Effect of Pt on the water resistance of Co-zeolites upon the SCR of NOx with CH4

The objective of this work was to study the promotional effect of Pt on Co-zeolite (viz. mordenite, ferrierite, ZSM-5 and Y-zeolite) and Co/Al₂O₃ on the selective catalytic reduction (SCR) of NO_x with CH₄ under dry and wet reaction stream. After being reduced in H₂ at 350°C, the PtCo bimetallic zeolites showed higher NO to N₂ conversion and selectivity than the monometallic samples, as well as a combination of the latter samples such as mechanical mixtures or two-stage catalysts. After the same pretreatment, under wet reaction stream, the bimetallic samples were also more active. Among the other catalysts studied with 5% of water in the feed, (NO = CH₄ = 1000 ppm, O₂ = 2%), the NO conversion dropped to zero over Co_2.0Mor at 500°C and GHSV = 30,000 h⁻¹, whereas it is 20% in Pt_0.5Co_2.0Mor. In Pt/Co/Al₂O₃ the NO_x conversion dropped below 5% with only 2% of water under the same reaction conditions. The specific activity given as molecules of NO converted per total metal atom per second were 16.5 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Fer, 13 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Mor, 4.33 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0ZSM-5 and 0.5 × 10⁻⁴ s⁻¹ for Pt/Co/Al₂O₃. The Y-zeolite-based samples were inactive in both mono and bimetallic samples. The species initially present in the solid were Pt° and Co°, together with Co²⁺ and Pt²⁺ at exchange positions. Co° seems not to participate as an active site in the SCR of NO_x. Those species remained after the reaction but some reorganization occurred. A synergetic effect among the different species that enhances both the NO to NO₂ reaction, the activation of CH₄ and also the ability of the catalyst to adsorb NO, could be responsible for the high activity and selectivity of the bimetallic zeolites.     

Selective permeation and separation of steam from water–methanol–hydrogen gas mixtures through mordenite membrane

Separation properties of a mordenite membrane for water–methanol–hydrogen mixtures were studied in the temperature range from 423 to 523 K under pressurized conditions. The mordenite membrane was prepared on the outer surface of a porous alumina tubular support by a secondary-growth method. It was found that water was selectively permeated through the membrane. The separation factor of water/hydrogen and water/methanol were 49–156 and 73–101, respectively. Even when only hydrogen was fed at 0.5 MPa, its permeance was as low as 10⁻⁹ mol m⁻² s⁻¹ Pa⁻¹ up to 493 K, possibly suggesting that water pre-adsorbed in the micropores of mordenite hindered the permeation of hydrogen. The hydrogen permeance dramatically increased to 6.5 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ at 503 K and reached to 1.4 × 10⁻⁶ mol m⁻² s⁻¹ Pa⁻¹ at 523 K because of the formation of cracks in the membrane. However, the membrane was thermally stabilized in the presence of steam and/or methanol.     

Sorption kinetics of ammonia and ammonium ions on gel and macroporous sulphonic acid cation exchangers

Diffusion of ammonia and ammonium ions in sulphonic acid cation exchangers (gel Purolite SGC 100 × 10 MBH and macroporous Purolite C 160 MBH) from the solutions, representing the composition of “caustic condensate” (waste of nitrogen fertilizers production) is affected by pH of initial solution and structure of the matrix of cation exchanger. In gel matrix the effective intraparticle diffusivity (D_ef) depends greatly on the solution pH because of shrinkage in alkaline and swelling in acidic medium: on decreasing the initial concentration of ammonia from 0.214 to 0.003 and increasing that of ammonium nitrate from 0 to 0.214 mol l⁻¹ instead, the effect of ion exchange leads to a decrease in pH, resulting in swelling and increase in D_ef from 0.1 to 0.34 × 10⁻¹⁰ for gel Purolite SGC 100 × 10 MBH and variation of 0.18–0.11 × 10⁻¹⁰ m² s⁻¹ for macroporous Purolite C 160 MBH (resistant to shrinkage and swelling).

