Mechanical and tribological properties of vapour deposited low friction coatings on Ni plated substrates

Soft steel and aluminium substrates with load-carrying layers of electroplated nickel were coated with commercially available low friction vapour deposited coatings. The mechanical and tribological properties of the coating and substrate composites were evaluated with special emphasis on the influence of the nickel layer. Two different thicknesses of the intermediate load-carrying nickel layer were tested. The samples were evaluated regarding friction and sliding wear, abrasive wear, hardness and elastic modulus, morphology and coating thickness and adhesion between substrate and coating. It was found that all the evaluated low friction coatings were possible to be successfully deposited on the intermediate nickel layer. A relatively thick intermediate nickel layer is a promising candidate for improvement of the load-carrying capacity.     

Wear resistance and anti-sticking properties of duplex treated forming tool steel

The aim of this work was to investigate the potential of using hard physical vapour deposition (PVD) coatings on forming tools, as well as to determine the influence of plasma nitriding on the load-carrying capacity and wear resistance of coated tool surfaces. A load-scanning test rig was used for evaluation, where duplex treated cold work tool steel samples were loaded against soft austenitic stainless steel and hardened ball bearing steel, respectively. Four different coatings (TiN, TiB₂, TaC and DLC) and two substrate treatments (hardening and plasma nitriding in two different gas mixtures) were included.Plasma nitriding alone significantly improved the friction, wear, and anti-sticking properties of the tool steel. PVD coating, and especially PVD coating of nitrided tool steel further improved the performance. Therefore, from the point of view of tool life as well as work peace surface quality, the DLC coating with its excellent anti-sticking properties and sufficiently good wear resistance represent the best solution for forming tool applications of austenitic stainless steel.     

Effect of Surface Roughening of Substrate Steel on the Improvement of Delamination Strength and Tribological Behavior of Hydrogenated Amorphous Carbon Coating Under Lubricated Conditions

The adhesion strength of diamond-like carbon (DLC) coatings is an obstacle in efforts to improve the reliability of coated products. It is generally believed that the roughening of the substrate surface improves the adhesion between a substrate and coating. The effect of surface roughening of the substrate on the delamination strength of DLC coating and the tribological behavior under lubrication were studied. Five types of roughened substrates were prepared by a wet blast device with differing materials, shapes, and sizes of the shot particles. A hydrogenated DLC film was deposited using plasma-enhanced chemical vapor deposition on the roughened substrates. The tribological properties were investigated under air and lubrication with pure water or n-decane. It was found that the delamination strength of the DLC coating could be improved by roughening the substrate surface, especially by spherical particles. It was also found that slight polishing of either the DLC surface deposited on the rough substrate or the roughened substrate before deposition significantly reduced the wear of the counter surface. The remaining chemical element of alumina particles on the roughened surface affected the delamination strength of the DLC coating.     

Influence of layer thickness on hardness and scratch resistance of Si-DLC/CrN coatings

Abstract

Multifunctional coatings, widely used in tribological applications, have their properties strongly influenced by the interaction of the system coating/substrate. The use of multilayered coatings has been pointed out as a solution for the problem of high internal stresses that can be generated in coated systems, in particular in the case of soft substrates. In multilayered coatings, a decrease in the stress gradient between substrate and coating improves adhesion. Moreover, the thickness of the coating has shown a strong influence on the tribological behaviour of the coated system. This paper, through widely used and efficient techniques, seeks to assess the influence of the thickness of different layers (DLC and CrN) on the response of a multifunctional coating. Si rich DLC and CrN coatings with different thicknesses were deposited on a steel substrate (AISI 1020) by Plasma Enhanced Magnetron Sputtering (PECVD). Scanning electron microscopy (SEM) and Raman spectroscopy (RS) were used in order to characterize the chemical composition and microstructure of the coatings. Instrumented indentation and scratch test techniques were used to measure hardness, elastic modulus, and adhesion of each layer. Critical loads were determined by visual analysis, using SEM in conjunction with the curves obtained in the scratch tests. The evaluation of the effect of the thicknesses of the layers allowed an optimised design of the multifunctional coated systems with improved durability.     

