10-Gb/s limiting amplifier and laser/modulator driver in 0.18-/spl mu/m CMOS technology

A limiting amplifier incorporates active feedback, inductive peaking, and negative Miller capacitance to achieve a voltage gain of 50 dB, a bandwidth of 9.4 GHz, and a sensitivity of 4.6 mV/sub pp/ for a bit-error rate of 10/sup -12/ while consuming 150 mW. A driver employs T-coil peaking and negative impedance conversion to achieve operation at 10 Gb/s while delivering a current of 100 mA to 25-/spl Omega/ lasers or a voltage swing of 2 V/sub pp/ to 50-/spl Omega/ modulators with a power dissipation of 675 mW. Fabricated in 0.18-/spl mu/m CMOS technology, both prototypes operate with a 1.8-V supply.     

A high-voltage output driver in a 2.5-V 0.25-/spl mu/m CMOS technology

The design of a high-voltage output driver in a digital 0.25-/spl mu/m 2.5-V technology is presented. The use of stacked devices with a self-biased cascode topology allows the driver to operate at three times the nominal supply voltage. Oxide stress and hot carrier degradation is minimized since the driver operates within the voltage limits imposed by the design rules of a mainstream CMOS technology. The proposed high-voltage architecture uses a switching output stage. The realized prototype delivers an output swing of 6.46 V to a 50-/spl Omega/ load with a 7.5-V supply and an input square wave of 10 MHz. A PWM signal with a dual-tone sinusoid at 70 kHz and 250 kHz results in an IM3 of -65 dB and an IM2 of -67 dB. The on-resistance is 5.9 /spl Omega/.     

A 3-V fully differential distributed limiting driver for 40-Gb/s optical transmission systems

A fully differential 40-Gb/s electro-absorption modulator driver is presented. Based on a distributed limiting architecture, the circuit can supply up to 3.0-V/sub pp/ (peak-to-peak) per side in a 50-/spl Omega/ load at data rates as high as 44 Gb/s. Both the input and the output are internally matched to 50 /spl Omega/ and exhibit return loss of better than 10 dB up to 50 GHz. Additional features of the driver include the use of a single -5.2-V supply, output swing control (1.7-3.0-V/sub pp/ per side), dc output offset control (-0.15 V to -1.1 V), and pulsewidth control (30% to 66%). The driver architecture was optimized based on a comprehensive analytical derivation of the frequency response of cascaded source-coupled field-effect transistor logic blocks using both single and double source-follower topologies.     

A 3.3-V CMOS adaptive analog video line driver with low distortion performance

An analog line driver for video applications is presented. Utilizing a class-AB error amplifier structure, the design achieved 1.2-V peak-to-peak output swing with better than 42-dB linearity for frequencies up to 5 MHz. An adaptive tuning scheme for output impedance matching using peak detection is used to provide uniform performance across line impedance variations. The circuit is designed in AMI 0.5-/spl mu/m CMOS technology and has a tuning range of 70-180 /spl Omega/ with a power consumption of about 26.4 mW at 75-/spl Omega/ load.     

An efficient CMOS line driver for 1.544-Mb/s T1 and 2.048-Mb/s E1 applications

A CMOS operational amplifier (OPAMP) for use as a line driver for high-speed T1/E1 data communication link is described. The differential output swing, using a single 3.3-V power supply, is 5.2-V peak-to-peak on a 20-/spl Omega/ load. Novel circuits are used to control the closed-loop output impedance, quiescent bias current, and frequency compensation to ensure stable operation over varying temperature and load conditions. A special circuitry tristates the output in case of power-supply failure. The OPAMP achieves a unity-gain bandwidth of 35 MHz with only 10 mA of quiescent current. A new output-current-sense circuitry is used to provide a current feedback to adjust the output impedance for proper line termination as well as to provide short-circuit protection from excessive output currents. Using 0.35-/spl mu/m n-well CMOS technology, the amplifier occupies 0.69 mm/sup 2/ of area.     

New low-voltage class AB/AB CMOS op amp with rail-to-rail input/output swing

A new low-voltage CMOS Class AB/AB fully differential opamp with rail-to-rail input/output swing and supply voltage lower than two V/sub GS/ drops is presented. The scheme is based on combining floating-gate transistors and Class AB input and output stages. The op amp is characterized by low static power consumption and enhanced slew-rate. Moreover the proposed opamp does not suffer from typical reliability problems related to initial charge trapped in the floating-gate devices. Simulation and experimental results in 0.5-/spl mu/m CMOS technology verify the scheme operating with /spl plusmn/0.9-V supplies and close to rail-to-rail input and output swing.     

