Stabilizing Polymer–Lithium Interface in a Rechargeable Solid Battery

Solid polymer electrolytes (SPEs) are promising candidates for developing high‐energy‐density Li metal batteries due to their flexible processability. However, the low mechanical strength as well as the inferior interfacial regulation of ions between SPEs and Li metal anode limit the suppress ion of Li dendrites and destabilize the Li anode. To meet these challenges, interfacial engineering aiming to homogenize the distribution of Li⁺/electron accompanied with enhanced mechanical strength by Mg₃N₂ layer decorating polyethylene oxide is demonstrated. The intermediary Mg₃N₂ in situ transforms to a mixed ion/electron conducting interlayer consisting of a fast ionic conductor Li₃N and a benign electronic conductor Mg metal, which can buffer the Li⁺ concentration gradient and level the nonuniform electric current distribution during cycling, as demonstrated by a COMSOL Multiphysics simulation. These characteristics endow the solid full cell with a dendrite‐free Li anode and enhanced cycling stability and kinetics. The innovative interface design will accelerate the commercial application of high‐energy‐density solid batteries.     

A Robust Dual-Polymer@Inorganic Networks Composite Polymer Electrolyte Toward Ultra-Long-Life and High-Voltage Li/Li-Rich Metal Battery

Composite polymer electrolytes (CSEs) that simultaneously possess superior electrochemical performances with robust mechanical properties are highly desired to the application of high-energy lithium metal batteries. Herein, a novel dual-polymer@inorganic network CSE (DNSE@IN) through a sequential nonhydrolytic sol-gel reaction of tetraethoxysilane (TEOS) and the semi-interpenetration of poly(vinylidene fluoride-co-hexafluoropropene)-hexafluoropropylene (P(VDF-HFP)) with poly(ionic liquid) (PIL) is proposed. DNSE@IN, which has a robust dual-polymer@inorganic networks, not only has high ionic conductivity (0.53 mS cm⁻¹ at 20 °C), but also exhibits an outstanding Young's modulus of 723.2 MPa. As a result, the DNSE@IN based Li/LiFePO₄ and Li/Li_1.17Ni_0.27Co_0.05Mn_0.52O₂ (Li-rich) cells exhibit remarkable cycling stability from room temperature (RT) to 100 °C. As-assembled Li/Li-rich battery shows superior cyclability of 194.3 mAh g⁻¹ after 70 cycles at 4.3 V under RT. Additionally, the scale-up high-voltage Li/Li-rich pouch cells exhibit excellent cyclability (nearly 100% capacity retention after 93 cycles) and superior flexibility, safety at RT for potential practical applications. As such, the work of decoupling ionic conductivity and mechanical properties opens a novel route to develop novel CSEs for the construction of high-energy lithium metal batteries.     

Molecular-level Designed Polymer Electrolyte for High-Voltage Lithium–Metal Solid-State Batteries

In solid polymer electrolytes (SPEs) based Li–metal batteries, the inhomogeneous migration of dual-ion in the cell results in large concentration polarization and reduces interfacial stability during cycling. A special molecular-level designed polymer electrolyte (MDPE) is proposed by embedding a special functional group (4-vinylbenzotrifluoride) in the polycarbonate base. In MDPE, the polymer matrix obtained by copolymerization of vinylidene carbonate and 4-vinylbenzotrifluoride is coupled with the anion of lithium-salt by hydrogen bonding and the “σ-hole” effect of the C F bond. This intermolecular interaction limits the migration of the anion and increases the ionic transfer number of MDPE (t_Li⁺ = 0.76). The mechanisms of the enhanced t_Li⁺ of MDPE are profoundly understood by conducting first-principles density functional theory calculation. Furthermore, MDPE has an electrochemical stability window (4.9 V) and excellent electrochemical stability with Li–metal due to the CO group and trifluoromethylbenzene (ph-CF₃) of the polymer matrix. Benefited from these merits, LiNi_0.8Co_0.1Mn_0.1O₂-based solid-state cells with the MDPE as both the electrolyte host and electrode binder exhibit good rate and cycling performance. This study demonstrates that polymer electrolytes designed at the molecular level can provide a broader platform for the high-performance design needs of lithium batteries.     

