Characteristics of poly(ether ether ketone) microporous membranes prepared via thermally induced phase separation (TIPS)

The morphology and bulk properties of microporous membranes based on poly (ether ether ketone) (PEEK) have been investigated as a function of initial casting composition and thermal and mechanical processing history. Membranes were prepared via solid—liquid phase separation of miscible blends of PEEK and polyetherimide (PEI), with subsequent extraction of the PEI diluent. Scanning electron microscopy studies revealed a microporous morphology with two distinct pore size scales corresponding to diluent extraction from interfibrillar and interspherulitic regions, respectively. The membrane structure was sensitive to both initial blend composition and crystallization temperature, with the resulting pore size distribution reflecting the kinetics of phase separation. For membranes prepared with lower initial diluent content or at lower crystallization temperatures, mercury intrusion porosimetry indicated a relatively narrow distribution of fine interfibrillar pores, with an average pore size of approximately 0.04 microns. Membranes prepared at higher diluent content or at higher crystallization temperatures displayed a broad pore distribution, with a sizeable population of coarse, interspherulitic pores (0.1 to 1 μm in size). Uniaxial drawing led to a fibrillated network structure with markedly higher water flux characteristics compared to the as-cast membranes. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2347–2355, 1997     

Hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK)

A procedure for obtaining high performance large internal diameter (ID; >1 mm) hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK) is presented. A simple mixture of isomers of diphenylphthalate is a good solvent for employing the thermal‐phase inversion process to obtain PEEK membranes. Obtaining large ID hollow fibers with substantial transmembrane flux requires sufficient melt strength during spinning to prevent excessive draw of the extruding fiber. The use of a second leachable polymer to the blend satisfies the conditions, and polysulphone (PS) is found to provide superior membranes relative to either poly(etherimide) (PEI) or poly(ether sulphone) (PES) as a second polymer. PEEK membranes obtained by this process yield better chemical resistance to a concentrated warm surfactant/oil solution. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 175–181, 1999     

Micro‐ and ultrafiltration film membranes from poly(ether ether ketone) (PEEK)

Film membranes from the thermoplastic poly(ether ether ketone) (PEEK) have been extruded and tested for their microfiltration and ultrafiltration performance. High‐performance asymmetric membranes have been obtained by extruding polymer blends of PEEK, polysulphone, and a small molecule solvent mixture, and then by removing the polysulphone and solvent in a subsequent extraction step. The process for making ultrafiltration membranes differs from microfiltration membranes only in the relative blend components, and the temperature of the film pick‐up rolls. Processing parameters with important effects on the membrane performance have been identified. Microfiltration membranes are characterized by their pore‐size distributions and SEM, and ultrafiltration membranes by their rejection of bovine serum albumin, bubble point, and SEM. Composite membrane for nanofiltration utilizing the PEEK ultrafiltration membrane as a substrate performed similarly to a commercial membrane for the same purpose. This work details the best method for making PEEK film membranes published to date. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1146–1155, 1999     

Crystal structure and drawing‐induced polymorphism in poly(aryl ether ether ketone). IV

A new crystal modification induced by strain and denoted as form II exists alongside the dominant form I structure in the uniaxially oriented poly(ether ether ketone) (PEEK) and the related polymers. The crystal structure of form II for PEEK is also found to possess a two‐chain orthorhombic packing with unit cell parameters of a equal to 0.475 nm, b equal to 1.060 nm, and c equal to 1.086 nm. More extended and flattened chain conformation of form II relative to that of form I is expected to account for an 8% increase in c‐axis dimension, which is attributed to the extensional deformation fixed in situ through strain‐induced crystallization during uniaxial drawing. Annealing experiments suggest that form II is thermodynamically metastable and can be transformed into more stable form I by chain relaxation and reorganization at elevated temperature without external tension. This strain‐induced polymorphism exists universally in the poly(aryl ether ketone) family. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 237–243, 1999     

Crystallization and melting behavior of poly(ether ether ketone)/poly(aryl ether sulfone) blends