Low supply voltage high-performance CMOS current mirror with low input and output voltage requirements

This paper presents a scheme for the efficient implementation of a low supply voltage continuous-time high-performance CMOS current mirror with low input and output voltage requirements. This circuit combines a shunt input feedback and a regulated cascode output stage to achieve low input resistance and very high output resistance. It can be used as a high-precision current mirror in analog and mixed signal circuits with a power supply close to a transistor's threshold voltage. The proposed current mirror has been simulated and a bandwidth of 40 MHz has been obtained. An experimental chip prototype has been sent for fabrication and has been experimentally verified, obtaining 0.15-V input-output voltage requirements, 100-/spl Omega/ input resistance, and more than 200-M/spl Omega/ (G/spl Omega/ ideally) output resistance with a 1.2-V supply in a standard CMOS technology.     

On-panel output buffer with offset compensation technique for data driver in LTPS technology

To overcome the offset voltage (V/sub OS/) of output buffer due to large variation on characteristics of thin-film transistor (TFT) in low-temperature polysilicon (LTPS) technology, a class-B output buffer with offset compensation circuit for the data driver is presented in this paper. This proposed class-B output buffer can operate at 50-kHz operation frequency with a 2-8-V output swing for extended graphic array (XGA) application, and it has been demonstrated in 3-/spl mu/m LTPS technology. Using the offset compensation technique, the V/sub OS/ of output buffer can be controlled within /spl plusmn/100 mV under 2-to-8 V signal operation to achieve a high resolution and quality liquid crystal display (LCD) panel.     

A high f/sub OSC//f/sub T/ ratio VCO in SiGe BiCMOS technology

A 37-GHz voltage controlled oscillator (VCO) fabricated in IBM's 47-GHz SiGe BiCMOS technology is presented. The VCO achieves a phase noise of -81dBc/Hz at 1-MHz offset from the carrier while delivering an output power of -30dBm to 50 /spl Omega/ buffers. Drawing 15-mA of dc current from a 3-V power supply the VCO occupies 350/spl mu/m/spl times/280/spl mu/m of silicon area. Capacitive emitter degeneration and compact layout are used to achieve high f/sub OSC//f/sub T/ ratio.     

6-k/spl Omega/ 43-Gb/s differential transimpedance-limiting amplifier with auto-zero feedback and high dynamic range

A high-gain, 43-Gb/s InP HBT transimpedance-limiting amplifier (TIALA) with 100-/spl mu/A/sub pp/ sensitivity and 6 mA/sub pp/ input overload current is presented. The circuit also operates as a limiting amplifier with 40-dB differential gain, better than 15-dB input return loss, and a record-breaking sensitivity of 8 mV/sub pp/ at 43 Gb/s. It features a differential TIA stage with inductive noise suppression in the feedback network and consumes less than 450mW from a single 3.3-V supply. The TIALA has 6-k/spl Omega/ (76dB/spl Omega/) differential transimpedance gain and 35-GHz bandwidth and comprises the transimpedance and limiting gain functions, an auto-zero dc feedback circuit, signal level monitor, and slicing level adjust functions. Other important features include 45-dB isolation and 800-mV/sub pp/ differential output.     

A low-power 5-70-MHz seventh-order log-domain filter with programmable boost, group delay, and gain for hard disk drive applications

A seventh-order 0.05/spl deg/ equiripple linear-phase continuous-time filter employing log-domain-based instantaneous companding was designed and integrated in a mature bipolar process. The amount of boost (up to 13 dB) and group-delay adjustment (/spl plusmn/30%) are digitally programmable. The dc gain is controllable up to 10 dB, and the -3-dB frequency (f/sub c/) is tunable from 5 to 70 MHz. The output swing for 1% total harmonic distortion is higher than 100 mV/sub pp/, with a 1.5-V supply. The filter consumes very low power (5-13 mW for f/sub c/=70 MHz) compared to conventional implementations (e.g., 120 mW for f/sub c/=100MHz ).     

