Enhanced performance of a dye-sensitized solar cell with a modified poly(3,4-ethylenedioxythiophene)/TiO2/FTO counter electrode

ClO₄⁻-poly(3,4-ethylenedioxythiophene)/TiO₂/FTO (ClO₄⁻-PEDOT/TiO₂/FTO) counter electrode (CE) in dye-sensitized solar cells (DSSCs) is fabricated by using an electrochemical deposition method. Comparing with the DSSCs with ClO₄⁻-PEDOT/FTO counter electrode, the photocurrent-voltage (I-V) measurement reveals that the photocurrent conversion efficiency (η), fill factor (FF) and short-circuit current density (J_SC) of DSSCs with a ClO₄⁻-PEDOT/TiO₂/FTO CE increase. The enhanced performances of the DSSCs are attributed to the higher J_SC arising from the increase of active surface area of ClO₄⁻-PEDOT/TiO₂/FTO CE. Electrochemical impedance spectra (EIS) also indicate that the charge-transfer resistance on the ClO₄⁻-PEDOT/electrolyte interface decreases. Cyclic voltammetry results indicate that the ClO₄⁻-PEDOT/TiO₂/FTO electrode shows higher activity towards I₃⁻/I⁻ redox reaction than that of ClO₄⁻-PEDOT/FTO electrode.     

Electrochemical impedance spectroscopic investigation of CO2 reduction on polyaniline in methanol

The ac response of polyaniline thin films on platinum electrodes was measured at different dc potentials during the CO₂ reduction in methanol/LiClO₄ electrolyte with a small amount of 0.5 M H₂SO₄. The complex capacitance curves were simulated and the data obtained were used to calculate kinetic parameters, based on the assumption that the thermodynamic potential E₀ is in the region of −0.2-−0.1 V versus saturated calomel electrode (SCE). With E₀=−0.2 V versus SCE and β=0.6, a j₀ value of ca. 10⁻⁴ A cm⁻² was found for the electroreduction of CO₂ on the polyaniline electrode.     

Pitting corrosion studies on Al and Al-Zn alloys in SCN solutions

Pitting of Al and Al-6%Zn and Al-12%Zn alloys in KSCN solutions was studied by means of potentiodynamic anodic polarization, cyclic voltammetry, potentiostatic and impedance techniques. Measurements were conducted under different experimental conditions, complemented by ex situ scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDXA). The potentiodynamic anodic polarization curves do not exhibit active dissolution region due to spontaneous passivation. The passivity is due to the presence of thin film of Al₂O₃ on the anode surface (in case of Al) and the formation of ZnO on the Al₂O₃ matrix, in case of the two Al-Zn alloys (as evidenced from EDXA). The passive region is followed by pitting corrosion as a result of passivity breakdown by the aggressive attack of SCN⁻ anions. SEM images confirmed the existence of pits on the electrode surface. Alloyed Zn was found to enhance pitting attack. The pitting potential (E_pit) decreases with an increase in SCN⁻ concentration and temperature, but increases with increasing potential scan rate. The current/time transients show that the incubation time for passivity breakdown decreases with increasing applied positive potential, SCN⁻ concentration, and temperature. Impedance measurements showed that Nyquist plots are characterized by a depressed charge-transfer semicircle, the diameter of which is a function of SCN⁻ concentration, applied potential, solution temperature and sample composition.     

