用于计算机总线并行互连的高速光互连链路

设计和实现了基于计算机ＰＣＩ总线的高速光互连链路。链路的网络接口卡具有３２位并行输入／输出接口,中间采用时分复用同步传输技术,在一根光纤中实现了ＰＣＩ总线数据的虚拟并行传输。链路的最高数据传输速率为１２５０Ｍｂｉｔ／ｓ,使用多模光纤时最大传输距离为６４０ｍ,在１０米传输距离时,通信延迟低于２００ｎｓ。     

Multi-Gigabit CO-OFDM System over SMF and MMF Links for 5G URLLC Backhaul Network

The 5G cellular network aims at providing three major services: Massive machine-type communication (mMTC), ultra-reliable low-latency communications (URLLC), and enhanced-mobile-broadband (eMBB). Among these services, the URLLC and eMBB require strict end-to-end latency of 1 ms while maintaining 99.999% reliability, and availability of extremely high data rates for the users, respectively. One of the critical challenges in meeting these requirements is to upgrade the existing optical fiber backhaul network interconnecting the base stations with a multigigabit capacity, low latency and very high reliability system. To address this issue, we have numerically analyzed 100 Gbit/s coherent optical orthogonal frequency division multiplexing (CO-OFDM) transmission performance over 400 km single-mode fiber (SMF) and 100 km of multi-mode fiber (MMF) links. The system is simulated over optically repeated and non-repeated SMF and MMF links. Coherent transmission is used, and the system is analyzed in a linear and non-linear regime. The system performance is quantified by bit error ratio (BER). Spectrally efficient and optimal transmission performance is achieved for 400 km SMF and 100 km MMF link. The results designate that MMF links can be employed beyond short reach applications by using them in the existing SMF infrastructure for long haul transmission. In particular, the proposed CO-OFDM system can be efficiently employed in 5G backhaul network. The multi-gigabit capacity and lower BER of the proposed system makes it a suitable candidate especially for the eMBB and URLLC requirements for 5G backhaul network.     

Feasibility study of a scalable optical interconnection network for massively parallel processing systems

The theoretical modeling of a novel topology for scalable optical interconnection networks, called optical multimesh hypercube (OMMH), is developed to predict size, bit rate, bit-error rate, power budget, noise, efficiency, interconnect distance, pixel density, and misalignment sensitivity. The numerical predictions are validated with experimental data from commercially available products to assess the effects of various thermal, system, and geometric parameters on the behavior of the sample model. OMMH is a scalable network architecture that combines positive features of the hypercube (small diameter, regular, symmetric, and fault tolerant) and the mesh (constant node degree and size scalability). The OMMH is implemented by a free-space imaging system incorporated with a space-invariant hologram for the hypercube links and fiber optics to provide the mesh connectivity. The results of this work show that the free-space links can operate at 368 Mbits/s and the fiber-based links at 228 Mbits/s for a bit-error rate of 10(-17) per channel. The predicted system size for 32 nodes in the OMMH is 4.16 mm × 4.16 mm × 3.38 cm. Using 16-bit, bit-parallel transmission per node, the system can operate at a bit rate of up to 5.88 Gbits/s for a size of 1.04 cm × 1.04 cm × 3.38 cm.     

The validation of hydrocodes for orbital debris impact simulation

Orbital debris pose a danger for spacecraft in orbit. Protection against this threat is obtained by shielding. One or more shields placed at some distance from the structure to be protected can minimize the damage inflicted by projectiles at high velocity. The range of velocity between 0 and 8 km/s is well covered by tests. Unfortunately, the average velocity of debris in low earth orbit is above 10 km/s with a maximum velocity around 15 km/s. The methodology presented in this paper aims to validate the numerical approach. It will predict and extrapolate the behavior of multishock shields in the velocity range between 8 and 15km/s. The formation and propagation of the debris cloud, after perforation of the shields and the generation of damage in the backwall, are key factors. These phenomena are examined, discussed and illustrated with correlation between numerical simulation with EFHYD^TM analytical formulae and test results.     

