BaEMg（BOa）2：Ce^3＋,Eu^2＋,Na^＋： A potential single-phased two colour borate phosphor for white light-emitting diodes

A two colour phosphor Ba 2 Mg(BO3)2:Ce3+,Eu2+,Na+ was synthesized using solid-state reaction method.Luminescence of Ba2Mg(BO3)2:Ce3+,Eu2+,Na+ showed 416 and 618 nm emission bands attributed to Ce3+ and Eu2+ emission, respectively. Energy transfer occurred from Ce3+ to Eu2+ through a significant overlap of Eu 2+ excitation spectrum with Ce3+ emission spectrum in Ba 2 Mg(BO3)2. They also showed that under the excitation of UV radiation, bluish or yellowish white light was generated by coupling a broad blue emission band and a red emission band.By combining with green phosphor, Ba2Mg(BO3 ):Ce3+,Eu2+,Na+ phosphor showed potential application for white light-emitting diodes (LEDs).     

Photoluminescence properties and effect of Bi~（3＋） dopant of Eu~（3＋） and Dy~（3＋） co-doped Sr_3V_2O_8

Photoluminescence properties of Sr 2.5 Dy 1/3-x Eu x V 2 O 8(x=0,0.06,0.12,0.18,0.24,0.33) were investigated.The excitation spectra included a broad band in the short wavelength region and several sharp lines in the longer wavelength region,and the spectral origin were discussed.The emission spectra were measured in two different exciting ways,i.e.,exciting the VO 4 group at 270 nm and the Eu 3+ ion at 398 nm,respectively,and the energy transferring process was reasonably suggested.Furthermore,multi-color emission could be achieved in Sr 2.5 Dy 1/3-x Eu x V 2 O 8,indicating that the studied samples had potential applications in the white light emitting diodes.Further investigation showed that reducing the concentration of Eu 3+ and Dy 3+ and introducing Bi 3+ as a sensitizer ion greatly enhanced the emission intensity.     

Luminescence properties of a new yellow long-lasting phosphorescence phosphor NaAlSiO_4:Eu~(2+),Ho~(3+)

A new aluminosilicate long-lasting phosphor with composition of NaAlSiO4:Eu2+,Ho3+ was synthesized and investigated. Under UV light excitation, the phosphor emitted yellow light corresponding to the characteristic emission of Eu2+ due to 5d-4f transition. Bright yellow phosphorescence sustaining for more than 30 min was observed after ceasing the excitation. The phosphorescence intensity decay obeyed a t–1 decay law, indicating a tunneling electron-hole recombination process in the phosphor. Four peaks appeared in the thermoluminescence curve and the ones at 322 and 370 K were thought to account for the long lasting phosphorescence at room temperature. The Ho3+ ion incorporated into the phosphor did not give any light but dramatically increased the intensities of both photoluminescence and phosphorescence via promoting defect levels in the phosphor.     

Synthesis and luminescence properties of Sr3-z（AlxSi1-x）O5-xFx：zCe^3＋phosphors

Sr3-z(Alx,Si1-x)O -5-xFx:zCe3+ phosphors were synthesized by high-temperature solid-state reaction.The structure and luminescence properties of phosphors with various Al/Si ratios and Ce3+ concentrations were characterized using various methods such as X-ray diffraction,photoluminescence excitation and photoluminescence spectra.XRD result displayed that a complete solid solution between Sr3AlO4F and Sr3SiO5 was formed.With the increasing of x value,a broader excitation band and stronger absorption appeared in the blue light region.Moreover,the emission band shifted to a shorter wavelength and the emission intensity reached a maximum at x=0.6.By adjusting the concentration of Ce3+,a widely tunable range of emission wavelength under the excitation of 460 nm was obtained from the green to yellow regions.In addition,the concentration and thermal quenching were also discussed.     