Iodide/triiodide electrochemistry in ionic liquids: Effect of viscosity on mass transport, voltammetry and scanning electrochemical microscopy

The electrochemistry of I⁻/I₃⁻ was studied in ionic liquids using a combination of cyclic voltammetry, chronoamperometry and scanning electrochemical microscopy (SECM). The electrolytes were 1-alkyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide [C_nC₁Im][Tf₂N], ionic liquids (where n = 2, 4 and 8) and I⁻ was typically added at a concentration of approximately 11 mM. During cyclic voltammetry, two sets of peaks were observed in each ionic liquid due to oxidation and reduction of the I⁻/I₃⁻ redox couple and oxidation/reduction of the I₃⁻/I₂ redox couple. The diffusion coefficients of I⁻ and I₃⁻, as determined using chronoamperometry, increased with increasing temperature and decreased with increasing ionic liquid viscosity. The effect of ionic liquid viscosity on ultramicroelectrode (UME) voltammetry was also determined using the I⁻/I₃⁻ redox couple. Steady-state behaviour was observed at 1.3 μm UMEs at slow voltammetric scan rates and steady-state SECM feedback approach curves were also obtained at a 1.3 μm Pt SECM tips, provided that the tip approach speed was sufficiently low.     

Lithium transport through a sol-gel derived LiMn2O4 film electrode: analyses of potentiostatic current transient and linear sweep voltammogram by Monte Carlo simulation

Lithium transport through a sol-gel derived LiMn₂O₄ film electrode was theoretically investigated by analyses of the potentiostatic current transient and the linear sweep voltammogram in consideration of the interactions between lithium ions by using Monte Carlo simulation. The anodic current transients experimentally measured on the film electrode ran with the slope of logarithmic current with logarithmic time flatter than −0.5 in the early stage, and then did in an upward concave shape in the time interval between t_T1 and t_T2. The linear sweep voltammograms experimentally measured on the film electrode showed two anodic peak currents I_p1 and I_p2 which increased linearly with scan rate v to the power of 0.66 and 0.70, respectively, (i.e. I_p1∝v^0.66 and I_p2∝v^0.70) at the scan rates higher than 0.5 mV s⁻¹. Moreover, the higher v was, the larger appeared the positive deviations of the first and second peak potentials E_p1 and E_p2 from the first and the second transition potentials E°_p1 and E°_p2, respectively, in the inverse derivative of the electrode potential curve. The current transients and the linear sweep voltammograms were analyzed in consideration of the interactions between lithium ions in the electrode by using the Monte Carlo simulation under two different constraints of the diffusion-controlled lithium transport and the cell-impedance-controlled lithium transport. The current transients and the linear sweep voltammograms, theoretically calculated under the cell-impedance-controlled constraint in consideration of the interactions between lithium ions, were in good agreement with the experimental results in shape. The disorder to order phase transition in the LiMn₂O₄ film electrode during the cell-impedance-controlled lithium transport at the potential jump and scan was discussed with the aid of the concentration profiles and the local cross-sectional snapshots of the configuration of lithium ions simulated by the Monte Carlo method.     

Preparation, characterization and electrocatalytic properties of an iodine|lignin-modified gold electrode

Hydrolytic lignin (HL) was adsorbed from an aqueous/organic solution on bare and iodine-modified gold electrode. Subsequent electrooxidation of the lignin adsorbate generated redox-active quinone-based groups in the biopolymer structure, exhibiting high reversibility during potential cycling and fast electron transfer kinetics. The presence of the chemisorbed iodine layer on the supporting gold electrode had a pronounced effect on the electrochemical properties of the final modified electrode in terms of double-layer capacitance (C_dl) and the observed surface coverage (Γ_obs). The high electrochemical activity in connection with low C_dl made it possible to apply the Au|I_(ads)|HL electrode as a fast-responding and sensitive electrochemical sensor for NADH. When tested in the amperometric mode at a constant potential of +0.4 V vs. Ag/AgCl, the modified electrode showed a linear current-concentration response over the range of 5-120 μM with a sensitivity of 2.39 nA μM⁻¹ cm⁻² and a detection limit of 1.0 μM (S/N = 3). Kinetic studies using the rotating disk electrode revealed that the mediated oxidation of NADH on the Au|I_(ads)|HL electrode was limited by the second order reaction of the analyte molecules with o-quinone moieties with a rate constant of ca. 4.7 × 10² M⁻¹ s⁻¹ (C_NADH → 0). The modified electrode showed high resistivity against fouling and retained ca. 65% activity after storage in phosphate buffer (pH 7.4) at room temperature for 1 week.     

