聚亚胺亚胺醚醚酮酮空心微球的制备

以1,4–双–(4′–溴苯酰基)苯和4,4′–(1,4–苯二氧基)双苯胺为单体,以三(二亚苄基丙酮)二钯为催化剂,1,1′–联萘–2,2′–二苯膦(BINAP)为配体,由钯催化的氨基化反应缩聚合成了可溶性聚亚胺亚胺醚醚酮酮(PIIEEKK)。以PIIEEKK为原料,用微封装法制备了聚合物空心微球。     

聚芳醚酮/含甲基侧基聚芳醚砜醚酮酮的合成与表征

以2，2’-二甲基-4,4'-二苯氧基二苯砜(o-CH3-DPODPS)、二苯醚(DPE)和对苯二甲酰氯(TPC)为单体，在无水A1C13、1，2-二氯乙烷和N，N-二甲基甲酰胺存在下，通过低温溶液缩聚反应。合成了一系列新型含甲基侧基的聚芳醚酮／聚芳醚砜无规共聚物。用FT-IR，WAXD，DSC和TG等方法对聚合物进行了表征。结果表明，随着2,2'-二甲基-4，4'-二苯氧基二苯砜含量的增加，共聚物的玻璃化转变温度逐渐提高，熔融温度则逐渐下降。     

含氰侧基联苯型聚芳醚醚酮酮的合成及表征

通过一种反应条件较为温和的反应新工艺,合成联苯二甲酰氯,即4,4’-二氯甲酰基联苯(BC IBP)。然后,在无水A lC l3及N-甲基吡咯烷酮(NMP)/1,2-二氯乙烷(DCE)复合溶剂的存在下,将2,6-二苯氧基苯甲腈(DPOBN)与BC IBP进行低温缩聚反应,合成了一类新型含氰侧基联苯型聚芳醚醚酮酮。用IR,DSC,TG,WAXD及元素分析等方法对其结构和性能进行了表征。结果表明,所合成的聚合物具有预期结构且为非晶态聚合物;其玻璃化转变温度(Tg)为211℃,在氮气气氛中及在空气气氛中的热分解5%的温度(Td)分别为523℃及498℃,说明其具有突出的耐高温性能;聚合物除了能在浓H2SO4,CF3COOH/CHC l3等强质子性溶剂当中溶解外,对其他的溶剂均不溶解,说明聚合物具有优异的耐化学腐蚀性能。     

含氯侧基聚芳醚酮醚酮酮的合成与表征

以α-萘酚为原料，通过和4，4′-二氟二苯酮在N，N-二甲基乙酰胺（DMAC）及K2CO3中的缩合反应制备了一种含萘环的新型芳醚单体4，4′-二（α-萘氧基）二苯酮（DNBP），将其分别与2，5-二氯对苯二甲酰氯（DCTPC）。对苯二甲酰氯（TPC）等芳二酰氯通过在NMP/AlCl3/ClCH2CH2Cl复合溶剂/催化剂体系中的低温溶液进行亲电共缩聚反应，合成了一系列在分子主链芳环上引入侧基氯原子的同时，又在主链中引入刚性萘环结构的新型聚芳醚酮醚酮酮无规共聚物。     

新型含偶氮结构聚芳醚砜醚酮酮的合成与表征

在无水AlCl3及N-甲基吡咯烷酮(NMP)/1,2-二氯乙烷(DCE)复合溶剂的存在下,将含砜基芳二醚类单体与含偶氮苯结构芳二甲酰氯进行低温付-克缩聚反应,合成了一类新型含偶氮结构聚芳醚砜醚酮酮树脂。用IR、TG、WAXD及元素分析等技术进行了结构表征和性能测试。结果表明:所合成的聚合物树脂具有预期结构且为非晶态聚合物;在N2气氛中质量损失5%的温度(Td)分别为445～463℃;聚合物除了能在浓硫酸、CF3COOH/CHCl3等强极性质子型溶剂中溶解外,还能溶解于N-甲基吡咯烷酮(NMP)、N,N-二甲基甲酰胺(DMF)、二甲基亚砜(DMSO)等强极性非质子型溶剂中,也能在普通溶剂,如氯仿(CHCl3)、1,2-二氯乙烷(DCE)、四氢呋喃(THF)等中溶解。     

