Dual‐passband bandpass‐filtering power divider using half‐mode substrate integrated waveguide resonator with high frequency selectivity

In this paper, a half‐mode substrate integrated waveguide (HMSIW) power divider with bandpass response and good frequency selectivity is proposed. The proposed power divider includes input/output microstrip lines, four HMSIW resonators, cross‐coupling circuits, and an isolation resistor. The dual‐band bandpass‐filtering response is obtained by using the dual‐mode slotted HMSIW. To get good frequency selectivity, the input/output cross‐coupling circuits have been used, and several transmission zeros can be observed. A dual‐band filtering‐response HMSIW power divider is designed, fabricated and measured. The total size of the fabricated power divider is 0.58λg × 0.45λg. The measured results show a reasonable agreement with the simulated ones. The measured central operating frequencies of the dual‐band HMSIW power divider are at 2.43 and 3.50 GHz, respectively. The measured 3‐dB fractional bandwidth is about 13.3% and 6.3% in the two passbands, and the measured output isolation is about 20 dB.     

Enhanced waveguide bandpass filters using S‐shaped resonators

This article presents a new solution for stopband performance improvement of rectangular waveguide bandpass filters using S‐shaped resonator loaded waveguide configurations at microwave and millimeter‐wave frequencies. The proposed filter structure is compact in size when comparing with the standard E‐plane counterpart. Compactness is achieved by taking advantage of the properties of slow wave effect in half wavelength resonators. Periodicity is readily imposed upon cascading the S‐shaped resonators within the rectangular waveguide. The structure is simple and compatible with E‐plane technology. This type of bandpass filters can be easily realized with a single metallo‐dielectric insert within a standard rectangular waveguide. Simulation and experimental results are presented to validate the argument along with some design guidelines. © 2009 Wiley Periodicals, Inc. Int J RF and Microwave CAE 2009.     

Dual‐band ridge waveguide filters for high‐selectivity wireless base station applications

Dual‐band filters simplify the system architecture considerably by replacing doubly multiplexed filters. This is especially important in base stations for wireless communications, where high‐selective filtering functions are required, with very stringent requirements in size and insertion losses. For this goal, compact dual‐band filters realized in air‐filled metallic ridge waveguides are proposed. The dual‐band approach shown in this article allows fulfilling the stringent insertion loss specifications of very selective filtering functions. The ridge waveguide resonators are placed in a canonical folded top‐bottom structure layout. Coupling sections that provide cross‐couplings are realized by irises opened in the intermediate wall. Given the high‐order of the dual‐band filter required for actual wireless applications, an efficient modeling by the mode‐matching method is used. A complete challenging filter prototype with 16 poles and 10 transmission zeros with specifications of typical wireless transceivers is built and tested for verification. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:703–712, 2016.     

Compact dual‐band bandpass filter and diplexer using hybrid resonant structure with independently controllable dual passbands

In this article, a compact dual‐band bandpass filter (BPF) is developed using a hybrid resonant structure, which consists of a microstrip stub‐loaded dual‐mode resonator and a slotline stub‐loaded dual‐mode resonator. These two resonators, both having two controllable resonant modes and one transmission zero (TZ), are analyzed and used to construct two desired passbands of a dual‐band BPF. Multiple TZs are generated by introducing a source‐load coupling, thus improving the selectivity of the passbands. Then, the dual‐band BPF is reshaped to configure a compact diplexer. The inherent TZs of the two proposed resonators are designed to improve the frequency property and port isolation of the diplexer. Finally, a dual‐band BPF and a diplexer with the lower and upper passbands centered at 2.45 and 3.45 GHz, respectively, are designed, fabricated, and measured to verify the proposed structure and method.     