Ba1-xSrxMgSiO4:Eu2+,Mn2+: A novel tunable single-matrix tricolor phosphor for W-LED

The Ba1-xSrxMgSiO4:Eu2+,Mn2+ phosphors were prepared by solid-state reaction. Their photoluminescence properties were inves-tigated with fluorescence spectrum and CIE chromaticity. The emission color of Eu2+ in Ba0.98-xSrxMgSiO4:0.02Eu2+ could be tuned from green to blue by adjusting the content of Sr2+. The blue emission of Eu2+ overlapped well with the excitation spectra of Mn2+, leading to an ef-ficient energy transfer from Eu2+ to Mn2+ in Ba0.98-xSrxMg1-ySiO4:0.02Eu2+,yMn2+. Ba0.93Sr0.03Mg1-ySiO4:0.02Eu2+,yMn2+ could emit three ef-ficient broad bands at 440, 530 and 640 nm. The emission color of Ba0.93Sr0.03Mg1-ySiO4:0.02Eu2+,yMn2+ could be tuned from greenish blue to yellowish white by increasing the content of Mn2+ from 0 to 0.1. By changing the content of Sr2+/Mn2+, white-light with different hues could be conveniently obtained in the Ba1-xSrxMgSiO4:Eu2+,Mn2+ phosphors. The results showed that Ba1-xSrxMgSiO4:Eu2+,Mn2+ is a promising single-phased tricolor phosphor in the fabrication of W-LED.     

Phase structure and temperature dependent luminescence properties of Sr2LiSiO4F: Eu2+ and Sr2MgSi2O7: Eu2+ phosphors

Green-emitting Sr2LiSiO4F:Eu2+ and blue-emitting Sr2MgSi2O7:Eu2+ phosphors were synthesized by the conventional high temperature solid-state route,respectively.Their structures and photoluminescenee properties were comparatively investigated.It was found that the mixture phases of Sr2MgSi2O7 and SrF2 were obtained when a part of Sr2+ in Sr2LiSiO4F was replaced by some amount of Mg2+ in order to design the possible SrMgLiSiO4F:Eu2+ phosphor.Based on the photoluminescence analysis,Sr2LiSiO4F:Eu2+ phosphor exhibited a green broad emission band of main peak at 513 nm under the excitation of 365 nm,while the Sr2MgSi2O7:Eu2+ and SrMgLiSiO4F:Eu2+ phosphor showed blue emission centered at 467 nm.The temperature dependent photoluminescence properties and room temperature decay time for the three kinds of phosphors were also discussed in this paper.     

Luminescence properties of a single-host phosphor Bal.8-wSrwLi0.4SiO4： cea＋,Eu2＋,Mn2＋ for WLED

In order to obtain a single-host-white-light phosphor,a series of Ba1.8-w-x-y-zSrwLi0.4-xCexEuyMnzSiO4(BSLS:Ce3+,Eu2+,Mn2+)powder samples were synthesized via high temperature solid-state reaction.The structure and photoluminescence properties were investigated.Under ultraviolet excitation,the emission spectra contained three bands:the 370-470 nm blue band,the 470-570 nm green band and the 570-700 nm red band,which arose from the 5d→4f transitions of Ce3+ and Eu2+,and the 4T1→6A1 transition of Mn2+,respectively.The excitation spectra of the emissions of Ce3+ and Mn2+ ions showed the energy transfer from Ce3+ to Mn2+.White light emission was obtained from the tri-doped samples of appropriate doping concentration under 310-360 nm excitation.     

