Large third-order optical nonlinearity of SrBi2Nb2O9 thin films fabricated by pulsed laser deposition

SrBi₂Nb₂O₉ (SBN) thin films with a single phase of layered perovskite structure have been fabricated on fused quartz substrates at room temperature by pulsed laser deposition. The XRD and AFM analysis indicated that the films had better crystallinity, less rough surface morphology, and larger grain size with increasing oxygen pressure. The nonlinear optical properties of the samples were determined using a single beam Z-scan technique at a laser wavelength of 532 nm with laser duration of 25 ps. The real and imaginary parts of the third-order nonlinear optical susceptibility χ⁽³⁾ of the films were measured to be 3.18 × 10^− 8 esu and 5.94 × 10^− 9 esu, respectively.     

Structural and magnetic properties of CoFe2O4 thin films deposited by laser ablation on Si (001) substrates

Cobalt ferrite (CoFe₂O₄) thin films have been deposited on Si (001) substrates, with different substrate temperatures (T_dep = 25 °C − 600 °C). The films were prepared by pulsed laser ablation with a KrF excimer laser (wavelength λ = 248 nm). The oxygen pressure during deposition was 2 × 10⁻² mbar. The films structure was studied by X-ray diffraction (XRD) and their surface was examined by scanning electron microscopy (SEM). The magnetic properties were measured with a vibrating sample magnetometer (VSM). For low deposition temperatures, the films presented a mixture of a CoFe₂O₄ phase, with the cubic spinel structure, and cobalt and iron antiferromagnet oxides with CoO and FeO stoichiometries. As the deposition temperature increased, the CoO and FeO relative content strongly decreased, so that for T_dep = 600 °C the films were composed mainly by polycrystalline CoFe₂O₄. The magnetic hysteresis cycles measured in the films were horizontally shifted due to an exchange coupling field (H_exch) originated by the presence of the antiferromagnetic phases. The exchange field decreased with increasing deposition temperature, and was accompanied by a corresponding increase of the coercivity and remanence ratio of the cycles. This behavior was due to the strong reduction of the CoO and FeO content, and to the corresponding dominance of the CoFe₂O₄ phase on the magnetic properties of the thin films.     

Cadmium oxide, indium oxide and cadmium indate thin films obtained by the sol-gel technique

Thin films of the mixed CdO-In₂O₃ system were deposited on glass substrates by the sol-gel technique. The precursor solution was obtained starting from the mixture of two precursor solutions of CdO and In₂O₃ prepared separately at room temperature. The In atomic concentration percentages (X) in the precursor solution with respect to Cd (1 − X), were: 0, 16, 33, 50, 67, 84 and 100. The films were sintered at two different sintering temperatures (Ts) 450 and 550 °C, and after that, annealed in a 96:4 N₂/H₂ gas mixture at 350 °C. X-ray diffraction patterns showed three types of films, excluding those constituted only of CdO and In₂O₃ crystals: i) For X ≤ 50 at.%, the films were constituted of CdO + CdIn₂O₄ crystals, ii) For X = 67 at.%, the films were only formed of CdIn₂O₄ crystals and iii) For X = 84 at.% the films were constituted of In₂O₃ + CdIn₂O₄ crystals. In all films in the 0 < X < 100 range, the formation CdIn₂O₄ crystals of this material was prioritized with respect to the formation of CdO and In₂O₃ materials. All films showed high optical transmission and an increase of the direct band gap value from 2.4 (for CdO) to 3.6 eV (for In₂O₃), as the X value increases. The resistivity values obtained were in the interval of 8 × 10^− 4 Ω cm to 10⁶ Ω cm. The CdIn₂O₄ films had a resistivity value of 8 × 10^− 3 Ω cm and a band gap value of 3.3 eV.     