Microstrip dual‐band bandpass filters using parallel‐connected open‐loop ring resonators

This article proposes a microstrip dual‐band bandpass filter that uses parallel‐connected open‐loop ring resonators. Compared to many microstrip dual‐band filters, the advantages of using microstrip open‐loop ring resonators are easy calculation (half‐guided‐wavelength), easy fabrication (equal width for all 50‐Ω lines and without grounding holes), and direct connection to external feed lines (reducing insertion loss caused by gap couplings). Another advantage of the filter is an asymmetrical feed on the ring resonator that provides sharp rejections at its adjacent bands. The input and output matches of resonators to the external feed lines are derived using a simple transmission‐line theory. The results of the derivation provide a simple design rule for filter designers. Simulated and measured results are presented with good agreement. The filter has minimum insertion loss of 1.25 dB at 1.85 GHz and 1.6 dB at 2.33 GHz. The 3‐dB fractional bandwidths are 5.9% for the 1.9‐GHz bandpass filter and 4.7% for the 2.4‐GHz bandpass filter, respectively. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2008.     

High‐order dual‐band superconducting filter with independently controllable passbands and wide stopband

A stepped‐impedance‐stub loaded stepped‐impedance resonator (SISLSIR) is proposed to design a dual‐band bandpass filter. The even‐ and odd‐mode frequencies and the coupling strength of the proposed resonators can be independently designed and adjusted. A dual‐feedline structure is used to meet the required external couplings of the 2 passbands. Thus, both the center frequencies and the bandwidths of the 2 passbands can be independently controlled. A 6‐pole dual‐band filter with the passbands of 3300～3600 MHz and 4800～5000 MHz is successfully designed using the proposed method and fabricated with YBCO/MgO high‐temperature superconducting (HTS) wafer. The measured results of the filter exhibit high performance and match well with the simulations. The measured insertion losses are less than 0.2/0.3 dB, and the return losses are greater than 15/14 dB for the lower/upper passbands, respectively. The out‐of‐band rejection is greater than 68 dB up to 12 GHz.     

Widely separated dual‐band half‐mode SIW bandpass filter

A novel half‐mode substrate integrated waveguide (HMSIW) based dual‐band bandpass filter (DBBPF) is proposed. Back to back connected two defected ground structure (DGS) resonators on the top layer of HMSIW cavity constitute the passband with two transmission zeros (TZs) at a lower frequency. The higher modes TE₃₀₁ and TE₃₀₂ of HMSIW cavity give the passband response at higher frequency using the mode shifting technique with slot perturbation. The source‐load coupling has been used to create finite frequency TZs to improve the selectivity of the second passband. Therefore, the proposed filter gives two widely separated passbands, center frequencies (CFs) at 5.83 and 18.1 GHz with an attenuation of greater than 10 dB between the passbands. The synthesized filter is fabricated using a low‐cost single layer PCB process, and the measured S‐parameters are almost mimic the EM‐simulation results.     

Compact bandpass filter using CMRC‐based dual‐behavior resonator

This article presents a novel bandpass filter (BPF) using two proximity‐coupled dual‐behavior resonators (DBRs). The employed DBR is implemented by a single shunt stub with the compact microstrip resonator cell at its open end instead of the traditional dual stubs in cross‐shape. Due to the adoptions of the proposed DBR and proximity‐coupling scheme, both the transverse and longitudinal dimensions of the proposed BPF are reduced significantly. To verify the proposed idea, a demonstration microstrip BPF is designed and fabricated, and good agreement between the simulated and measured results can be observed, showing low loss and high selectivity due to four transmission zeroes in the stopband.     

Miniaturized substrate integrated waveguide 5G LTCC bandpass filter exploiting capacitive loaded cavities

In this article, a compact bandpass filter with a pair of transmission zeros exploiting capacitive loaded cavities is presented. The proposed filter structure is mainly composed of coplanar waveguide (CPW) feeding structures and four substrate integrated waveguide (SIW) resonators. The size of the filter has been greatly reduced due to the capacitive loaded circle metallic septum and the vertical coupling of stacked cavities in three dimensional structures by low temperature co‐fired ceramic technology. The filter not only achieves the advantages of high‐selectivity, a much wider upper stopband bandwidth, but also realizes a miniaturized volume of 3.35 × 2.10 × 0.66 mm³. The simulated and measured results show the bandpass filter achieves a center frequency of 28 GHz with 3 dB fractional bandwidth of 8%. The filter is suitable for application in 5G wireless communication.     

