Low-voltage low-power FGMOS based VDIBA and its application as universal filter

This paper presents Floating gate MOS (FGMOS) based low-voltage low-power variant of recently proposed active element namely Voltage Differencing Inverting Buffered Amplifier (VDIBA). The proposed configuration operates at lower supply voltage ±0.75 V with the total quiescent power consumption of 1.5 mW at the biasing current of 100 µA. Further the operating frequency of the proposed VDIBA is improved by using the resistive compensation method of bandwidth extension in Operational Transconductance Amplifier (OTA) stage of the block. By using resistive compensation method of bandwidth extension, the bandwidth of OTA stage increases from 92.47 MHz to 220.67 MHz. As an application, proposed FGMOS based VDIBA has been used to realize a novel resistorless voltage mode (VM) universal filter. The proposed universal filter configuration is capable of realizing all the standard filter functions in both inverting and non-inverting forms simultaneously without any matching constraint. Other important features include independently tunable filter parameters, cascadibility and low sensitivity figure. The proposed filter is tunable over the frequency range of 4.1 MHz to 12.9 MHz and is capable of compensating for process, voltage and temperature (PVT) variation. The simulations are performed using SPICE and TSMC 0.18 µm CMOS technology parameters with±0.75 V supply voltage to validate the effectiveness of the proposed circuit.     

0.4-V bulk-driven differential-difference amplifier

A new solution for an ultra-low-voltage, low-power, bulk-driven fully differential-difference amplifier (FDDA) is presented in the paper. Simulated performance of the overall FDDA for a 50 nm CMOS process and supply voltage of 0.4 V, shows dissipation power of 31.8 μW, the open loop voltage gain of 58.6 dB and the gain-bandwidth product (GBW) of 2.3 MHz for a 20 pF load capacitance. Despite the very low supply voltage, the FDDA exhibits rail-to-rail input/output swing. The circuit performance has also been tested in two applications; the differential voltage follower and the second-order band-pass filter, showing satisfactory accuracy and dynamic range.     

MISO current mode bi-quadratic filter employing high performance inverting second generation current conveyor circuit

This paper presents static and dynamic studies of a new CMOS realization for the inverting second generation current conveyor circuit (ICCII). The proposed design offers enhanced functionalities compared to ICCII circuits previously presented in the literature. It is characterized by a rail to rail dynamic range with high accuracy, a low parasitic resistor at terminal X (1.6 Ω) and low power consumption (0.31 mW) with wide current mode (3.32 GHz) and voltage mode (3.9 GHz) bandwidths.Furthermore, a new MISO current mode bi-quadratic filter based on using ICCII circuits as active elements is proposed. This filter can realize all standard filter responses without changing the circuit topology. It is characterized by active and passive sensitivities less than unity and an adjustment independently between pole frequency and quality factor. The operating frequency limit of this filter is about 0.8 GHz with 0.674 mW power consumption.The proposed current conveyor circuits and bi-quadratic filter are tested by TSPICE using CMOS 0.18 µm TSMC technology with ±0.8 V supply voltage to verify the theoretical results.     

Improving GBW product on CMOS operational transconductance amplifiers by interleaved feedforward paths

This paper presents two Operational Transconductance Amplifier (OTA) compensation schemes for multistage topologies. The solutions are based on interleaved feedforward paths that cancel a non-dominant pole similarly to the zero nulling resistor technique with the advantage of avoiding resistors. Both schemes are designed in 90 nm CMOS process, the first one obtains 71 dB of DC gain, a gain bandwidth product (GBW) of 720 MHz with 360 μW of power consumption. The second proposed scheme obtains a similar DC gain and doubles the former proposed OTA GBW at the expense of 2.2 mW of power consumption for high speed applications. The compensation schemes are theoretically analyzed and the design guidelines are presented. The results of post layout simulations and corner analysis validate the new solutions.     

A new CMOS differential current-mode AGC on the division operation based

A new CMOS differential current-mode AGC on the division operation based is presented. The operation principle consists in detection of both positive and negative envelopes of the differential input signal cycles, respectively. The output signal with constant magnitude is obtained by dividing the differential input signal to the difference between the positive and negative detected envelopes. The new current-mode architecture of the proposed AGC (composed only by an envelope detector and a divider stage) diminishes significantly the settling time, the circuit complexity and the power consumption. The circuit yields an input dynamic range of 15 dB and provides a constant magnitude output signal in the frequency range from 10 MHz to 70 MHz. The current consumption is 5 mA from a single 3.3 V supply voltage. The simulations performed in 0.13 µm CMOS process confirm the theoretically obtained results.     