In Purolite C 160 MBH both macropore diffusivity (0.07–0.29 × 10⁻¹⁰ m² s⁻¹) and gel (solid phase) diffusivity (0.06–0.19 × 10⁻¹⁰ m² s⁻¹) are higher than micropore diffusivity (0.28–0.56 × 10⁻¹⁸ m² s⁻¹).

With respect to the effective intraparticle diffusivity, resistance to nitric acid, used for the regeneration, and high concentration of ammonium nitrate in eluate (up to 110 g l⁻¹), Purolite C 160 MBH has been installed for the conversion of ammonia and ammonium ions to ammonium nitrate reusable in the fertilizers production. This allows minimizing the economic loss and preventing the environmental contamination.     

On-stream modification of MFI zeolite membranes for enhancing hydrogen separation at high temperature

-Alumina-supported MFI zeolite membranes were modified by on-stream catalytic thermal cracking of methyldiethoxysilane (MDES) molecules inside the zeolitic channels during the separation of H₂/CO₂ gas mixture at 450 °C and atmospheric pressure. The MDES vapor was carried by the H₂/CO₂ feed gas and the effect of modification was monitored continuously through online analysis of the permeate stream. The modified membrane exhibited a significant increase in H₂ selectivity over CO₂ with a moderate decrease in H₂ permeance. At 450 °C, the modified MFI membrane obtained a H₂/CO₂ permselectivity of 17.5 with H₂ single gas permeance of 1.86 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ as compared to a permselectivity of 2.78 and permeance of 2.75 × 10⁻⁷ mol m⁻² s⁻¹ Pa⁻¹ for the membrane before modification. The modified membrane also showed good performance and stability in separation of H₂/CO₂ gas mixture containing up to 28.4% water vapor at 450 °C and atmospheric pressure.     

Cu based zeolites: A UV–vis study of the active site in the selective methane oxidation at low temperatures

An extensive series of 30 Cu exchanged zeolites and Cu impregnated silicas and aluminas have been tested in their capacities to stabilize the bis(μ-oxo)dicopper core. This core shows a remarkably activity towards methane, as it selectively hydroxylates methane into methanol at the low temperature of 125 °C. UV–vis spectroscopy is an easy approach to detect the presence of this bis(μ-oxo)dicopper core since it is characterized by an intense charge transfer band at 22 700 cm⁻¹. In this way it was found that after calcination, only the Cu exchanged zeolites ZSM-5 and MOR are capable of stabilizing this core. In addition, an optimum in the Si/Al ratio and in the calcination temperature were observed, indicating that this core requires a rather specific coordination environment. For ZSM-5, the optimal Si/Al ratio for bis(μ-oxo) dicopper core formation is between 12 and 30 and the amount of this core increases with increasing copper loading above Cu/Al = 0.2. Calcination in O₂ should be done at temperatures higher than 280 °C and lower than 700 °C. After reaction with methane at low temperature (150 °C), it was found that only Cu-ZSM-5 and Cu-MOR yielded methanol, whereas all the other Cu based materials yielded almost no methanol. At higher temperatures (200 °C) however, Cu-FER and Cu-BEA showed comparable methanol yields as Cu-ZSM-5 and also the methanol yield of Cu-MOR increased at this higher reaction temperature, indicating that a second not yet identified Cu-oxygen species is activated in the FER, BEA and MOR zeolites at higher temperatures.     

