Application of Azido Esters as Energetic Plasticizers for LOVA Propellant Formulations

The study of a cyclotrimethylene trinitramine‐based low vulnerable ammunition (LOVA) propellant having cellulose acetate (CA) and nitrocellulose (NC) combinations as binders is described herein. Two propellant compositions ( 1 and 2 ) were prepared by replacing the non energetic plasticizer triacetin (TA) with the novel tetraazido ester plasticizers tetraazido malonate and tetraazido glutarate, respectively, and their ballistic, mechanical, and thermal properties were studied. Both compositions 1 and 2 showed thermal stability up to 200 °C with a heat release of 1752.81 and 1774.34 J g⁻¹, respectively. Both compositions have high impact insensitivity (h₅₀: 39 cm), friction insensitivity up to 36 kg, and an ignition temperature greater than 250 °C. The flame temperatures of 1 and 2 are 3164 and 3243 K with linear burn rate coefficients of 0.117 and 0.122 cm s⁻¹ MPa⁻¹, respectively. Similar percentage elongations at three different temperatures (−20 °C, +27 °C, and +55 °C) conditions were recorded for both compositions.     

Thermoplastic composites of polyamide‐12 reinforced by cellulose nanofibers with cationic surface modification

Cellulose nanofibers (CNFs) have many useful properties, including high strength and low thermal expansion, and are also environmentally friendly, readily renewable, safe, and biodegradable. The focus of this study was the development of lightweight thermoplastic polymer composites with good mechanical properties based on the incorporation of CNFs that have undergone surface pretreatment with a cationic reagent. The polyamide (PA12) was mixed with surface‐treated CNFs using a twin screw extruder and the resulting pellets were injection molded. The Izod impact strength without notch of CNF‐based composites exceeded that of composites incorporating organophilic montmorillonite (OMMT), a representative nanocomposite material. When the Izod impact test without notch, the impact hammer was stopped by the specimen with incorporation of surface treated CNF. Furthermore, the bending modulus and strength were equal to or greater than that of OMMT composites. The heat distortion temperature was improved as 33°C from neat PA12, and moreover improved as 29°C from OMMT composites. Cationic pretreatment of the CNF surfaces was found to increase the dispersion of the fibers and also to greatly improve the mechanical and thermal properties of the composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40920.     

Surface treatment of cellulose fibers with methylmethacrylate for enhanced properties of in situ polymerized PMMA/cellulose composites

Cellulose micro/nanofibers (CNF), prepared from jute fibers were surface treated with methyl methacrylate (MMA) for better dispersion into poly methyl methacrylate (PMMA) matrix. PMMA/cellulose composites were prepared by in situ suspension polymerization technique. The surface treatment of CNF was confirmed by Fourier transform infrared spectroscopy (FTIR) and Nuclear magnetic resonance (NMR) analysis. MMA‐treated cellulose micro/nanofibers (MCNF) demonstrated improved affinity and dispersion in MMA monomer as well as in the PMMA/cellulose composites. Thermal properties of the cellulose composites were analyzed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The glass transition temperature (T_g) of PMMA increased by nearly 19°C in the in situ cellulose composites compared to that of unreinforced PMMA as indicated by DSC. TGA showed increased thermal stability of the cellulose composites. Enhanced tensile properties as well as significantly lower moisture uptake were observed in the in situ prepared PMMA/cellulose composites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39808.     

Preparation and characterization of carbon nanofiber reinforced thermoplastic polyurethane nanocomposites

The effect of CNFs on hard and soft segments of TPU matrix was evaluated using Fourier transform infrared (FTIR) spectroscope. The dispersion and distribution of the CNFs in the TPU matrix were investigated through wide angle X‐ray diffraction (WAXD), field emission scanning electron microscope (FESEM), high resolution transmission electron microscope (HRTEM), polarizing optical microscope (POM), and atomic force microscope (AFM). The thermogravimetric analysis (TGA) showed that the inclusion of CNF improved the thermal stability of virgin TPU. The glass transition temperature (T_g), crystallization, and melting behaviors of the TPU matrix in the presence of dispersed CNF were observed by differential scanning calorimetry (DSC). The dynamic viscoelastic behavior of the nanocomposites was studied by dynamical mechanical thermal analysis (DMTA) and substantial improvement in storage modulus (E') was achieved with the addition of CNF to TPU matrix. The rheological behavior of TPU nanocomposites were tested by rubber processing analyzer (RPA) in dynamic frequency sweep and the storage modulus (G') of the nanocomposites was enhanced with increase in CNF loading. The dielectric properties of the nanocomposites exhibited significant improvement with incorporation of CNF. The TPU matrix exhibits remarkable improvement of mechanical properties with addition of CNF. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Electrospun carbon nanofiber web electrode: Supercapacitor behavior in various electrolytes