High temperature wear resistance of (TiAl)N PVD coating on untreated and gas nitrided AISI H13 steel with different heat treatments

The wear resistance of a PVD (Ti_0.7Al_0.3)N coating deposited on an as-received and gas nitrided AISI H13 has been examined by using ball-on-disc tests at room temperature and at 600 °C. In order to determine the influence of a previous heat treatment on this type of steel on the wear resistance of the (Ti_0.7Al_0.3)N coating, two commercial heat treatments were employed which gave rise to the same substrate hardness. Surface microhardness measurements have been carried out to determine the load-carrying capacity of the coated systems. In general, the wear behavior was found to be independent of the nature of the heat treatment applied to the substrate prior to the nitriding process but strongly dependent on the testing temperature. At room temperature, there were small variations between the different systems tested, whereas at high temperatures, clear differences were found between them. At 600 °C, a typical temperature that could be achieved during the aluminum extrusion processes, the nitrided H13 steel/(Ti_0.7Al_0.3)N PVD duplex coating shows a satisfactory wear resistance compared to both the nitrided steel and the steel substrate only coated with (Ti_0.6Al_0.4)N, which exhibited the worst performance. The satisfactory wear resistance observed for the duplex coating system at high temperature is mainly a consequence of two different aspects. Firstly, its higher load-carrying capacity due to the existence of a hard nitrided layer, as well as its high H/E ratio. Both parameters allow the presence of higher elastic strains without the failure of the ceramic layer, which would normally occur in the case of TiAlN PVD coatings deposited directly on the AISI H13 steel. Secondly, the intrinsic characteristics of the coating, i.e. its chemical constitution, which allows the formation of a dense oxide mixture inside the wear track that impedes both its further oxidation and the deterioration of the mechanical properties as consequence of nitrogen diffusion.     

Investigation of mechanical and tribological properties of amorphous diamond-like carbon coatings

We investigated the mechanical and tribological properties of amorphous diamond-like carbon (DLC) coatings deposited on Si(100) by a pulsed bias deposition technique. Tribological studies were performed using a pin-on-disc (POD) apparatus under a normal load of 6.25 N and at 10% relative humidity, with a ruby pin as a slider. Hardness measurements were performed using a nanoindenter and apparent fracture toughness using indentation techniques. We studied the influence of residual stresses on apparent fracture toughness. The data revealed that the thickness, hardness and compressive stress of the coating play different roles in the apparent fracture toughness. Crack initiation is influenced by the thickness and hardness of the coating, whereas crack propagation is influenced by the compressive stress in the film. The apparent fracture toughness of DLC coatings increased with coating hardness.     

Characterization of DC magnetron sputtered diamond-like carbon (DLC) nano coating

Development in vapor deposition techniques over the last two decades has led to the introduction of many advanced coatings for metal-cutting tools. This paper examines the characteristics of multilayer Ti, TiN, and diamond-like carbon (DLC) coatings deposited on standard tool substrates at varying sputtering parameters and conditions, such as power density, partial pressure, substrate temperature, and reactive gases. The characteristics of films were examined using an X-ray diffractometer, Raman microscope, surface profilometer (to measure the thickness of the coating), Rockwell hardness tester (to test adhesion), and a micro hardness tester. The pin-on-disc test setup was used to find the coefficient of friction of the coatings. The results indicated that a graded multilayer coating showed better adhesion to the substrates. It was observed that higher target power density resulted in an increase of micro hardness and crystalline planes of coating. Lattice constant matching among layers of coating, proper substrate preparation, and a sequence of cleaning processes are the crucial factors for the enhancement of adhesion strength.     

Effect of hydrogenated DLC coating hardness on the tribological properties under water lubrication

Hydrogenated diamond-like carbon (DLC) coatings were deposited using unbalanced magnetron sputtering (UBM) equipment with different hardnesses. Effects of coating hardness on tribological properties were investigated with tribo-tests under water lubrication. Results showed that the wear volume increased rapidly during the initial running-in process, but remained nearly constant after the running-in process. The ball wear rate increased as the hardness of the DLC coating increased when metals (stainless steel and brass) were used as counter parts. In contrast, the UHMWPE ball wear rate was independent of the DLC hardness. TEM analysis and nano-indentation measurements were conducted of the transfer layer on the counter bodies’ contact surfaces. The transfer layer consisted mainly of Fe, O and C. The low friction of DLC coating is attributed to this low hardness transfer layer, which acts as a boundary-lubricating layer with low shear strength.     