A covering Ka‐band two‐way switch filter module using a three‐line and an E‐plane waveguide band‐pass filters

A millimeter‐wave ultrawideband two‐way switch filter module is presented in this article. The switch filter module covers whole Ka‐band (26–40 GHz), and is composed of two wideband band‐pass filters and two monolithic microwave integrated circuit (MMIC) single pole two throw (SP2T) switches. One filter is realized using E‐plane iris waveguide band‐pass filter, and another is realized by a novel 11‐pole three‐line microstrip structure band‐pass filter. Compared with the traditional three‐line filter, the proposed three‐line filter not only retains virtues of the traditional three‐line filter, but also resolves drawbacks of it, which include discontinuities between adjacent sections, many parameters of design, and no effective matching circuits at input/output ports. The developed switch filter module is fabricated using hybrid integrated technology, which has a size of 51 × 26 × 9.8 mm³, and interconnections between MMICs and microstrip are established by bond wires. The fabricated switch filter module exhibits excellent performances: for two different states, the measured insertion loss and return loss are all better than 7 and 10 dB in each pass‐band, respectively. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:305–310, 2015.     

A novel wideband bandpass filter based on CSRR‐loaded substrate integrated folded waveguide

A novel wideband bandpass filter based on folded substrate integrated waveguide (FSIW) is presented in the article. Five square complementary split‐ring resonators (CSRRs) are etched in the middle layer of the FSIW. By adjusting the physical size of the CSRR structure, the resonant frequency of the CSRRs can be tuned at the same time and the stopband performance can be changed. As transverse electromagnetic (TEM) mode can be transmitted in the stripline, FSIW excited by stripline shows wider passband than that excited by microstrip line directly. To achieve perfect impedance matching, two microstrip lines to stripline transitions are added in two ports of the filter. The proposed bandpass filter exhibits compact size, high selectivity, good stopband rejection, lower radiation loss, and wideband performances. The measured results show that the fractional bandwidth of the filter is about 35.5%. The measured return loss is better than 15 dB from 4.84 GHz to 6.90 GHz, and the insertion loss is less than 1.2 dB. The comparison between the simulated results and the measured ones validate the possibility of the technology that combines the FSIW and CSRR.     

A bandpass filter using modified half mode substrate integrated waveguide technique

This article reports a novel bandpass filter using modified half mode substrate integrated waveguide technique. The via‐fences are deployed as impedance inverters for the proposed filter to reduce its footprints, which are extracted by using a full‐wave electromagnetic simulator HFSS for the filter design. Detailed design procedure is discussed. A bandpass filter having a center frequency of 10.03 GHz and a pass band from 9.78 to 10.3 GHz is designed for demonstration, and experiments are carried out for the validation. Good agreements between experiment and simulated results are obtained, which show that the proposed filter has a compact size, a low insertion loss, and a high selectivity. It is attractive for the radio communication system. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:277–281, 2015.     

Miniaturized rectangular waveguide filters

Two types of miniaturized rectangular waveguide filters are presented. Miniaturization is achieved using the slow‐wave effect of electromagnetic bandgap (EBG) surfaces and the left‐handed properties of split ring resonators (SRRs). The proposed EBG waveguide bandpass filter performs passband in the frequency range, which corresponds to the waveguide with the lower recommended operating band consequently enabling significant miniaturization of the structure. The SRR‐loaded bandstop filter makes use of the effect imposed by left‐handed medium (LHM), which is created by a combination of SRRs and wireline on the dielectric slab. Both filters are designed, simulated, and tested. Experimental results of the SRR‐loaded bandstop filter are presented to demonstrate feasibility of the proposed structures. © 2007 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2007.     