InP D-HBT ICs for 40-Gb/s and higher bitrate lightwave transceivers

The combination of device speed (f/sub T/, f/sub max/ > 150 GHz) and breakdown voltage (V/sub bceo/ > 8 V) makes the double heterojunction bipolar InP-based transistor (D-HBT) an attractive technology to implement the most demanding analog functions of 40-Gb/s transceivers. This is illustrated by the performance of a number of analog circuits realized in an InP D-HBT technology with an 1.2- or 1.6-/spl mu/m-wide emitter finger: a low phase noise push-push voltage-controlled oscillator with -7-dBm output power at 146 GHz, a 40-GHz bandwidth and low-jitter 40-Gb/s limiting amplifier, a lumped 40-Gb/s limiting driver amplifier with 4.5-V/sub pp/ differential output swing, a distributed 40-Gb/s driver amplifier with 6-V/sub pp/ differential output swing, and a number of distributed preamplifiers with up to 1.3-THz gain-bandwidth product.     

0.5-V analog circuit techniques and their application in OTA and filter design

We present design techniques that make possible the operation of analog circuits with very low supply voltages, down to 0.5 V. We use operational transconductance amplifier (OTA) and filter design as a vehicle to introduce these techniques. Two OTAs, one with body inputs and the other with gate inputs, are designed. Biasing strategies to maintain common-mode voltages and attain maximum signal swing over process, voltage, and temperature are proposed. Prototype chips were fabricated in a 0.18-/spl mu/m CMOS process using standard 0.5-V V/sub T/ devices. The body-input OTA has a measured 52-dB DC gain, a 2.5-MHz gain-bandwidth, and consumes 110 /spl mu/W. The gate-input OTA has a measured 62-dB DC gain (with automatic gain-enhancement), a 10-MHz gain-bandwidth, and consumes 75 /spl mu/W. Design techniques for active-RC filters are also presented. Weak-inversion MOS varactors are proposed and modeled. These are used along with 0.5-V gate-input OTAs to design a fully integrated, 135-kHz fifth-order elliptic low-pass filter. The prototype chip in a 0.18-/spl mu/m CMOS process with V/sub T/ of 0.5-V also includes an on-chip phase-locked loop for tuning. The 1-mm/sup 2/ chip has a measured dynamic range of 57 dB and draws 2.2 mA from the 0.5-V supply.     

A 1.8-V 10-Gb/s fully integrated CMOS optical receiver analog front-end

A fully integrated 10-Gb/s optical receiver analog front-end (AFE) design that includes a transimpedance amplifier (TIA) and a limiting amplifier (LA) is demonstrated to require less chip area and is suitable for both low-cost and low-voltage applications. The AFE is fabricated using a 0.18-/spl mu/m CMOS technology. The tiny photo current received by the receiver AFE is amplified to a differential voltage swing of 400 mV/sub (pp)/. In order to avoid off-chip noise interference, the TIA and LA are dc-coupled on the chip instead of ac-coupled though a large external capacitor. The receiver front-end provides a conversion gain of up to 87 dB/spl Omega/ and -3dB bandwidth of 7.6 GHz. The measured sensitivity of the optical receiver is -12dBm at a bit-error rate of 10/sup -12/ with a 2/sup 31/-1 pseudorandom test pattern. Three-dimensional symmetric transformers are utilized in the AFE design for bandwidth enhancement. Operating under a 1.8-V supply, the power dissipation is 210 mW, and the chip size is 1028 /spl mu/m/spl times/1796 /spl mu/m.     

A high current drive CMOS output stage with a tunable quiescent current limiting circuit

A CMOS output stage based on a complementary common source with an original quiescent current limiting circuit is presented. The quiescent current can be varied over a wide range by means of a control current with no need to modify the transistor aspect ratios. The output stage has been coupled to a conventional complementary input stage to form a rail-to-rail buffer. A prototype with the inclusion of auxiliary pins for biasing and current monitoring purposes has been designed using the 1-/spl mu/m double-polysilicon BCD3S process of STMicroelectronics. On a single 5-V power supply, the maximum output current is 20 mA. The amplifier, biased for a total power dissipation of 1 mW, exhibits a total harmonic distortion of -58 dB at 1 kHz with 4-V peak-to-peak on a 330-/spl Omega/ load. Correct operation of the quiescent current limiting circuit has been demonstrated for a minimum supply voltage of 2.2 V.     

