15 was, for the first time, compared with pure TiO₂ (commercial P25) electrode in terms of solar cell efficiency and characteristics. 4-Chloro-2,5-difluorobenzoic acid and 4-(chloromethyl)benzoyl chloride were added to the electrodes to increase light harvesting ability of natural dyes extracted from red cabbage, rosella, and blue pea. The results showed that the TiO₂/clay semiconductor provided a higher surface area but a slightly lower efficiency than the pure TiO₂. The best natural sensitizer was found to be the dye extracted from red cabbage. Besides, the 4-(chloromethyl)benzoyl chloride provided a higher short circuit current for the TiO₂/clay semiconductor.     

The improvement of electron transport rate of TiO2 dye-sensitized solar cells using mixed nanostructures with different phase compositions

Dye-sensitized solar cells (DSCCs) in the form of mixed nanostructures containing TiO₂ nanoparticles and nanowires with different weight ratios and phase compositions are reported. X-ray diffraction and field emission scanning electron microscopy analyses revealed that the synthesized TiO₂ nanoparticles had average crystallite size in the range 21–39 nm, whereas TiO₂ nanowires showed diameter in the range 20–50 nm. The indirect optical band gap energy of TiO₂ nanowires, anatase- and rutile-TiO₂ nanoparticles was calculated to be 3.35, 3.28 and 3.17 eV, respectively. The power conversion efficiency of the solar cells changed with nanowire to nanoparticle weight ratio, reaching a maximum at a specific value. An increase of 4.3% in cell efficiency was achieved by introducing 10 wt% nanowire into the as-synthesized TiO₂ nanoparticles (WP1 cell). Furthermore, an increase of 27.6% in cell efficiency was achieved by using crystalline anatase-TiO₂ nanoparticles rather than as-synthesized TiO₂ nanoparticles in WP1 solar cell. It was found that the power conversion efficiency and short circuit current of WP1 cell were decreased down to around 30.8% and 39.1%, respectively using rutile nanoparticles rather than anatase nanoparticles. The improvement of cell efficiency was related to rapid electron transport and less recombination of photogenerated electrons, as confirmed by electrochemical impedance spectroscopy.     

Anatase TiO2 spheres with high surface area and mesoporous structure via a hydrothermal process for dye-sensitized solar cells

Spherical pure anatase TiO₂ spheres with a mesoporous structure and high surface area of up to 116.5 m² g⁻¹ were prepared by a simple urea-assisted hydrothermal process and investigated as dye-sensitized solar-cell electrodes. Although the particle diameters of the prepared TiO₂ spheres ranged from 0.4 to 1.3 μm, due to the high specific surface area, mesoporous TiO₂ sphere electrode was obtained with enhanced light harvesting and a larger amount of dye loading. An overall light conversion efficiency of 7.54% under illumination of simulated AM 1.5G solar light (100 mW cm⁻²) was achieved using the mesoporous TiO₂ spheres electrode, which was significantly higher than a commercial Degussa P25 TiO₂ nanocrystals electrode (5.69%).     

Efficiency improvement of dye-sensitized solar cells based on electrodeposited TiO2 films by low temperature post-treatment

Porous crystalline TiO₂ films can be prepared at low temperatures (80 °C) by surfactant-assisted electrodeposition from TiCl₃ solution. Nevertheless, up to now calcination at high temperatures (typically 450 °C) was still necessary to establish a good performance of these films in dye-sensitized solar cells (DSSC). With this study we report that water vapour treatment at much lower temperatures (150 °C) for 1 week improves the performance of the films in DSSC to the same degree as calcination although the overall crystallinity remains lower. Reason for the good efficiency is that the porous structure stays intact and thus the dye molecules can be better adsorbed. Avoiding high temperatures during the preparation process of TiO₂ films for the application in DSSC enables the use of polymer substrates for the fabrication of flexible solar cells.     

Stability study of carbon-based counter electrodes in dye-sensitized solar cells

This study describes a systematic investigation of the stability of a carbon/TiO₂ counter electrode for use in dye-sensitized solar cells (DSSCs). In this system, nanoparticle additives were introduced by adding Ti-hydrogel. The additives then bound carbon particles and enhanced the adhesion of carbon materials to the conductive substrate. After introducing the Ti-hydrogel into the carbon paste, the carbon/Ti-hydrogel composited counter electrode (HC-CE) showed a better conductivity and stability compared with that of the carbon counter electrode (C-CE), while the catalytic activity was not influenced. The device based on the HC-CE showed superior power conversion efficiency (6.3%) and long-term stability over the device based on the C-CE (5.8%).     