Origin of light emission and enhanced Eu3+photoluminescence in tin-containing glass

A barium-phosphate glass matrix was co-doped with Sn O and Eu2O3 for investigating on material luminescent properties. Optical absorption and X-ray photoelectron spectroscopy(XPS) were employed in the characterization of tin species. The prevalence of divalent tin was indicated by the XPS data in accord with a conspicuous absorption band detected around 285 nm ascribed to twofold-coordinated Sn centers(isoelectronic with Sn2+). Photoluminescence(PL) excitation spectra obtained by monitoring Eu3+ emission from the 5D0 state revealed a broad excitation band from about 250 to 340 nm, characteristic of donor/acceptor energy transfer. Under excitation of such at 290 nm, the co-doped material exhibited a bright whitish luminescence, and a four-fold enhanced Eu3+ emission relative to a purely Eu-doped reference. Time-resolved PL spectra recorded under the excitation at 290 nm exposed a broad band characteristic of the twofold-coordinated Sn centers and emission bands of Eu3+ ions, which appeared well separated in time in accord with their emission decay dynamics. The data suggested that light absorption took place at the Sn centers(donors) followed by energy transfer to Eu3+ ions(acceptors) which resulted in populating the 5D0 emitting state. Energy transfer pathways likely resulting in the enhanced Eu3+ photoluminescence and the consequential light emission were discussed.     

Intense blue-emitting Ca₂PO₄Cl:Eu²⁺ phosphor for near-ultraviolet converting white light-emitting diodes

A blue phosphor Ca2PO4Cl:Eu2+(CAP:Eu2+) was synthesized by solid state reaction.The Ca2PO4Cl:Eu2+ exhibited high quantum efficiency and excellent thermal stability.The luminescent intensity of Ca2PO4Cl:Eu2+ was found to be 128% under excitation at 380 nm,149% under 400 nm,and 247% under 420 nm as high as that of BaMgAl10O17:Eu2+.The optimal doping concentration was observed to 11 mol.% of CAP:Eu2+.The energy transfer between Eu2+ ions in CAP were occurred via electric multipolar interaction,and the critical transfer distance was estimated to be 1.26 nm.A mixture of blue-emitting Ca2PO4Cl:Eu2+,green-emitting(Ba,Sr)2SiO4:Eu2+ and red-emitting CaAlSiN3:Eu2+ phosphors were selected in conjunction with 400 nm chip to fabricate white LED devices.The average color-rendering index Ra and correlated color temperature(Tc) of the white LEDs were found to be 93.4 and 4590 K,respectively.The results indicated that it was a promising candidate as a blue-emitting phosphor for the near-UV white light-emitting diodes.     

Synthesis and photoluminescent properties of Sr2Si5N8：Eu^2＋red phosphors for white light-emitting diodes

Highly efficient Sr2Si5N8：Eu^2＋red emitting phosphor was successfully synthesized by a cost-effective direct silicon nitrida-tion and gas-reduction method. The effects of synthesis parameters, including reaction temperature, heating rate and gas species, on the crystal structure and photoluminescence of the prepared phosphors were studied. Single-phase Sr2Si5N8：Eu^2＋phosphor was ob-tained at 1500℃ with a heating rate of 300℃/h under NH3-1 vol.%CH4 atmosphere using starting silicon and oxide powders. Silicon powder and high heating rate favored the achievement of the pure Sr2Si5N8 phase. Under near-UV to blue light excitation, the obtained Sr2Si5N8：Eu2＋phosphor showed a board red emission band centered at about 625 nm, which agreed well with the phosphors prepared by the conventional solid-state reaction. The possible reaction mechanism was also proposed based on the experimental observations.     

Infrared to near-infrared and visible upconversion photoluminescence of LiYbF4：Er3＋ nanorods

Colloidal LiYbF4:Er3+ nanorods were synthesized in an aqueous system which had the ratio of length to diameter of～2.These LiYbF4:Er3+ nanorods emitted intense upconversion light under excitation of infrared at 1488 nm.Importantly,the intensities of two-and three-photon anti-Stokes upconversion PL bands were observed which were comparable to that of the Stokes emission under excitation with low power density.The plots of excitation power density versus emission intensity indicated that all the emissions centered at 549,668,and 978 nm took a two-photon upconversion process.However,it could be simply deduced that the energy of two photons of 1488 nm were inadequate to produce a photon of 668 or 549 nm.For this conflict,the shape and saturation effects in the intermediate energy states were introduced to demonstrate the corresponding upconversion processes.     