超薄类金刚石膜纳米摩擦性能研究

使用原子力显微镜对由微波等离子体电子回旋共振化学气相沉积技术制备的超薄类金刚石薄膜的纳米摩擦性能进行了研究。结果表明：氢化非晶碳膜(a-C：H)的摩擦力和外加载荷基本成线性关系，可以使用修正的Amonton公式进行表征；厚度在64．9nm以下薄膜的微观承载性能和膜厚存在明显的正比例关系。通过分析磨损深度和循环次数之间的关系以及对磨损区域的导电性研究，表明a-C：H膜表层的微观承载性能较其内层相差很大，表面存在着一层软膜。     

Tribological Dependence of the High-Performance Ferrous-Based Coating on Different Coating Counterparts in Engine Oil

A ferrous-based coating with significant chromium was fabricated on aluminum alloy substrate using a plasma spray technique. The tribological performance of the as-fabricated ferrous-based coating sliding against different coatings including Cr, CrN, TiN, and diamond-like carbon (DLC) in an engine oil environment were comparatively studied. Results showed that the high hardness of the sprayed ferrous-based coating was achieved due to the dispersion strengthening effect of Cr₇C₃ phase embedded in the austenite matrix. The ferrous-based coating exhibited low friction coefficients when coupled with these four coating counterparts, which could be attributed to the boundary lubricating effect of engine oil. However, both friction and wear of the ferrous-based coating were different when sliding against these different coating counterparts, which might be closely related to the surface roughness, self-lubricating effect, and mechanical properties of the coupled coatings. Ferrous-based coating sliding against CrN and DLC coatings exhibited good tribological performance in engine oil. The best coating counterpart for the ferrous-based coating in an engine was DLC coating.     

Evaluation of erosive wear resistance of TiN coatings by a slurry jet impact test

In this paper, it is proposed to use a new type of solid particle impact test (slurry jet) to swiftly evaluate wear properties of thin, single layered or multilayered coatings. By the slurry jet, 1.2 μm alumina particles were impacted at high velocity perpendicular to thin PVD coatings of TiN deposited on high speed steel substrate materials under various substrate temperatures. Since the coatings have a much higher wear resistance than the substrate material, the wear rate increases significantly to the higher level of the HSS material when the coatings are penetrated. This is utilized in the quantification of the assessment of coating wear. A ranking of wear resistance and correlations to the coating surface hardness measured by nano-indentation tests, and coating morphology and structures are given and discussed. The TiN deposited under the highest substrate temperature proved to have the highest wear resistance although it had a relatively low hardness. The wear rate of the TiN coatings varies with the orientation of grains, that is, the {1 1 1} orientation that dominates for the high temperature deposition shows a higher wear resistance than the {1 0 0} orientation, which corresponds with the cleavage fracture behavior. Thus, it can be recommended as a screening test when evaluating coatings and coated materials.     

Substrate Effects on the Micro/Nanomechanical Properties of TiN Coatings

Nanoindentation and nanoscratch tests were performed for titanium nitride (TiN) coatings on different tool steel substrates to investigate the indentation/scratch induced deformation behavior of the coatings and the adhesion of the coating–substrate interfaces and their tribological property. In this work, TiN coatings with a thickness of about 500 nm were grown on GT35, 9Cr18 and 40CrNiMo steels using vacuum magnetic-filtering arc plasma deposition. In the nanoindentation tests, the hardness and modulus curves for TiN/GT35 reduced the slowest around the film thickness 500 nm with the increase of indentation depth, followed by TiN/9Cr18 and TiN/40CrNiMo. Improving adhesion properties of coating and substrate can decrease the differences of internal stress field. The scratch tests showed that the scratch response was controlled by plastic deformation in the substrate. The substrate plays an important role in determining the mechanical properties and wear resistance of such coatings. TiN/GT35 exhibited the best load-carrying capacity and scratch/wear resistance. As a consequence, GT35 is the best substrate for TiN coatings of the substrate materials tested.     

Effect of coating thickness on properties of Mo coatings deposited by plasma spraying

Plasma sprayed molybdenum coatings with different coating thicknesses (100, 200, 300 and 400 μm) were deposited on steel substrate. The variation in microstructural characteristics and properties of coatings with various thicknesses was investigated. The microhardness was measured using a Vickers’ indenter. The quantitative investigation of porosity is carried out with the help of computerised image analyser. The influence of coating thickness on wear resistance was estimated using pin on disc wear test rig. The worn surface of coated pin was characterised by scanning electron microscopy. The experimental results indicated that porosity of coating was increased with increased coating thickness. The enhanced coating thickness also resulted in decreasing microhardness and reduced wear resistance. In this study, the plasma sprayed thin coating with thickness of 100 μm possesses the lowest porosity, the highest hardness and better wear resistance.     