A low-power wide tuning-range CMOS current-controlled oscillator

This paper presents a low-power, small-size, wide tuning-range, and low supply voltage CMOS current-controlled oscillator (CCO) for current converter applications. The proposed oscillator is designed and fabricated in a standard 180-nm, single-poly, six-metal CMOS technology. Experimental results show that the oscillation frequency of the CCO is tunable from 30 Hz to 970 MHz by adjusting the control current in the range of 100 fA to 10 µA, giving an overall dynamic range of over 160 dB. The operation of the circuit is nearly independent of the power supply voltage and the circuit operates at supply voltages as low as 800 mV. Also, at this voltage, with control currents in the range of sub-nano-amperes, the power consumption is about 30 nW. These features are promising in sensory and biomedical applications. The chip area is only 8.8×11.5 µm².     

Low power dissipation SiGe HBT dual-band variable gain amplifier

A dual-band variable gain amplifier operating at 0.9 GHz and 2.4 GHz was designed based on high performance RF SiGe HBT for large amount of signals transmission and analysis. Current steering was adopted in gain-control circuit to get variable trans-conductance and then variable gain. Emitter degeneration and current reuse were considered in amplifying stage for low noise figure and low power dissipation respectively. A single-path circuit resonating at two frequency points simultaneously was designed for input impedance matching. PCB layout parasitic effects, especially the via parasitic inductor, were analyzed theoretically and experimentally and accounted for using electro-magnetic (EM) simulation. The measurement results show that a dynamic gain control of 26 dB/16 dB in a control voltage range of 0.0–1.4 V has been achieved at 0.9/2.4 GHz respectively. Both S₁₁ and S₂₂ are below than –10 dB in all the control voltage range. Noise figures at both 0.9 GHz and 2.4 GHz are lower than 5 dB. Total power dissipation of the dual-band VGA is about 16.5 mW at 3 V supply.     

A 1.58 nW power consumption and 34.45 ppm/°C temperature coefficient bandgap reference (BGR) for subblocks of RFID tag

In this paper a bandgap reference (BGR) circuit irrespective of the temperature and the supply voltage variation with very low power consumption is proposed. The proportional to absolute temperature (PTAT) and complementary to absolute temperature (CTAT) generators of the proposed BGR, which has four cores cascaded with each other, are used in order to increase not only the output voltage, but also the output control ability for the temperature and the voltage insensitivity. To combine produced voltage from PTAT and CTAT generator, a weight combination circuit, which uses internal capacitors of transistors, is applied. Due to the fact that all of the transistors in such a topology are worked in sub-threshold region, the power consumption is significantly diminished to 1.58 nW. Also the variation of the temperature from −25 °C to 150 °C, leads to the temperature coefficient about 34.45 ppm/°C. The design simulation is done at 960 MHz frequency in TSMC 0.18 µm CMOS technology with the help of Cadence software. Also the post layout simulation result and the layout of the proposed circuit are presented. The output and the chip area of this BGR are 141.5 mV and 1387 µm² respectively.     

Design of an active CMOS subharmonic mixer with enhanced transconductance

This paper presents a wideband Gilbert subharmonic mixer (SHM) that partly overcomes the fundamental trade-off between radio frequency (RF) and intermediate frequency (IF) currents. Compared to the conventional SHM, the proposed SHM features large gain, low noise figure (NF) and moderate linearity over a wide bandwidth by concurrent usage of regulated-cascode RF-stage and inductive connection between RF and LO stages. Numerical analyses along with circuit-level simulations are given to evaluate the performance of the proposed mixer and facilitate its optimum design. Simulations using a 0.18 μm RF-CMOS process demonstrate that the proposed mixer, at a fixed IF of 100 MHz, exhibits more than 5 dB and 2 dB improvements in conversion gain (CG) and NF, respectively.     

0.8 V PLL-based automatic frequency tuning system for current-mode filters

A wide-range automatic frequency tuning system for current-mode filters is proposed in this paper. The cutoff frequency of the tunable filter is controlled by an external reference signal and is locked in the desired frequency through a current-mode based phase locked loop (PLL) circuit. Although the PLL operates in a relatively narrow band, the total tuning range of the topology is extended by interpolating an automatic frequency detector after the reference input and before the PLL. The use of current controlled oscillator, based on same blocks with those in the filter, offers accuracy and feasible design in the control path. The topology has been simulated using MOS transistor models for a 130 nm CMOS technology in 0.8 V supply voltage. The achieved overall automatic tuning range was from 2.3 MHz to 660 MHz.     