White light emission of Eu^3＋/Ag co-doped Y2Si2O7

The Eu3+/Ag co-doped rare earth disilicate Y2Si2O7 microcrystal was synthesized by sol-gel method. Through controlling the thermal treatment process of Y2Si2O7:Eu3+/Ag precursor, various phases(amorphous, α, β, γ, δ) were prepared. White light emission was observed under UV light excitation in the samples heavily doped with Ag. The white light was realized by combining the intense red emission of Eu3+, the green emission attributed to the very small molecule-like, non-plasmonic Ag particles(ML-Ag-particles), and the blue emission due to Ag ions. Results demonstrated that Eu3+/Ag co-doped Y2Si2O7 microcrystal could be potentially applied as white light emission phosphors for UV LED chips.     

Luminescent properties of Eu~（3＋） doped Gd_2WO_6 and Gd_2（WO_4）_3 nanophosphors prepared via co-precipitation method

Eu3+ doped Gd2WO6 and Gd2(WO4)3 nanophosphors with different concentrations were prepared via a co-precipitation method. The structure and morphology of the nanocrystal samples were characterized by using X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM), respectively. The emission spectra and excitation spectra of samples were measured. J-O parameters and quantum efficiencies of Eu3+ 5D0 energy level were calculated, and the concentration quenching of Eu3+ luminescence in different matrixes were studied. The results indicated that effective Eu3+:5D0-7F2 red luminescence could be achieved while excited by 395 nm near-UV light and 465 nm blue light in Gd2WO6 host, which was similar to the familiar Gd2(WO4)3:Eu. Therefore, the Gd2WO6:Eu red phosphors might have a potential application for white LED.     

Yellow upconversion luminescence in Ho3＋/yb3＋ co-doped Gd2Mo3O9 phosphor

The strong yellow upconversion (UC) light emission was observed in Ho3+/Yb3+co-doped Gd2Mo3O9 phosphor under the excitation of 980 nm diode laser. The phosphors were synthesized by the traditional soli...     

Luminescent properties of red phosphors K2Ba（MoO4）2：Eu3＋ for white light emitting diodes

K2Ba(MoO4)2:Eu3+ phosphors were synthesized by solid-state reaction. The emission and excitation spectra of K2 Ba(MoO4)2:Eu3+ phosphors exhibited that the phosphors could be effectively excited by near ultraviolet (394 nm) and blue (465 nm) light, and emitted red light at 616 nm. The influence of Eu3+concentration, sintering temperature and charge compensators (K+, Na+ or Li+ ) on the emission intensity were investigated. The results indicated that concentration quenching of Eu3+ was not observed within 30mol.% Eu 3+, 600 oC was a suitable sintering temperature for preparation of K2 Ba(MoO4)2:Eu3+phosphors, and K+ ions gave the best improvement to enhance the emission intensity. The CIE chromaticity coordinates of K2 Ba(MoO4)2:0.05Eu3+phosphor were calculated to be (0.68, 0.32), and color purity was 97.4%.     

Luminescent Properties of SrGa2S4 :Eu and Its Application in Green-LEDs

Phosphor SrGa2S4Eu2 was synthesized with a high temperature solid state reaction.Its absorption spectrum, photoluminescence spectra, and fluorescence lifetime were studied in details.The excitation spectrum extended from UV to visible light region, and matched the emission of GaN chip.(Sr1-xEux)Ga2S4 emits strong green light and the concentration quenching did not occur; while the thermal quenching was evident.The emission peak shifted to long wavelength with increasing Eu2 concentration because of the changing of the crystal field strength.The lifetime of Eu2 ion was in the order of microsecond, which was reasonable for d→f transition.The electroluminescence spectrum of as-fabricated PC-LED at IF=20 mA was measured and most of the blue light of blue-LED chip at 460 nm was absorbed by the phosphor and simultaneously down-converted into an intensive green light at 540 nm.The color coordinate was (0.32, 0.63).SrGa2S4Eu2 was a promising phosphor for GaN-based green LEDs.     