Ultra‐compact dual mode dual band filter based on separate electric and magnetic coupling paths

A pair of dual mode independent controllable resonators used to realize dual band pass filter with good frequency selectivity and isolation is presented. The resonators are directly connected to input/output and are coupled through electric and magnetic coupling in two different paths. Magnetic coupling between the resonators is achieved using a common grounded via‐hole between the two set of quarter‐wavelength resonators. Electric coupling is achieved through open edge coupling of the resonators. Two independent resonators with Separate Electric and Magnetic Coupling (SEMC) paths produce an independently controllable dual band filter response and also additional transmission zeros (TZs) at the edges of the pass bands. The TZs are introduced to improve the selectivity of the filter. Filter exhibits desired pass band response at the Universal Mobile Telecommunications System (UMTS) band (1.95‐2.2 GHz) and Worldwide Interoperability for Microwave Access (WiMAX) band (3.4‐3.6 GHz). Proposed compact filter is implemented on RT/Duroid 5880 (ε_r = 2.2) substrate with thickness of 0.785 mm and surface area of 15 × 12 sq. mm.     

Miniaturized substrate integrated waveguide filter using fractal open complementary split‐ring resonators

A miniaturized substrate integrated waveguide (SIW) bandpass filter using fractal open complementary split‐ring resonators (FOCSRRs) unit‐cell is proposed. The proposed structure is realized by etching the proposed FOCSRR unit‐cells on the top metal surface of the SIW structure. The working principle of the proposed filter is based on the evanescent‐mode propagation. The proposed FOCSRRs behave as an electric dipoles in condition of the appropriate stimulation, which are able to generate a forward‐wave passband region below the cutoff frequency of the waveguide structure. Since, the electrical size of the proposed FOCSRRs unit‐cell is larger than the conventional OCSRRs unit‐cell; therefore, the FOCSRR unit‐cell is a good candidate to miniaturize the SIW structure. The proposed filter represents high selectivity and compact size because of the utilization of the sub‐wavelength resonators. The introduced filter is simulated by a 3D electromagnetic simulator. In order to validate the ability of the proposed topology in size reduction, 1‐ and 2‐stage of the proposed filters have been fabricated based on the standard printed circuit board process. The measured S‐parameters of the fabricated filters are in a good agreement with the simulated ones. The proposed SIW filters have many advantages in term of compact size, low insertion loss, high return loss, easy fabrication and integration with other circuits. It is the first time that the FOCSRR unit‐cells were combined with the SIW structure for miniaturization of this structure. Furthermore, a wide upper‐stopband with the attenuation >20 dB in the range of 3–8 GHz is achieved. The results show that, a miniaturization factor about 75.5% has been obtained.     

Compact ultra‐wideband bandpass filter with variable notch characteristics based on transversal signal‐interaction concepts

A novel technique is presented to design highly compact microstrip ultra‐wideband (UWB) bandpass filters that exhibit high selectivity quasi‐elliptical response. The design is based on transversal signal‐interaction concepts that enable the inclusion of single or dual notch‐bands within the filter's passband to eliminate interference from other services that coexist within the UWB spectrum. The filter configuration comprises of two transmission paths which include folded T‐shaped stepped impedance resonators (SIRs) that are capacitively coupled with the input/output lines to enable signal transmission. It is shown that by combining the filters of different passband centre frequencies an UWB filter can be realised with either a single‐ or dual‐notch function. The theoretical performance of the filter is corroborated via measurements to confirm that the proposed filter exhibits UWB passband of 123% for a 3 dB fractional bandwidth, a flat group‐delay with maximum variation of less than 0.3 ns, passband insertion loss less than 0.94 dB, high selectivity, a sharp rejection notch‐band with attenuation of ?23 dB, and a good overall out‐of‐band performance. Furthermore, the filter occupies a significantly small area of 94 mm² compared with its classical counterparts. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:549–559, 2014.     