Effect of yttrium doping on the dielectric properties of CaCu3Ti4O12 thin film produced by chemical solution deposition

Pure and yttrium substituted CaCu₃Ti_4 − xY_xO_{12 − x / 2} (x = 0, 0.02, 0.1) thin films were prepared on boron doped silica substrate employing chemical solution deposition, spin coating and rapid thermal annealing. The phase and microstructure of the sintered films were examined using X-ray diffraction and scanning electron microscopy. Dielectric properties of the films were measured at room temperature using electrochemical impedance spectroscopy. Highly ordered polycrystalline CCTO thin film with bimodal grain size distribution was achieved at a sintering temperature of 800 °C. Yttrium doping was found to have beneficial effects on the dielectric properties of CCTO thin film. Dielectric parameters obtained for a CaCu₃Ti_4 − xY_xO_{12 − x / 2} (x = 0.02) film at 1 KHz were k ∼ 2700 and tan δ ∼ 0.07.     

Deposition of zirconium oxynitride films by reactive cathodic arc evaporation and investigation of physical properties

The area of metal oxynitrides is poorly explored, and understanding of the fundamental mechanism that explains structural, mechanical, electrical, and optical properties is still insufficient. Therefore, the purpose of the present investigation is to analyze structural, electrical, and optical properties of ZrN_xO_y films deposited by reactive cathodic arc evaporation.Depending on the oxygen flow, cubic ZrN:O, monoclinic ZrO₂:N, and tetragonal ZrO₂:N phases films were prepared. The sheet resistance and the optical transmittance very much depend on the oxygen flow. Optical transparent ZrN_xO_y films with transmittance of 86% at 650 nm, the sheet resistance 1.1 · 10³ Ω/sq, and the figure of merit 2 · 10^− 4 Ω^− 1 are deposited with the 60 sccm oxygen flow.     

Structural,optical and electrical properties of In4Sn3O12 films prepared by pulsed laser deposition

Highly conducting (σ ∼ 2.6 × 10³ Ω⁻¹ cm⁻¹) In₄Sn₃O₁₂ films have been deposited using pulsed laser deposition (PLD) on glass and quartz substrates held at temperatures between 350 and 550 °C under chamber pressures of between 2.5 and 15 mTorr O₂. The crystallinity and the surface roughness of the films were found to increase with increasing substrate temperature. Electron concentrations of the order of 5 × 10²⁰ cm⁻³ and mobilities as high as 30 cm² V⁻¹ s⁻¹ were determined from Hall effect measurements performed on the films. Fitting of the transmission spectral profiles in the ultra-violet–visible spectrum has allowed the determination of the refractive index and extinction coefficient for the films. A red-shift in the frequency of plasmon resonance is observed with both increasing substrate temperature and oxygen pressure. Effective masses have been derived from the plasma frequencies and have been found to increase with carrier concentration indicating a non-parabolic conduction band in the material In₄Sn₃O₁₂. The optical band-gap has been determined as 3.8 eV from the analysis of the absorption edge in the UV. These results highlight the potential of these films as lower In-content functional transparent conducting materials.     

Photoluminescence behaviors in ZnGa2O4 thin film phosphors deposited by a pulsed laser ablation

ZnGa₂O₄ thin film phosphors have been deposited using a pulsed laser deposition technique on Si (1 0 0) and Al₂O₃ (0 0 0 1) substrates at a substrate temperature of 550 °C with various oxygen pressures 100, 200 and 300 mTorr, and various substrate temperatures of 450, 550 and 650 °C with a fixed oxygen pressure of 100 mTorr. The films grown under different deposition conditions have been characterized using microstructural and luminescent measurements. Under the different substrate temperatures, ZnGa₂O₄ thin films show the different crystallinity and luminescent intensity. The crystallinity and photoluminescence (PL) of the ZnGa₂O₄ films are highly dependent on the deposition conditions, in particular, oxygen pressure, substrate temperature, a kind of substrates. The luminescent spectra show a broad band extending from 350 to 600 nm peaking at 460 nm. The PL brightness data obtained from the ZnGa₂O₄ films grown under optimized conditions have indicated that the sapphire is one of the most promised substrates for the growth of high quality ZnGa₂O₄ thin film phosphor.     