Ultra-Stretchable,Ionic Conducting,Pressure-Sensitive Adhesive with Dual Role for Stable Li-Metal Batteries

The practical application of lithium (Li) metal battery is impeded by the Li dendrite growth and unstable solid electrolyte interphase (SEI) layer. Herein, an ultra-stretchable and ionic conducting chemically crosslinked pressure-sensitive adhesive (cPSA) synthesized via the copolymerization of 2-ethylhexyl acrylate and acrylic acid with poly(ethyleneglycol)dimethacrylate as crosslinker (short for 70cPSA), is developed as both artificial SEI layer and solid polymer electrolyte (SPE) for stable Li-metal electrode, enabling all-solid-state Li metal batteries with excellent cycling performance. As an artificial SEI layer, the 70cPSA-modified electrodes exhibit excellent electrochemical performance in Li|70cPSA@Cu half cells and 70cPSA@Li|70cPSA@Li symmetric cells. In full cells with LiFePO₄ (LFP) as cathode, the 70cPSA@Li|LFP cell exhibits stable cycling performance over 250 cycles. Utilized as SPE, the all-solid-state Li|SPE|LFP cell delivers excellent cycling stability with a capacity retention of 86% over 500 cycles. With high-voltage LiNi_0.8Mn_0.1Co_0.1O₂ (NMC811) as cathode, the Li|SPE|NMC811 cell exhibits a discharge capacity of 124.3 mAh g⁻¹ with a capacity retention of 71% after 200 cycles. The rational design of PSAs and investigation of their dual role for stable and safe Li-metal batteries may shed a light on adhesive polymers for battery applications.     

Regulation of Interphase Layer by Flexible Quasi-Solid Block Polymer Electrolyte to Achieve Highly Stable Lithium Metal Batteries (Adv. Funct. Mater. 27/2023)

Low safety, unstable interfaces, and high reactivity of liquid electrolytes greatly hinder the development of lithium metal batteries (LMBs). Quasi-solid-state electrolytes (QGPEs) with superior mechanical properties and high compatibility can meet the demands of LMBs. Herein, a biodegradable polyacrylonitrile/polylactic acid-block-ethylene glycol polymer (PALE) as membrane skeleton for GPEs is designed and systematically investigated by regulating the length and structure of the cross-linked chain. Benefiting from the enriched affinitive sites of polar functional groups ( CO,  C O C,  CN, and  OH) in highly cross-linked polymer structure, the designed PALE membrane skeleton exhibits flame-retardant property and ultrahigh liquid electrolyte uptake property, and the derived quasi-solid-state PALE GPEs deliver enhanced stretchability and a higher electrochemical stable window of 5.11 V. Besides, the PALE GPEs effectively protect cathodes from corrosion while allowing uniform and fast transfer of Li⁺ ions. Therefore, the Li||Li symmetrical battery and LFP or NCM811||Li full-cell using PALE GPEs exhibit excellent cycling stability coupled with compact and flat inorganic/organic interface layers. And the excellent cycling stability of pouch cells under harsh operating conditions indicates the application possibilities of PALE GPEs in flexible devices with high-energy-density.     

In Situ Formation of Li3P Layer Enables Fast Li+ Conduction across Li/Solid Polymer Electrolyte Interface

Solid‐state polymer electrolytes provide better flexibility and electrode contact than their ceramic counterparts, making them a worthwhile pursuit for all‐solid‐state lithium‐metal batteries. However, their large Li/solid state electrolyte interfacial resistance, small critical current density, and rapid lithium dendrite growth during cycling still limit their viability. Owing to these restrictions, all‐solid‐state cells with solid polymer electrolytes must be cycled above room‐temperature and with a small current density. These problems can be mitigated with an in situ formed artificial solid electrolyte interphase that rapidly conducts Li⁺ ions. Herein, a Li₃P layer formed in situ at the Li‐metal/solid polymer electrolyte interphase is reported that significantly reduces the electrode/electrolyte interfacial resistance. Additionally, this layer increases the wettability of the solid polymer by the metallic lithium anode, allowing for the critical current density of lithium symmetric cells to be doubled by homogenizing the current density at the interface. All‐solid‐state Li/Li symmetric cells and Li/LiFePO₄ cells with the Li₃P layer show improved cycling performance with a high current density.     

