共查询到20条相似文献,搜索用时 281 毫秒
1.
均匀沉淀法合成纳米钛酸锌及其形态结构分析 总被引:2,自引:0,他引:2
以四氯化钛、硫酸锌为原料,以尿素为沉淀剂,用均匀沉淀法合成纳米钛酸锌粉体,研究了合成条件及烧结过程,确定了合理的工艺线路和工艺参数,并利用XRD,TEM,DTA-TG,UV-VIS等手段分别对复合材料钛酸锌的形态、粒径、紫外一可见光吸收等性能进行了表征。结果表明:复合材料钛酸锌的粒子均为球形,尺寸约为20nm,粒径分布较均匀,颗粒团聚现象少,在波长400~600nm的可见光区有明显吸收。 相似文献
2.
沉淀溶出法制备纳米钛酸锌粉体 总被引:7,自引:0,他引:7
就纳米钛酸锌(ZnTiO3)粉体的沉淀溶出法制备条件进行了探讨,发现在600℃煅烧1h,即可制得氧化锌-钛酸锌复合粉体,其粒径20~50nm;将复合粉体中过剩的氧化锌溶出,继续在700℃于马弗炉内煅烧1h.能得到晶型较好的白色球状钛酸锌粉体,粒径约30~60nm。 相似文献
3.
《中国陶瓷》2015,(10)
利用溶胶-凝胶法(sol-gel)分别制备了稀土铕掺杂钛酸锌和镨掺杂钛酸锌粉体,通过X射线衍射仪(XRD)、傅里叶变换红外光谱仪(FT-IR)、透射电子显微镜(TEM)以及荧光分光光度计(PL)对样品的结构、形貌及发光性能进行了表征。结果表明,Eu3+掺杂钛酸锌呈六方相偏钛酸锌,而Pr3+掺杂钛酸锌呈现六方相偏钛酸锌和立方相正钛酸锌。荧光分析表明,Eu3+浓度在0~3.0%研究范围内,其发光强度随Eu3+浓度的增加先增强后降低,最大发光强度为1.5%;Pr3+浓度在0~0.5%研究范围内,其发光强度随Pr3+浓度的增加先增强后降低,最大发光强度为0.3%,且Eu3+掺杂钛酸锌的红光发射强度远比Pr3+大。研究表明铕掺杂钛酸锌荧光粉可作为一种潜在的白光LED用红色荧光粉。 相似文献
4.
5.
6.
7.
苯并三唑类光稳定剂的合成及应用 总被引:8,自引:0,他引:8
本文综述了对苯并三唑类光稳定剂的合成技术及应用情况。对生产工艺中各种还原方法(锌
粉法、水合肼法、硫化钠-锌粉法等)进行了分析对比,指出硫化钠-锌粉法是一种适于工业化的还原方法。列举了对该类光稳定剂在聚氯乙烯、聚乙烯、聚丙烯,聚碳酸酯、聚氨酯树脂等方面的应用。 相似文献
8.
9.
低温固相反应合成锡酸锌 总被引:3,自引:0,他引:3
以氯化锡、硝酸锌、氢氧化钠为原料,用低温固相反应法合成尖晶石型复合氧化物锡酸锌晶体.用红外光谱表征产物的晶体结构,结果表明:固相反应完全,合成的前躯体经600 ℃煅烧2 h后可以得到单相的锡酸锌粉体.该方法不仅降低了锡酸锌物相形成的温度,也符合材料合成化学绿色化的要求,而且有效避免了液相法团聚、操作过程烦琐的缺点.具有设备简单、计量比易于控制、所需反应温度低的优点.为此类材料的合成提出了一种廉价、简单的方法. 相似文献
10.