Catalytic decomposition of nitrous oxide over Ru-exchanged zeolites

We report that ultrastable faujasite-based ruthenium zeolites are highly active catalysts for N₂O decomposition at low temperature (120–200°C). The faujasite-based ruthenium catalysts showed activity for the decomposition of N₂O per Ru³⁺ cation equivalent to the ZSM-5 based ruthenium catalysts at much lower temperatures (TOF at 0.05 vol.-% N₂O: 5.132 × 10⁻⁴ s⁻¹ Ru⁻¹ of Ru-HNaUSY at 200°C versus 5.609 × 10⁻⁴ s⁻¹ Ru⁻¹ of Ru-NaZSM-5 at 300°C). The kinetics of decomposition of N₂O over a Ru-NaZSM-5 (Ru: 0.99 wt.-%), a Ru-HNaUSY (Ru: 1.45 wt.-%) and a Ru-free, Na-ZSM-5 catalyst were studied over the temperature range from 40 to 700°C using a temperature-programmed micro-reactor system. With partial pressures of N₂O and O₂ up to 0.5 vol.-% and 5 vol.-%, respectively, the decomposition rate data are represented by: −dN₂O/dt=itk(P_N2O) (P_O2)^−0.5 for Ru-HNaUSY, −dN₂O/dt=k(P_N2O) (P_O2)^−0.1 for Ru-NaZSM-5, and −dN₂O/dt=k(P_N2O)^−0.2 (P_O2)^−0.1 for Na-ZSM-5. Oxygen had a stronger inhibition effect on the Ru-HNaUSY catalyst than on Ru-NaZSM-5. The oxygen inhibition effect was more pronounced at low temperature than at high temperature. We propose that the negative effect of oxygen on the rate of N₂O decomposition over Ru-HNaUSY is stronger than Ru-NaZSM-5 because at the lower temperatures (<200°C) the desorption of oxygen is a rate-limiting step over the faujasite-based catalyst. The apparent activation energy for N₂O decomposition in the absence of oxygen is much lower on Ru-HNaUSY (E_a: 46 kJ mol⁻¹) than on Ru-NaZSM-5 (E_a: 220 kJ mol⁻¹).     

Liquid-phase methanol synthesis in apolar (squalane) and polar (tetraethylene glycol dimethylether) solvents

The kinetics of the three-phase methanol synthesis over a commercial Cu–Zn–Al₂O₃ catalyst were studied in an apolar solvent, squalane and a polar solvent, tetraethylene glycol dimethylether (TEGDME). Experimental conditions were varied as follows: P=3.0–5.3 MPa, T=488–533 K and Φ_vG/w=7.5×10⁻³–8×10⁻³ Nm³ s⁻¹kg⁻¹_cat. The nature of the slurry–liquid influences the activation energy and the kinetic rate constant by interaction between adsorbed species and solvent and by competitive adsorption of the solvent on the catalyst surface. The rate of reaction to methanol observed in TEGDME appeared to be about 10 times lower than in squalane. TEGDME reduces the reaction rate, which is a disadvantage for its use as a solvent.     

Influence of exchanged cations (Na, Cs, Sr and Ba) on xylene permeation through ZSM-5/SS tubular membranes

Na-ZSM-5 membranes were synthesized by secondary growth on the outer surface of stainless steel porous tubes. The membranes were ion-exchanged with Cs⁺, Ba²⁺ and Sr²⁺ to investigate their effect upon the separation of p-xylene from m-xylene and o-xylene. The permeation through the membranes was measured between 150 and 400 °C using each xylene isomer separately and a ternary mixture. All the membranes were selective to p-xylene in the temperature range studied. N₂ and xylene permeation measurements together with SEM observations were used to determine whether or not cracks and/or pinholes developed after exposure to the xylene isomers at high temperature (400 °C). Neither pore blockage nor extra-zeolitic pores developed after the ion exchange procedure and subsequent calcination. Furthermore, duplicate synthesized membranes of each cation form had similar separation factors and permeances. The duplicate values differ much less than the measurement error. The p-xylene permeation flux decreased in the order: Na-ZSM-5 > Ba-ZSM-5 > Sr-ZSM-5  Cs-ZSM-5 while the permeation flux of the m- and o-xylene decreased in the order Na-ZSM-5 > Sr-ZSM-5 > Ba-ZSM-5 > Cs-ZSM-5. The membrane that exhibited the best performance was Ba-ZSM-5, with a maximum p/o separation factor of 8.4 and a p-xylene permeance of 0.54 × 10⁻⁷ mol s⁻¹ m⁻² Pa⁻¹ at 400 °C.     