Simple Time and Frequency Dissemination Method Using Optical Fiber Network

This paper describes a simple and cost-effective method of frequency dissemination. In current digital communication networks, node clocks are hierarchically synchronized to the atomic master clock through fiber links. This synchronized network is used as an intermediate link for remote calibration services like the global positioning system common-view method. A prototype reference signal generator has been developed for recovering the communication clock signal and synthesizing a 10-MHz signal from it. The generator output frequency at the client site can be traced to coordinated universal time (UTC) National Metrology Institute of Japan (NMIJ) with some uncertainty, depending on the stability of the node clocks and the distance from the master clock. The stability performance of the generated reference signal has been tested at Okinawa-the farthest prefecture from Tokyo, where the master clock is located (baseline distance of 1500 km). The primary rate (1.544 MHz) for telecommunication services was chosen for the 10-MHz signal generation in the experiment. A sinusoidal phase fluctuation within a one-day period is dominantly observed. This fluctuation is mainly caused by fiber expansion and contraction due to normal daily temperature changes. It degrades the stability (Allan deviation) to the level of 5 X 10^-13 (t = 40 000 s, which is almost half a day). However, the major part of the phase fluctuation can be canceled by averaging a full day's data. In this case, the Allan deviation becomes 1 X 10^-13, which is obtained at Okinawa over ten consecutive days of measurement. The worst average frequency offset relative to UTC (NMIJ) (one-day averaging) is -6.3 X 10^-13. The results indicate that this method promises to be suitable for most applications, providing an uncertainty of less than 1 X 10^-12 at an averaging time of one day.     

Long-haul dense wavelength division multiplexing between a chaotic optical secure channel and a conventional fiber-optic channel

The purpose of this paper is to numerically investigate dense wavelength division multiplexing (DWDM) transmission between a chaotic optical secure channel and a conventional fiber-optic channel. A 2.5 Gbits/s secure message masked by the chaotic optical secure channel and a 10 Gbits/s message sequence carried by the conventional fiber-optic channel can be realized simultaneously when the channel spacing is 0.8?nm. The results show that the Q-factors of the recovered messages can be increased significantly when the launched optical power is reduced appropriately. The deterioration of the quality of communication caused by fiber dispersion can be compensated noticeably on the condition that the symmetrical dispersion compensation scheme is adopted. In addition, the secure message is masked by chaos shift keying in the chaotic optical secure channel. The multiplexing distance between the chaotic optical secure channel and the conventional fiber-optic channel is up to 500?km.     

Wide-range sounding of free-tropospheric water vapor with a differential-absorption lidar (DIAL) at a high-altitude station

A differential absorption lidar (DIAL) system has been developed for the measurement of water vapor throughout the free troposphere [3 to 12 km above sea level (asl.)] with high vertical resolution varied from 50 m next to the ground to 300 m above an altitude of 10 km. The system was installed at the Schneefernerhaus high-altitude research station (2675 m asl., Zugspitze, Germany). The DIAL system is based on a tunable single-mode laser system with a high pulse energy of currently 250 mJ and a repetition rate of 20 s(-1). For lidar operation with energies typically between 100 mJ and 150 mJ and an integration time of 1000 s (10000 laser shots for both DIAL wavelengths) a vertical range of at least 10 km has been demonstrated even under dry conditions and during daytime, while daytime measurements up to 12 km have been possible under humid conditions. The system was intercompared with radiosondes, which suggests an agreement within 5% in a major part of the operating range. Further improvements are planned in the upper troposphere to approach the accuracy requirements needed in climate research.     

Lensed fiber probes designed as an alternative to bulk probes in optical coherence tomography

We demonstrate a compact all-fiber sampling probe for an optical coherence tomography (OCT) system. By forming a focusing lens directly on the tip of an optical fiber, a compact sampling probe could be implemented. To simultaneously achieve a sufficiently long working distance and a good lateral resolution, we employed a large-mode area photonic crystal fiber (PCF) and a coreless silica fiber (CSF) of the same diameters. A working distance of up to 1270 microm, a 3 dB distance range of 2210 microm, and a transverse resolution of 14.2 microm were achieved with the implemented PCF lensed fiber; these values are comparable to those obtainable with a conventional objective lens having an NA of 0.25 (10 x). The performance of the OCT system equipped with the proposed PCF lensed fiber is presented by showing the OCT images of a rat finger as a biological sample and a pearl as an in-depth sample.     