耐高温含氟聚芳醚酮和聚芳醚砜的合成与性能研究

通过三步反应合成新的含氟双酚单体3,4-二氟苯基对苯二酚,由该含氟双酚单体、4-氟苯基对苯二酚、邻苯基对苯二酚分别与4,4′-二氟二苯酮、4,4′-二氯二苯砜经亲核缩聚反应,制备了一系列新型聚芳醚酮和聚芳醚砜。采用 FT-IR、DSC、TGA及XRD手段等对聚合物的结构和性能进行了表征和研究,结果表明：合成的聚芳醚酮和聚芳醚砜具有优异的耐热性能,玻璃化转变温度分别在150~159 ℃和177~196 ℃之间,氮气中5 %热失重温度分别在527 ℃和507 ℃以上。合成的聚芳醚酮和聚芳醚砜具有良好的溶解性,室温下能溶解在N-甲基吡咯烷酮、二甲基乙酰胺、氯仿等有机溶剂中。     

聚芳醚砜酮纺丝溶液流变性能研究

研究了含二氮杂萘酮结构聚芳醚砜酮 (PPESK)的 N-甲基吡咯烷硐 (NMP)溶液体系的粘度对浓度、温度和切变速率以及砜酮比的依赖性。结果表明 ,该溶液的粘度随剪切速率的提高而降低 ,为非牛顿流体 ;粘度随溶液浓度的增大而增大 ,与浓度的高次幂成正比 ,随砜酮比的增加而下降 ;温度对粘度的影响服从 Arrhenius公式。用该溶液纺制的纤维经测定力学性能较好。     

高性能聚芳醚酮的发展及应用

综述了聚醚酮、聚醚醚酮、聚醚醚酮酮、聚醚酮酮、聚醚酮醚酮酮等5类高性能聚芳醚酮的性能、合成方法及其改性研究进展等,并介绍了聚芳醚酮的应用情况,指出聚芳醚酮的发展趋势是通过开发新的合成技术或者改性途径,在不影响其主要性能的前提下降低生产成本.     

含二氮杂萘酮结构聚芳醚酮和聚芳醚砜研究进展

综述了含二氮杂萘酮结构的聚芳醚酮和聚芳醚砜的结构性能及其合成、改性、应用研究进展。     

阳离子-π动态交联高性能聚芳吲哚醚酮的构筑

玻璃化转变温度(T_g)和热稳定性是聚合物重要的物理性能,影响了材料的应用领域。交联被认为是提高T_g和热稳定性的重要方法之一。本文以4,4-二氟二苯酮和4-羟基吲哚为单体,通过亲核取代反应成功制备了线型聚芳吲哚醚酮(PINEK),并通过简易的浸泡碱性水溶液的方式实现了PINEK的阳离子-π动态交联。与传统的线型聚醚醚酮(PEEK)和PINEK相比,交联型聚芳吲哚醚酮(C-PINEK)表现出较高的T_g(T_g=251℃)和优异的热分解温度(T_d=501℃)。     

Effect of dihydroxydiphenyl ether on poly(ether ether ketone)

A series of modified poly(ether ether ketone) (PEEK) polymers were synthesized by introduction of addition ether groups from dihydroxydiphenyl ether (DHDE) into the PEEK structure. The inherent viscosity of the DHDE-modified PEEK increased with reaction time at 320 °C. DSC thermograms showed the melting points of the obtained PEEK decreased with the increase of the DHDE content in the backbone. The degradation temperature (T_d) was slightly decreased by the introduction of DHDE. The crystallinity as measured via the X-ray diffraction (XRD) increases with the introduction of DHDE into the modified PEEK. The crystalline structure was identified as an orthorhombic structure with lattice constants a = 7.72 Å, b = 5.86 Å, and c = 10.24 Å. Due to the glass transition temperature (T_g) and the melting temperature (T_m) decreasing with the increase of the DHDE content in the reaction system. the processability of the resultant PEEK could be improved through this DHDE modification.     

Fine poly(ether ether ketone) powders

The physical form of polymers is often important for carrying out subsequent processing operations. For example, fine powders are desirable for molding and sintering compounds because they consolidate to produce void free components. The objective of this work is to prepare fine polymeric particulates suitable for processing into fiber reinforced polymer matrix composites. Micron size particles of poly(ether ether ketone) (PEEK) were prepared by rapidly quenching solutions of these materials. PEEK pellets were dissolved at temperatures near the PEEK melting point in a mixture of terphenyls and quaterphenyls; then the solution was quenched to a temperature between the T_g and T_m (≈ 225°C) by adding a room temperature eutectic mixture of diphenyl ether and biphenyl. A supersaturated, metastable solution of PEEK resulted, causing rapid nucleation. Fine PEEK particles rapidly crystallized from this solution. The average particle size was measured using transmission electron microscopy, atomic force microscopy, and by light scattering of aqueous suspensions which had been fractionated by centrifugation. The average particle diameter was about 0.6 μm. Three dimensional photomicrographs obtained via atomic force microscopy showed some aggregates in the suspensions. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1571–1578, 1997     