以甲基丙烯酸、氢氧化钠、氯化锌、氨水等为主要原料,采用化学沉淀法在室温下合成了晶粒尺寸只有几十纳米的甲基丙烯酸锌粉体(ZMA);以FTIR,XRD,NMR,TEM等分析方法对粉体进行了表征,确认了产物的结构及其所属晶系;将合成产物与美国产SR-634甲基丙烯酸锌进行了性能比较,合成产物的平均粒径为40.6 nm,接近于后者的31.4 nm;讨论了氯化锌溶液的滴加速率、ZMA浓度、搅拌速率等因素对合成的甲基丙烯酸锌粉体粒径的影响;得到最优化实验条件为:氯化锌溶液的滴加速率0.5 mL/m in,ZMA浓度4.2 mol/L,搅拌速率100 r/m in,在此条件下,甲基丙烯酸锌收率达80.4%。 相似文献
11.
晶须作为一种增强材料,由于其优良的性能,使得晶须增强复合材料已成为复合材料领域中的一个重要分支。本文介绍了一些常用晶须,综述了氧化锌、钛酸钾、硼酸铝等新型陶瓷晶须的制备方法、显微结构以及性能与应用。 相似文献
12.
13.
钛酸铅系电子陶瓷及粉体的制备方法 总被引:3,自引:1,他引:2
综述了钛酸铅系电子陶瓷及粉体的制备方法,主要讨论了水热法和溶胶一凝胶法的制备原理及影响产物性能的因素。为钛酸铅系功能陶瓷及材料的研究指明了方向。即用最新方法制备超纯、超细粉体,以先进技术指导合成降低反应温度并制备出功能复合材料。 相似文献
14.
15.
16.
17.
18.
Juanjuan Wang Guangzhao Li Xiaolian Chao Lajun Feng 《Polymer-Plastics Technology and Engineering》2017,56(11):1196-1202
Composites with damping–absorption performance and storage-loss behavior based on carbon nanotubes as a modifier and zinc titanate/room temperature vulcanized silicone rubbers as a matrix were fabricated by a reactive solution mixing process, wet ball milling, and the three-roller milling method. The microstructures, chemical structures, and morphologies of the composites were characterized by scanning electron microscopy, infrared spectroscopy, and X-ray diffraction. The thermal stabilities were investigated by thermogravimetric analysis. The effect of carbon nanotubes on the comprehensive performance of the carbon nanotube/zinc titanate/room temperature vulcanized silicon rubber composites was investigated. It was found that doping with carbon nanotubes can improve the comprehensive performance of the zinc titanate/room temperature vulcanized silicon rubber complex matrix. The best comprehensive properties were d33?=?72 pC/N, storage modulus?=?4,100?MPa, loss modulus?=?400?MPa, damping coefficient?=?0.23, and absorption coefficients?=?0.4–0.6 for 4?wt% carbon nanotube/zinc titanate/room temperature vulcanized silicon rubber. In addition, the lattice parameters of zinc titanate were found to be highly dependent on the carbon nanotube content, and the absorption and damping performance of the composites were dependent on the frequency and temperature. 相似文献
19.
前景广阔的锌基高温脱硫剂 总被引:2,自引:0,他引:2
本文详述了以氧化锌为主的锌基高温脱硫剂(包括ZnO、ZnFe2O4、Zn2TiO4等),并介绍了各国在新型发电技术方面应用锌基脱硫剂的状况及我国在这方面的发展状况。 相似文献
20.
Ramakrishnan Ramaseshan Seeram Ramakrishna 《Journal of the American Ceramic Society》2007,90(6):1836-1842
Fabrication of a novel ceramic nanofiber system viz. zinc titanate using the well-known electrospinning technology with polyvinylpyrrolidone as a binder is reported. Use of zinc titanates as reactive sorbents to detoxify chemical warfare agents is hypothesized and proved. The zinc titanate nanofibers are tested against simulants of nerve and mustard agents and show satisfactory destructive activity. The extent of detoxification is measured using GC-MS analysis. The products of reaction of zinc titanate against the simulants are identified and are found to be relatively harmless. The possibility of replacement of conventional-activated carbon by electrospun ceramic nanofibers for face masks and protective clothing is proposed. 相似文献