Reduction of nitrite by sulfamic acid and sodium azide from aqueous solutions treated by gliding arc discharge

Nitrous and nitric acids form in aqueous solutions exposed to a gliding arc discharge burning in humid air. The anions interfere when the concentration of particular solutes such as pollutants must be determined. In particular they falsify the COD measurements and spectral investigations and thus the efficiency of the plasma treatment in pollutant abatement. The nitrite anions must be thus removed, which require specific reagents. The influence of parameters such as solution pH and [reducers]/[NO₂⁻] ratio on the reduction reaction was evaluated. The reduction of nitrite into N₂ either by sulfamic acid or sodium azide is a first-order pH-dependant reaction with regard to nitrite and reducers (k₁ = 2.93 × 10⁻¹ m³ kmol⁻¹ s⁻¹; k₂ = 6.21 × 10⁻¹ m³ kmol⁻¹ s⁻¹, respectively). Sodium azide is thus more reactive than sulfamic acid.     

Temperature dependence of electrical and electromechanical properties of Pb(Mg1/3Nb2/3)O3–Pb(Ni1/3Nb2/3)O3–Pb(Zr,Ti)O3 thin films

The electrical and electromechanical properties of Pb(Mg_1/3Nb_2/3)O₃–Pb(Ni_1/3Nb_2/3)O₃–Pb(Zr,Ti)O₃ (PMN–PNN–PZT, PMN/PNN/PZT = 20/10/70) on Pt/Ti/SiO₂/Si substrates by chemical solution deposition was investigated. The PMN–PNN–PZT films annealed at 650 °C exhibited slim polarization hysteresis curves and a high dielectric constant of 2100 at room temperature. A broad dielectric maximum at approximately 140–170 °C was observed. The field-induced displacement was measured by scanning probe microscopy, the bipolar displacement was not hysteretic, and the effective piezoelectric coefficient (d₃₃) was 66 × 10⁻¹² m/V. The effective d₃₃ decreased with temperature, but the value at 100 °C remained 45 × 10⁻¹² m/V.     

The high strain rate compressive behaviour of polycarbonate and polyvinylidene difluoride

Measurements are presented of the compressive stress–strain behaviour of polycarbonate (PC) and polyvinylidene difluoride (PVDF) at strain rates from 10⁻⁴ to 10⁴ s⁻¹ at room temperature, and temperatures from −50 to +150 °C at 10³ s⁻¹. These results, obtained using a split Hopkinson pressure bar and Instron testing machine, are supported by dynamic mechanical analysis (DMA) measurements on the materials. Previous researchers have observed that the yield stress of these materials is bilinearly dependent on the logarithm of strain rate. The data presented here show that the bilinearity is due to the movement of low order transitions in the materials, so that they occur at temperatures above room temperature at the higher strain rates. In particular, these transitions are the β transition in PC, and the glass transition in PVDF. In addition, Appendix A presents measurements of a high strain rate Poisson's ratio of polycarbonate and its evolution with strain.     

Studies of Cu-ZSM-5 by X-ray absorption spectroscopy and its application for the oxidation of benzene to phenol by air