TiO2 micro-flowers composed of nanotubes and their application to dye-sensitized solar cells

TiO₂ micro-flowers were made to bloom on Ti foil by the anodic oxidation of Ti-protruding dots with a cylindrical shape. Arrays of the Ti-protruding dots were prepared by photolithography, which consisted of coating the photoresists, attaching a patterned mask, illuminating with UV light, etching the Ti surface by reactive ion etching (RIE), and stripping the photoresist on the Ti foil. The procedure for the blooming of the TiO₂ micro-flowers was analyzed by field emission scanning electron microscopy (FESEM) as the anodizing time was increased. Photoelectrodes of dye-sensitized solar cells (DSCs) were fabricated using TiO₂ micro-flowers. Bare TiO₂ nanotube arrays were used for reference samples. The short-circuit current (J_sc) and the power conversion efficiency of the DSCs based on the TiO₂ micro-flowers were 4.340 mA/cm² and 1.517%, respectively. These values of DSCs based on TiO₂ micro-flowers were higher than those of bare samples. The TiO₂ micro-flowers had a larger surface area for dye adsorption compared to bare TiO₂ nanotube arrays, resulting in improved J_sc characteristics. The structure of the TiO₂ micro-flowers allowed it to adsorb dyes very effectively, also demonstrating the potential to achieve higher power conversion efficiency levels for DSCs compared to a bare TiO₂ nanotube array structure and the conventional TiO₂ nanoparticle structure.     

Dye-sensitized solar cells based on double-layered TiO2 composite films and enhanced photovoltaic performance

Dye-sensitized solar cells (DSSCs) are fabricated based on double-layered composite films of TiO₂ nanoparticles and hollow spheres. The photoelectric conversion performances of DSSCs based on nanoparticles/nanoparticles (PP), hollow spheres/hollow spheres (HH), hollow spheres/nanoparticles (HP), and nanoparticles/hollow spheres (PH) double-layered films are investigated, and their photo-electric conversion efficiencies are 4.33, 4.72, 4.93 and 5.28%, respectively. The enhanced performance of TiO₂ nanoparticles/hollow spheres double-layered composite film solar cells can be attributed to the combined effect of following factors. The light scattering of overlayer hollow spheres enhances harvesting light of the DSSCs and the underlayer TiO₂ nanoparticle layer ensures good electronic contact between film electrode and the F-doped tin oxide (FTO) glass substrate. Furthermore, the high surface areas and pore volume of TiO₂ hollow spheres are respectively beneficial to adsorption of dye molecules and transfer of electrolyte solution.     

Dye-sensitized solar cell based on optically transparent TiO2 nanocrystalline electrode prepared by atomized spray pyrolysis technique

Preparation of crack-free thin films of interconnected and non-agglomerated TiO₂ nanoparticles on electronically conducting fluorine doped tin oxide surfaces is instrumental in designing and developing transparent dye-sensitized solar cells (DSCs). A novel technique called “Atomized Spray Pyrolysis” (ASP) has been designed and developed to achieve such perfectly transparent thin films. Optical transmittance of TiO₂ films produced on FTO surface by this ASP method has been compared with those obtained by doctor-blading and by hand spray methods and found that the atomized spray pyrolysis technique give films with high transparency. Dye adsorption per gram of TiO₂ is 2.16 times higher in the sample produced by the ASP method when compared to the film produced by the hand spray method and is 1.60 times higher than that produced by the doctor-blading method using a commercially available TiO₂ nanocrystalline paste. SEM studies show the presence of interconnected discrete particles in the film produced by the ASP method. The fill factor (ff) remains almost constant for the cells with thickness from 6 μm to 13 μm but the highest photovoltage and photocurrent were found in ∼10 μm film based DSC which gave 8.2% conversion efficiency at AM 1.5 irradiation for cells of 0.25 cm² active area.     

Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

Role of surface state on the electron flow in modified TiO2 film incorporating carbon powder for a dye-sensitized solar cell

An investigation of surface-related traps in nanostructured TiO₂ films modified by the incorporation of carbon powder was conducted by the potential-step chronoamperometric method. For the modification of the morphology and surface state of the nanoporous TiO₂ electrode, the incorporation of carbon into the white TiO₂ powder was accomplished. In the chronoamperometric data, all of the transients showed an initial fast phase (<1 s) followed by a slower phase which is related to the trap filling process. The trap-filling period of the carbon incorporated TiO₂ film becomes longer, as the applied negative potential increases, due to the widely distributed traps induced by the increased surface area. Furthermore, the film capacitance was derived as a function of the applied bias by integrating the current to time curves of the chronoamperometric data. The accumulated charge of the carbon incorporated TiO₂ film increases prominently in two regions. The dominant increase shown in the positive region (−0.7 to −0.9 V vs. Ag/AgCl at pH 13) of the flat band potential implies that the electron occupancy in the surface-related traps is increased. At a more negative potential (below −1.2 V vs. Ag/AgCl), electrons from the conduction band of the TiO₂ film substantially influence the total current, thereby inducing an exponential increase in the current. Therefore, it is found that most of the traps are located in the positive region of the flat band potential, since the Fermi level of the nanostructured TiO₂ film is positioned at −1.14 V vs. Ag/AgCl at pH 13. The trap sites in the sub-bandgap region of the TiO₂ film are important in the electron transport of photoinjected electrons from dye molecules and partially charge recombination with redox electrolyte in operating dye-sensitized solar cell. The influence of charge trap formed by increased surface states on the electron transport and electron transfer was investigated by photovoltage and photocurrent transient measurements.     