Friction and wear behaviour of hard and superhard coatings at cryogenic temperatures

The work presents data on friction and wear behaviour of pin-on-disc pairs with superhard diamond-like carbon (DLC) coatings and hard coatings of zirconium nitride (ZrN) and titanium nitride (TiN) in liquid nitrogen with loads of 2.5 and 10 N and sliding speed of 0.06 m/s. It is shown that at cryogenic temperatures the friction coefficients of pairs of two types of DLC coatings obtained by vacuum-arc deposition of filtered high-speed carbon plasma fluxes depend to a great deal on the mechanical properties of the coatings defined by predominant sp² or sp³ hybridization of valence electrons. A friction coefficient of 0.76 was observed for friction pairs of superhard (90 GPa) DLC coatings having properties similar to those of diamond. For “softer” DLC coatings of 40 GPa and properties similar to those of graphite the friction coefficient shows lower values (0.24–0.48) dependent on normal load and counterbody material. The DLC coatings obtained by the filtered arc technology exhibit good wear resistance and have strong adhesion to the substrate under friction in liquid nitrogen. With a normal load of 10 N under cryogenic temperature a low wear rate (of the order of 7.2×10⁻⁴ nm/cycle) was found for superhard DLC coatings. The friction coefficient of pairs with hard ZrN and superhard DLC coatings on steel discs was revealed to be linearly dependent on the counterbody material hardness between 20 and 100 GPa. The hardness of the pin was varied by means of depositing TiN or DLC coatings and also by using high-hardness compounds (boron nitride and synthetic diamond). Proceeding this way can be promising since it offers the possibility of creating low-temperature junctions of required friction properties.     

The influence of surface roughness on friction and wear of machine element coatings

The use of low friction coatings like amorphous carbon or metal-doped carbon coatings on machine elements is constantly increasing. Most often, a surface treatment, e.g. grinding and polishing or honing, is required for optimal performance of the coated machine element. This can be time consuming and costly.In this study, the effect of surface roughness on friction and sliding wear of two different coatings, one tungsten containing and one chromium containing coating, were examined using a ball-on-disc test. Ball bearing steel plates were grinded to different surface roughnesses and coated with the two different coatings.The friction was found to depend on surface roughness where the rougher surfaces gave higher friction coefficients. The wear rate for the a-C:W coating was found to be independent of the roughness, whereas the roughness had a strong influence on the wear rate for the a-C:Cr coating. This could partly be explained by a difference in wear mechanism, where fatigue wear was observed for the a-C:Cr coating but not for the a-C:W coating.     

TiN/Ti涂层在波箔轴承中的摩擦磨损性能

采用真空离子镀的方法在304不锈钢基体上喷涂厚度为3μm的TiN/Ti薄层,利用硬度计、三维形貌仪、划痕试验仪对涂层基本力学性能进行分析,通过球盘试验机分析涂层试样的摩擦磨损性能,根据波箔轴承性能测试实验台的测试结果:研究TiN/Ti涂层对基体表面耐磨减摩性能的影响。研究结果表明:TiN涂层硬度可达HV1 500,是基材硬度的5.5倍;TiN/Ti涂层平均摩擦因数为0.23,相对不锈钢304基材的平均摩擦因数0.71,降低了68%,磨损量也仅为基材的18.75%;GCr15与PTFE对磨的最大摩擦力矩可达2.4 N·mm,而TiN/Ti与PTFE对磨的最大摩擦力矩仅为1 N·mm,仅为GCr15的41.7%。TiN/Ti涂层表现出了优异的承载能力和耐磨减摩性能。     

Experimental study of mechanical properties and scratch resistance of ultra-thin diamond-like-carbon (DLC) coatings deposited on glass

To improve the mechanical and tribological properties of glass, an ultra-thin diamond-like-carbon (DLC) coating of 2.2 nm thick was deposited on the surface of glass, using the linear ion beam deposition technique. The coated glass showed significant improvement in scratch resistance against severe damage, such as cracking, delamination, and chipping. To understand the mechanism, an experimental study was carried out. It was found that the major contribution to the significantly improved scratch resistance attributable to the compressive stress, which was yielded during the deposition process and resides in the coating, as well as the top layer of glass substrate.     