Excellent Cycling Stability of Sodium Anode Enabled by a Stable Solid Electrolyte Interphase Formed in Ether‐Based Electrolytes

Sodium‐ion batteries have been considered one of the most promising power sources beyond Li‐ion batteries. Although the Na metal anode exhibits a high theoretical capacity of 1165 mAh g^?1, its application in Na batteries is largely hindered by dendrite growth and low coulombic efficiency. Herein, it is demonstrated that an electrolyte consisting of 1 m sodium tetrafluoroborate in tetraglyme can enable excellent cycling efficiency (99.9%) of a Na metal anode for more than 1000 cycles. This high reversibility of a Na anode can be attributed to a stable solid electrolyte interphase formed on the Na surface, as revealed by cryogenic transmission electron microscopy and X‐ray photoelectron spectroscopy (XPS). These electrolytes also enable excellent cycling stability of Na||hard‐carbon cells and Na||Na_2/3Co_1/3Mn_2/3O₂ cells at high rates with very high coulombic efficiencies.     

Highly‐Cyclable Room‐Temperature Phosphorene Polymer Electrolyte Composites for Li Metal Batteries

Despite significant interest toward solid‐state electrolytes owing to their superior safety in comparison to liquid‐based electrolytes, sluggish ion diffusion and high interfacial resistance limit their application in durable and high‐power density batteries. Here, a novel quasi‐solid Li⁺ ion conductive nanocomposite polymer electrolyte containing black phosphorous (BP) nanosheets is reported. The developed electrolyte is successfully cycled against Li metal (over 550 h cycling) at 1 mA cm^?2 at room temperature. The cycling overpotential is dropped by 75% in comparison to BP‐free polymer composite electrolyte indicating lower interfacial resistance at the electrode/electrolyte interfaces. Molecular dynamics simulations reveal that the coordination number of Li⁺ ions around (trifluoromethanesulfonyl)imide (TFSI^?) pairs and ethylene‐oxide chains decreases at the Li metal/electrolyte interface, which facilitates the Li⁺ transport through the polymer host. Density functional theory calculations confirm that the adsorption of the LiTFSI molecules at the BP surface leads to the weakening of N and Li atomic bonding and enhances the dissociation of Li⁺ ions. This work offers a new potential mechanism to tune the bulk and interfacial ionic conductivity of solid‐state electrolytes that may lead to a new generation of lithium polymer batteries with high ionic conduction kinetics and stable long‐life cycling.     

Template-Sacrificed Hot Fusion Construction and Nanoseed Modification of 3D Porous Copper Nanoscaffold Host for Stable-Cycling Lithium Metal Anodes

Lithium (Li) metal anodes have been proposed as a promising candidate for high-energy-density electrode materials in secondary batteries. However, the dendrite growth and unstable electrode–electrolyte interfaces during Li plating/stripping are fatal to their practical applications. Herein, the construction of 3D porous Au/Cu nanoscaffold prepared via a convenient template-sacrificed hot fusion construction method and a nanoseed modification process as an effective Li metal hosting material are proposed. The Au/Cu nanoscaffold can spatially guide uniform deposition of Li metal free from the growth of Li dendrites due to the homogenous Li⁺ ion flux and negligible nucleation overpotential. Moreover, the Cu skeleton can relieve volume change and stabilize local current density during cycling processes. Benefiting from these advantages, the symmetric cells based on self-supported Li-filled Au/Cu (Li-Au/Cu) nanoscaffold electrodes present highly stable Li plating/stripping for more than 1000 h with a low voltage hysteresis less than 90 mV and a long lifespan over 1300 h at 1.0 mA cm^–2 in carbonate-based electrolytes. Impressively, the Li-Au/Cu nanoscaffold||LiFePO₄ full cells also exhibit exceptional cycling stability and rate performance. This work provides a promising strategy to construct dendrite-free lithium metal anodes toward high-performance lithium metal batteries.     

