卫星反射面天线波束赋形的研究

卫星波束赋形天线普遍采用阵馈抛物反射面天线和单馈成形反射面天线。针对前者阵馈和后者反射面表面形状复杂的特点,本文分别采用了遗传算法和共轭梯度法对这两种天线进行了优化,并获得了中国版图的波束赋形,说明上述算法在卫星反射面天线波束赋形优化中是有效的。     

Scanning properties of large dual-shaped offset and symmetricreflector antennas

The scanning properties of shaped reflectors, both offset and circularly symmetric, are examined and compared to conic section scanning characteristics. Scanning of the pencil beam is obtained by lateral and axial translation of a single point source feed. The feed is kept pointed toward the center of the subreflector. The effects of power spillover and aperture phase error as a function beam scanning are examined for several different types of large reflector design including dual-offset, circularly symmetric large f/D, and smaller f/D dual reflector antenna system. It is shown that the Abbe-sine condition for improved scanning of an optical system cannot, inherently, be satisfied in a dual-shaped reflector system that is shaped for high gain and low feed spillover. The gain loss, with scanning, of a high-gain shaped reflector pair is demonstrated to be due to both aperture phase error loss and power spillover loss     

A variable power dual mode network for reconfigurable shaped beam antenna

A three output port variable power dual mode network is described. This network can be useful in driving a three element feed array feed of a communication satellite antenna to provide a dual mode reconfigurable shaped beam pattern.     

双馈源双偏置结构星载通信多波束天线

为了使星载通信天线产生赋形波束的同时,又能辐射具有扫描特性的点波束满足特殊情形下的通信要求,提出了一种以单馈源赋形反射面天线为基础,利用另一个馈源进行副反射面赋形,补偿主反射面口径相位差的方法,从而形成高效率点波束,并通过副反射面及对应馈源横向偏焦实现点波束扫描的目的。为了检验方法的有效性,仿真实验了一副口径为2.2 m 的赋形反射面天线。实验结果表明:赋形波束在服务区内部的最小增益是30.0dBi,点波束在服务区内部及周边区域扫描时具有比赋形波束更高的增益,因此,所提方法是有效的。     

Optimum beam scanning in offset single and dual reflector antennas

Optimum beam scanning in offset single reflector (paraboloid) and dual reflector (Cassegrain and Gregorian) antennas is considered. Analytical, computationally efficient solutions and results are presented for the optimum feed position, the constant beam direction feed loci, and the optimum feed position locus. Examples are presented to verify that the analysis technique yields the optimum feed position, which exhibits better gain, pattern symmetry, and sidelobe levels when compared with other feed positions producing beams scanned to the same direction. The solutions described were obtained under the ray optics approximation and a "receive mode" analysis. Although the developed method was applied to the antennas listed above, it can be easily extended to othern-reflector systems, shaped reflector antennas, lenses, and other similar systems.     

Synthesis of a laterally displaced cluster feed for a reflector antenna with application to multiple beams and contoured patterns

When a feed is displaced from the focus of a reflector, phase distortion results in the effective aperture distribution, which in turn gives rise to secondary beam distortion. In multiple beam or contour beam antennas, the feed normally consists of an array of identical elements located on a triangular lattice. Taking advantage of this arrangement, a "cluster" of feed elements instead of a single element may be used to control each beam. By adjusting the relative excitations of the elements in a cluster, the aperture phase distortion due to the feed displacement may be partially compensated. Two general methods for synthesizing the excitations for a laterally displaced feed cluster are presented. In the first method the excitations are chosen to minimize the weighted phase error in the effective aperture by analytical means. The second method determines the excitations by a gradient optimization algorithm which minimizes the weighted error between an objective and the actual power patterns in the secondary pattern space. The first method is roughly two orders of magnitude more efficient computationally than the gradient optimization algorithm, but not as flexible in application or as precise. Numerical results are presented for cluster feed designs and their application to the synthesis of contour patterns.     

毫米波赋形偏馈双反射面天线技术

为了实现一种具有高口面辐射效率、斜波束出射能力的口径天线,采用几何光学方法设计了一种偏馈双反射面天线.天线主反射面采用赋形设计,副反射面的设计过程中采用Snell定理作为约束条件.通过理论公式、数值模拟仿真和实验测试研究,实现了一种出射波束口径为110 cm、天线口面场分布为抛物形分布、波束出射方向与竖直方向成20°夹角的赋形偏馈双反射面天线.在中心频率95 GHz下,实测天线增益为59.7 dB,第一副瓣电平为-19dB,天线口径效率达到78%.     

