Molybdenum nitride for the direct decomposition of NO

The physico-chemical properties of passivated -Mo₂N have been investigated. The material showed high activities for NO direct decomposition: nearly 100% NO conversion and 95% N₂ selectivity were achieved at 450C. The amount of O₂ taken up by -Mo₂N increased with temperature rise and reached 3133.9 molg^–1 at 450C; we conclude that there formation of Mo₂O_xN_y occurred. This oxygen-saturated -Mo₂N material was catalytically active: NO conversion and N₂ selectivity were 89 and 92% at 450C. We found that by means of H₂ reduction at 450C, Mo₂O_xN_y could be reduced back to -Mo₂N and the oxidation/reduction cycle is repeatable; such a behaviour and the high oxygen capacity (3133.9 molg^–1) of -Mo₂N suggest that -Mo₂N is a promising catalytic material for automobile exhaust purification.     

Lamellar Thickness of a Syndiotactic Polystyrene Determined from Small-angle X-ray Scattering and Transmission Electron Microscopy

Extensive morphological studies on a syndiotactic polystyrene (sPS) sample prepared from compression molding were carried out using small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). SAXS was conducted at 25C as well as at 150C to enhance the scattering contrast in order to obtain more reliable morphological parameters. The compression-molded sample was crystallized into a orthorhombic crystal lattice characterized by wide-angle X-ray diffraction (WAXD). A similar weight fraction of crystallinity, ca. 0.37, was obtained from both WAXD and differential scanning calorimetry measurements.In addition to the scattering peak at a scattering vector of ca. 0.36 nm^–1 attributable to the presence of lamellar/amorphous layers, anomalous scattering at the zero angle was found from the SAXS intensity profiles. Based on the Debye–Bueche theory, the scattering profile of this peculiar zero-angle scattering was deduced and was subtracted from the raw intensity profile to obtain the intensity profile exclusively associated with the lamellar/amorphous structure. A consistent long period was obtained for SAXS measured either at 25 or 150C, provided that the appropriate subtraction of intensities due to the zero-angle scattering was conducted. Moreover, the lamellar thickness deduced from the one-dimensional correlation function was in good agreement with TEM results. A difference scattering pattern derived from SAXS measured at 150 and 25C was obtained and a comparison of the morphological parameters was provided as well.     

Cooperative inclusion of sodium 1-pyrenesulfonate by γ-cyclodextrin

Summary The interaction of -cyclodextrin(-CD) with sodium 1-pyrenesulfonate(PS) was studied spectrophotometrically. -CD was found to cause much larger decrease in the absorption maxima of PS than -CD. The fluorescence spectra of PS in the presence of -CD showed excimer emission, while those of PS with -CD showed only monomer emission, indicating that -CD forms 12 (-CDPS) complexes in which two PS molecules are included in the -CD cavity in a face-to-face fashion. The binding isotherm showed a sigmoidal curve. The association constants were estimated by computer simulation of the binding curve. The 12 (CDPS) complex was found to be much more stable (K=10⁶ M^–1) than the 11 complex (K=1 M^–1). At high concentration of -CD another -CD cooperates in binding two PS molecules, resulting in the formation of a 22 complex.     

Synthesis of new metal-containing side-chain monomers and polymers

New metal-containing vinyl monomers, hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl]benzoyloxy}methacrylate, and the corresponding homopolymers and random copolymers with hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate were synthesized. The compounds were characterized by¹H NMR; their thermal behavior was investigated by means of differential scanning calorimetry. Monomers and polymers containing the ferrocene unit melt at lower temperatures than those derived from the cyclopentadienyl managanese tricarbonyl moiety. The melting temperatures of the monomers and polymers ranged from 399 to about 515 K, Both monomers and polymers failed to exhibit mesogenic behavior. Values ofM _n,M _w,M _w/M _n, and degree of polymerization were obtained by gel permeation chromatography. TheM _n ranged from 16,500 for the copolymer containing hexyl-6-oxy-{4-[4-(4-ferrocenoyl phenyl)phenyl] benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 26,000 for the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio.M _w/M _n ranged from 1.6 in the case of the copolymer containing hexyl-6-oxy-{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate and hydroxy monomer hexyl-6-oxy-{4-[4-(4-hydroxyphenyl)phenyl]benzoyloxy}methacrylate at a 1:3 ratio to 2.2 in the case of poly(hexyl-6-oxy{4-[4-(4-carboxy cyclopentadienyl manganese tricarbonyl phenyl)phenyl]benzoyloxy}methacrylate).     