The crystallization and melting behavior of poly(ether ether ketone) (PEEK) in blends with poly(aryl ether sulfone) (PES) prepared by melt mixing are investigated by differential scanning calorimetry (DSC) and wide‐angle X‐ray scattering (WAXS). The presence of PES is found to have a notable influence on the crystallization behavior of PEEK, especially when present in low concentrations in the PEEK/PES blends. The PEEK crystallization kinetics is retarded in the presence of PES from the melt and in the rubbery state. An analysis of the melt crystallization exotherm shows a slower rate of nucleation and a wider crystallite size distribution of PEEK in the presence of PES, except at low concentrations of PES, where, because of higher miscibility and the tendency of PES to form ordered structures under suitable conditions, a significantly opposite result is observed. The cold crystallization temperature of the blends at low PES concentration is higher then that of pure PEEK, whereas at a higher PES concentration little change is observed. In addition, the decrease in heat of cold crystallization and melting, which is more prevalent in PEEK‐rich compositions than in pure PEEK, shows the reduction in the degree of crystallinity because of the dilution effect of PES. Isothermal cold crystallization studies show that the cold crystallization from the amorphous glass occurs in two stages, corresponding to the mobilization of the PEEK‐rich and PES‐rich phases. The slower rate of crystallization of the PEEK‐rich phase, even in compositions where a pure PEEK phase is observed, indicates that the presence of the immobile PES‐rich phase has a constraining influence on the crystallization of the PEEK‐rich phase, possibly because of the distribution of individual PEEK chains across the two phases. The various crystallization parameters obtained from WAXS analysis show that the basic crystal structure of PEEK remains unaffected in the blend. Further, the slight melting point depression of PEEK at low concentrations of PES, apart from several other morphological reasons, may be due to some specific interactions between the component homopolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2906–2918, 2003     

聚醚醚酮纤维的发展现状与应用

综述了国内外聚醚醚酮(PEEK)纤维的研究发展现状;分析了制约我国PEEK纤维发展的原因;介绍了PEEK树脂的流变性能、纺丝技术;阐述了PEEK纤维的结构、物理化学性能及应用领域;提出我国应加大PEEK原料及其纤维的研发,实现PEEK纤维国产化。     

聚苯酯对聚醚醚酮结晶行为的影响

用模压法制备了聚苯酯(Ekonol)／聚醚醚酮(PEEK)复合材料，通过X射线衍射(XRD)、差示扫描量热分析(DSC)考察了PEEK的结晶行为，并测定了复合材料的熔点、结晶温度和玻璃化转变温度。结果表明：Ekonol含量的大小对PEEK的结晶行为产生了直接影响，PEEK的相对结晶度随着Ekonol含量的增加而提高；Ekonol含量小于30％时，对复合材料的熔点、结晶温度和玻璃化转变温度影响不大，但含量大于30％时，材料的结晶温度、熔融温度下降，玻璃化转变温度提高。     

Investigation on the crystallization behavior of poly(ether ether ketone)/poly(phenylene sulfide) blends

The morphology of nonisothermally crystallized poly(phenylene sulfide) (PPS) and its blend with poly (ether ether ketone) (PEEK) have been observed by polarized optical microscope (POM) equipped with a hot stage. The nonisothermal crystallization behavior of PPS and PEEK/PPS blend has also been investigated by differential scanning calorimetry (DSC). The maximum crystallization temperature for PEEK/PPS blend is about 15°C higher than that of neat PPS, and the crystallization rate, characterized by half crystallization time, of the PEEK/PPS blend is also higher than that of the neat PPS. These results indicate that the PEEK acts as an effective nucleation agent and greatly accelerates the crystallization rate of PPS. The Ozawa model was used to analyze the nonisothermal crystallization kinetics of PPS and its blends. The Avrami exponent values of neat PPS are higher than that of its blend, which shows that the presence of PEEK changed the nucleation type of PPS from homogeneous nucleation to heterogeneous nucleation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Isothermal crystallization behavior of nano-alumina particles-filled poly(ether ether ketone) composites