Oxidation of iodide ions by means of cyclic voltammetry

From chronovoltammetric and cyclovoltammetric polarization curves three mechanisms of iodide ions have been established: 3I^? = I^?₃ + 2e,2I^?₃ = 3I₂ + 2e and 2I^? = I₂ + 2e under certain conditions of scan rate, concentration of iodide ions and area of electrode in the aqueous solutions KI (background solution 1 N Na₂SO₄) with half-wave potentials of 0.428, 0.489 and 0.507 V by silver/silver chloride electrode.     

Hydrogen evolution on RuxTi1−xO2 in 0.5 M H2SO4

Hydrogen evolution from 0.5 M H₂SO₄ on Ti electrodes coated with a Ru_xTi_1−xO₂ (x=0.04-0.5) layer has been studied by potentiostatic polarisation, cyclic voltammetry and ac-impedance spectroscopy. The results indicate that after a certain activation period the performance of such an electrode coating is comparable to platinum. The addition of small amounts of sodium molybdate increased the capacitance of the electrode and a reduction of the performance was observed. Increasing the temperature of the pure electrolyte from 20 to 75 °C caused an increase in the rate of the hydrogen evolution and in addition an increase of the electrode capacitance. The electrodes have been found to be rather tolerant to chloride and Fe²⁺ ions, and could hence be promising candidates as catalyst materials for solid polymer water electrolysis systems. From steady state measurements the Tafel slopes were found to change from −105 mV/decade for pure titanium to about −40 mV/decade for the (RuTi)O₂ coated electrodes. The exchange current densities were calculated from the steady state curves, as well as from impedance data, to be about 10⁻⁴ A cm⁻² after activation.     

Low temperature preparation of a high performance Pt/SWCNT counter electrode for flexible dye-sensitized solar cells

A platinum/single-wall carbon nanotube (Pt/SWCNT) film was sprayed onto a flexible indium-doped tin oxide coated polyethylene naphthalate (ITO/PEN) substrate to form a counter electrode for use in a flexible dye-sensitized solar cell using a vacuum thermal decomposition method at low temperature (120 °C). The obtained Pt/SWCNT electrode showed good chemical stability and light transmittance and had lower charge transfer resistance and higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction compared to the flexible Pt electrode or a commercial Pt/Ti electrode. The light-to-electric energy conversion efficiency of the flexible DSSC based on the Pt/SWCNT/ITO/PEN counter electrode and the TiO₂/Ti photoanode reached 5.96% under irradiation with a simulated solar light intensity of 100 mW cm⁻². The efficiency was increased by 25.74% compared to the flexible DSSC with an unmodified Pt counter electrode.     

Kinetics and mechanism of oxygen reduction at hydrous oxide film-covered platinum electrode in alkaline solution

This study uses rotating ring-disk electrode (RRDE) and linear sweep voltammetry (LSV) to characterize oxygen reduction kinetics in alkaline solution on platinum electrodes with various thickness of hydrous oxide (oxyhydroxy) film. Oxyhydroxy films are created on Pt electrodes by pretreatment in 1.0 mol dm⁻³ KOH at a constant voltage. The pretreatment voltage ranges from −1.2 to 1.0 V and is increased stepwise before each new experimental run to produce seven discreet films. LSV plots show oxyhydroxy film thickness strongly inhibits oxygen reduction and is inversely proportional to RRDE oxygen reduction current I_D for LSV voltages E_D from −0.1 to −0.46 V, but this trend reverses at E_D more negative than −0.46 V so that the worst-performing electrode becomes the best. However, this improvement disappears at around −0.8 V, suggesting this change involves a negatively charged ion, possibly embedded into the metal in the top few atomic layers either interstitially or substitutionally. The 1.0 V-pretreated electrode in the E_D range from −0.46 to −0.9 V of highest oxygen reduction current also exhibits the lowest hydrogen peroxide production, with zero H₂O₂ produced at −0.6 V, indicating the brief presence of the oxyhydroxy film on the Pt surface has strong lingering effects. The post-oxyhydroxy Pt surface is very different than the native Pt for oxygen reduction pathway and efficiency. Reaction order with respect to oxygen is close to 1. The rate constants of the direct O₂ to H₂O electroreduction reaction are increased with decreasing the potential from −0.2 to −0.6 V, but the O₂ to H₂O₂ electroreduction is contrary to this expectation. The rate constants of H₂O₂ decomposition on the oxyhydroxy film-covered Pt electrode are near constant around 1 × 10⁻⁴ cm s⁻¹ at E_D > −0.5 V.     