Time Transfer by Passive Listening Over a 10-Gb/s Optical Fiber

A technique for time and frequency transfer over an asynchronous fiber optical transmission control protocol (TCP)/IP network is being developed in Sweden by SP Measurement Technology together with STUPI. The technique is based on passive listening to existing data traffic at 10 Gb/s in the network. Since the network is asynchronous, intermediate supporting clocks will be located and compared at each router. We detect, with a specially designed high-speed optoelectronic device, a header recognizer, the frame alignment bytes of the synchronous optical network (SONET)/synchronous digital hierarchy (SDH) protocol, as a reference for the supporting clock comparison. The goal of the project is to establish a time transfer system with an accuracy on the nanosecond level. In this paper, we present the results of a time transfer over a distance of 5 km. We have compared two clocks: a cesium clock at the Swedish National Laboratory for time and frequency and a remote rubidium clock. The results of the time transfer with the fiber link have been simultaneously compared to measurements with a Global Positioning System (GPS) carrier phase link in terms of precision and stability. The root-mean-square (rms) difference between the time difference measured with the fiber link and the GPS link is approximately 300 ps. A large part of the difference is due to the heating of the GPS antenna cable, which introduces daily delay variations on the order of 1 ns from peak to peak. For one of the days with small day-to-day variations in temperature, the corresponding rms difference is 72 ps, and the Allan deviation is below 30 ps for averaging times longer than 5 min.     

Wide‐Range Tunable Dynamic Property of Carbon‐Nanotube‐Based Fibers

A carbon nanotube (CNT) fiber is formed by assembling millions of individual tubes. The assembly feature provides the fiber with rich interface structures and thus various ways of energy dissipation, as reflected by the nonzero loss tangent (>0.028–0.045) at low vibration frequencies. A fiber containing entangled CNTs possesses higher loss tangents than a fiber spun from aligned CNTs. Liquid densification and polymer infiltration, the two common ways to increase the interfacial friction and thus the fiber's tensile strength and modulus, are found to efficiently reduce the damping coefficient. This is because the sliding tendency between CNT bundles can also be well suppressed by a high packing density and the formation of covalent polymer cross‐links within the fiber. The CNT/bismaleimide composite fiber exhibits the smallest loss tangent, nearly the same as that of carbon fibers. At a higher level of the assembly structure, namely a multi‐ply CNT yarn, the interfiber friction and sliding tendency obviously influence the yarn's damping performance, and the loss tangent can be tuned within a wide range, similar to carbon fibers, nylon yarns, or cotton yarns. The wide‐range tunable dynamic properties allow new applications ranging from high quality factor materials to dissipative systems.     

Polarized polymer films as electronic pulse detectors of cosmic dust particles

A dust particle detector based on a new physical principle of detection is described. The basic detecting element requires no bias voltage and consists of a thin film of the polarized polymer polyvinylidene fluoride (PVDF) having conducting electrodes on each of its surfaces. A high velocity (～10 km/s range) dust particle entering the detector removes dipoles along its trajectory. This produces a local depolarization, which results in a fast (ns range) charge pulse signal in the external circuit which is detected using pulse electronics. A theory has been developed for this new mechanism of pulse detection. The dependence of signal amplitude on particle mass and velocity has been measured for several PVDF detectors having thickness in the range 2–28 μm and area in the range 4–150 cm² using iron particles with velocity in the range ～1–12 km/s and mass in the range ～ 10^?13–10^?10 g. In addition, measurements carried out using a two-detector arrangement show that time of flight information may be obtained. Experimental results are presented which show, for example, that PVDF detectors have mass detection thresholds in the range ～10^?14–10^?12 g, at an impact velocity of 10 km/s, which compare favorably with mass thresholds reported for current dust detectors based on other physical principles. PVDF detectors have the advantages of being inexpensively and easily fabricated, tough, flexible and radiation resistant (to at least 10⁷ rad). They exhibit long term stability, and may be operated for extended periods of time over the temperature range ?50°C to + 50°C. In addition, their fast response permits a detector-pulse electronics system to count dust impacts at event rates up to 10⁴ s^?1 with no corrections required, and they have a response to dust particle impacts which is unaffected by high background fluxes of charged particles. As an example of the application of PVDF dust detectors, a detector is described which is being carried on space probes to measure the mass and flux of dust particles from Halley's Comet in March 1986. Other important applications for experiments in space are discussed.     

