High-Efficiency Perovskite Quantum Dot Photovoltaic with Homogeneous Structure and Energy Landscape

The energy disorder originating from quantum dot (QD) size and relevant solid film inhomogeneity is detrimental to the charge transport and efficiency of QD based solar cells. The emergence of halide perovskite QDs (PQDs) have attracted great attention as promising absorbers in QD photovoltaics. However, it is currently difficult in preparing structural uniform PQD film with homogenous energetic landscape, which is essential for highly reproducible and efficient solar cells. Herein, assisted by a bidentate ligand 2,5-thiophenedicarboxylic acid, a facile solution phase anchoring (SPA) strategy is first reported for design and preparation of all-inorganic CsPbI₃ PQD film with reduced structure and energy disorder. The SPA can enhance PQD dispersion as well as dot-to-dot interaction, which is beneficial for fabricating high-quality PQD arrays and photovoltaic devices. The engineered CsPbI₃ PQD solar cell exhibits enhanced reproducibility, and higher open–circuit voltage together with a champion efficiency of 16.14%, which is among the highest report to date. These results are believed to provide design principle of uniform PQDs for high-performance optoelectronic application.     

Ambient Stable and Efficient Monolithic Tandem Perovskite/PbS Quantum Dots Solar Cells via Surface Passivation and Light Management Strategies

Here, highly efficient and stable monolithic (2-terminal (2T)) perovskite/PbS quantum dots (QDs) tandem solar cells are reported, where the perovskite solar cell (PSC) acts as the front cell and the PbS QDs device with a narrow bandgap acts as the back cell. Specifically, ZnO nanowires (NWs) passivated by SnO₂ are employed as an electron transporting layer for PSC front cell, leading to a single cell PSC with maximum power conversion efficiency (PCE) of 22.15%, which is the most efficient NWs-based PSCs in the literature. By surface passivation of PbS QDs by CdCl₂, QD devices with an improved open-circuit voltage and a PCE of 8.46% (bandgap of QDs: 0.92 eV) are achieved. After proper optimization, 2T and 4T tandem devices with stabilized PCEs of 17.1% and 21.1% are achieved, respectively, where the 2T tandem device shows the highest efficiency reported in the literature for this design. Interestingly, the 2T tandem cell shows excellent operational stability over 500 h under continuous illumination with only 6% PCE loss. More importantly, this device without any packaging depicts impressive ambient stability (almost no change) after 70 days in an environment with controlled 65% relative humidity, thanks to the superior air stability of the PbS QDs.     

Reversible Photoinduced Phase Segregation and Origin of Long Carrier Lifetime in Mixed‐Halide Perovskite Films

Mixed‐halide hybrid perovskite semiconductors have attracted tremendous attention as a promising candidate for efficient photovoltaic and light‐emitting devices. However, these perovskite materials may undergo phase segregation under light illumination, thus affecting their optoelectronic properties. Here, photoexcitation induced phase segregation in triple‐cation mixed‐halide perovskite films that yields to red‐shift in the photoluminescence response is reported. It is demonstrated that photoexcitation induced halide migration leads to the formation of smaller bandgap iodide‐rich and larger bandgap bromide‐rich domains in the perovskite film, where the phase segregation rate is found to follow the excitation power‐density as a power law. Results confirm that charge carrier lifetime increases due to the trapping of photoexcited carriers in the segregated smaller bandgap iodide‐rich domains. Interestingly, these photoinduced changes are fully reversible and thermally activated when the excitation power is turned off. A significant difference in activation energies for halide ion migration is observed during phase segregation and recovery process. Additionally, the emission linewidth broadening is investigated as a function of temperature which is governed by the exciton–optical phonon coupling. The mechanism of photoinduced phase segregation is interpreted based on exciton–phonon coupling strength in both mixed and demixed (segregated) states of perovskite films.     