Synthesis and characterization of poly(ether ketone ether ketone ketone)/poly(ether ether ketone ketone) copolymers containing naphthalene and pendant cyano groups

2,6‐Bis(β‐naphthoxy)benzonitrile (BNOBN) was synthesized by reaction of β‐naphthol with 2,6‐difluorobenzonitrile in N‐methyl‐2‐pyrrolidone (NMP) in the presence of KOH and K₂CO₃. Poly(ether ketone ether ketone ketone)(PEKEKK) /poly(ether ether ketone ketone) (PEEKK) copolymers containing naphthalene and pendant cyano groups were obtained by electrophilic Friedel‐Crafts polycondensation of terephthaloyl chloride (TPC) with varying mole proportions of 4,4′‐diphenoxybenzophenone (DPOBP) and 2,6‐bis(β‐naphthoxy)benzonitrile (BNOBN) using 1,2‐dichloroethane (DCE) as solvent and NMP as Lewis base in the presence of anhydrous AlCl₃. The resulting polymers were characterized by various analytical techniques, such as FTIR, DSC, TG, and WAXD. The results indicated that the crystallinity and melting temperature of the polymers decreased with increase in concentration of the BNOBN units in the polymer, the glass transition temperature of the polymers increased with increase in concentration of the BNOBN units in the polymer. Thermogravimetric studies showed that all the polymers were stable up to 536°C in N₂ atmosphere. The copolymers have good resistance to acidity, alkali, and organic solvents. Because of the melting temperature (T_m) depression with increase in the BNOBN content in the reaction system, the processability of the resultant coplymers could be effectively improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

Miscibility and crystallization behavior of poly(ether ether ketone ketone)/poly(ether imide) blends

The miscibility and crystallization behavior of poly(ether ether ketone ketone) (PEEKK)/poly(ether imide) (PEI) blends prepared by melt‐mixing were investigated by differential scanning calorimetry. The blends showed a single glass transition temperature, which increased with increasing PEI content, indicating that PEEKK and PEI are completely miscible in the amorphous phase over the studied composition range (weight ratio: 90/10–60/40). The cold crystallization of PEEKK blended with PEI was retarded by the presence of PEI, as is apparent from the increase of the cold crystallization temperature and decrease of the normalized crystallinity for the samples anealed at 300°C with increasing PEI content. Although the depression of the apparent melting temperature of PEEKK blended with PEI was observed, there was no evidence of depression in the equilibrium melting temperature. The analysis of the isothermal crystallization at 313–321°C from the melt of PEEKK/PEI (100/0, 90/10, and 80/20) blends suggested that the retardation of crystallization of PEEKK is caused by the increase of the crystal surface free energy in addition to the decrease of the mobility by blending PEI with a high glass transition temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 769–775, 2001     

Synthesis and characterization of poly(ether amide ether ketone)/poly(ether ketone ketone) copolymers

A new monomer, N,N′‐bis(4‐phenoxybenzoyl)‐m‐phenylenediamine (BPPD), was prepared by condensation of m‐phenylenediamine with 4‐phenoxybenzoyl chloride in N,N‐dimethylacetamide (DMAc). A series of novel poly(ether amide ether ketone) (PEAEK)/poly(ether ketone ketone) (PEKK) copolymers were synthesized by the electrophilic Friedel‐Crafts solution copolycondensation of terephthaloyl chloride (TPC) with a mixture of diphenyl ether (DPE) and BPPD, over a wide range of DPE/BPPD molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The influence of reaction conditions on the preparation of copolymers was examined. The copolymers obtained were characterized by different physicochemical techniques. The copolymers with 10–25 mol % BPPD were semicrystalline and had remarkably increased T_gs over commercially available PEEK and PEKK due to the incorporation of amide linkages in the main chains. The copolymers III and IV with 20–25 mol % BPPD had not only high T_gs of 184–188°C, but also moderate T_ms of 323–344°C, having good potential for the melt processing. The copolymers III and IV had tensile strengths of 103.7–105.3 MPa, Young's moduli of 3.04–3.11 GPa, and elongations at break of 8–9% and exhibited outstanding thermal stability and good resistance to organic solvents. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of copolymers of poly(ether ketone ketone) and poly(ether amide ether amide ether ketone ketone)