铝双层板结构撞击损伤的板间距效应实验研究

为了研究空间碎片对航天器防护结构的超高速撞击损伤特性,采用二级轻气炮发射球形弹丸,对铝双层板结构进行了超高速撞击实验研究.弹丸直径为3.97 mm,撞击速度分别为(2.58±0.08)km/s、(3.54±0.25)km/s和(4.35±0.11)km/s,板间距为10~100 mm.实验得到了铝双层板结构在不同撞击速度区间的后板损伤模式.结果表明,弹丸撞击速度一定时,后板弹坑分布随前后板间距的不同而不同.前板背面返溅影响区和后板弹坑分布区随板间距的增大而增大,各弹坑分布区扩散角随板间距的增大而减小.     

10Gbit/s色散补偿系统中自相位调制效应的研究

首先讨论了单模光纤中自相位调制对系统色散的影响。数值计算和实验结果表明。增加入纤功率能在一定程度上抑制色散效应 ,当入纤功率为 1 5dBm时 ,对于 4 0 .0km的单模光纤 ,自相位调制效应和色散恰好抵消 ,功率代价接近为零。然后比较了前、后置色散补偿系统的性能。理论分析和实验表明 ,在入纤光功率较大的情况下 ,采取前置、完全色散补偿系统具有较低的误码率。前置补偿最佳入纤功率比后置补偿最佳入纤功率高约 1 0 .0dB。这表明 ,采取前置、完全色散补偿 ,系统具有较长的中继距离和较高的接收端光信噪比 ,对 (1 6 0× 1 0Gbit/s)DWDM系统 30 0 0km超长距离传输中光放大和色散补偿问题的整体优化具有重要现实意义。     

Fluorescence decay characteristic of Tm-doped YAG crystal fiber for sensor applications, investigated from room temperature to 1400/spl deg/C

An yttrium aluminum garnet (YAG) crystal fiber with a thulium-doped end tip was specially grown by means of the laser heated pedestal growth approach and designed to be incorporated in a fiber-optic temperature probe. The fluorescence decay characteristics of the crystal fiber, including the temperature dependence of both the fluorescence lifetime and intensity, were comprehensively investigated. Experimental results indicated that the crystal fiber showed a monotonic relationship between the fluorescence lifetime and temperature with an average lifetime sensitivity of 3 /spl mu/s /spl deg/C over a wide temperature range, taking measurement from room temperature to 1200/spl deg/C. Good stability (up to 1400/spl deg/C) was observed with high repeatability of the fluorescence lifetime during the annealing process carried out on the fiber over this temperature range. The fiber was found to be an excellent candidate material to be used as a fluorescence decay-based fiber thermometer probe and the results are presented on its performance.     

Future Performance of Ground-Based and Airborne Water-Vapor Differential Absorption Lidar. II. Simulations of the Precision of a Near-Infrared, High-Power System

Taking into account Poisson, background, amplifier, and speckle noise, we can simulate the precision of water-vapor measurements by using a 10-W average-power differential absorption lidar (DIAL) system. This system is currently under development at Hohenheim University, Germany, and at the American National Center for Atmospheric Research. For operation in the 940-nm region, a large set of measurement situations is described, including configurations that are considered for the first time to the authors' knowledge. They include ultrahigh-resolution measurements in the surface layer (resolutions, 1.5 m and 0.1 s) and vertically pointing measurements (resolutions, 30 m and 1 s) from the ground to 2 km in the atmospheric boundary layer. Even during daytime, the DIAL system will have a measurement range from the ground to the upper troposphere (300 m, 10 min) that can be extended from a mountain site to the lower stratosphere. From the ground, for the first time of which the authors are aware, three-dimensional fields of water vapor in the boundary layer can be investigated within a range of the order of 15 km and with an averaging time of 10 min. From an aircraft, measurements of the atmospheric boundary layer (60 m, 1 s) can be performed from a height of 4 km to the ground. At higher altitudes, up to 18 km, water-vapor profiles can still be obtained from aircraft height level to the ground. When it is being flown either in the free troposphere or in the stratosphere, the system will measure horizontal water-vapor profiles up to 12 km. We are not aware of another remote-sensing technique that provides, simultaneously, such high resolution and accuracy.     