40-Gb/s circuits built from a 120-GHz f/sub T/ SiGe technology

Product designs for 40-Gb/s applications fabricated from SiGe BiCMOS technologies are now becoming available. In this paper we first briefly discuss heterojunction bipolar transistor (HBT) device operation at high speed, demonstrating that perceived concerns regarding lower BV/sub CEO/ and higher current densities required to operate silicon HBTs at such high speeds do not in actuality limit design or performance. The high-speed portions of the 40-Gb/s system are then addressed individually. We demonstrate the digital capability through a 4: 1 multiplexer and a 1 : 4 demultiplexer running over 50 Gb/s error free at a -3.3-V power supply. We also demonstrate a range of analog elements, including a lumped limiting amplifier which operates with a 35-GHz bandwidth, a transimpedance amplifier with 220-/spl Omega/ gain and 49.1-GHz bandwidth, a 21.5-GHz voltage-controlled oscillator with over -100-dBc/Hz phase noise at 1-MHz offset, and a modulator driver which runs a voltage swing twice the BV/sub CEO/ of the high-speed SiGe HBT. These parts demonstrate substantial results toward product offerings, on each of the critical high-speed elements of the 40-Gb/s system.     

High-gain SiGe transimpedance amplifier array for a 12/spl times/10 Gb/s parallel optical-fiber link

A transimpedance amplifier array for 12 parallel optical-fiber channels each operating at 10 Gb/s is presented, which is used in the receiver of short-distance links. It stands out for the following features: high gain (transimpedance 25 k/spl Omega/ in the limiting mode), high input sensitivity and wide input dynamic range (input current swing from 20 to 240 /spl mu/A/sub p-p/), constant output voltage swing (differential 0.5 V/sub p-p/ at 50 /spl Omega/ load), and low power consumption (1.4 W) at a single supply voltage (5 V). Each channel has its own offset-current control circuit. To the best of the authors' knowledge, the total throughput of 12/spl times/10 Gb/s=120 Gb/s is the highest value reported for a single-chip amplifier array. The target specifications have been achieved with the first technological run without needing any redesign. This fact demonstrates that the inherent severe crosstalk problems of such high-gain amplifier arrays can reliably be solved by applying adequate decoupling measures and simulation tools.     

Bipolar high-gain limiting amplifier IC for optical-fiber receivers operating up to 4 Gbit/s

A monolithic integrated high-gain limiting amplifier for future optical-fiber receivers is described. It is characterized by the following features: high insertion-voltage gain (maximum 54 dB); high input dynamic range (about 52 dB) at constant output-voltage swing (400 mV/SUB p-p/); high operating speed (up to at least 4 Gb/s); low power dissipation (350 mW at 50-/spl Omega/ load); standard supply voltage (5 V); 50-/spl Omega/ output buffer; one-chip solution; and small fabrication costs by use of a 2-/spl mu/m standard bipolar technology without needing polysilicon self-aligning processes. The good values of operating speed and power consumption, which the authors believe has until now not nearly been achieved by other comparable bipolar amplifier ICs, are a result of careful circuit design and optimization. The amplifier was extended to a high-sensitivity (amplitude and time) decision circuit operating at up to 4.0 Gb/s by adding a high-speed master-slave D-flip-flop IC fabricated with the same technology.     

CMOS video filters using switched capacitor 14 MHz circuits

In order to realize self-contained analog video LSI, video band switched-capacitor (C) filters, including a two-dimensional filter, have been experimentally fabricated. By using 2-/spl mu/m/spl middot/CMOS technology and high-speed/high-precision circuits, an LSI clock rate of 14 MHz, signal swing of 2 V p-p with a single 5-V supply, random noise S/N of 60-70 dB p-p/r.m.s at LSI output, and power dissipation of less than 5 mW per amplifier have been achieved. Single-stage cascode amplifiers are extensively used to attain video band speed. Neutralization is introduced into fully differential filters to improve their frequency response.     

A 1-V 140-/spl mu/W 88-dB audio sigma-delta modulator in 90-nm CMOS

A single-loop third-order switched-capacitor /spl Sigma/-/spl Delta/ modulator in 90-nm standard digital CMOS technology is presented. The design is intended to minimize the power consumption in a low-voltage environment. A load-compensated OTA with rail-to-rail output swing and gain enhancement is chosen in this design, which provides higher power efficiency than the two-stage OTA. To lower the power consumption further, class-AB operation is also adapted in the OTA design. Due to the relatively low threshold voltage of the advanced technology, no clock bootstrapping circuits are needed to drive the switches and the power consumption of the digital circuits is reduced. All the capacitors are implemented using multilayer metal-wall structure, which can provide high-density capacitance. The modulator achieves 88-dB dynamic range in 20-kHz signal bandwidth with an oversampling ratio of 100. The power consumption is 140 /spl mu/W under 1-V supply voltage and the chip core size is 0.18 mm/sup 2/.