V-doping effects on ferroelectric properties of K0.5Bi4.5Ti4O15 thin films

V-doped K_0.5Bi_4.5Ti₄O₁₅ (K_0.5Bi_{4.5 − x/3}Ti_4 − xV_xO₁₅, KBTiV-x, x = 0.00, 0.01, 0.03, and 0.05) thin films were prepared on a Pt(111)/Ti/SiO₂/Si(100) substrate by a chemical solution deposition method. The thin films were annealed by using a rapid thermal annealing process at 750 °C for 3 min in an oxygen atmosphere. Among them, KBTiV-0.03 thin film exhibited the most outstanding electrical properties. The value of remnant polarization (2P_r) was 75 μC/cm² at an applied electric field of 366 kV/cm. The leakage current density of the thin film capacitor was 5.01 × 10⁻⁸ at 100 kV/cm, which is approximately one order of magnitude lower than that of pure K_0.5Bi_4.5Ti₄O₁₅ thin film capacitor. We found that V doping is an effective method for improving the ferroelectric properties of K_0.5Bi_4.5Ti₄O₁₅ thin film.     

Electrical properties of alumina films grown on Si at low temperature using catalytic CVD

The electrical properties of alumina films formed at substrate temperatures as low as 27 °C using tri-methyl aluminum (TMA) and molecular oxygen (O₂) by catalytic chemical vapor deposition (Cat-CVD) have been investigated by capacitance-voltage (C-V), current-voltage (I-V) measurements and X-ray photoelectron spectroscopy (XPS). Substrate temperature dependence of dielectric constant and leakage current of the films has been explained on the basis of deficiency in oxygen. Interface trapping density of the order of 10⁹ ev^− 1cm^− 2 has been obtained. Angle resolved XPS measurements have revealed that the direct bonding of alumina and Si was realized with very small interface trapping density.     

Transparent conducting Nb-doped anatase TiO2 (TNO) thin films sputtered from various oxide targets

Transparent conducting Nb-doped anatase TiO₂ (TNO) epitaxial films were sputtered from TiO₂-, Ti₂O₃-, and Ti-based targets at various oxygen partial pressures (Po₂). Using the TiO₂- and Ti₂O₃-based targets, highly conductive films showing a resistivity (ρ) of ~ 3 × 10^− 4 Ω cm could be formed without postdeposition treatment. In the case of the TNO films formed from the Ti-based target, reductive annealing had to be carried out at a temperature of 600 °C to achieve similar resistivity values. Thus, the use of oxide targets is preferable to obtain as-grown transparent conducting TNO films. In particular, the Ti₂O₃-based target is practically advantageous, because it offers a wide range of optimal Po₂ values at which ρ values of the order of 10^− 4 Ω cm are achievable.     

Influence of Ga2O3 addition on transparent conductive oxide films of In2O3-ZnO

Influence of incorporation of Ga in amorphous In-Zn-O transparent conductive oxide films was investigated as a function of Zn/(Zn + In). For In-Zn-O films with no Ga₂O₃, the range of Zn/(Zn + In) ratio where the amorphous phase appears became narrow at a substrate temperature of 250 °C. With increasing Ga₂O₃ quantity, amorphous films were obtained even at a high substrate temperature of 250 °C in a wider range of Zn/(Zn + In) than that of In-Zn-O films with no Ga₂O₃. This means that the trend of crystallization at higher substrate temperature was disturbed with additional Ga incorporation. For the film deposited from ZnO:Ga (Ga₂O₃: 4.5-7.5 wt%) and In₂O₃ targets, we obtained a resistivity of 2.8 × 10⁻⁴ Ω cm, nearly the same value as that for an In-Zn-O film with no Ga₂O₃. The addition of more than 7.5 wt% Ga₂O₃ induced a widening of the optical band gap.     

Structural and electrical properties of HfO2/Dy2O3 gate stacks on Ge substrates

In the present work we report on the structural and electrical properties of metal-oxide-semiconductor (MOS) devices with HfO₂/Dy₂O₃ gate stack dielectrics, deposited by molecular beam deposition on p-type germanium (Ge) substrates. Structural characterization by means of high-resolution Transmission Electron Microscopy (TEM) and X-ray diffraction measurements demonstrate the nanocrystalline nature of the films. Moreover, the interpretation of the X-ray reflectivity measurements reveals the spontaneous growth of an ultrathin germanium oxide interfacial layer which was also confirmed by TEM. Subsequent electrical characterization measurements on Pt/HfO₂/Dy₂O₃/p-Ge MOS diodes show that a combination of a thin Dy₂O₃ buffer layer with a thicker HfO₂ on top can give very good results, such as equivalent oxide thickness values as low as 1.9 nm, low density of interfacial defects (2-5 × 10¹² eV^− 1 cm^− 2) and leakage currents with typical current density values around 15 nA/cm² at V_g = V_FB − 1V.     