Interface Engineering by Thiazolium Iodide Passivation Towards Reduced Thermal Diffusion and Performance Improvement in Perovskite Solar Cells

Interface engineering has become one of the most facile and effective approaches to improve solar cells performance and its long‐term stability and to retard unwanted side reactions. Three passivating agents are developed which can functionalize the surface and induce hydrophobicity, by employing substituted thiazolium iodide (TMI) for perovskite solar cells fabrication. The role of TMI interfacial layers in microstructure and electro‐optical properties is assessed for structural as well as transient absorption measurements. TMI treatment resulted in V_OC and fill factor enhancement by reducing possible recombination paths at the perovskite/hole selective interface and by reducing the shallow as well as deep traps. These in turn allow to achieve higher performance as compared to the pristine surface. Additionally, the TMI passivated perovskite layer considerably reduces CH₃NH₃⁺ thermal diffusion and degradation induced by humidity. The un‐encapsulated perovskite solar cells employing TMI exhibit a remarkable stability under moisture levels (≈50% RH), retaining ≈95% of the initial photon current efficiency after 800 h of fabrication, paving the way towards a potential scalable endeavor.     

Band Engineering via Gradient Molecular Dopants for CsFA Perovskite Solar Cells

Perovskites with the multi-cation composition of cesium (Cs), methylammonium (MA), and formamidinium (FA) (CsMAFA) are pursued for their high power conversion efficiencies, but they are limited by their thermal stability. To withstand damp-heat accelerated aging MA-free compositions such as CsFA are of interest, but these exhibit lower carrier diffusion lengths and thus lesser performance in photovoltaic devices. A band engineering strategy that overcomes limited carrier diffusion within inverted perovskite solar cells based on CsFA is reported. A joint experimental-computational study shows that treating the perovskite with an n-type molecular dopant increases band bending, shaping the electric field across the active layer to overcome limited diffusive transport. Using this strategy, CsFA solar cell devices with stabilized power conversion efficiencies of 20.3%, a high value for devices using CsFA active layers, are fabricated.     

Modulation on Electrostatic Potential of Passivator for Highly Efficient and Stable Perovskite Solar Cells

The perovskite layer contains a large number of charged defects that seriously impair the efficiency and stability of perovskite solar cells (PSCs), thus it is essential to develop an effective passivation strategy to heal them. Based on theoretical calculations, it is found that enhancing the electrostatic potential of passivators can improve passivation effect and adsorption energy between charged defects and passivators. Herein, an electrostatic potential modulation (EPM) strategy is developed to design passivators for highly efficient and stable PSCs. With the EPM strategy, 1-phenylethylbiguanide (PEBG) and 1-phenylbiguanide (PBG) are designed. It is found that the charge distribution and electrostatic potential of phenyl- and phenylethyl- substituent on the biguanide are significantly enhanced. The N atom directly bonding to the phenyl group shows larger positive charge than that bonding to the phenylethyl group. The modulated electrostatic potential makes PBG bind stronger with the defects on perovskite surface. Based on the effective passivation of EPM, a champion efficiency of 24.67% is realized and the device retain 91.5% of its initial PCE after ≈1300 h. The promising EPM strategy, which provides a principle of passivator design and allows passivation to be controllable, may advance further optimization and application of perovskite solar cells toward commercialization.     

A Simple Way to Simultaneously Release the Interface Stress and Realize the Inner Encapsulation for Highly Efficient and Stable Perovskite Solar Cells

The mixed halide perovskites have become famous for their outstanding photoelectric conversion efficiency among new‐generation solar cells. Unfortunately, for perovskites, little effort is focused on stress engineering, which should be emphasized for highly efficient solar cells like GaAs. Herein, polystyrene (PS) is introduced into the perovskite solar cells as the buffer layer between the SnO₂ and perovskite, which can release the residual stress in the perovskite during annealing because of its low glass transition temperature. The stress‐free perovskite has less recombination, larger lattices, and a lower ion migration tendency, which significantly improves the cell's efficiency and device stability. Furthermore, the so‐called inner‐encapsulated perovskite solar cells are fabricated with another PS capping layer on the top of perovskite. As high as a 21.89% photoelectric conversion efficiency (PCE) with a steady‐state PCE of 21.5% is achieved, suggesting that the stress‐free cell can retain almost 97% of its initial efficiency after 5 days of “day cycle” stability testing.     