The isothermal crystallization behavior of nano-alumina particle-filled poly(ether ether ketone) (PEEK) composites has been investigated using differential scanning calorimeter. The results show that all the neat PEEK and nano-alumina-filled PEEK composites exhibit the double-melting behavior under isothermal crystallization. The peak crystallization times (τ_p) for all the neat PEEK and PEEK/aluminum oxide (Al₂O₃) composites increase with increasing crystallization temperature. Moreover, the crystallinity of the PEEK/Al₂O₃ composite with 7.5 wt % nano-filler content reached the maximum value of 44.8% at 290°C, higher than that of the neat PEEK polymer. From the lower value in τ_p and higher value in X_c for the PEEK/Al₂O₃ composites, the inclusion of the nano-alumina into the PEEK matrix favored the occurrence of heterogeneous nucleation. The Avrami exponents n of all the neat PEEK and PEEK/Al₂O₃ composites ranged from 2 to 3, and the n values for PEEK/Al₂O₃ composites were slightly higher than that of the neat PEEK polymer, indicating that the inclusion of the nano-filler made the crystallization mechanism more complex. However, the growth rate of crystallization was lowered as the nano- filler was introduced, and the decrease in growth rate reduced the grain size of the PEEK spherulites because of the lowering of molecule mobility during isothermal crystallization. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Tribological properties of micron silicon carbide filled poly(ether ether ketone)

The composite of poly(ether ether ketone) (PEEK) filled with micron silicon carbide (SiC) with different filler proportions was prepared by compression molding. The friction and wear properties of the composite were investigated at ambient conditions on a block on ring machine by running a plain carbon steel (AISI 1045 steel) ring against the composite block. The morphologies of the worn composite surfaces and the transfer film on the counterpart steel ring were examined with scanning electron microscopy and electron probe microanalysis. The results showed that the friction and wear of PEEK was slightly reduced at a filler proportion of micron SiC of 2.5–5.0 wt %. Abrasive wear was dominant for the PEEK composite; this was especially so at higher filler proportion. Meanwhile, abrasion and transfer to the composite surface of the counterpart steel ring were also observed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2611–2615, 1999     

Effect of dihydroxydiphenyl ether on poly(ether ether ketone)

A series of modified poly(ether ether ketone) (PEEK) polymers were synthesized by introduction of addition ether groups from dihydroxydiphenyl ether (DHDE) into the PEEK structure. The inherent viscosity of the DHDE-modified PEEK increased with reaction time at 320 °C. DSC thermograms showed the melting points of the obtained PEEK decreased with the increase of the DHDE content in the backbone. The degradation temperature (T_d) was slightly decreased by the introduction of DHDE. The crystallinity as measured via the X-ray diffraction (XRD) increases with the introduction of DHDE into the modified PEEK. The crystalline structure was identified as an orthorhombic structure with lattice constants a = 7.72 Å, b = 5.86 Å, and c = 10.24 Å. Due to the glass transition temperature (T_g) and the melting temperature (T_m) decreasing with the increase of the DHDE content in the reaction system. the processability of the resultant PEEK could be improved through this DHDE modification.     

Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes for pervaporation separation of ethanol/water solution

Polysulfone (PSF) hollow fiber membranes were spun by phase‐inversion method from 29 wt % solids of 29 : 65 : 6 PSF/NMP/glycerol and 29 : 64 : 7 PSF/DMAc/glycol using 93.5 : 6.5 NMP/water and 94.5 : 5.5 DMAc/water as bore fluids, respectively, while the external coagulant was water. Polyvinyl alcohol/polysulfone (PVA/PSF) hollow fiber composite membranes were prepared after PSF hollow fiber membranes were coated using different PVA aqueous solutions, which were composed of PVA, fatty alcohol polyoxyethylene ether (AEO₉), maleic acid (MAC), and water. Two coating methods (dip coating and vacuum coating) and different heat treatments were discussed. The effects of hollow fiber membrane treatment methods, membrane structures, ethanol solution temperatures, and MAC/PVA ratios on the pervaporation performance of 95 wt % ethanol/water solution were studied. Using the vacuum‐coating method, the suitable MAC/PVA ratio was 0.3 for the preparation of PVA/PSF hollow fiber composite membrane with the sponge‐like membrane structure. Its pervaporation performance was as follows: separation factor (α) was 185 while permeation flux (J) was 30g/m²·h at 50°C. Based on the experimental results, it was found that separation factor (α) of PVA/PSF composite membrane with single finger‐void membrane structure was higher than that with the sponge‐like membrane structure. Therefore, single finger‐void membrane structure as the supported membrane was more suitable than sponge‐like membrane structure for the preparation of PVA/PSF hollow fiber composite membrane. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 247–254, 2005     