Detection of N-methyladenosine in urine samples by electrochemiluminescence using a heated ITO electrode

A sensitive and rapid electrochemiluminescence (ECL) method for the detection of N⁶-Methyladenosine (m6A) in urine samples on a heated indium-tin-oxide (ITO) electrode is presented. The ECL intensity of Tris(2,2′-bipyridyl) dichlororuthenium(II)hexahydrate (Ru(bpy)₃²⁺) can be enhanced by the presence of m6A. Experimental results showed that the change of ECL intensities (ΔI) of the Ru(bpy)₃²⁺ between before and after addition of m6A was affected by the working electrode surface temperature (T_e); the highest ΔI occurred at 31 °C. Under optimum conditions, the ΔI had a linear relationship with the m6A concentration in the range of 1.9 × 10⁻⁹-3.9 × 10⁻⁶ mol/L and a detection limit of 7.7 × 10⁻¹⁰ mol/L (S/N = 3) at T_e = 31 °C. The recovery of m6A standards added to urine samples verified the accuracy of the proposed method.     

Electrochemical study of tris(4-bromophenyl)amine and 2,2,6,6-tetramethylpiperidine-1-oxyl in room-temperature ionic liquids

The electrochemical behavior of tris(4-bromophenyl)amine (TBPA) and 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) was comparatively studied in room temperature ionic liquids (RTILs) containing 1-butyl-3-methylimidazolium cation [BMIm]⁺ and the anions BF₄⁻, PF₆⁻and CF₃SO₃⁻. TEMPO showed a well-defined electrochemical reversibility with anodic to cathodic peak current ratio (I_a/I_c) equals to unity in all RTILs, at a glassy carbon electrode. In contrast, I_a/I_c ratio greater than unity was observed at all scan rates employed (10-1000 mV s⁻¹) in cyclic voltammograms (CV) of TBPA in RTILs. Controlled-potential bulk electrolysis of TBPA in RTILs yielded a dark blue colored solution of monocation TBPA⁺, which is stable under nitrogen. Diffusion coefficient of TBPA⁺ cation was determined in all three ILs by chronoamperometry and found to be at least one order of magnitude less than the calculated value of TBPA. This effect, in conjunction with the deviation of the I_a/I_c ratio from unity could be ascribed to ion-pairing interaction between the TBPA⁺ cation and the anion of the RTILs.     

Study of reversible electrode processes with unsymmetrical cyclic reciprocal derivative chronopotentiometry