A Safe Polyzwitterionic Hydrogel Electrolyte for Long‐Life Quasi‐Solid State Zinc Metal Batteries

Aqueous zinc metal batteries are safe, economic, and environmentally friendly. However, the dendrite growth and inevitable corrosion issues under aqueous condition greatly restrict the development of long cycling life zinc metal batteries. To achieve the long‐term reversible zinc deposition/dissolution, a polyzwitterionic hydrogel electrolyte (PZHE) is constructed with record high room temperature ionic conductivity of 32.0 mS cm^?1 and Zn²⁺ transference number of 0.656. The abundant hydrophilic and charged groups in the zwitterionic polymer can well immobilize water molecules in the polymer skeleton and reduce side reactions. The charged groups of the zwitterionic polymer can also homogenize the ion distribution and achieve uniform zinc deposition. Long cycling life of over 3500 h is achieved for the symmetric batteries with PZHE. Full cells with VS₂ and MnO₂ cathodes are also demonstrated to exhibit excellent cycling stability. With combined advantages of physical and chemical crosslinking gels, the PZHE enabled flexible quasi‐solid state zinc metal batteries with excellent processability, self‐healing property and safety, can operate even under various extreme conditions such as cutting, soaking, hammering, washing, burning, and freezing. It is believed that the PZHE can provide a promising opportunity and pave the way for other long‐life aqueous batteries.     

A Stable Polymer-based Solid-State Lithium Metal Battery and its Interfacial Characteristics Revealed by Cryogenic Transmission Electron Microscopy

Solid-state lithium metal batteries (SSLMBs) are a promising candidate for next-generation energy storage systems due to their intrinsic safety and high energy density. However, they still suffer from poor interfacial stability, which can incur high interfacial resistance and insufficient cycle lifespan. Herein, a novel poly(vinylidene fluoride‑hexafuoropropylene)-based polymer electrolyte (PPE) with LiBF₄ and propylene carbonate plasticizer is developed, which has a high room-temperature ionic conductivity up to 1.15 × 10⁻³ S cm⁻¹ and excellent interfacial stability. Benefitting from the stable interphase, the PPE-based symmetric cell can operate for over 1000 h. By virtue of cryogenic transmission electron microscopy (Cryo-TEM) characterization, the high interfacial compatibility between Li metal anode and PPE is revealed. The solid electrolyte interphase is made up of an amorphous outer layer that can keep intimate contact with PPE and an inner Li₂O-dominated layer that can protect Li from continuous side reactions during battery cycling. A LiF-rich transition layer is also discovered in the region of PPE close to Li metal anode. The feasibility of investigating interphases in polymer-based solid-state batteries via Cryo-TEM techniques is demonstrated, which can be widely employed in future to rationalize the correlation between solid-state electrolytes and battery performance from ultrafine interfacial structures.     

Largely Promoted Mechano-Electrochemical Coupling Properties of Solid Polymer Electrolytes by Introducing Hydrogen Bonds-Rich Network

Solid polymer electrolytes (SPEs) and their composites are the most promising spices to access the commercial application in all-solid-state lithium batteries, where definite requirements for SPEs should be satisfied including moderate mechanical strength, high Li-ion conductivity, and stable electrode/electrolyte interface. Herein, polyurethane-based polymer (PNPU) is designed to further construct the hybrid solid polymer electrolyte (named as PNPU-PVDF-HFP) with poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) for high energy density solid-state lithium metal batteries. The theoretical calculation and characterization demonstrate that PNPU-PVDF-HFP SPEs still maintain the multiple hydrogen bonding modes of PNPU, which contributes a significantly improved mechanical properties of the polymer membrane with compact structure. Moreover, it is corroborated that PNPU is involved to form the double Li⁺ transport paths in the hybrid electrolyte, accelerating the migration of lithium ions. Therefore, PNPU-PVDF-HFP SPEs are achieved with suitable tensile strength of 5.16 MPa and high elongation of 140.8%, high ambient ionic conductivity of 4.13 × 10⁻⁴ S cm⁻¹, excellent ductile, and stability on the interface of lithium metal anode. The Li/ LiFePO₄ and Li/Li[Ni_0.8Co_0.1Mn_0.1]O₂ solid-state batteries using PNPU-PVDF-HFP SPEs present a stable cycling performance at 30 °C. This study provides a feasible strategy to achieve mechano-electrochemical coupling stable SPEs for solid-state batteries.     