Designing Heterovalent Substitution with Antioxidant Attribute for High-Performance Sn-Pb Alloyed Perovskite Solar Cells

All-perovskite tandem solar cells are promising for breaking through the single-junction Shockley–Queisser limit, and that potentially raises interest in configuring efficient Sn-Pb alloyed narrow-bandgap perovskite solar cells (PSCs). However, the Sn-Pb alloyed perovskites are commonly plagued by uncontrollable crystallization dynamics and severe p-doping levels. Herein, an effective additive molecule is designed with heterovalent substitution and antioxidant functions, whereby an organic metal coordination compound of tris(2,4-pentanedionato)gallium (TPGa) is employed to upgrade the quality of perovskite films. Ga³⁺ substitution obviously boosts the formation energy of Sn vacancies and heals the trap states. Meanwhile, the crystal structure evolution process is improved by the anchoring effect of 2,4-pentanedionato. The PSCs incorporating these improvements deliver not only a power conversion efficiency of 21.5% but also outstanding stability, as demonstrated by retaining 80% of the initial efficiency for over 1500 h. In addition, 23.14%-efficient all-perovskite tandem solar cells are further obtained by pairing this PSC with a wide-bandgap (1.74 eV) top cell. This study supports the feasibility of doping trivalent ions into the Sn-Pb alloyed perovskites to compromise the self-p-doping effect and highlights the importance of acetylacetone for passivating defects and hindering oxidation.     

Towards Efficient Integrated Perovskite/Organic Bulk Heterojunction Solar Cells: Interfacial Energetic Requirement to Reduce Charge Carrier Recombination Losses

Integrated perovskite/organic bulk heterojunction (BHJ) solar cells have the potential to enhance the efficiency of perovskite solar cells by a simple one‐step deposition of an organic BHJ blend photoactive layer on top of the perovskite absorber. It is found that inverted structure integrated solar cells show significantly increased short‐circuit current (J_sc) gained from the complementary absorption of the organic BHJ layer compared to the reference perovskite‐only devices. However, this increase in J_sc is not directly reflected as an increase in power conversion efficiency of the devices due to a loss of fill factor. Herein, the origin of this efficiency loss is investigated. It is found that a significant energetic barrier (≈250 meV) exists at the perovskite/organic BHJ interface. This interfacial barrier prevents efficient transport of photogenerated charge carriers (holes) from the BHJ layer to the perovskite layer, leading to charge accumulation at the perovskite/BHJ interface. Such accumulation is found to cause undesirable recombination of charge carriers, lowering surface photovoltage of the photoactive layers and device efficiency via fill factor loss. The results highlight a critical role of the interfacial energetics in such integrated cells and provide useful guidelines for photoactive materials (both perovskite and organic semiconductors) required for high‐performance devices.     

A Highly Tolerant Printing for Scalable and Flexible Perovskite Solar Cells

Homogeneity and stability of flexible perovskite solar cells (PSCs) are significant for the commercial feasibility in upscaling fabrication. Concretely, the mismatching between bottom interface and perovskite precursor ink can cause uncontrollable crystallization and undesired dangling bonds during the printing process. Herein, methylammonium acetate, serving as ink assistant (IAS) can effectively avoid the micron-scale defects of perovskite film. The in situ optical microscope is applied to prove the IAS can inhibit the colloidal aggregation and induce more adequate crystallization growth, thus avoiding the micron-scale defects of pinholes and intergranular cracking. Concurrently, 4-chlorobenzenesulfonic acid is introduced into the electrode surface as a passivation layer to restore the deep traps at perovskite interface in nano-scale. Finally, the target flexible devices (1.01 cm²) deliver a superior efficiency of 18.12% with improved air atmosphere stability. This multi-scale defect repair strategy provides an integrated design concept of homogeneity and stability for scalable and flexible PSCs.     