In this paper, the theoretical study of cyclic reciprocal derivative chronopotentiometry (CRDCP) for totally reversible electrode processes with symmetrical and unsymmetrical programmed currents is presented. The main viewpoints are: (1) for symmetrical programmed current, the amplitudes of the successive currents are the same, i.e. I(t) = (−1)ⁱ⁺¹I₀, whereas the transition times of each current step, τ_i, have different values. The properties of the dt/dE-E curves corresponding to each current cycle also differ a lot. (2) For unsymmetrical programmed current proposed in this work for the first time, the applied current successively reversed at each transition time steps to different amplitude. The use of this unique programmed current is advantageous versus symmetrical programmed current since the transition times obtained are equal to each other anticipatively, and the dt/dE-E curves also coincide with each other for the successive cycles. In this case, the results obtained in CRDCP are almost similar to those of cyclic voltammetry (CV). The characteristic parameters obtained in the dt/dE-E curves in both cases are quantitatively related to the species concentrations adjacent to the electrode surface and afford simple diagnosis criteria to characterize the reversibility of electrode processes. Properties of reversible electrode processes have also been further studied through the use of more than one current cycle.     

Effects of 1,3-dialkylimidazolium cations with different lengths of alkyl chains on the Pt electrode/electrolyte interface in dye-sensitized solar cells

The electrochemical behaviors of the tri-iodide (I₃⁻)/iodide (I⁻) redox couple of symmetric cells were investigated by cyclic voltammetry, steady-state polarization, chronocoulometry, and electrochemical impedance spectroscopy. 1,3-Dialkylimidazolium cations affected the characteristics of the Pt electrode/electrolyte interface by adsorbing on the Pt electrode, as a result of electrostatic interactions, and further affected the reduction of I₃⁻ on the Pt electrode. Capacitance of the double layers of the Pt electrode/electrolyte interface was chiefly determined by capacitance of the compact layer according to the Helmoholtz theory.     

Ionic conductivity, infrared and Raman spectroscopic studies of 1-methyl-3-propylimidazolium iodide ionic liquid with added iodine

Polyiodides (I_x⁻, x = 3 and 5) and 2I⁻…I₂ adducts were established from the Raman spectra study of 1-methyl-3-propylimidazolium iodide (MPIm⁺I_x⁻; 1 ≤ x ≤ 5) ionic liquids containing various amounts of iodine (0 mol ≤ I₂ ≤ 2 mol). The existence of I₃⁻ and 2I⁻…I₂ was established for 1 ≤ x ≤ 2.5, symmetric I₃⁻ ions for x = 3, while linear and discrete I₅⁻ was substantiated for 3 ≤ x ≤ 5. The presence of polyiodide species in MPIm⁺I_x⁻ (1 ≤ x ≤ 5) was correlated with an enhanced ionic conductivity, attributed to the established relay-type Grotthus mechanism. Two-step conductivity increase was also reflected in decrease of the hydrogen bond interactions between the CH ring groups and polyiodides. While in the concentration range 1 ≤ x ≤ 3 (triiodides and tetraiodides) IR bands changed only slightly in intensity, in the concentration range x > 3 the CH stretching bands (3040-3170 cm⁻¹) split and the new band at 1585 cm⁻¹ appeared in the IR spectra beside the already existing Im⁺ ring stretching mode at 1566 cm⁻¹.     

Electrochemical characterization of cetyltrimethyl ammonium bromide modified carbon paste electrode and the application in the immobilization of DNA

A cetyltrimethyl ammonium bromide modified carbon paste electrode (CTAB/CPE) was developed in this work based on the surface modification method. The improved electrochemical response of K₄Fe(CN)₆ at this electrode indicated that CTAB could change the surface property of carbon paste electrodes (CPEs), which was demonstrated by the electrochemical impedance spectroscopy (EIS). In 0.1 mM [Fe(CN)₆]^3−/4−, a low exchange current (i₀) of 2.72×10⁻⁷ A at bare CPE was observed while that at CTAB/CPE was 6.79×10⁻⁵ A. The effect of CTAB concentration on the electrode quality revealed that CTAB formed a compact monolayer on the electrode surface with high density of positive charges directed outside the electrode. This electrode showed strong accumulation ability toward Fe(CN)₆⁴⁻ and can also accumulate Co(phen)₃²⁺ by the adsorption of the organic ligands in the hydrophobic area of the monolayer. The electrode was applied to the immobilization of DNA, which was characterized by the isotherm adsorption of Co(phen)₃²⁺.     