一种T形太赫兹成像系统的设计

为了获得较高的帧速率以及降低成本,提出了一种带有波束扫描功能的T形太赫兹成像系统.系统包含两个共极化扇形波束扫描天线,它们以T字形正交摆放.收发天线具有基本相同的内部结构,由角锥喇叭馈源、产生扇形波束的椭圆主反射体以及用于实现波束扫描功能的旋转次反射体构成,而所有这些元件都镶嵌在两个平行金属板之间.给出了T形太赫兹成像系统的具体设计,提出了设计高性能扇形波束扫描天线的系统化方法,最后给出了一些实验的成像结果,以论证系统的功能.     

Single shaped reflector antennas for broadcasting satellites

For future direct broadcasting satellites in Japan, precisely contoured beam antennas will be required for onboard antennas. Single shaped-reflector antennas are suitable for that purpose, since they do not need complex feed networks. However, in a previous study, discontinuities in the reflector surface were observed. The problem of the discontinuity was circumvented in this work and the shaped reflectors were successfully designed to produce contoured beams for covering the Japanese islands for the downlink and feederlink antennas. The downlink antenna was fabricated, and the radiation pattern was verified by measurement. The radiation pattern meets the radio regulations imposed on the onboard antenna, such as sidelobe and cross-polarization characteristics     

一种星载通信混合反射面天线的设计方法

为了使星载通信天线产生1个赋形波束覆盖服务区,同时产生1个固定点波束和1个有限扫描点波束,该文提出一种由2个赋形反射面和3个馈源组成的混合反射面天线。该天线是以赋形主反射面共用为基础,等效为2副单馈源单偏置反射面天线和1副双偏置格里高利型赋形反射面天线,分别产生赋形波束、固定点波束和有限扫描点波束。通过对一副口径为1.2 m的天线各个波束进行仿真实验,赋形波束在Ku收、发频段时波束覆盖区边缘(EoC)方向性系数为27.5 dBi,固定点波束在C收、发频段时天线口径效率高于70%,通过将赋形副反射面及对应馈源横向偏焦实现Ka收、发频段的点波束在服务区内外的扫描。仿真结果表明,该混合反射面天线可实现C/Ku/Ka频段的同时通信任务。     

Feed network for dual beam reflector antennas

A primary feed network for doubly curved shaped-beam reflector antennas is described which allows simultaneous signal reception on two distinct elevation plane patterns such that the underside falloff separation between a fixed lower beam and a higher beam can be substantially varied in a lossless manner. A three-element feed array is employed wherein two elements of the array are interconnected by means of a sum-difference hybrid. The sum port generates the fixed low beam while the difference port generates an orthogonal beam pattern suitable for RF combining with an independent high beam generated by the third array element. Adjustment of the combining amplitude and phase relationships permits the variation of the underside falloff separation. The fixed low beam is, of course, also used for transmission at high power. Design parameters for a typical surveillance radar application axe discussed for a linearly polarized case. Calculated antenna patterns and free-space coverage diagrams are presented. The complexities of extending the feed network concept to handle switchable linear/circular polarization cases and an integral directional beacon pattern for L band systems are indicated.     

A dual doubly curved reflector antenna having good circular polarization characteristics

A new type of shaped-beam radar antenna having good polarization characteristics is described. This antenna is composed of a dual doubly curved reflector system and a feed horn with good axial ratio, such as a dual-mode horn. The rotationally symmetrical beam of the feed horn can be converted into a shaped beam by the reflector system without degradation of the axial ratio. The design of this type antenna is discussed and the experimental results of a model antenna with a cosecant squared beam are shown. Integrated cancellation ratio of the model was 22 dB.     

UTD analysis of a shaped subreflector in a dual offset-reflectorantenna system

The geometrical theory of diffraction (GTD) is known as an efficient high-frequency method for the analysis of electrically large objects such as a reflector antenna. However it is difficult to obtain geometrical parameters in order to apply GTD to an arbitrary shaped reflector, especially a subreflector. The geometrical parameters of an arbitrary shaped subreflector for the uniform theory of diffraction (UTD) analysis are derived based on differential geometry. The radiation patterns of various subreflector types, including hyperboloidal and a shaped subreflector, are evaluated by UTD. The computed result for the hyperboloidal reflector agrees well with that obtained by uniform asymptotic theory (UAT)     

A shaped dual-reflector antenna with a tilting flat subreflectorfor scanning applications

A scanning dual-offset reflector antenna using the simple motion of a flat subreflector to illuminate different parts of a shaped main reflector is presented. A particular case having a 20-degree linear field-of-view (for a DBS application) with a 30λ aperture diameter is explored. The main reflector surface is shaped to minimize the phase aberrations across the field-of-view. Once the main reflector surface is designed, the subreflector parameters are determined to ensure optimum focusing across the field-of-view     

可形成聚焦波束的双反射面天线仿真设计方法

给出基于几何光学方法的可形成聚焦波束的双反射面仿真设计方法。对于给定馈源 ,可以通过求解一组常微分方程 ,得到可在所需要聚焦点形成聚焦效果的反射面面形     

Synthesis of offset dual shaped subreflector antennas for control of Cassegrain aperture distributions