Poly(aryl ether ketone)s (PAEKs) are a class of high‐performance engineering thermoplastics known for their excellent combination of chemical, physical and mechanical properties, and the synthesis of semicrystalline PAEKs with increased glass transition temperatures (T_g) is of much interest. In the work reported, a series of novel copolymers of poly(ether ketone ketone) (PEKK) and poly(ether amide ether amide ether ketone ketone) were synthesized by electrophilic solution polycondensation of terephthaloyl chloride with a mixture of diphenyl ether and N,N′‐bis(4‐phenoxybenzoyl)‐4,4′‐diaminodiphenyl ether (BPBDAE) under mild conditions. The copolymers obtained were characterized using various physicochemical techniques. The copolymers with 10–35 mol% BPBDAE are semicrystalline and have markedly increased T_g over commercially available poly(ether ether ketone) and PEKK due to the incorporation of amide linkages in the main chain. The copolymers with 30–35 mol% BPBDAE not only have high T_g of 178–186 °C, but also moderate melting temperatures of 335–339 °C, having good potential for melt processing. The copolymers with 30–35 mol% BPBDAE have tensile strengths of 102.4–103.8 MPa, Young's moduli of 2.33–2.45 GPa and elongations at break of 11.7–13.2%, and exhibit high thermal stability and good resistance to organic solvents. Copyright © 2010 Society of Chemical Industry     

Synthesis and properties of poly(aryl ether ketone ketone)/poly(aryl ether ether ketone ketone) copolymers with pendant cyano groups

2,6‐Diphenoxybenzonitrile (DPOBN) was synthesized by reaction of phenol with 2,6‐difluorobenzonitrile in N‐methyl‐2‐pyrrolidone in the presence of KOH and K₂CO₃. Poly(aryl ether ketone ketone)/poly(aryl ether ether ketone ketone) copolymers with pendant cyano groups were prepared by the Friedel–Crafts electrophilic substitution reaction of terephthaloyl chloride with varying mole proportions of diphenyl ether and DPOBN using 1,2‐dichloroethane as solvent and N‐methyl‐2‐pyrrolidone as Lewis base in the presence of anhydrous AlCl₃. The resulting polymers were characterized by various analytical techniques, such as FT‐IR, differential scanning calorimeter, thermal gravimetric analysis, and wide‐angle X‐ray diffraction. The crystallinity and melting temperature of the polymers were found to decrease with increase in concentration of the DPOBN units in the polymer. Thermogravimetric studies showed that all the polymers were stable up to 514°C in N₂ atmosphere. The glass transition temperature was found to increase with increase in concentration of the DPOBN units in the polymer when the molar ratios of DPOBN to DPE ranged from 10/90 to 30/70. The copolymers containing 30–40 mol % of the DPOBN units exhibit excellent thermostability at (350 ± 10)°C and have good resistance to acidity, alkali, and organic solvents. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3601–3606, 2007     

Rheological properties in blends of poly(aryl ether ether ketone) and liquid crystalline poly(aryl ether ketone)

Rheological properties of the blends of poly(aryl ether ether ketone) (PEEK) with liquid crystalline poly(aryl ether ketone) containing substituted 3‐trifluoromethylbenzene side group (F‐PAEK), prepared by solution precipitation, have been investigated by rheometer. Dynamic rheological behaviors of the blends under the oscillatory shear mode are strongly dependent on blend composition. For PEEK‐rich blends, the systems show flow curves similar to those of the pure PEEK, i.e., dynamic storage modulus G′ is larger than dynamic loss modulus G″, showing the feature of elastic fluid. For F‐PAEK‐rich systems, the rheological behavior of the blends has a resemblance to pure F‐PAEK, i.e., G″ is greater than G′, showing the characteristic of viscous fluid. When the PEEK content is in the range of 50–70%, the blends exhibit an unusual rheological behavior, which is the result of phase inversion between the two components. Moreover, as a whole, the complex viscosity values of the blends are between those of two pure polymers and decrease with increasing F‐PAEK content. However, at 50% weight fraction of PEEK, the viscosity‐composition curves exhibit a local maximum, which may be mainly attributed to the phase separation of two components at such a composition. The changes of G′ and G″ with composition show a trend similar to that of complex viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4040–4044, 2006     

聚苯酯对聚醚醚酮结晶行为的影响

用模压法制备了聚苯酯(Ekonol)／聚醚醚酮(PEEK)复合材料，通过X射线衍射(XRD)、差示扫描量热分析(DSC)考察了PEEK的结晶行为，并测定了复合材料的熔点、结晶温度和玻璃化转变温度。结果表明：Ekonol含量的大小对PEEK的结晶行为产生了直接影响，PEEK的相对结晶度随着Ekonol含量的增加而提高；Ekonol含量小于30％时，对复合材料的熔点、结晶温度和玻璃化转变温度影响不大，但含量大于30％时，材料的结晶温度、熔融温度下降，玻璃化转变温度提高。