Building Artificial Solid‐Electrolyte Interphase with Uniform Intermolecular Ionic Bonds toward Dendrite‐Free Lithium Metal Anodes

Li metal has been widely regarded as a promising anode for next‐generation batteries due to its high theoretical capacity and low electrochemical potential. The unstable solid‐electrolyte interphase (SEI) and uncontrollable dendrite growth, however, incur severe safety hazards and hamper the practical application of Li metal anodes. Herein, an advanced artificial SEI layer constructed by [LiNBH]_n chains, which are crosslinked and self‐reinforced by their intermolecular Li? N ionic bonds, is designed to comprehensively stabilize Li metal anodes on a molecular level. Benefiting from its polymer‐like structure, the [LiNBH]_n layer is flexible and effectively tolerates the volume change of Li metal anodes. In addition, this layer with high polarity in its structure, helps to regulate the homogeneous distribution of the Li⁺ flux on Li electrodes via the further formation of Li? N bonds. The designed [LiNBH]_n layer is electrically nonconductive but highly ionically conductive, thus facilitating Li⁺ diffusion and confining Li deposition beneath the layer. Therefore, under the protection of the [LiNBH]_n layer, the Li metal anodes exhibit stable cycling at a 3 mA cm^?2 for more than 700 h, and the full cells with high lithium iron phosphate and sulfur cathodes mass loading also present excellent cycling stability.     

Ultrathin Layered Double Hydroxide Nanosheets Enabling Composite Polymer Electrolyte for All-Solid-State Lithium Batteries at Room Temperature

Solid electrolytes are the most promising substitutes for liquid electrolytes to construct high-safety and high-energy-density energy storage devices. Nevertheless, the poor lithium ion mobility and ionic conductivity at room temperature (RT) have seriously hindered their practical usage. Herein, single-layer layered-double-hydroxide nanosheets (SLN) reinforced poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) composite polymer electrolyte is designed, which delivers an exceptionally high ionic conductivity of 2.2 × 10⁻⁴ S cm⁻¹ (25  ° C), superior Li⁺ transfer number ( ≈ 0.78) and wide electrochemical window ( ≈ 4.9 V) with a low SLN loading ( ≈ 1 wt%). The Li symmetric cells demonstrate ultra-long lifespan stable cycling over ≈ 900 h at 0.1 mA cm⁻², RT. Moreover, the all-solid-state Li|LiFePO₄ cells can run stably with a high capacity retention of 98.6% over 190 cycles at 0.1 C, RT. Moreover, using LiCoO₂/LiNi_0.8Co_0.1Mn_0.1O₂, the all-solid-state lithium metal batteries also demonstrate excellent cycling at RT. Density functional theory calculations are performed to elucidate the working mechanism of SLN in the polymer matrix. This is the first report of all-solid-state lithium batteries working at RT with PVDF-HFP based solid electrolyte, providing a novel strategy and significant step toward cost-effective and scalable solid electrolytes for practical usage at RT.     