An LP/CBP reconfigurable analog baseband circuit for software-defined radio receivers in 65 nm CMOS

A low pass (LP) and complex band pass (CBP) reconfigurable analog baseband circuit for software-defined radio (SDR) receivers is presented. It achieves 1–15 MHz LP bandwidth, 2–8 MHz CBP bandwidth and 0–36 dB gain range with 1 dB step. Nulling-resistor Miller feed-forward (NRMFF) differential-mode compensation, passive left half-plane (LHP) zero common-mode compensation and Quasi-Floating Gate (QFG) technique are proposed to improve the high frequency performance and driving capability of the embedded fully differential operational amplifier (Op-Amp). The analog baseband circuit has been implemented in 65 nm CMOS. It achieves 15.2 dB m/27.1 dB m IB/OB-IIP3, −2 dB m IP1dB and 71 dB m IIP2 while consuming 3.6–9.1 mW from a 1.2 V power supply and 0.75 mm² chip area.     

Single-grain Si thin-film transistors SPICE model,analog and RF circuit applications

Single-grain thin-film transistors (SG-TFTs) fabricated inside location-controlled using μ-Czochralski process exhibit SOI-FETs like performance despite processing temperatures remaining below 350 °C. Thus, the SG-TFT is a potential technology for large-area highly-integrated electronic system and system-in-package, taking advantage of the system-on-flexible substrate and low manufacturing cost capabalities. The SG-TFT is modeled based on the BSIMSOI SPICE model where the mobility parameter is modified to fit the SG-TFT behavior. Therefore, analog and RF circuits can be designed and benchmarked. A two-stage telescopic cascode operational amplifier fabricated in a prototype 1.5 μm SG-TFT technology demonstrates DC gain of 55 dB and unity-gain bandwidth of 6.3 MHz. A prototype CMOS voltage reference demonstrates a power supply rejection ratio (PSRR) of 50 dB. With unity-gain frequency, f_T, in the GHz range, the SG-TFT can also enable RF circuits for wireless applications. A 12 dB gain RF cascode amplifier with integrated on-chip inductors operating in the 433 MHz ISM band is demonstrated.     

A novel wide band super transistor based voltage feedback current amplifier

This paper is assigned to the design of voltage feedback current amplifiers (VFCAs). Their operation and interesting characteristics are covered and a novel CMOS VFCA is presented. New ideas based on super transistors (STs) are devised and used to design a high performance VFCA. Benefiting from the interesting properties of STs, the proposed VFCA exhibits high linearity, high output impedance, very low input impedance and wide bandwidth. The proposed circuit is designed using TSMC 0.18 μm CMOS technology parameters and supply voltage of ±0.75 V. Simulation results with HSPICE show low THD of ?60 dB at the output signal, very low impedance of 0.6 Ω and 0.2 Ω at the input and feedback ports respectively and high output impedance of 10 MΩ. Moreover it can provide wide ?3 dB bandwidth of 15.5 MHz. The results prove the high capability of the VFCA in current mode signal processing and encourage strong motivation to develop commercially available VFCAs.     

A low-transconductance OTA with improved linearity suitable for low-frequency Gm-C filters

A fully differential operational transconductance amplifier is presented in this paper with enhanced linearity and low transconductance, suitable for low-frequency Gm-C filters. This paper also proposes a new common-mode feedback scheme that presents low sensitivity to large differential voltage swings at the OTA outputs. The proposed OTA was employed in the design of a fully-integrated Gm-C low-pass filter with a cutoff frequency of 30 kHz. The Gm-C filter was fabricated in a 0.35 μm CMOS technology and presented a THD at the output less than 1% for input signals with differential amplitudes up to 3.2 V.     

A low power current controllable single-input three-output current-mode filter using MOS transistors only

A novel circuit configuration for the realization of low power single-input three-output (SITO) current mode (CM) filters employing only MOS transistors are presented. The proposed circuit can realize low-pass (LP), band-pass (BP) and high-pass (HP) filter functions simultaneously at three high impedance outputs without changing configuration. Despite the other previously reported works, the proposed circuit is free from resistors and passive capacitors. Instead of passive capacitors; the gate-source capacitor of MOS transistor is used making the proposed circuit ideally suitable for integration. Compared to other works, the proposed filter has also the lowest number of transistors and lowest power consumption. The proposed circuit exhibits low-input and high-output impedances, which is highly desirable for cascading in CM signal processing. Moreover, it is center frequency can be electronically adjusted using a control current without a significant effect on quality factor (Q) granting it the highly desirable capability of electronic tunability. Transfer functions of the LP, BP and HP outputs are derived and the performance of the proposed circuit is proved through pre layout and post layout simulations at supply voltage of 1.8 V and using 0.18 μm CMOS process parameters. The power consumption and the required chip area are only 0.5 mW and 77.4 μm × 70.2 μm, respectively.     