The oxidation of benzene to phenol has been successfully carried out in air over Cu-ZSM-5 at moderate temperatures. Several parameters such as Cu loading, calcination temperature and co-exchanged metal ions influence the nature of the catalyst. At low Cu loadings, the catalyst is more selective to phenol while at high Cu loadings CO₂ is the major product. In situ H₂-TPR XAFS studies reveal that at low Cu loadings, Cu exists as isolated pentacoordinated ions, with 4 equatorial oxygens at 1.94 Å and a more distant axial oxygen at 2.34 Å. At higher loadings, monomeric as well as dimeric Cu species exist, with a Cu–Cu distance of 2.92 Å. This suggests that the isolated Cu sites are the active sites responsible for phenol formation. When the catalyst was calcined at 450 °C, the activity peaked in the first hour and then slowly deactivated, but when the calcination temperature was increased to 850 °C, the activity slowly increased until it reached a plateau. Analysis of the XANES region during in situ H₂-TPR shows that at lower calcination temperatures two reduction peaks are present, corresponding to Cu²⁺ → Cu⁺ and Cu⁺ → Cu⁰. At high calcination temperatures, only a small fraction of the Cu undergoes the two-step reduction and most of the Cu remains in the +2 state. Slow deactivation of the catalyst calcined at 450 °C is due to migration of the Cu ions to inaccessible sites in the zeolite; at high calcination temperatures the Cu is tightly bound to the framework and is unable to migrate. EXAFS analysis of the sample calcined at 850 °C reveals two Cu–Si(Al) scattering paths at 2.83 Å. Doping the catalyst with other metals, in particular Ag and Pd, further improves the activity and selectivity of the reaction. The addition of water to the reaction increases the selectivity of the reaction by displacing the product from the active site.     

Pitting corrosion of Al and Al–Cu alloys by ClO4 ions in neutral sulphate solutions

The influence of various concentrations of NaClO₄, as a pitting corrosion agent, on the corrosion behaviour of pure Al, and two Al–Cu alloys, namely (Al + 2.5 wt% Cu) and (Al + 7 wt% Cu) alloys in 1.0 M Na₂SO₄ solution was investigated by potentiodynamic polarization and potentiostatic techniques at 25 °C. Measurements were conducted under the influence of various experimental conditions, complemented by ex situ energy dispersive X-ray (EDX) and scanning electron microscopy (SEM) examinations of the electrode surface. In free perchlorate sulphate solutions, for the three Al samples, the anodic polarization exhibits an active/passive transition. The active dissolution region involves an anodic peak (peak A) which is assigned to the formation of Al₂O₃ passive film on the electrode surface. The passive region extends up to 1500 mV with almost constant current density (j_pass) without exhibiting a critical breakdown potential or showing any evidence of pitting attack. For the three Al samples, addition of ClO₄⁻ ions to the sulphate solution stimulates their active anodic dissolution and tends to induce pitting corrosion within the oxide passive region. Pitting corrosion was confirmed by SEM examination of the electrode surface. The pitting potential decreases with increasing ClO₄⁻ ion concentration indicating a decrease in pitting corrosion resistance. The susceptibility of the three Al samples towards pitting corrosion decreases in the order: Al > (Al + 2.5 wt% Cu) alloy > (Al + 7 wt% Cu) alloy. Potentiostatic measurements showed that the rate of pitting initiation increases with increasing ClO₄⁻ ion concentration and applied step anodic potential, while it decreases with increasing %Cu in the Al samples. The inhibitive effect of SO₄²⁻ ions was also discussed.     

Pyrylium salt-photosensitised degradation of phenolic contaminants present in olive oil wastewaters with solar light: Part II. Benzoic acid derivatives

Solar light photodegradation, catalysed by a pyrylium salt, of seven benzoic acids present in olive oil mill, has been studied. Significant percentages of photodegradation (20–40%) have been achieved after 6 h of solar exposure for six of the acids, even though they were expected to be difficult to oxidise, due to the presence of an electron-withdrawing carboxylic acid group directly attached to the aromatic ring. Quenching constants for the electron-transfer process between the substrate and the excited catalyst were calculated by means of fluorescence measurements for syringic acid (66×10⁹ M⁻¹ s⁻¹), gallic acid (51×10⁹ M⁻¹ s⁻¹), veratric acid (51×10⁹ M⁻¹ s⁻¹), vanillic acid (48×10⁹ M⁻¹ s⁻¹), protocatechuic acid (37×10⁹ M⁻¹ s⁻¹) and p-hydroxybenzoic acid (15×10⁹ M⁻¹ s⁻¹); no quenching was found for benzoic acid. These photophysical measurements are in good correlation with the yields obtained in the pyrylium salt photocatalysed degradation of those phenolic acids.     