A tunable third‐order bandpass filter based on combining dual‐mode square‐shaped substrate integrated waveguide resonator with triangular‐shaped resonator

A frequency reconfigurable third‐order bandpass filter based on two substrate integrated waveguide (SIW) cavities is presented in this article. The purposed filter consists of a dual‐mode square‐shaped resonator and a triangular‐shaped resonator. In the square‐shaped cavity, four lumped capacitors are loaded as electrical tuning elements in the area where the electric fields of diagonal TE₂₀₁ and TE₁₀₂ modes are strongest. And an another capacitor is loaded at the suitable region of the triangular‐shaped cavity. Square‐shaped cavity introduces two transmission zeros and the triangular‐shaped cavity can suppress out‐of‐band spurious modes. The method that combines the resonators with different shapes and multiple modes into an organic whole cannot only achieve synchronous tuning but also have complementary advantages and improve out‐of‐band rejection. To verify its practicality, a SIW reconfigurable bandpass filter is simulated when the capacitance value varies from 0 to 1.4 pF and measured at 0.7, 0.8, and 0.9 pF, respectively. Measured results show that when the center frequency is tuned from 3.42 to 3.52 GHz, the proposed filter exhibits good tuning performance with insertion loss of less than 2.5 dB and return loss of better than 10 dB, which is suitable for fifth‐generation communication system.     

A folded dual‐mode bandpass filter with circular waveguide

In this article, a folded circular waveguide dual‐mode filter without tuning screws is designed for the fifth‐generation (5G) mobile communication system. The folded filter is composed of two stacked circular cavities operated at 3.5 GHz. Each cavity has two resonant modes, which can generate and control two transmission zeroes at specific frequencies. Through a coupling iris, the two single‐cavity filters are connected together, and can control four poles, which helps to expand the 3dB fractional bandwidth to 11.4%. The measured insertion losses are around 0.5 dB in the passband (from 3.4–3.6 GHz). The experiment results show an excellent agreement with the simulation results. Such folded filters have the advantages of very low insertion loss, compact size, high frequency selectivity, and low cost.     

Compact dual‐ and triband bandpass filter using frequency selecting coupling structure loaded stepped‐impedance resonator

This article presents two novel resonators, that is, frequency selecting coupling structure loaded stepped‐impedance resonator (FSCSLSIR) and π‐section loaded FSCSLSIR. The resonator behaviors and guidelines are given to design FSCSLSIR dual‐band bandpass filter (BPF) and π‐section loaded FSCSLSIR triband BPF. The proposed dual‐ and triband BPF have very compact sizes of 0.13 λ_gd × 0.06 λ_gd and 0.115 λ_gt × 0.074 λ_gt, respectively. Moreover, good return loss, low insertion loss, and high band‐to‐band isolation can be observed, and the proposed FSCSLSIR dual‐band BPF has an ultrawide stopband from 5.79 to 36 GHz. The experimental results are in good agreement with the simulations. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:427–435, 2015.     

Compact planar substrate‐integrated waveguide diplexers with wide‐stopband characteristics

Compact planar substrate‐integrated waveguide (SIW) diplexers with wide‐stopband characteristics are presented for the first time based on collaborative multispurious mode suppression techniques including the harmonic staggered technique, centered coupling windows, and offset‐centered output ports. The coupling scheme using common dual‐mode resonator coupled with multiple single‐mode resonators is adopted here to eliminate the T‐junctions for size and loss reduction, and the dual‐mode coupling controlling technique we previously proposed is also employed to allocate the fractional bandwidths (FBWs) of the two channels flexibly based on the FBW design graph. Additionally, by combining the harmonic staggered technique, centered coupling windows, and offset‐centered output ports, good out‐of‐band rejections can be achieved and excellent wide‐stopband characteristics have been implemented intrinsically. Two prototypes including second‐order and third‐order SIW diplexers are synthesized, designed, fabricated, and tested as demonstrations, extending the stopbands to 1.78f₁ and 2.04f₁ with the rejection levels better than 17.5 and 20 dB, respectively.