Photoluminescence properties of a blue-emitting phosphor Eu2+-activated Ca3ZnAl4O10

A new aluminate host material Ca3ZnAl4O10 doped with Eu2+ was prepared by a high-temperature solid-state reaction method, and a pure crystalline phase of Ca3ZnAl4O10 was confirmed with X-ray powder diffraction (XRD) measurement. The luminescent property was investigated with excitation and emission spectra. The phosphor could be excited by UV light from 220 nm to 400 nm and emitted a blue luminescence peaked at 450 nm, which corresponded to the 4f65d1→4f7 transition of Eu2+ ions. The dependence of luminesce...     

New Rare-Earth Containing （Sr1- yEuy）2 Al2Si10S14O4 Phosphors for Light-Emitting Diodes

Remarkable progress was made in the development of white-light-emitting diodes （LEDs）. White LEDs provided a light element having a semiconductor InGaN light-emitting chip （blue or UV LEDs） and luminescent phosphors. Here we reported the sialon s-phase of （Sr,Eu）2A12Si10N14O4. Eu^2＋ activator ions that were substituted for the strontium site represented a new type of yeUow-green phosphor that could be excited by blue LEDs used for application in the fabrication of white LEDs.     

Rare earth （Eu2＋,ce3＋） activated BaAIESi2O8 blue emitting phosphor

Blue emitting rare earth（Eu2＋,Ce3＋） doped BaAl2Si2O8 phosphors were synthesized by combustion methods at 600 oC. BaAl2Si2O8： Eu2＋ phosphor showed isolated broad blue emission band at 455 nm, when it was excited with the wavelength of 329 nm. Whereas BaAl2Si2O8：Ce3＋ phosphor exhibited blue emission band at 442 nm, under 303 nm excitation wavelength. These observed emission bands of Eu2＋ and Ce3＋ ions corresponded to 5d-4f allowed transitions. The position of emission band was calculated by using the equationE=Q[1-〔V/4〕^1/V）]× 10 （nEar/80）Also the spin orbit splitting difference in the ground state levels of Ce3＋ ion was studied by Gaussian curve fitting. Broad absorption and emission bands in blue regions made prepared phosphors a promising blue host for the white-LEDs.     

Eu2＋ and Dy3＋ codoped （Ca,Sr）7（SiO3）6Cl2 highly efficient yellow phosphor

Eu2+ and Dy3+ codoped(Ca,Sr)7(SiO3)6Cl2 yellow phosphors were successfully synthesized by self-flux method. The structure, morphology and photoluminescence properties were investigated by X-ray diffraction(XRD), scanning electron microscopy(SEM) and photoluminescence spectra. The as-prepared phosphor showed a broad emission spectrum centered at 550 nm for Eu2+single-doped phosphor, while located at 548–544 nm for the Eu2+, Dy3+ codoped samples under excitation at 380 nm light. The emission intensity was greatly improved when Dy3+ was doped into the(Ca,Sr)7(SiO3)6Cl2:Eu2+ system. The composition-optimized sample with 3 mol.% of Dy3+ and constant 10 mol.% of Eu2+ exhibited a 220% PL enhancement compared to the phosphor with 10 mol.% Eu2+ single-doped. Meanwhile, it was found that the quantum efficiency of phosphor namely(Ca,Sr)7(SiO3)6Cl2:3 mol.% Dy3+, 10 mol.% Eu2+ could get up to 24.6%. The synthesized yellow-emitting(Ca,Sr)7(SiO3)6Cl2:Dy3+,Eu2+ is a promising candidate as high-efficiency yellow phosphor for NUV-excited white LEDs.