A novel hierarchical Pt- and FTO-free counter electrode for dye-sensitized solar cell

A novel hierarchical Pt- and FTO-free counter electrode (CE) for the dye-sensitized solar cell (DSSC) was prepared by spin coating the mixture of TiO₂ nanoparticles and poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) solution onto the glass substrate. Compared with traditional Pt/FTO CE, the cost of the new CE is dramatically reduced by the application of bilayer TiO₂-PEDOT:PSS/PEDOT:PSS film and the glass substrate. The sheet resistance of this composite film is 35 Ω sq⁻¹ and is low enough to be used as an electrode. The surface morphologies of TiO₂-PEDOT:PSS layer and modified PEDOT:PSS layer were characterized by scanning electron microscope, which shows that the former had larger surface areas than the latter. Electrochemical impedance spectra and Tafel polarization curves prove that the catalytic activity of TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE is higher than that of PEDOT:PSS/FTO CE and is similar to Pt/FTO CE''s. This new fabricated device with TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE achieves a high power conversion efficiency (PCE) of 4.67%, reaching 91.39% of DSSC with Pt/FTO CE (5.11%).     

3-D solar cells by electrochemical-deposited Se layer as extremely-thin absorber and hole conducting layer on nanocrystalline TiO2 electrode

Ag₂S quantum dots were deposited on the surface of TiO₂ nanorod arrays by a two-step photodeposition. The prepared TiO₂ nanorod arrays as well as the Ag₂S deposited electrodes were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope, suggesting a large coverage of Ag₂S quantum dots on the ordered TiO₂ nanorod arrays. UV–vis absorption spectra of Ag₂S deposited electrodes show a broad absorption range of the visible light. The quantum dot-sensitized solar cells (QDSSCs) based on these electrodes were fabricated, and the photoelectrochemical properties were examined. A high photocurrent density of 10.25 mA/cm² with a conversion efficiency of 0.98% at AM 1.5 solar light of 100 mW/cm² was obtained with an optimal photodeposition time. The performance of the QDSSC at different incident light intensities was also investigated. The results display a better performance at a lower incident light level with a conversion efficiency of 1.25% at 47 mW/cm².     

Effect of TiO2 rutile nanorods on the photoelectrodes of dye-sensitized solar cells

In order to enhance the electron transport on the photoelectrodes of dye-sensitized solar cells, one-dimensional rutile nanorods were prepared using electrospun TiO₂ nanofibers. The grain size of the nanorods increased with increasing temperature. Electrochemical impedance spectroscopy measurements revealed reduced interface resistance of the cells with the one-dimensional rutile nanorods due to the improved electron transport and the enhanced electrolyte penetration. Intensity-modulated photocurrent/photovoltage spectroscopy showed that the one-dimensional rutile nanorods provided the electrons with a moving pathway and suppressed the recombination of photogenerated electrons. However, an excessive quantity of rutile nanorods created an obstacle to the electrons moving in the TiO₂ thin film. The photoelectrode with 7 wt.% rutile nanorods optimized the performance of the dye-sensitized solar cells.     

Conversion enhancement of flexible dye-sensitized solar cells based on TiO2 nanotube arrays with TiO2 nanoparticles by electrophoretic deposition

We prepared highly ordered titanium dioxide nanotube arrays (TNAs) by anodizing Ti foils in F⁻ containing electrolyte. The thickness and dye loading amount of TNAs were 26 μm and 1.06 × 10⁻⁷ mol cm⁻², respectively. TiO₂ nanoparticles (TNPs) were electrophoretically deposited on the inner wall of nanotube to produce coated nanotube arrays (TNAP). The dye loading was increased to 1.56 × 10⁻⁷ mol cm⁻², and the electron transport rate improved. TNAs and TNAP were sensitized with ruthenium dye N3 to yield dye-sensitized TiO₂ nanotube solar cells. The power conversion efficiency of TNA-based dye-sensitized solar cells (DSSCs) was 4.28%, whereas the efficiency of TNAP-based DSSCs increased to 6.28% when illuminated from the counter electrode. The increase of power conversion efficiency of TNAP-based DSSCs is ascribed to the increased surface area of TNAs and the faster electron transport rate.