Physical properties of transparent conducting Cd-Te-In-O thin films: Outlining a thermodynamic system for transparent conducting oxides

Cd-Te-In-O thin films are grown by pulsed laser deposition using a composite target of CdTe powder embedded in an indium matrix. Oxygen pressures range from 2.00 to 6.67 Pa at a substrate temperature of 420 °C. The structure, optical transmission and sheet resistance of the films are measured. Substitutional compounds with In_2 − 2x(Cd,Te)_2xO₃ stoichiometry are found at high oxygen pressures. A ternary phase diagram of the CdO-In₂O₃-TeO₂ system shows the relationship between the structure and the stoichiometry of the films. To evaluate film performance, a figure of merit is proposed based on the relationship between the integral photonic flux and the sheet resistance. The best figure of merit values corresponds to a sample prepared at 3.8 Pa O₂ that consists of (In₂O₃)_0.3(CdTe₂O₅)_0.7 and exhibits an optical band gap of 3.0 eV. This sample is a suitable substrate for electrodeposition due to its good electrochemical stability.     

Preparation of anatase TiO2 thin films by vacuum arc plasma evaporation

Anatase titanium dioxide (TiO₂) thin films with high photocatalytic activity have been prepared with deposition rates as high as 16 nm/min by a newly developed vacuum arc plasma evaporation (VAPE) method using sintered TiO₂ pellets as the source material. Highly transparent TiO₂ thin films prepared at substrate temperatures from room temperature to 400 °C exhibited photocatalytic activity, regardless whether oxygen (O₂) gas was introduced during the VAPE deposition. The highest photocatalytic activity and photo-induced hydrophilicity were obtained in anatase TiO₂ thin films prepared at 300 °C, which correlated to the best crystallinity of the films, as evidenced from X-ray diffraction. In addition, a transparent and conductive anatase TiO₂ thin film with a resistivity of 2.6 × 10^− 1 Ω cm was prepared at a substrate temperature of 400 °C without the introduction of O₂ gas.     

The effect of deposition parameters on the properties of SrCu2O2 films fabricated by pulsed laser deposition

SrCu₂O₂ (SCO) thin films have been fabricated by pulsed laser deposition at oxygen partial pressures between 5 × 10^− 5-5 × 10^− 2 mbar and substrate temperatures from 300 °C to 500 °C. All films were single-phase SrCu₂O₂, p-type materials. Films deposited at a substrate temperature of 300 °C and oxygen pressure 5 × 10^− 4 mbar exhibited the highest transparency (∼ 80%), having conductivity 10^− 3 S/cm and carrier concentration around 10¹³ cm^− 3. Films deposited at oxygen partial pressure higher than 10^− 3 mbar exhibited higher conductivity and carrier concentration but lower transmittance. Depositions at substrate temperatures higher than 300 °C gave films of high crystallinity and transmittance even for films as thick as 800 nm. The energy gap of SrCu₂O₂ thin films was found to be around 3.3 eV.     

Multiferroic properties of BiFeO3/Bi4Ti3O12 double-layered thin films fabricated by chemical solution deposition

Multiferroic BiFeO₃/Bi₄Ti₃O₁₂ (BFO/BTO) double-layered film was fabricated on a Pt(111)/Ti/SiO₂/Si(100) substrate by a chemical solution deposition method. The effect of an interfacial BTO layer on electrical and magnetic properties of BFO was investigated by comparing those of pure BFO and BTO films prepared by the same condition. The X-ray diffraction result showed that no additional phase was formed in the double-layered film, except BFO and BTO phases. The remnant polarization (2P_r) of the double-layered film capacitor was 100 μC/cm² at 250 kV/cm, which is much larger than that of the pure BFO film capacitor. The magnetization-magnetic field hysteresis loop revealed weak ferromagnetic response with remnant magnetization (2M_r) of 0.4 kA/m. The values of dielectric constant and dielectric loss of the double-layered film capacitor were 240 and 0.03 at 100 kHz, respectively. Leakage current density measured from the double-layered film capacitor was 6.1 × 10^− 7 A/cm² at 50 kV/cm, which is lower than the pure BFO and BTO film capacitors.     