Novel Cu Nanowires/Graphene as the Back Contact for CdTe Solar Cells

Cu‐nanowire‐doped graphene (Cu NWs/graphene) is successfully incorporated as the back contact in thin‐film CdTe solar cells. 1D, single‐crystal Cu nanowires (NWs) are prepared by a hydrothermal method at 160 °C and 3D, highly crystalline graphene is obtained by ambient‐pressure CVD at 1000 °C. The Cu NWs/graphene back contact is obtained from fully mixing the Cu nanowires and graphene with poly(vinylidene fluoride) (PVDF) and N‐methyl pyrrolidinone (NMP), and then annealing at 185 °C for solidification. The back contact possesses a high electrical conductivity of 16.7 S cm^?1 and a carrier mobility of 16.2 cm² V^?1 s^?1. The efficiency of solar cells with Cu NWs/graphene achieved is up to 12.1%, higher than that of cells with traditional back contacts using Cu‐particle‐doped graphite (10.5%) or Cu thin films (9.1%). This indicates that the Cu NWs/graphene back contact improves the hole collection ability of CdTe cells due to the percolating network, with the super‐high aspect ratio of the Cu nanowires offering enormous electrical transport routes to connect the individual graphene sheets. The cells with Cu NWs/graphene also exhibit an excellent thermal stability, because they can supply an active Cu diffusion source to form an stable intermediate layer of CuTe between the CdTe layer and the back contact.     

Metal Oxide Charge Transport Layers for Efficient and Stable Perovskite Solar Cells

Currently, the efficiency of perovskite solar cells (PSCs) is ≈24%. For the fabrication of such high efficiency PSCs, it is necessary to use both electron and hole transport layers to effectively separate the charges generated by light absorption of the perovskite layer and selectively transfer the separated electrons and holes. In addition to the efficiency, the materials used for transporting charges must be resilient to light, heat, and moisture to ensure long‐term stability of PSCs; furthermore, low‐cost fabrication is required to form a charge transport layer at low temperatures by a solution process. For this purpose, metal oxides are best suited as charge transport materials for PSCs because of their advantages such as low cost, long‐term stability, and high efficiency. In this Review, the metal oxide electron and hole transport materials used in PSCs are reviewed and preparation of these materials is summarized. Finally, the challenges and future research direction for metal oxide‐based charge transport materials are described.     

Multi-Site Intermolecular Interaction for In Situ Formation of Vertically Orientated 2D Passivation Layer in Highly Efficient Perovskite Solar Cells

Surface passivation via 2D perovskite is critical for perovskite solar cells (PSCs) to achieve remarkable performances, in which the applied spacer cations play an important role on structural templating. However, the random orientation of 2D perovskite always hinder the carrier transport. Herein, multiple nitrogen sites containing organic spacer molecule (1H-Pyrazole-1-carboxamidine hydrochloride, PAH) is introduced to form 2D passivation layer on the surface of formamidinium based (FAPbI₃) perovskite. Deriving from the interactions between PAH and PbI₂, the defects of FAPbI₃ perovskite are effectively passivated. Interestingly, due to the multiple-site interactions, the 2D nanosheets are found to grow perpendicularly to the substrate for promotion of charge transfer. Therefore, an impressive power conversion efficiency of 24.6% and outstanding long-term stability are achieved for the 2D/3D perovskite devices. The findings further provide a perspective in structure design of novel organic halide salts for the fabrication of efficient and stable PSCs.     