Many existing large ground reflector antennas have been designed as Cassegrain systems-i.e., paraboloid/hyperboloid combinations. Other large ground antennas are simply paraboloid designs. Upgrading the gain of these systems to a gain comparable to that obtainable with a dual shaped reflector antenna system has been an important and costly objective of many such ground stations. A potentially economic method for such an antenna upgrade is presented herein. It involves a redesign of only the subreflector portion of a Cassegrain antenna or the introduction of a subreflector feed system for a parabaloid. A pair of offset subreflectors are synthesized which will give a controllable high gain amplitude distribution in the aperture of the large paraboloid. The synthesis method that is used is based on an approximate formulation for an offset dual shaped high gain antenna that was first presented by Galindo-Israel and Mittra in 1977. In that approximate formulation, the geometrical optics (GO) energy was scattered from a subreflector and then from a second large reflector which reflected a uniform phase distribution. In the present offset dual shaped subreflector (DSS) antenna, the second reflection is from a smaller (sub) reflector and it scatters a spherical wave that feeds a hyperboloid or feeds a large paraboloid directly. Excellent results are shown for the approximate synthesis of the DSS.     

Peak gain of a Cassegrain antenna with secondary position adjustment

For an enclosed Cassegrain antenna, the loss of peak gain and beam deviation due to structural deformations of the primary reflector and rigid body displacements of the secondary reflector and of the feed are computed from the combined changes in the radio frequency (RF) path length. As the antenna moves in elevation, the position of the secondary reflector may be adjusted mechanically to minimize the loss of peak gain; a general method for the computation of the magnitude of such adjustments and of their effects on the gain and pointing of the system is presented. Numerical results are obtained for a particular case of a 45-ft diameter antenna designed for operation at 95.5 GHz RF for which the computed peak gain of the antenna varies significantly with the elevation angle. The results indicate that the loss of peak gain as the antenna moves in elevation can be substantially reduced by mechanical adjustment of the position of the secondary reflector.     

A shaped reflector antenna for 60-GHz indoor wireless LAN accesspoints

This paper addresses the design of a 60-GHz shaped reflector antenna that has to illuminate a predefined circular area without substantial spatial variation. At the boundary of this coverage area, the field strength has to fall off rapidly. Such efficient and confined illumination may be required in wireless networks that have to cope with a stringent link budget and/or require low channel dispersion. Typical examples are the emerging broadband wireless networks for customer premises and residential applications that will operate in the millimeter-wave frequency region. The particular property of the considered reflector is its diverging surface instead of the commonly applied converging shape. It is shown that the spatial variation within the defined coverage area can be within 1 dB, provided that the antenna is perfectly constructed. It is also shown that practical imperfections such as axial and lateral feed displacement and mispointing of the feed on top of effects due to blocking by the feed can contribute to spatial field variations on the order of a few decibels     

A shaped offset-fed dual-reflector antenna

A shaping scheme based on geometric optics for offset-fed dual-reflector antennas is presented. A ray tube emerging from a symmetric feed horn is transformed, after reflections, into a circular beam with a uniform phase and a prescribed radial power distribution on the aperture. In this scheme, Snell's law was not imposed on the main reflector. Based on this approximate solution, computer runs were taken for a 5.5-m dish baseline system, and very satisfactory results were obtained. The system so designed not only gives very low sidelobes but also provides a very high aperture efficiency. At 12 GHz an estimated 84 percent of aperture efficiency was achieved in spite of the severe constraint that the ray intersecting the edge of the main reflector meet a -10-dBi criterion.     

A generalized diffraction synthesis technique for high performancereflector antennas

Stringent requirements on reflector antenna performances in modern applications such as direct broadcast satellite (DBS) communications, radar systems, and radio astronomy have demanded the development of sophisticated synthesis techniques. Presented in the paper is a generalized diffraction synthesis technique for single- and dual-reflector antennas fed by either a single feed or an array feed. High versatility and accuracy are achieved by combining optimization procedures and diffraction analysis such as physical optics (PO) and physical theory of diffraction (PTD). With this technique, one may simultaneously shape the reflector surfaces and adjust the positions, orientations, and excitations of an arbitrarily configured array feed to produce the specified radiation characteristics such as high directivity, contoured patterns, and low sidelobe levels, etc. The shaped reflectors are represented by a set of orthogonal global expansion functions (the Jacobi-Fourier expansion), and are characterized by smooth surfaces, well-defined (superquadric) circumferences, and continuous surface derivatives. The sample applications of contoured beam antenna designs and reflector surface distortion compensation are given to illustrate the effectiveness of this diffraction synthesis technique