Fine poly(ether ether ketone) powders

The physical form of polymers is often important for carrying out subsequent processing operations. For example, fine powders are desirable for molding and sintering compounds because they consolidate to produce void free components. The objective of this work is to prepare fine polymeric particulates suitable for processing into fiber reinforced polymer matrix composites. Micron size particles of poly(ether ether ketone) (PEEK) were prepared by rapidly quenching solutions of these materials. PEEK pellets were dissolved at temperatures near the PEEK melting point in a mixture of terphenyls and quaterphenyls; then the solution was quenched to a temperature between the T_g and T_m (≈ 225°C) by adding a room temperature eutectic mixture of diphenyl ether and biphenyl. A supersaturated, metastable solution of PEEK resulted, causing rapid nucleation. Fine PEEK particles rapidly crystallized from this solution. The average particle size was measured using transmission electron microscopy, atomic force microscopy, and by light scattering of aqueous suspensions which had been fractionated by centrifugation. The average particle diameter was about 0.6 μm. Three dimensional photomicrographs obtained via atomic force microscopy showed some aggregates in the suspensions. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 1571–1578, 1997     

Effect of posttreatment on morphology and properties of poly(ethylene‐co‐vinyl alcohol) microporous hollow fiber via thermally induced phase separation

Poly(ethylene‐co‐vinyl alcohol) (EVOH) hollow fiber membranes were prepared by thermally induced phase separation (TIPS) process. Water, methanol, and acetone were used to extract the diluents in the fibers, respectively. Bigger shrinkage of fibers during extractant evaporation was observed when water or methanol was used. Their interaction parameters with EVOH were calculated via Hansen solubility, respectively. The mechanism of hollow fiber volume shrinkage was discussed. It was found that affinity of the extractant with polymer was the critical factor except for the surface tension of extractant. Through the X‐ray diffraction analysis during extraction and evaporation, the crystallization behavior of the polymer was studied. From the SEM photos, it was observed that the volume shrinkage was derived from the collapse of porous structure. The fiber sample extracted by acetone had similar morphology with the sample freeze‐dried. The gas and water permeability were also measured and the results were coincident with the morphology of fibers and shrinkage data. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4106–4112, 2007     

Preparation and performances of poly(phthalazinone ether sulfone ketone) hollow fiber membranes with excellent thermotolerance

The cloud points of PPESK/NMP/H₂O ternary system at different temperatures were measured by titrimetric method. The binodal lines in the ternary phase diagram of the poly(phthalazinone ether sulfone ketone (PPESK) dope system was determined, on the basis of the cloud point experimental data being linearly fitted with the semiempirical linear cloud point correlation. Furthermore, phase separation behavior during the phase inversion of PPESK membrane‐forming system was discussed in terms of the phase diagram. Then, dry–wet spinning technique was employed in manufacturing PPESK hollow fiber membranes by immersion precipitation method. The cross‐section morphologies of hollow fibers were observed by scanning electronic microscopy. Also, the effects of dope solution composition and spinning parameters, including the coagulant composition and the spinning temperature on the separation performances of fibers, were evaluated by permeability measurements. The thermotolerance of the PPESK hollow fiber membranes prepared in the work was examined for the permeation operation at different temperatures and pressure differences. The experimental results showed that pure water flux increases several fold along with the temperature increases from 20 to 80°C at different operation pressures, while the solute rejection only decreases slightly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 878–884, 2006     

Tribological characteristics of nanometer Si3N4 filled poly(ether ether ketone) under distilled water lubrication

Nanometer Si₃N₄ filled poly(ether ether ketone) (PEEK) composite blocks with different filler proportions were prepared by compression molding. Their friction and wear properties under distilled water lubrication, as well as under ambient dry conditions, were investigated on a block on ring machine by running a plain carbon steel (AISI 1045 steel) ring against the PEEK composite block. The worn surfaces of nanometer Si₃N₄ filled PEEK and the transfer film were observed by scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). The results showed that distilled water could reduce the friction coefficient of nanometer Si₃N₄ filled PEEK but with the sacrifice of a large reduction in wear resistance. The SEM and EPMA pictures of the worn surfaces indicated that the wear mechanisms of nanometer Si₃N₄ filled PEEK under distilled water lubrication and ambient dry rubbing conditions were different. Under water lubrication, the dominant wear mechanism of the filled PEEK was severe abrasive wear with surface fracture. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1394–1400, 2001     