Impact of support oxide and Ba loading on the NOx storage properties of Pt/Ba/support catalysts: CO2 and H2O effects

A series of 1 wt.%Pt/_xBa/Support (Support = Al₂O₃, SiO₂, Al₂O₃-5.5 wt.%SiO₂ and Ce_0.7Zr_0.3O₂, x = 5–30 wt.% BaO) catalysts was investigated regarding the influence of the support oxide on Ba properties for the rapid NO_x trapping (100 s). Catalysts were treated at 700 °C under wet oxidizing atmosphere. The nature of the support oxide and the Ba loading influenced the Pt–Ba proximity, the Ba dispersion and then the surface basicity of the catalysts estimated by CO₂-TPD. At high temperature (400 °C) in the absence of CO₂ and H₂O, the NO_x storage capacity increased with the catalyst basicity: Pt/20Ba/Si < Pt/20Ba/Al5.5Si < Pt/10Ba/Al < Pt/5Ba/CeZr < Pt/30Ba/Al5.5Si < Pt/20Ba/Al < Pt/10BaCeZr. Addition of CO₂ decreased catalyst performances. The inhibiting effect of CO₂ on the NO_x uptake increased generally with both the catalyst basicity and the storage temperature. Water negatively affected the NO_x storage capacity, this effect being higher on alumina containing catalysts than on ceria–zirconia samples. When both CO₂ and H₂O were present in the inlet gas, a cumulative effect was observed at low temperatures (200 °C and 300 °C) whereas mainly CO₂ was responsible for the loss of NO_x storage capacity at 400 °C. Finally, under realistic conditions (H₂O and CO₂) the Pt/20Ba/Al5.5Si catalyst showed the best performances for the rapid NO_x uptake in the 200–400 °C temperature range. It resulted mainly from: (i) enhanced dispersions of platinum and barium on the alumina–silica support, (ii) a high Pt–Ba proximity and (iii) a low basicity of the catalyst which limits the CO₂ competition for the storage sites.     

Oxidative gas phase carbonylation of methanol to dimethyl carbonate over chloride-free Cu-impregnated zeolite Y catalysts at elevated pressure

Incipient wetness impregnation of zeolite Y with copper(II) nitrate solution and inert activation at 650 °C led to active catalysts for the oxidative carbonylation of methanol to dimethyl carbonate in the gas phase. Activities were measured under elevated pressure (0.4–1.6 MPa) with feed compositions of CO/MeOH/O₂ = 40/20/6–1.5 vol.% (balanced by N₂) over zeolite Y loaded with 10–17 wt.% copper. It could be shown that inert activation at 650 °C enhanced the activity, and that Cu loading of 14–17 wt.% gave the best performance. By combined XRD, TEM, TPR and DRIFT characterization it was found that the inert activation initiated dispersion of crystalline CuO, auto-reduction of Cu²⁺ to Cu⁺ and redistribution of copper ions with enrichment inside the supercages of the zeolite. The O₂ content of the feed was found to control the selectivity to dimethyl carbonate. Dimethyl carbonate selectivities of 70–75% were achieved within the temperature range of 140–170 °C at an O₂ content of 1.5 vol.%. This allowed space-time yields of dimethyl carbonate up to 632 g l_cat⁻¹ h⁻¹ at methanol conversions of 5–12%. Formation of the main side product, dimethoxymethane, was surprisingly affected by CO, which is not in line with suggested reaction pathways. A mechanism is proposed including formation of surface carbonate structures as common intermediate.     