Reconstruction of the Indium Tin Oxide Surface Enhances the Adsorption of High-Density Self-Assembled Monolayer for Perovskite/Silicon Tandem Solar Cells

Self-assembled monolayers (SAMs) are widely used as carrier transport interlayers for enabling high-efficiency perovskite solar cells (PSCs). However, achieving uniform and pinhole-free monolayers on metal oxide (e.g., indium tin oxide, ITO) surfaces is still challenging due to the sensitivity of SAM adsorption to the complex oxide's surface chemistry. Here, the hydrofluoric acid and the subsequent UV–ozone treatment are employed to reconstruct the ITO surface by selectively removing the undesired terminal hydroxyl and hydrolysis product. This can significantly increase the ITO surface activity and area, thus facilitating the adsorption of high-density SAMs. The resultant fluorinated surface can also prevent the direct contact of ITO with the perovskite active layer and passivate the perovskite bottom interface. Benefiting from the synergistically improved perovskite film formation, charge extraction, energy level alignment, and interfacial chemical stability, the corresponding PSC achieves a greatly enhanced power conversion efficiency of 21.3%, along with an enhanced long-term stability as compared to the control counterpart. Furthermore, a semitransparent PSC with a certified efficiency of 19.0% (with a record fill factor of 84.1%) and a four-terminal perovskite/silicon tandem with an efficiency of 28.4% are also demonstrated.     

Phenylhydrazinium Iodide for Surface Passivation and Defects Suppression in Perovskite Solar Cells

In recent years, hybrid perovskite solar cells (HPSCs) have received considerable research attention due to their impressive photovoltaic performance and low‐temperature solution processing capability. However, there remain challenges related to defect passivation and enhancing the charge carrier dynamics of the perovskites, to further increase the power conversion efficiency of HPSCs. In this work, the use of a novel material, phenylhydrazinium iodide (PHAI), as an additive in MAPbI₃ perovskite for defect minimization and enhancement of the charge carrier dynamics of inverted HPSCs is reported. Incorporation of the PHAI in perovskite precursor solution facilitates controlled crystallization, higher carrier lifetime, as well as less recombination. In addition, PHAI additive treated HPSCs exhibit lower density of filled trap states (10¹⁰ cm^?2) in perovskite grain boundaries, higher charge carrier mobility (≈11 × 10^?4 cm² V^?1 s), and enhanced power conversion efficiency (≈18%) that corresponds to a ≈20% improvement in comparison to the pristine devices.     

Self‐Crystallized Multifunctional 2D Perovskite for Efficient and Stable Perovskite Solar Cells

Recently, perovskite solar cells (PSC) with high power‐conversion efficiency (PCE) and long‐term stability have been achieved by employing 2D perovskite layers on 3D perovskite light absorbers. However, in‐depth studies on the material and the interface between the two perovskite layers are still required to understand the role of the 2D perovskite in PSCs. Self‐crystallization of 2D perovskite is successfully induced by deposition of benzyl ammonium iodide (BnAI) on top of a 3D perovskite light absorber. The self‐crystallized 2D perovskite can perform a multifunctional role in facilitating hole transfer, owing to its random crystalline orientation and passivating traps in the 3D perovskite. The use of the multifunctional 2D perovskite (M2P) leads to improvement in PCE and long‐term stability of PSCs both with and without organic hole transporting material (HTM), 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenyl‐amine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) compared to the devices without the M2P.     

Surface Defects Management by In Situ Etching with Methanol for Efficient Inverted Inorganic Perovskite Solar Cells

Inorganic perovskite solar cells (IPSCs) have developed rapidly due to their good thermal stability and the bandgap suitable for perovskite/silicon tandem solar cells. However, the large open-circuit voltage (V_OC) deficit derived from the surface defects and the energy level structure mismatch impede the development of device performance, especially in the P-I-N structure IPSCs. Herein, an innovative in situ etching (ISE) treatment method is proposed to reduce surface defects through methanol without additional passivator. It is found that the perovskite films treated with methanol result in a slight excess of PbI₂ on the surface and inserted into the grain boundaries. Therefore, the successful decrease of surface defects by methanol and the passivation of grain boundary defects by PbI₂ greatly reduce the trap density of perovskite films. And the larger work function of PbI₂ contributes to the energy band of perovskite surface bending downward and forms gradient energy level alignment at the I/N interface, which accelerates extraction of charge carriers. As a result, the efficiency of CsPbI_2.85Br_0.15 inverted IPSC is enhanced from 16.00% to 19.34%, which is one of the mostly efficient IPSCs. This work provides an original idea without additional passivator to manage the defects of inorganic perovskite.     