聚醚醚酮共混改性研究进展

综述了聚醚醚酮（PEEK）、聚醚酰亚胺（PEI）、聚四氟乙烯（PTFE）、热致液晶（TLCP）和聚醚砜（PES）等高性能工程塑料的共混改性研究进展,详细探讨了各种PEEK共混物的相容性、结晶行为、微观结构、热行为和力学性能等性能特征。PEEK与PEI在熔融和无定形状态下完全相容,常用于PEEK的结晶行为和微观结构的基础研究;与PTFE、TLCP、PES共混分别是提高PEEK的摩擦磨损性能、加工性能和热稳定性的有效手段。各种共混物的相容性好坏对其结晶行为和微观结构有重要影响,从而影响了共混物的力学性能。在此基础上,对PEEK共混改性领域进一步的研究方向和内容进行了讨论。     

磺化聚醚醚酮／氧化石墨复合膜的制备与表征

采用液相氧化法制备了氧化石墨（GO）,以浓硫酸为磺化剂与聚醚醚酮反应制备了磺化聚醚醚酮（SPEEK）。采用溶液共混法制备了不同组成的SPEEK／GO复合膜,并运用FTIR、XRD、DSC、TG对复合膜进行了表征。研究表明,当氧化石墨和磺化聚醚醚酮复合后,氧化石墨的层间距由0．8nm增大至1．1nm,这说明磺化聚醚醚酮极性基团或者高分子链段已经插入到氧化石墨片层之间。DSC结果显示,氧化石墨的加入,在一定程度上降低了SPEEK的结晶性能。TG分析表明,在温度低于300℃,复合膜的热稳定性比磺化聚醚醚酮的略有降低,但当温度高于450℃后,复合膜的热稳定性反而得到提高。     

Mechanical properties and sliding wear behavior of potassium titanate whiskers‐reinforced poly(ether ether ketone) composites under water‐lubricated condition

Polyetheretherketone (PEEK) composites reinforced with potassium titanate whiskers (PTW) were compounded using a twin‐screw extruder followed by injection molding. The effects of PTW on the mechanical properties, crystallization performances and wear behaviors of PEEK under water lubrication have been investigated. It was denoted that the yield strength, Young's modulus, and microhardness of the composites increased with increasing whisker content, but the elongation at break and the impact strength showed decreasing trend. It was revealed that the inclusion of PTW could effectively reduce the friction coefficient and enhance the wear resistance of the PEEK. The DSC tests showed that the crystallinity of the composite slightly decreased with the addition of PTW, which might imply that the crystallinity of PEEK was not the dominant factor that influenced the wear properties of the composites. The enhancement on the wear resistance was attributed to the reinforced effect of PTW on PEEK. The wear mechanism changed from fatigue wear into mild abrasive wear when the PTW was added into PEEK. The lowest wear rate 9.3 × 10^?8 mm³/Nm was achieved at 10 wt % PTW content. However, excessive whiskers would cause severe abrasive wear to the composite. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Relationships between morphology and mechanical properties

Mechanical properties such as the tensile modulus, yield (break) strength, and elongation to break (or yield) are measured for multiphase poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) blends. Specimens with three different levels of thermal histories (quenched, as‐molded, and annealed) are prepared in order to study their effects on the mechanical properties of PEEK/PES blends. Synergistic behavior is observed in the tensile modulus and tensile strength of the blends in almost the whole range of compositions. The ductility of quenched blends measured as the elongation to break (yield) shows an unexpected synergistic behavior in the blend containing 90 wt % PEEK, although a negative deviation from additive behavior is observed in the rest of the compositions. A ductile–brittle transition is observed between 50 and 75 wt % PEEK in the blend. The ductile–brittle transition in as‐molded blends shifts to 75–90 wt % PEEK. Annealed blends show predominantly brittle behavior in the whole composition range. The experimental data are further correlated with the theoretically predicted results based on various composite models. Although the prediction based on these equations fails to fit the experimental data in the whole composition range, the simplex equations that are normally used for blends showing synergistic behavior produced a reasonable fit to the experimental data. The mechanical properties obtained for different blend compositions are further correlated with their morphology as observed by scanning electron microscopy. Morphological observation shows a two‐phase morphology in PES‐rich blends, which is an interlocked morphology in which the disperse phase is not clearly visible in PEEK‐rich blends, and a cocontinuous type of morphology for a 50/50 composition. Considerable permanent deformation of both the disperse and matrix phase, especially in the case of quenched tensile specimens, demonstrates the remarkable adhesion present between the two phases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2887–2905, 2003