Carbon nanofibers (CNFs) draw great interest due to their noticeable mechanical, electrochemical, and physical properties. In this study, polyacrylonitrile‐based CNFs are obtained via electrospinning technique. Thermal oxidation and low temperature (950 °C) carbonization are applied to the electrospun web in order to achieve CNF. Through the process, Fourier transform infrared‐attenuated total reflectance spectroscopy and Raman spectroscopic results are investigated. The electrochemical properties of the self‐standing CNF webs are examined with electrochemical impedance spectroscopy and cyclic voltammetry. In addition, various electrolyte solutions are studied to investigate the capacitive behavior of CNF webs. Electrolyte type variation has a significant effect on the capacitance results and high capacitance values are achieved in aqueous solution. According to the differing electrolyte types, specific capacitance values (C_sp) are recorded between 204 and 149 F g^?1 where maximum specific capacitance is obtained in 0.5 M H₂SO₄ as 204 F g^?1. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45723.     

Poly(ϵ‐caprolactone)‐functionalized carbon nanofibers by surface‐initiated ring‐opening polymerization

Carbon nanofibers (CNFs) were covalently functionalized with biodegradable poly(?‐caprolactone) (PCL) by in situ ring‐opening polymerization (ROP) of ?‐caprolactone in the presence of stannous octoate. Surface oxidation treatment of the pristine CNFs afforded carboxylic CNFs (CNF‐COOH). Reaction of CNF‐COOH with excess thionyl chloride (SOCl₂) and glycol produced hydroxyl‐functionalized CNFs (CNF‐OH). Using CNF‐OH as macroinitiator, PCL was covalently grafted from the surfaces of CNFs by ROP, in either the presence or absence of sacrificial initiator, butanol. The grafted PCL content was achieved as high as 64.2 wt %, and can be controlled to some extent by adjusting the feed ratio of monomer to CNF‐OH. The resulting products were characterized by FTIR, NMR, Raman spectroscopy, TGA, DSC, SEM, TEM, HRTEM, and XRD. Core–shell nanostructures were observed under HRTEM for the PCL‐functionalized CNFs because of the thorough grafting. The PCL‐grafted CNFs showed different melting and crystallization behaviors from the mechanical mixture of PCL and CNF‐OH. This approach to PCL‐functionalized CNFs opens an avenue for the synthesis, modification, and application of CNF‐based nanomaterials and biomaterials. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Carbon nanoflake growth from carbon nanotubes by hot filament chemical vapor deposition

We report the growth of carbon nanoflakes (CNFs) on Si substrate by the hot filament chemical vapor deposition without the substrate bias or the catalyst. CNFs were grown using the single wall carbon nanotubes and the multiwall carbon nanotubes as the nucleation center, in the Ar-rich CH₄–H₂–Ar precursor gas mixture with 1% CH₄, at the chamber pressure and the substrate temperature of 7.5 Torr and 840 °C, respectively. In the H₂-rich condition, CNF synthesis failed due to severe etch-removal of carbon nanotubes (CNTs) while it was successful at the optimized Ar-rich condition. Other forms of carbon such as nano-diamond or mesoporous carbon failed to serve as the nucleation centers for the CNF growth. We proposed a mechanism of the CNF synthesis from the CNTs, which involved the initial unzipping of CNTs by atomic hydrogen and subsequent nucleation and growth of CNFs from the unzipped portion of the graphene layers.     

Effects of surface modification of carbon nanofibers on the mechanical properties of polyamide 1212 composites

In this study, the effects of carbon nanofiber (CNF) surface modification on mechanical properties of polyamide 1212 (PA1212)/CNFs composites were investigated. CNFs grafted with ethylenediamine (CNF‐g‐EDA), and CNFs grafted with polyethyleneimine (CNF‐g‐PEI) were prepared and characterized. The mechanical properties of the PA1212/CNFs composites were reinforced efficiently with addition of 0.3 wt % modified CNFs after drawing. The reinforcing effect of the drawn composites was investigated in terms of interfacial interaction, crystal orientation, crystallization properties and so on. After the surface modification of CNFs, the interfacial adhesion and dispersion of CNFs in PA1212 matrix were improved, especially for CNF‐g‐PEI. The improved interfacial adhesion and dispersion of CNFs in PA1212 matrix was beneficial to reinforcement of the composites. Compared with pure PA1212, improved degree of crystal orientation in the PA1212/CNF‐g‐PEI (CNF‐g‐EDA) composites was responsible for reinforcement of mechanical properties after drawing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41424.     

