共查询到20条相似文献,搜索用时 93 毫秒
1.
针对聚乙烯生产装置中介质为聚乙烯粉料的设备,介绍了氟树脂涂层设备在聚乙烯装置设备中的应用,讨论了氟树脂涂层设备的技术特性、结构、制造等特点,就氟树脂涂层的材料、涂层厚度的选择,喷涂工艺,检验项目和方法等进行了论述。并着重介绍了氟树脂涂层生产工艺过程中的若干工艺要点。 相似文献
2.
3.
4.
回收聚乙烯的应用领域越来越广泛,但不适用于海底管道防腐涂层。介绍了回收聚乙烯对管道三层聚乙烯涂层系统的危害,通过大量的实验以及涂层腐蚀评估,分析了其对管道防腐涂层性能的影响,提出在海底管道防腐涂层中应限制回收聚乙烯的使用。 相似文献
5.
介绍了滚塑技术、滚塑复合钢管的优点.阐述了交联型聚乙烯滚塑复合钢管、聚苯硫醚滚塑复合钢管、改性超高相对分子质量聚乙烯滚塑复合钢管的性能和特点. 相似文献
6.
钢管涂层过去是使用沥青、煤焦油、焦蚰磁漆、镀锌等涂装材料,但这类涂层的防腐性能差,钢管使用寿命短,为了延长钢管使用时间,国外在60年代初就使用环氧树脂粉末涂料和聚乙烯树脂粉末涂料,作为钢管涂层的防腐材料,大大提高了钢管的使用寿命。采用粉末涂层钢管还有如下特点: 相似文献
7.
氯磺化聚乙烯具有高的耐候性,而以其为基的屋顶涂层在炎热气候和工业腐蚀介质中则具有性能稳定性。在人工和自然环境下研究以氯磺化聚乙烯为基的屋顶涂层老化特点是有意义。以含有氯磺化聚乙烯(成膜基料)、 相似文献
8.
9.
改性聚乙烯在活塞式隔膜泵中的应用 总被引:1,自引:0,他引:1
系统地研究了聚乙烯的性能特征和成膜工艺,研制了改性PE涂膜,讨论了交联剂、助剂、颜填料对涂层性能的影响。应用结果表明改性后的聚乙烯完全符合防腐涂层的要求。 相似文献
10.
1 市场需要耐压管材
聚乙烯管材和钢管都是市场上传统的管材产品。
聚乙烯管道系统有许多优点,如:柔韧、耐腐蚀、容易连接并且连接可靠、质轻、在一定口径下可盘卷供应、适合不开挖铺设等。但是聚乙烯管道最显著的缺点是强度低,耐热性较差。 相似文献
11.
12.
本文通过聚乙烯本性改性、表面改性以及粘合剂的选择,探讨了聚乙烯与铝材的粘结,发现通过表面改性或/和使用热交、可以使铝材和聚乙烯达到优良的粘结,在实际上可获得应用。 相似文献
13.
介绍了交联聚乙烯的用途以及发展前景,概述了交联聚乙烯的生产技术,包括辐射交联、过氧化物交联、硅烷交联、紫外光交联、盐交联等交联方法,提出了发展我国交联聚乙烯生产的一些建议。 相似文献
14.
聚乙二醇及其衍生物催化合成苯并呋咱-N-氧化物的研究 总被引:1,自引:0,他引:1
研究了在聚乙二醇或其衍生物烷基聚氧乙烯醚、脂肪醇聚氧乙烯醚介质中,用NaOCl氧化邻硝基苯胺合成苯并呋咱-N-氧化物的反应过程,揭示了在合成反应中,聚乙二醇或其衍生物不仅可作为溶剂,还可替代碱金属氢氧化物,起到良好的催化作用。苯并呋咱-N-氧化物合成反应是以聚乙二醇或其衍生物为溶剂和催化剂,在邻硝基苯胺溶液中滴加理论用量1.1~1.5倍的次氯酸钠水溶液进行反应,合成温度为25~55 ℃,产物最高收率为98%。实验还表明,聚乙二醇及其衍生物稳定性好、次氯酸钠用量较小、反应温度适宜、时间短、条件缓和、产物收率和纯度高。 相似文献
15.
16.
《Journal of Adhesion Science and Technology》2013,27(9):869-882
The use of polyethylene gels to adhere high strength and high modulus polyethylene fibers together has been investigated. It was found that the joint strength obtained using high density polyethylene (HDPE) gel in decalin or tetralin depended on the heating temperature and time of the gel. When heated at 100°C for 30 min, the gel showed such a high joint strength that polyethylene fibers were torn, and this should be enough for practical uses. The results of the present study demonstrate that utilization of the polyethylene gel as an adhesive is an extremely effective method when polyethylene fibers are used in composite materials. 相似文献
17.
茂金属双峰聚乙烯的研究进展 总被引:2,自引:0,他引:2
概述了用复合茂金属催化体系法和工艺法制备双峰聚乙烯的研究进展,讨论了2组分比例,及聚合温度、聚合压力、氢气用量对茂金属双峰聚乙烯制备的影响规律。 相似文献
18.
综述了国内外双峰聚乙烯的生产方法、生产工艺及催化剂的研究开发进展,提出了发展我国双峰聚乙烯生产的一些建议。 相似文献
19.
In an attempt to produce surfaces that show low levels of adsorption of protein and adhesion of platelets, different molecular weights of polyethylene glycol methacrylate (PEG‐MA) were grafted onto polyethylene film by a preirradiation grafting process. The extent of grafting was found to be dependent on the storage condition of the irradiated polyethylene film, the preirradiated dose, reaction time and temperature, molecular weight of PEG‐MA, and the type of solvent. The grafting yield was found to decrease rapidly with storage time for irradiated polyethylene film stored at room temperature. On the other hand, the grafting yield in the irradiated polyethylene stored at −130°C remained nearly constant up to 20 days after irradiation. The grafting yield decreased with an increased PEG‐MA molecular weight. Human plasma protein was adsorbed onto control and PEG‐MA‐grafted polyethylene film surfaces, and the relative adsorbed amount of proteins on the surfaces was evaluated by electron spectroscopy for chemical analysis. The adsorbed protein and platelet adhesion on the polyethylene film surface decreased rapidly with the grafting yield. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 631–641, 1999 相似文献
20.
采用熔融纺丝法研究了低密度聚乙烯(PE-LD)、线形低密度聚乙烯(PE-LLD)和高密度聚乙烯(PE-HD)熔体的拉伸流变性能。结果表明,PE-LD、PE-LLD和PE-HD熔体的熔体强度都随温度的升高而下降;随着拉伸应变速率和温度的升高,PE-LD、PE-LLD和PE-HD熔体的拉伸黏度下降;随着挤出速率的提高,相同应变速率下,PE-LD、PE-LLD和PE-HD熔体的拉伸应力和拉伸黏度都有所降低。 相似文献