Kinetics and mechanism of the electrochemical oxidation of nitrite ion dissolved as sodium nitrite in dimethylsulphoxide solutions on platinum electrodes

The kinetics of the electrochemical oxidation of NO₂⁻ ion dissolved in DMSO has been studied on Pt electrodes at temperature ranging from 25 to 44°C, by means of potentiostatic E/I curves and by relaxation techniques.     

Self-assembled monolayers-based immunosensor for detection of Escherichia coli using electrochemical impedance spectroscopy

An electrochemical impedance immunosensor for the detection of Escherichia coli was developed by immobilizing anti-E. coli antibodies at an Au electrode. The immobilization of antibodies at the Au electrode was carried out through a stable acyl amino ester intermediate generated by 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC) and N-hydrosuccinimide (NHS), which could condense antibodies reproducibly and densely on the self-assembled monolayer (SAM). The surface characteristics of the immunosensor before and after the binding reaction of antibodies with E. coli were characterized by atomic force microscopy (AFM). The immobilization of antibodies and the binding of E. coli cells to the electrode could increase the electro-transfer resistance, which was directly detected by electrochemical impedance spectroscopy (EIS) in the presence of Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ as a redox probe. A linear relationship between the electron-transfer resistance and the logarithmic value of E. coli concentration was found in the range of E. coli cells from 3.0 × 10³ to 3.0 × 10⁷ cfu mL⁻¹ with the detection limit of 1.0 × 10³ cfu mL⁻¹. With preconcentration and pre-enrichment steps, it was possible to detect E. coli concentration as low as 50 cfu/mL in river water samples.     

Decomposition of various endocrine-disrupting chemicals at boron-doped diamond electrode

Anodic decomposition of endocrine disrupting chemicals (EDCs) namely, 17β-estradiol (E2) and Bisphenol A (BPA) at boron-doped diamond (BDD) has been studied with a working solution volume of 250 ml under galvanostatic mode. Cyclic voltammetric experiments were performed to examine the redox response of E2 and BPA as a function of cycle number. Kinetic analysis suggests that electro-oxidation reaction of EDCs undergo the control of applied current density (I_appl). The mineralization behavior of EDCs was investigated at BDD anode monitoring the total organic carbon (TOC) value at three different I_appl. Electrolysis at high anodic potential causes complex oxidation of EDCs that lead to form the final sole product as CO₂. From these TOC results, the mineralization current efficiency was evaluated and discussed. In order to examine the effect of electrolyte variables on EDCs, BPA compound was taken and undergone the supporting medium and pH variation experiments. Considering global oxidation process, the effect of supporting medium (Na₂SO₄, NaNO₃, and NaCl) has been discussed in terms of electro-generated inorganic oxidants such as S₂O₈²⁻, H₂O₂ and ClO⁻. The better performance of BDD anode was proved on a comparative study with Pt and glassy carbon under similar experimental conditions. A possible reaction mechanism for BPA degradation involving three main aromatic intermediates, identified by GC-MS analysis, was proposed.     

Electrochemical behaviour of passive films on molybdenum-containing austenitic stainless steels in aqueous solutions

Passivation and its breakdown reactions have been studied on Mo-containing stainless steel specimens using different electrochemical techniques. Mo-containing stainless steel specimens were polarized in both naturally aerated NaCl and Na₂SO₄ solutions of different concentrations at 25 ± 0.2 °C between −1000 and 1500 mV versus saturated calomel electrode (SCE). The results of potentiodynamic polarization showed that i_corr and i_c increases with increasing either Cl⁻ or SO₄²⁻ concentration indicating the decrease in passivity of the formed film. EIS measurements under open circuit conditions confirmed that the passivity of the film decrease with increase in either Cl⁻ or SO₄²⁻ concentration.