Effect of amine functionalization of CNF on electrical, thermal, and mechanical properties of epoxy/CNF composites

This paper presents experimental results of the effect of amine functionalization of carbon nanofibers (CNF) on the electrical, thermal, and mechanical properties of CNF/epoxy composites. The functionalized and non-functionalized CNFs (up to 3 wt%) were dispersed into epoxy using twin screw extruder. The specimens were characterized for electrical resistivities, thermal conductivity (K), UTS, and Vicker’s microhardness. The properties of the nanocomposites were compared with that of neat epoxy. The volume conductivity of the specimens increased by E12 S/cm and E09 S/cm in f-CNF/epoxy and CNF/epoxy, respectively, at 3 wt% filler loading. The increase in K for former was 106% at 150 °C, while for the latter it was only 64%. Similarly, UTS increased by 61% vs. 45% and hardness 65% vs. 43%. T _g increased with increase in filler content. SEM examinations showed that functionalization resulted in better dispersion of the nanofibers and hence greater improvement in the studied properties of the nanocomposites.     

Thermal behavior of poly(ethylene‐co‐propylene) containing carbon nanofibers

The effect of carbon nanofiber on the thermal behavior of poly(ethylene‐co‐propylene) (PEP) as revealed by differential scanning calorimetry and thermogravimetric analysis is reported. Analysis showed faster crystallization of PEP at higher temperature upon cooling with the increase of carbon nanofiber (CNF) content. The crystallization behavior changed to a single narrow crystallization peak as compared with the broad double crystallization peak of the neat polymer. This demonstrates the nucleation ability of CNF to induce crystals with more uniform distribution. The modified‐Avrami approach was used to study the crystallization behavior. We found that the crystallization rate constant increased with addition of CNFs. The dimensionality of crystal growth was found not to depend significantly on the content of CNF. Thermal degradation in air was monitored using thermogravimetric analysis and observed that the incorporation of nanofiber greater than 2.4 vol% improves thermal stability of PEP. All these results indicate that CNFs can significantly help polymer processing and increase thermal stability of polymers. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Thermal characterization of carbon‐nanofiber‐reinforced tetraglycidyl‐4,4′‐diaminodiphenylmethane/4,4′‐diaminodiphenylsulfone epoxy composites

The thermal properties of carbon nanofibers (CNF)/epoxy composites, composed of tetraglycidyl‐4,4′‐diaminodiphenylmethane (TGDDM) resin and 4,4′‐diaminodiphenylsulfone (DDS) as a curing agent, were investigated with differential scanning calorimetry (DSC), thermogravimetric analysis, and dynamic mechanical thermal analysis. DSC results showed that the presence of CNF had no pronounced influence on the heat of the cure reaction. However, the incorporation of CNF slightly improved the thermal stability of the epoxy. Furthermore, the storage modulus of the TGDDM/DDS epoxy was significantly enhanced, whereas the glass‐transition temperature was not significantly affected, upon the incorporation of CNFs. The storage modulus of 5 wt % CNF/epoxy composites at 25°C was increased by 35% in comparison with that of the pure epoxy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 295–298, 2006     

Novel in situ carbon nanofiber/polydimethylsiloxane nanocomposites: Synthesis,morphology, and physico‐mechanical properties

A series of carbon nanofiber (CNF)/polydimethylsiloxane (PDMS)‐based nanocomposites was prepared by anionic ring opening polymerization of octamethylcyclotetrasiloxane (D₄) in presence of pristine CNF and amine‐modified CNF. A detailed study of morphology–property relationship of the nanocomposites was carried out in order to understand the effect of chemical modification and loading of filler on property enhancement of the nanocomposites. An elaborate comparison of structure and properties was carried out for the nanocomposites prepared by in situ and conventional ex situ methods. Pronounced improvement in degree of dispersion of the fillers in the matrix on amine modification of CNFs was reflected in mechanical properties of the modified nanocomposites. Maximum upliftment in mechanical properties was observed for in situ prepared amine modified CNF/hydroxyl PDMS nanocomposites. For 8 phr filler loading, tensile strength increased by 370%, while tensile modulus showed an increase of 515% compared with the virgin elastomer. Furthermore, in situ prepared unmodified CNF/hydroxyl PDMS nanocomposites showed an increase of 141°C in temperature of maximum degradation (T_max) for 8 phr CNF loading. These results were correlated with the morphological analysis through transmission electron microscopic studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis,characterization, and properties of silylene–acetylene preceramic polymers