Floating active inductor based Class-C VCO with 8 digitally tuned sub-bands

A fully integrated floating active inductor based voltage-controlled oscillator (VCO) is presented. The active inductor employs voltage differencing transconductance amplifier (VDTA) as a building block. The designed VCO achieves frequency tuning by varying the bias current through the VDTA and utilizes a Class-C topology for improving the phase noise performance. The inductor-less VCO is designed and implemented in a 45-nm CMOS process and its performance is estimated using Virtuoso ADE of Cadence. Operating at a supply voltage of ±1 V, the proposed VCO consumes 0.44–1.1 mW corresponding to the oscillation frequency of 1.1–1.8 GHz thereby exhibiting a tuning range of 48.27%. The phase noise of the VCO lies in the range of −94.12 to −98.37 dBc/Hz at 1 MHz offset resulting in a FOM of −172.14 to −176.69 dBc/Hz.     

A low-power rail-to-rail input-range linear delay element circuit

Delay elements are one of the key components in many time-domain circuits such as time-based analog-to-digital converters. In this paper, a new rail-to-rail current-starved delay element is proposed which not only presents good linearity for the voltage-delay curve over the input range of ground to supply voltage, but also it consumes a dynamic power only during the transition times without consuming any static power. The proposed delay element is designed and simulated in a 0.13-µm CMOS technology with a supply voltage of 1.2 V. Post-layout simulation results demonstrate that the proposed circuit has a linear voltage-delay transfer function with a voltage-to-time gain of −1.33 ps/mV. Moreover, when samples of a full-scale sin-wave input signal are applied to the proposed circuit with a clock frequency of 100 MHz, the power consumption is 30 µW, and signal-to-noise-and-distortion ratio (SNDR) of the output delay times is 30.4 dB, making it suitable for use in a time-based analog-to-digital converter with up to 5-bit resolution.     

An inductorless wideband common-gate LNA with dual capacitor cross-coupled feedback and negative impedance techniques

A wideband common-gate (CG) low-noise amplifier (LNA) with dual capacitor cross-coupled (CCC) feedback and negative impedance techniques is presented for multimode multiband wireless communication applications. Double CCC technique boosts the input transconductance of the LNA, and low power consumption is obtained by using current-reuse technique. Negative impedance technique is employed to alleviate the correlation between the transconductance of the matching transistors and input impedance. Meanwhile, it also allows us to achieve a lower noise figure (NF). Moreover, current bleeding technique is adopted to allow the choice of a larger load resistor without sacrificing the voltage headroom. The proposed architecture achieves low noise, low power and high gain simultaneously without the use of bulky inductors. Simulation results of a 0.18-μm CMOS implementation show that the proposed LNA provides a maximum voltage gain of 25.02 dB and a minimum NF of 2.37 dB from 0.1 to 2.25 GHz. The input-referred third-order intercept point (IIP3) and input 1-dB compression point (IP_1dB) are better than –7.8 dBm and –19.2 dBm, respectively, across the operating bandwidth. The circuit dissipates 3.24 mW from 1.8 V DC supply with an active area of 0.03 mm².     

A low phase noise and low power 3–5 GHz frequency synthesizer in 0.18 µm CMOS technology

A low power frequency synthesizer for WLAN applications is proposed in this paper. The NMOS transistor-feedback voltage controlled oscillator (VCO) is designed for the purpose of decreasing phase noise. TSPC frequency divider is designed for widening the frequency range with keeping low the power consumption. The phase frequency detector (PFD) with XOR delay cell is designed to have the low blind and dead zone, also for neutralizing the charge pump (CP) output currents; the high gain operational amplifier and miller capacitors are applied to the circuit. The frequency synthesizer is simulated in 0.18 µm CMOS technology while it works at 1.8 V supply voltage. The VCO has a phase noise of −136 dBc/Hz at 1 MHz offset. It has 10.2% tuning range. With existence of a frequency divider in the frequency synthesizer loop the output frequency of the VCO can be divided into the maximum ratio of 18. It is considered that the power consumption of the frequency synthesizer is 4 mW and the chip area is 10,400 µm².     

Transimpedance amplifier with a compression stage for wide dynamic range optical applications

A high dynamic input transimpedance amplifier was implemented in 130 nm CMOS technology. The proposed TIA is an inverter with a diode connected NMOS and a gate controlled PMOS loads which is cascode connected with the inverter. The square law compression NMOS increases the input photocurrent up to 10 mA. The TIA has an integrated input referred noise current of 135 nA, 227 MHz bandwidth. The TIA shows a transimpedance gain of 59 dBΩ and a 97 dB dynamic range. The TIA consumes 2.3 mA from 1.5 V voltage supply.