Electrical transport and structural study of CuCr1 − xMgxO2 delafossite thin films grown by pulsed laser deposition

The growth and properties of delafossites CuCr_1 − xMg_xO₂ thin films are examined. These films are grown by pulsed laser deposition. As a class of materials delafossites have received recent interest since some members show p-type behavior. While not considered true wide-bandgap materials due to a narrow indirect bandgap that fails to adsorb light due to a forbidden same parity transition, optical transparencies greater than 40% in the visible can be observed. In order to be useful for transparent device applications, CuCr_1 − xMg_xO₂ films are needed with low resistivity and high optical transparency. Epitaxial films of CuCr_1 − xMg_xO₂ were grown on c-sapphire, examining the effects of oxygen pressure and growth temperature on film properties. Films were realized with resistivity of ~ 0.02 Ω-cm and optical transparency of 40% in the visible. The formation of a problematic secondary minority spinel phase of (Cu,Mg)Cr₂O₄ is discussed. While conductivity increases substantially with Mg doping, the incidence of the spinel phase increases as well.     

Properties of La-substituted Na0.5Bi4.5Ti4O15 ferroelectric thin films

Ferroelectric Na_0.5La_0.5Bi₄Ti₄O₁₅ (NaLaBTi) thin films were prepared by a chemical solution deposition method. The NaLaBTi thin films annealed at 750 °C under oxygen atmosphere were randomly oriented polycrystalline. Electrical properties of the NaLaBTi thin films were compared to Na_0.5Bi_4.5Ti₄O₁₅ thin films and better properties were observed in the NaLaBTi thin films. Remnant polarization (2P_r) and coercive electric field (2E_c) were 43 µC/cm² and 204 kV/cm at an applied electric field of 478 kV/cm, respectively. Leakage current density was 1.95 × 10^− 6 A/cm² at 100 kV/cm. Dielectric constant and dielectric loss were 805 and 0.05 at 1 kHz, respectively. Switchable polarization was suppressed by 15% after 1.44 × 10¹⁰ switching cycles.     

Evaluation of Y2O3 gate insulators for a-IGZO thin film transistors

In this work, Y₂O₃ was evaluated as a gate insulator for thin film transistors fabricated using an amorphous InGaZnO₄ (a-IGZO) active layer. The properties of Y₂O₃ were examined as a function of various processing parameters including plasma power, chamber gas conditions, and working pressure. The leakage current density for the Y₂O₃ film prepared under the optimum conditions was observed to be ~ 3.5 × 10^− 9 A/cm² at an electric field of 1 MV/cm. The RMS roughness of the Y₂O₃ film was improved from 1.6 nm to 0.8 nm by employing an ALD (Atomic Layer Deposition) HfO₂ underlayer. Using the optimized Y₂O₃ deposition conditions, thin film transistors (TFTs) were fabricated on a glass substrate. The important TFT device parameters of the on/off current ratio, sub-threshold swing, threshold voltage, and electric field mobility were measured to be 7.0 × 10⁷, 0.18 V/dec, 1.1 V, and 3.3 cm²/Vs, respectively. The stacked insulator consisting of Y₂O₃/HfO₂ was highly effective in enhancing the device properties.     

Fabrication and photocatalytic property of Pt-intercalated layered perovskite niobates H1−xLaNb2−xMoxO7 (x = 0–0.15)

H_1−xLaNb_2−xMo_xO₇ was prepared by solid-state reaction followed by an ion-exchange reaction. Pt was incorporated in the interlayer of H_1−xLaNb_2−xMo_xO₇ by the stepwise intercalation reaction. The H_1−xLaNb_2−xMo_xO₇ showed hydrogen production activity and the activities were greatly enhanced by Pt co-incorporating. The x value in H_1−xLaNb_2−xMo_xO₇ had an important effect on the photocatalytic activity of the catalyst. When the x = 0.05, the H_1−xLaNb_2−xMo_xO₇/Pt showed a photocatalytic activity of 80 cm³ h⁻¹ g⁻¹ hydrogen evolution rate in 10 vol.% methanol solution under irradiation from a 100 W mercury lamp at 333 K.