A series of silylene–acetylene preceramic polymers 3a–e were synthesized by polycondensation reaction of dilithioacetylene with dichlorosilane (H₂SiCl₂) or/and methyldichlorosilane (MeSiHCl₂). Their structures were confirmed by infrared spectra (IR), and ¹H and ²⁹Si NMR spectroscopies. Differential scanning calorimetry (DSC) diagrams show exotherms centered at 200 to 233°C temperature range, attributed to crosslinking reaction of the acetylene and Si? H groups. After thermal treatment, the obtained thermosets 4a–e possess excellent thermal stability. Thermogravimetric analysis (TGA) under nitrogen show the T_d5s (temperature of 5% weight loss) for all the thermosets are above 600°C, and the overall char yields are between 95.62% and 89.67% at 900°C. After pyrolysis at 1200°C, the obtained ceramic residues 5a–e exhibit good thermo‐oxidative stability with final weight retention between 98.76% and 91.66% at 900°C under air. In particular, perhydroploy(silylene)ethynylene 3a , which has the highest Si/C ratio in silylene–acetylene polymers, has the highest char yield, and the derived ceramic material 5a displays the best thermo‐oxidative stability. Based on Scanning electron microscopy and its associated energy‐dispersive X‐ray microanalysis (SEM EDX) and ¹³C magic angle spinning nuclear magnetic resonance (MAS NMR) analysis, ceramic 5a contains the highest SiC content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Long-term-durable anti-icing superhydrophobic composite coatings

We prepared carbon-based superhydrophobic composite coatings through a quick technique, merging multiwalled carbon nanotubes (MWCNTs) and carbon nanofibers (CNFs) to obtain hierarchical nanostructures on fiber-reinforced polymer (FRP) sheets; this was followed by supercritical fluid (SCF) processing and physical mixing (PM). The prepared SCF–MWCNT–CNF and PM–MWCNT–CNF composite coatings showed high water contact angles of 171.6 and 160°. The surface morphologies of the composite coatings revealed a lot of even nanostructures and folding at high magnifications. A high number of CNFs were added to the MWCNTs to initiate different nanoroughnesses in the composite coatings. The as-prepared superhydrophobic composite coatings showed excellent anti-icing properties, as indicated by the supercooled water droplet (-20°C) test under environmental conditions. Also, the surface of the SCF–MWCNT–CNF superhydrophobic composite coating showed excellent antifouling properties. We studied the surface wettability increasing different temperatures (30–180°C) in the SCF–MWCNT–CNF composite; this exposed the fact that the FRP sheets were thermally stable up to 100°C, and a while later, they changed from a superhydrophobic state to a superhydrophilic state at 180°C. This study revealed an economically workable method for the preparation of MWCNT–CNF composites with SCF techniques. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47059.     

A comparison of partially acetylated nanocellulose,nanocrystalline cellulose,and nanoclay as fillers for high‐performance polylactide nanocomposites

Partially acetylated cellulose nanofibers (CNF) were chemically extracted from sisal fibers and the performance of those CNF as nanofillers for polylactide (PLA) for food packaging applications was evaluated. Three PLA nanocomposites; PLA/CNF (cellulose nanofibers), PLA/CNC (nanocrystalline cellulose), and PLA/C30B (Cloisite^TM 30B, an organically modified montmorillonite clay) were prepared and their properties were evaluated. It was found that CNF reinforced composites showed a larger decrease on oxygen transmission rate (OTR) than the clay‐based composites; (PLA/CNF 1% nanocomposite showed a 63% of reduction at 23°C and 50% RH while PLA/C30B 1% showed a 26% decrease) and similar behavior on terms of water vapor barrier properties with 46 and 43%, respectively of decrease on water vapor transmission rate at 23°C and 50% RH (relative humidity). In terms of mechanical and thermomechanical properties, CNF‐based nanocomposites showed better performance than clay‐based composites without affecting significantly the optical transparency. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43257.     