Constructing a High‐Strength Solid Electrolyte Layer by In Vivo Alloying with Aluminum for an Ultrahigh‐Rate Lithium Metal Anode

The serious safety issues caused by uncontrollable lithium (Li) dendrite growth, especially at high current densities, seriously hamper the rapid charging of Li metal‐based batteries. Here, the construction of Al–Li alloy/LiCl‐based Li anode (ALA/Li anode) is reported by displacement and alloying reaction between an AlCl₃‐ionic liquid and a Li foil. This layer not only has high ion‐conductivity and good electron resistivity but also much improved mechanical strength (776 MPa) as well as good flexibility compared to a common solid electrolyte interphase layer (585 MPa). The high mechanical strength of the Al–Li alloy interlayer effectively eliminates volume expansion and dendrite growth in Li metal batteries, so that the ALA/Li anode achieves superior cycling for 1600 h (2.0 mA cm^?2) and 1000 cycles at an ultrahigh current density (20 mA cm^?2) without dendrite formation in symmetric batteries. In lithium–sulfur batteries, the dense alloy layer prevents direct contact between polysulfides and Li metal, inhibiting the shuttle effect and electrolyte decomposition. Long cycling performance is achieved even at a high current density (4 C) and a low electrolyte/sulfur (6.0 µL mg^?1). This easy fabrication process provides a strategy to realize reliable safety during the rapid charging of Li‐metal batteries.     

3D Porous Cu Current Collector/Li‐Metal Composite Anode for Stable Lithium‐Metal Batteries

Lithium‐metal batteries are of particular interest for next‐generation electrical energy storage because of their high energy density on both volumetric and gravimetric bases. Effective strategies to stabilize the Li‐metal anode are the prerequisite for the progress of these exceptional storage technologies, such as Li–S and Li–O₂ batteries. Various challenges, such as uneven Li electrodeposition, anode volume expansion, and dendrite‐induced short‐circuit have hindered the practical application of rechargeable Li‐metal batteries. Herein, a one‐step facile and cost‐effective strategy for stabilizing lithium‐metal batteries via 3D porous Cu current collector/Li‐metal composite anode is reported. The porous structure of the composite electrode provides a “cage” for the redeposition of “hostless” lithium and accommodates the anode volume expansion during cycling. Compared with planar Cu foil, its high specific surface area favors the electrochemical reaction kinetics and lowers the local current density along the anode. It leads to low interfacial resistance and stabilizes the Li electrodeposition. On this basis, galvanostatic measurements are performed on both symmetric cells and Li/Li₄Ti₅O₁₂ cells and it is found that the electrodes exhibit exceptional abilities of promoting cell lifetime and stabilizing the cycling behavior. Although this work focuses on lithium metal, this novel tactic is easy to generalize to other metal electrodes.     

Low Resistance–Integrated All‐Solid‐State Battery Achieved by Li7La3Zr2O12 Nanowire Upgrading Polyethylene Oxide (PEO) Composite Electrolyte and PEO Cathode Binder

All‐solid‐state lithium metal battery is the most promising next‐generation energy storage device. However, the low ionic conductivity of solid electrolytes and high interfacial impedance with electrode are the main factors to limit the development of all‐solid‐state batteries. In this work, a low resistance–integrated all‐solid‐state battery is designed with excellent electrochemical performance that applies the polyethylene oxide (PEO) with lithium bis(trifluoromethylsulphonyl)imide as both binder of cathode and matrix of composite electrolyte embedded with Li₇La₃Zr₂O₁₂ (LLZO) nanowires (PLLN). The PEO in cathode and PLLN are fused at high temperature to form an integrated all‐solid‐state battery structure, which effectively strengthens the interface compatibility and stability between cathode and PLLN to guarantee high efficient ion transportation during long cycling. The LLZO nanowires uniformly distributed in PLLN can increase the ionic conductivity and mechanical strength of composite electrolyte efficiently, which induces the uniform deposition of lithium metal, thereby suppressing the lithium dendrite growth. The Li symmetric cells using PLLN can stably cycle for 1000 h without short circuit at 60 °C. The integrated LiFePO₄/PLLN/Li batteries show excellent cycling stability at both 60 and 45 °C. The study proposed a novel and robust battery structure with outstanding electrochemical properties.     