Cloth catalysts for water denitrification: II. Removal of nitrates using Pd–Cu supported on glass fibers

The use of glass fibers in the form of woven cloth (GFC), as a new type of catalytic support, was studied for the reduction of aqueous nitrate solutions using a Pd/Cu–GFC catalyst. The activity (per gram Pd) and selectivity to nitrogen were found to be comparable with those found for Pd–Cu catalysts supported on the other carriers. The maximal initial removal activity was found for a catalyst with a Pd/(Pd+Cu) ratio of 0.81. The corresponding activity was 0.7 mmol min⁻¹ (g_Pd)⁻¹, and the selectivity was 97 mol% at 25°C and pH 6.5 for initial nitrate concentration of 100 mg l⁻¹. The selectivity to nitrogen declined at high conversions of nitrate and high pH.     

Dilute solution properties of carboxymethylchitins in high ionic-strength solvent

The hydrodynamic characteristics in aqueous solution at ionic strength I=0.2  of carboxymethylchitins of different degrees of chemical substitution have been determined. Experimental values varied over the following ranges: the translational diffusion coefficient (at 25.0°C), 1.1<10⁷×D<2.9 cm² s⁻¹; the sedimentation coefficient, 2.4<s<5.0 S; the Gralen coefficient (sedimentation concentration-dependence parameter), 130<k_s<680 mL g⁻¹; the intrinsic viscosity, 130<[η]<550 mL g⁻¹. Combination of s with D using the Svedberg equation yielded ‘sedimentation–diffusion' molecular weights in the range 40 000<M<240 000 g mol⁻¹. The corresponding Mark–Houwink–Kuhn–Sakurada (MHKS) relationships between the molecular weight and s, D and [η] were: [η]=5.58×10⁻³ M^0.94; D=1.87×10⁻⁴ M^−0.60; s=4.10×10⁻¹⁵ M^0.39. The equilibrium rigidity and hydrodynamic diameter of the carboxymethylchitin polymer chain is also investigated on the basis of wormlike coil theory without excluded volume effects. The significance of the Gralen k_s values for these substances is discussed.     

Catalyzing a cycloaddition with molecularly imprinted polymers obtained via immobilized templates

Polymeric catalysts to be applied in the Diels–Alder cycloaddition of hexachlorocyclopentadiene and maleic acid have been prepared via molecular imprinting with template molecules immobilized on silica particles. These enzyme mimicking polymers exhibit specific catalytic effects compared to non-imprinted control polymers or polymer-free solutions. It could be demonstrated that the activity of the molecularly imprinted material rises when increasing the temperature. By this means, the reduction of the activation energy (as expected for catalysts) from 63 to 55 kJ mol⁻¹ could be observed. Furthermore, the reaction was characterized based on the Michaelis–Menten model. For the diene compound a Michaelis constant of K_M=5.8 mmol l⁻¹ and an effective reaction rate of r_max,eff=0.4 μmol l⁻¹ s⁻¹, leading to a reaction rate constant k_eff=1.1×10⁻³ s⁻¹, were determined.     

Kinetics of Fischer–Tropsch synthesis on titania-supported cobalt

Rate data have been obtained for CO hydrogenation on a well-characterized 11.7% Co/TiO₂ catalyst in a differential fixed bed reactor at 20 atm, 180–240°C, and 5% conversion over a range of reactant partial pressures. The resulting kinetic parameters can be used to model precisely and accurately the kinetics of this reaction within this range of conditions. Turnover frequencies and rate constants determined from this study are in very good to excellent agreement with those obtained in previous studies of other cobalt catalysts, when the data are normalized to the same conditions of temperature and partial pressures of the reactants. Based on this comparison CO conversion and the partial pressure of product water apparently have little effect on specific rate per catalytic site. The data of this study are fitted fairly well by a simple power law expression of the form −r_CO=kP_H2^0.74P_CO^−0.24, where k=5.1×10⁻³ s⁻¹ at 200°C, P=10 atm, and H₂/CO=2/1; however, they are best fitted by a simple Langmuir–Hinshelwood (LH) rate form −r_CO=aP_H2^0.74P_CO/(1+bP_CO)² similar to that proposed by Yates and Satterfield.