Thermal behavior of graft copolymers of cotton cellulose and acrylate monomers

Cotton cellulose yarn was grafted with methyl acrylate, ethyl acrylate, n-butyl acrylate, and methyl methacrylate at various percentages of grafting. The effects of concentration of the initiator, concentration of the acid, and of temperature on grafting was studied and the mechanism discussed. The effect of reactivity of the monomer on the percentage graft-on is pointed out. Thermal behavior of natural and grafted cotton yarn was studied using dynamic thermogravimetry in air at a heating rate of 6°C/min up to a temperature of 500°C. The thermal stabilities of the samples grafted with various acrylate monomers to various percentages of grafting were computed from their primary thermograms by calculating the values of IDT, IPDT, and E^*. The results show that the thermal stability increases with increase in graft-on per cent, and the thermal stabilities of natural cotton and cotton grafted with different monomers are in the order ethyl > methyl > natural cellulose > methyl methacrylate > n-butyl acrylate.     

Biomimetic synthesis and characterization of carbon nanofiber/hydroxyapatite composite scaffolds

Three dimensional electrospun carbon nanofiber (CNF)/hydroxyapatite (HAp) composites were biomimetically synthesized in simulated body fluid (SBF). The CNFs with diameter of ∼250 nm were first fabricated from electrospun polyacrylonitrile precursor nanofibers by stabilization at 280 °C for 2 h, followed by carbonization at 1200 °C. The morphology, structure and water contact angle (WCA) of the CNFs and CNF/HAp composites were characterized. The pristine CNFs were hydrophobic with a WCA of 139.6°, resulting in the HAp growth only on the very outer layer fibers of the CNF mat. Treatment in NaOH aq. solutions introduced carboxylic groups onto the CNFs surfaces, and hence making the CNFs hydrophilic. In the SBF, the surface activated CNFs bonded with Ca²⁺ to form nuclei, which then easily induced the growth of HAp crystals on the CNFs throughout the CNF mat. The fracture strength of the CNF/HAp composite with a CNF content of 41.3% reached 67.3 MPa. Such CNF/HAp composites with strong interfacial bondings and high mechanical strength can be potentially useful in the field of bone tissue engineering.     

Preparation and characterization of polychloroprene nanocomposites with cellulose nanofibers from oil palm empty fruit bunches as a nanofiller

Cellulose nanofibers (CNFs) from oil palm empty fruit bunches were chemically modified by acetylation with acetic anhydride and pyridine (as the solvent and catalyst). The acetylated CNFs showed good dispersion in a polychloroprene (PCR) matrix. The tensile strength and modulus of neat PCR were improved, whereas its elongation at break decreased with increasing nanofiber content. Above the glass‐transition temperature (T_g), the dynamic mechanical analysis profiles showed that the storage modulus of the PCR–cellulose nanocomposites was higher than that of neat PCR. Meanwhile, the thermal stability was still maintained, and the T_g was close to the neat PCR at the 5 wt % addition level of CNFs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40159.     

Synthesis and electro‐optic properties of novel polyurethane containing the nitrophenylazoresorcinoxy group

A novel Y‐type polyurethane (polyurethane 3) containing 4‐(4‐nitrophenylazo)resorcinoxy groups as nonlinear optical (NLO) chromophores, which constitute part of the polymer backbone, was prepared and characterized. Polyurethane 3 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It shows thermal stability up to 270 °C from thermogravimetric analysis with a glass transition temperature obtained from differential scanning calorimetry of 102 °C. The second harmonic generation (SHG) coefficient (d₃₃) of the poled polymer film at 1064 nm fundamental wavelength is 2.06 pm V^?1. Polymer 3 exhibits thermal stability up to T_g, and no significant SHG decay is observed below 100 °C, which is acceptable for nonlinear optical device applications. Copyright © 2012 Society of Chemical Industry     

Novel thermally resistant polysilphenylenesiloxanes with a high content of vinyl substituents

Polysilphenylenesiloxanes containing various amounts of vinyl substituents (ranging from partial (25 %) to complete (100 %)) on the silicon atoms were synthesized. ²⁹Si NMR spectroscopy revealed that they had a well defined structure, as designed. Unlike the known crystalline poly(tetramethyl‐p‐silphenylenesiloxane), all polymers containing vinyl side groups were amorphous and showed low T_gs, ranging from ?52 to ?32 °C (from differential scanning calorimetry (DSC)). Dynamic and isothermal thermogravimetric (TG) analyses indicated that they all possessed a greatly improved thermal stability up to 500 °C, and have ultra‐high residual yields at 1000 °C under both inert and oxidative conditions. Polysilphenylenesiloxanes containing a high percentage of vulcanizable vinyl substituents should be excellent candidates for high‐temperature polymers and have potential applications such as heat‐resistant or flame‐retardant materials. Copyright © 2004 Society of Chemical Industry