Single Crystal Perovskite Solar Cells: Development and Perspectives

The efficiency of perovskite solar cells has increased to a certified value of 25.2% in the past 10 years, benefiting from the superior properties of metal halide perovskite materials. Compared with the widely investigated polycrystalline thin films, single crystal perovskites without grain boundaries have better optoelectronic properties, showing great potential for photovoltaics with higher efficiency and stability. Additionally, single crystal perovskite solar cells are a fantastic model system for further investigating the working principles related to the surface and grain boundaries of perovskite materials. Unfortunately, only a handful of groups have participated in the development of single crystal perovskite solar cells; thus, the development of this area lags far behind that of its polycrystalline counterpart. Therefore, a review paper that discusses the recent developments and challenges of single crystal perovskite solar cells is urgently required to provide guidelines for this emerging field. In this progress report, the optical and electrical properties of single crystal and polycrystalline perovskite thin films are compared, followed by the recent developments in the growth of single crystal perovskite thin films and the photovoltaic applications of this material. Finally, the challenges and perspectives of single crystal perovskite solar cells are discussed in detail.     

One-Source Strategy Boosting Dopant-Free Hole Transporting Layers for Highly Efficient and Stable CsPbI2Br Perovskite Solar Cells

All-inorganic perovskites have emerged as promising photovoltaic materials due to their superior thermal stability compared to their organic–inorganic hybrid counterparts. However, the inferior film quality and doped hole transport layer (HTL) have a strong tendency to degrade the perovskite under high temperatures or harsh operating conditions. To solve these problems, a one-source strategy using the same polymer donor material (PDM) to simultaneously dope CsPbI₂Br perovskite films via antisolvent engineering and fabricating the HTL is proposed. The doping assists perovskite film growth and forms a top–down gradient distribution, generating CsPbI₂Br with enlarged grain size and reduced defect density. The PDM as the HTL suppresses the energy barrier and forms favorable electrical contacts for hole extraction, and assemble into a fingerprint-like morphology that improves the conductivity, facilitating the creation of a dopant-free HTL. Based on this one-source strategy using PBDB-T as PDM, the CsPbI₂Br perovskite solar cell with a dopant-free HTL achieves a power conversion efficiency (PCE) of 16.40%, which is one of the highest PCEs reported among all-inorganic CsPbI₂Br pero-SCs with a dopant-free HTL. Importantly, the devices exhibit the highest thermal stability at 85 °C and operational stability under continuous illumination even with Ag as the top electrode and present good universality.     

Host-Guest Complexation Strategy for Passivating Pb-Dimer Related Defects in Perovskite Photovoltaics

Although there is extensive attention to the eminent perovskite solar cells, the deep-level defects such as Pb-Pb dimers in the solution-processed polycrystalline perovskites inevitably result in photovoltaic output losses and subsequent degradation. Recently, it is reported that an electron-donating group can passivate Pb dimer defects efficiently. However, the mechanism for the causation of metallic lead (Pb⁰) from the iodide vacancy (V_I) is unclear. Herein, a chain reaction mechanism is proposed for the possible transformation process from V_I to Pb⁰ with the Pb dimer intermediates. In this regard, a host-guest strategy is adopted by using 4-tert-Butyl-1-(ethoxycarbonyl- methoxy) thiacalix[4]arene (tBuTCA) to complex with the cations and out-of-cage (Lead(II) iodide) PbI₂. Moreover, a host-guest complexation can be formed due to the Pb²⁺-π interactions. Continuously, the negative charge compensation for iodine vacancy can hinder the formation of Pb-Pb dimer, thus significantly suppressing non-radiative recombination. Consequently, the resulting solar cells show more than 24% power conversion efficiencies and maintain over 96% of their initial performance without encapsulation for 486 h under an ambient environment. This work highlights the significance of supramolecular engineering in constructing a high-quality perovskite for efficient and stable perovskite solar cells.