Safe,Stable Cycling of Lithium Metal Batteries with Low‐Viscosity,Fire‐Retardant Locally Concentrated Ionic Liquid Electrolytes

Ionic liquid (IL) electrolytes with concentrated Li salt can ensure safe, high‐performance Li metal batteries (LMBs) but suffer from high viscosity and poor ionic transport. A locally concentrated IL (LCIL) electrolyte with a non‐solvating, fire‐retardant hydrofluoroether (HFE) is presented. This rationally designed electrolyte employs lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), 1‐methyl‐1‐propyl pyrrolidinium bis(fluorosulfonyl)imide (P13FSI) and 1,1,2,2‐tetrafluoroethyl 2,2,3,3‐tetrafluoropropyl ether (TTE) as the IL and HFE, respectively (1:2:2 by mol). Adding TTE enables a Li‐concentrated IL electrolyte with low viscosity and good separator wettability, facilitating Li‐ion transport to the Li metal anode. The non‐flammability of TTE contributes to excellent thermal stability. Furthermore, synergy between the dual (FSI/TFSI) anions in the LCIL electrolyte can help modify the solid electrolyte interphase, increasing Li Coulombic efficiency and decreasing dendritic Li deposition. LMBs (Li||LiCoO₂) employing the LCIL electrolyte exhibit good rate capability (≈89 mAh g^?1 at 1.8 mA cm^?2, room temperature) and long‐term cycling (≈80% retention after 400 cycles).     

Shaping the Contact between Li Metal Anode and Solid‐State Electrolytes

Scientific and technological interest in solid‐state Li metal batteries (SSLMBs) arises from their excellent safety and promising high energy density. However, the practical application of SSLMBs is hindered by poor contact between the Li metal anode (LMA) and solid‐state electrolytes (SSEs). To circumvent this limitation, a pattern‐guided approach that shapes the LMA/SSE contact is disclosed to offer fast Li ion conduction in the interface. A thermally‐treated copper foam is used as the lithophilic pattern to confine and guide Li for forming a tight contact with garnet‐type SSE. The contact can be easily manipulated according to the shape of lithiophilic pattern, facilitating cell assembly. The resulting Li|patterned garnet|Li symmetric cell exhibits an interfacial resistance of 9.8 Ω cm², which is dramatically lower than that of 998 Ω cm² for Li|pristine garnet|Li symmetric cell. Being used in Li–sulfur batteries, the patterned garnet effectively eliminates the polysulfide shuttle and enables stable cycling performance, showing a low capacity decay of 0.035% per cycle over 1000 cycles. The fundamental contact process of metallic anodes/SSEs is carefully investigated. This contact strategy provides a new design concept to improve the interface wettability via a lithiophilic pattern for a variety of SSEs that cannot wet with metallic anodes.     

Enhanced Interfacial Stability of Hybrid‐Electrolyte Lithium‐Sulfur Batteries with a Layer of Multifunctional Polymer with Intrinsic Nanoporosity

The use of lithium‐ion conductive solid electrolytes offers a promising approach to address the polysulfide shuttle and the lithium‐dendrite problems in lithium‐sulfur (Li‐S) batteries. One critical issue with the development of solid‐electrolyte Li‐S batteries is the electrode–electrolyte interfaces. Herein, a strategic approach is presented by employing a thin layer of a polymer with intrinsic nanoporosity (PIN) on a Li⁺‐ion conductive solid electrolyte, which significantly enhances the ionic interfaces between the electrodes and the solid electrolyte. Among the various types of Li⁺‐ion solid electrolytes, NASICON‐type Li_1+xAl_xTi_2‐x(PO₄)₃ (LATP) offers advantages in terms of Li⁺‐ion conductivity, stability in ambient environment, and practical viability. However, LATP is susceptible to reaction with both the Li‐metal anode and polysulfides in Li‐S batteries due to the presence of easily reducible Ti⁴⁺ ions in it. The coating with a thin layer of PIN presented in this study overcomes the above issues. At the negative‐electrode side, the PIN layer prevents the direct contact of Li‐metal with the LATP solid electrolyte, circumventing the reduction of LATP by Li metal. At the positive electrode side, the PIN layer prevents the migration of polysulfides to the surface of LATP, preventing the reduction of LATP by polysulfides.