Microwave tunable dispersion compensator for optical fiber systems

A tunable device based on chirped microstrip delay lines is proposed to precompensate at the transmitter; the chromatic dispersion accumulated during optical fiber propagation. Compensated dispersion is finely tuned by changing the effective dielectric constant of the microstrip line by means of moving dielectric perturbers. Compensation up to 51 ps/GHz necessary to propagate over 400 km uncompensated standard single-mode fiber at 10 Gb/s is demonstrated. The proposed solution does not require coherent detection and can find application in metropolitan and regional area networks, where the physical path traced by each channel can change owing to the traffic routing, requiring the dynamic compensation of different amounts of accumulated dispersion.     

Searching for momentum enhancement in hypervelocity impacts

In conjunction with the Los Alamos National Laboratory hypervelocity microparticle impact (HMI) team effort to produce higher impact velocities and to understand the physics of crater formation and momentum transfer, we have implemented a low noise microphone as a momentum detector on both the 6 MV Van de Graaff and 85 KV “test stand” particle accelerators. Calculations are presented showing that the impulse response of a circular membrane. When used as a momentum impulse detector, the microphone theoretically may detect impulses as small as 8.8 × 10⁻¹⁵ N s. Sensitivity of the microphone in this application is limited by the noise threshold of the electronic amplifiers and the ambient microphonic vibration of the system. Calculations lead us to anticipate detection of particles over the full range of the Van de Graaff acceleration capability and up to 7 km/s on the test stand. We present momentum enhancement data in the velocity range between 10 km/s and 20 km/s. Preliminary work is presented on momentum impulse calibration of the microphone using laser-pulse photon momentum as an impulse source.     

Fiber designs with significantly reduced nonlinearity for very long distance transmission

A class of low-nonlinearity dispersion-shifted fibers based on depressed-core multistep index profiles is investigated. A systematic approach for designing these fibers in which a reference W-index profile is used to initiate the design ispresented. Transmission properties, including effective area, mode-field diameter, dispersion, dispersion slope, and cutoff wavelength, are evaluated for several design examples. The effects of varying fiber dimensions and indices on effective area and mode-field diameter are assessed. It is shown that there is a trade-off between these two properties and, generally, larger effective areas are associated with larger mode-field diameters. Dispersion-shifted single-mode fiber designs with effective areas of from 78 to 210 mum(2) and the corresponding mode-field diameter of from 8.94 to 14.94 mum, dispersion less than 0.07 ps/nm km, and dispersion slope of approximately 0.05 ps/nm(2) km are presented.     

Optische Schnittstellen

Optical interfaces: Viewing into the vacuum The requirements concerning in‐vacuum process diagnostics are more and more challenging. On the one hand, the setup itself has to be decoupled from the process to avoid any external impact on the process. On the other hand, the process parameters have to be in‐situ characterized and controlled by an in‐vacuum monitoring system. In the vicinity of these two contradictive requirements optical fiber applications gain more and more impact, since optical fibers cover several advantages: high transmission signal, inherent immunity against external electromagnetic forces, high durability and high mechanical as well as optical flexibility. The focus of the contribution is a new in‐vacuum optical temperature sensor combined with high‐temperature fiber optical feedthroughs. The sensor based on fiber Bragg gratings (FBG) in the optical fiber, which are extremely sensitive to temperature variations. In a first case study, the application of FBG with the feedthrough as an in‐vacuum optical temperature sensor is demonstrated. Thus an optical fiber containing a bunch of several FBG becomes a compact, robust, and flexible in‐vacuum network of local temperature sensors. Each individual sensor captures temperature variations over a signal path that is several km long with a remarkable accuracy up to 0.1 K and with speed of light.     

Noise performance of high-speed radio over fiber links employing vertical-cavity surface-emitting lasers

This study investigates the intensity noise in high-speed vertical-cavity surface-emitting lasers (VCSELs) and its contribution to the noise performance of radio over fiber (RoF) links. We evaluate the sinusoidal modulation of VCSELs in terms of the second-order harmonic distortion (2HD) and third-order intermodulation distortion (IMD3) in additions to the relative intensity noise (RIN). The spurious-free dynamic range of the proposed VCSEL is estimated. The noise performance of the RoF link is assessed by the noise figure. The modulation characteristics of the VCSEL and the gain and noise factor (NF) of the fiber link are compared under conventional and high-speed modulations of VCSELs. Also, we present comparison of the NF between short (300 m) and relatively long (2 km) fibers.