Tribological Properties of DLC Coatings in Helium

The aim of this research work was to investigate tribological properties of low-friction DLC coatings when operating in helium atmosphere. Two commercial DLC coatings (a-C:H and Me-C:H) were included in the investigation and compared to reference PTFE-based coatings, normally used on components operating in helium. Coatings were deposited on hardened 100Cr6 bearing steel discs and tested against uncoated steel balls in low-load pin-on-disc contact configuration. Investigation was focused on the effect of substrate roughness (R _a ?=?0.05?C0.2???m) and contact conditions, including contact pressure (150?C350?MPa) and sliding speed (0.2?C0.4?m/s) on the coefficient of friction of DLC coatings operating in helium. Results of this investigation show that for low-load sliding contact DLC coatings provide low friction in helium atmosphere, similar to soft PTFE-based coatings. At the same time DLC coatings investigated were found to substantially reduce wear of the coated surface. However, while the wear of the coated part has been more or less eliminated, application of DLC coating prolongs running-in and increases wear of the steel counter-part. Furthermore, also in helium atmosphere tribolgical behaviour of DLC coatings showed dependence on the coating type and contact conditions.     

Residual stresses in TiN, DLC and MoS2 coated surfaces with regard to their tribological fracture behaviour

Thin hard coatings on components and tools are used increasingly due to the rapid development in deposition techniques, tribological performance and application skills. The residual stresses in a coated surface are crucial for its tribological performance. Compressive residual stresses in PVD deposited TiN and DLC coatings were measured to be in the range of 0.03-4 GPa on steel substrate and 0.1-1.3 GPa on silicon. MoS₂ coatings had tensional stresses in the range of 0.8-1.3 on steel and 0.16 GPa compressive stresses on silicon. The fracture pattern of coatings deposited on steel substrate were analysed both in bend testing and scratch testing. A micro-scale finite element method (FEM) modelling and stress simulation of a 2 μm TiN-coated steel surface was carried out and showed a reduction of the generated tensile buckling stresses in front of the sliding tip when compressive residual stresses of 1 GPa were included in the model. However, this reduction is not similarly observed in the scratch groove behind the tip, possibly due to sliding contact-induced stress relaxation. Scratch and bending tests allowed calculation of the fracture toughness of the three coated surfaces, based on both empirical crack pattern observations and FEM stress calculation, which resulted in highest values for TiN coating followed by MoS₂ and DLC coatings, being K_C = 4-11, about 2, and 1-2 MPa m^1/2, respectively. Higher compressive residual stresses in the coating and higher elastic modulus of the coating correlated to increased fracture toughness of the coated surface.     

Effect of substrate surface roughness on mechanical properties of diamond-like carbon coatings

Abstract

A plasma enhanced chemical vapour deposition (PECVD) amorphous carbon coating was deposited onto 100Cr6 steel substrates having varying degrees of surface roughness. The samples were subsequently evaluated to determine the correlation between substrate roughness and coating performance. The steel substrates were prepared before coating deposition to attain five different levels of roughness: (a) ground; (b) superfinished (SF); (c) polished to 1000 grit; (d) polished to 220 grit and (e) polished to a 1 μm diamond finish. The aim of the investigation was to determine the degree of finish required for good tribological performance and coating adhesion. The mechanical and tribological properties of the samples were assessed by nanoindentation, ramped load scratch testing, and pin on disk wear testing. Nanoindentation testing was used to determine the hardness of the samples and the relative contributions to the system hardness from the substrate and coating were separated using the model of Korsunsky et al. Nanoindentation testing showed that the coating hardness (when separated from the system hardness) was lower for the samples with the SF substrate than the others: the reasons for this are discussed in the light of Raman measurements on the fractions of diamond-like and graphite-like bonding in the coatings. Ramped load scratch testing was used to determine coating adhesion and the scratch test failure mode. With the exception of the samples with the ground substrate finish, studies of the friction coefficient plots during scratch testing showed little variation between the samples, and SEM imaging revealed a common failure mode of severe spallation at the scratch track border. The samples with the ground substrate showed differences in response between scratches parallel and perpendicular to the grinding direction, with scratches parallel to the grinding direction showing more severe spallation. The average critical load to failure, as determined by the point of first failure in the scanning electron microscope, was lower for the coatings on the SF substrate than the coatings on the 220 grit, 1000 grit and 1 micron finished substrates. The critical load to failure for the samples with ground substrates was lower than the other substrate surface finishes. Pin on disk wear testing of the samples against a steel ball revealed that the major effect of the varying substrate roughness was on the wear of the counterface, with rougher substrate finishes generally resulting in higher wear rates of the counterface, although the smoothest substrate finish, the micrometre finish, also resulted in higher wear. The sample whose substrate was superfinished gave least wear of the counterface and this was therefore the optimum finish for the samples when considering their performance in a tribological couple.