In situ EXAFS study of the bimetallic interaction in a rhenium-promoted alumina-supported cobalt Fischer–Tropsch catalyst

The local environments about the rhenium atoms in a Co–Re/-Al₂O₃ catalyst after different reduction periods have been studied by X-ray absorption spectroscopy (EXAFS). The bimetallic catalyst containing 4.6 wt% cobalt and 2 wt% rhenium has been compared with a corresponding monometallic sample with 2 wt% rhenium on the same support. The rhenium L_III EXAFS analysis shows that bimetallic particles are formed after reduction at 450C with the average particle size being less than 15 Å. More than 6 h reduction at 450C is required for complete reduction of accessible rhenium.     

New polyisobutylene based model ionomers

Three-arm star polyisobutylene ionomers (¯M_n=8800) with terminal SO₃ M (M=K or Ca²) groups were synthesized and their mechanical properties investigated. Compression molded films displayed high elongations, i.e., -1000% for Ca² ionomers with lower values for the K counterions. Strain induced crystallinity was observed at higher elongations. Mechanical properties in general compared favorably with conventional covalently linked rubbery networks and were comparable and in some cases superior to EPDM-based ionomers carrying randomly distributed SO₃ M groups.For the first two parts see Proceedings, 28th IUPAC Macromolecular Symposium, Amherst, MA, July 11–16, 1982, p. 905 and 906     

Dynamic mechanical properties of crosslinked polyisoprene under deformation

Summary Molecular motions of elastomers under deformations were observed through dynamic mechanical measurements. Composite master curves of dynamic moduli E and E and loss tangent tan over a wide range of frequency and in a state of elongation were obtained by the time-temperature superposition procedure. It is found that both moduli increase with strain, . The slope of the dispersion curve of E become more gradual with the increase in , while that of E is almost unchanged. The increment of E is generally larger than that of E, which does not agree with the N. W. Tschoegl prediction, E ^* ()=f() E _o ^* (), where E ^* () and E _o ^* () are complex moduli at the strain of and O, respectively, and f() is the function of only . The difference in the strain dependence of E from E was found to correspond to the strain dependence of the equilibrium modulus.     

Properties ofSrMO 3-δ(M=Fe,Co) as oxygen electrodes in alkaline solution

Strontium ferrates and cobaltates with compositions SrFeO_3- (0.060.40) and SrCoO_3- (0.040.30) were synthesized. The dependence of the oxygen electrode properties on the value was examined in 1 mol dm^–3 KOH solution. In the SrFeO_3- series, the samples with 0.24<<0.29, showed the highest activity in both oxygen evolution and reduction reactions. In contrast, no strong dependence on the value was observed in SrCoO_3-, which also showed a high catalytic activity for oxygen evolution.     

Synthesis of ternary Li–Mn–O phase at a temperature of 260 ∘C and electrochemical lithium insertion into the oxide

A lithium–manganese oxide, Li _x MnO₂ (x=0.30.6), has been synthesized by heating a mixture (Li/Mn ratio=0.30.8) of electrolytic manganese dioxide (EMD) and LiNO₃ in air at moderate temperature, 260 C. The formation of the Li–Mn–O phase was confirmed by X-ray diffraction, atomic absorption and electrochemical measurements. Electrochemical properties of the Li–Mn–O were examined in LiClO₄-propylene carbonate electrolyte solution. About 0.3 Li in Li _x MnO₂ (x=0.30.6) was removed on initial charging, resulting in characteristic two discharge plateaus around 3.5V and 2.8V vs Li/Li⁺. The Li _x MnO₂ synthesized by heating at Li/Mn ratio=0.5 demonstrated higher discharge capacity, about 250mAh (g of oxide)^–1 initially, and better cyclability as a positive electrode for lithium secondary battery use as compared to EMD.     

Lamellar Morphology of Poly(3-hydroxybutyrate)/Poly(ethylene oxide) Blends as Studied via Small Angle X-ray Scattering

The lamellar morphology of a melt-miscible blend consisting of two crystalline constituents, poly(3-hydroxybutyrate) (PHB) and poly(ethylene oxide) (PEO) have been investigated by means of small angle X-ray scattering (SAXS). The blend was a crystalline/amorphous system when temperatures lay between the melting point of PEO (ca. T _m ^PEO=60C) and that of PHB (ca. T _m ^PHB=170C), while it became a crystalline/crystalline system below T _m ^PEO. The crystalline microstructures of the blends were induced by two types of crystallization history, i.e. one-step and two-step crystallizations. In the one-step crystallization, the blends were directly quenched from the melt to room temperature to allow simultaneous PHB and PEO crystallization. The two-step crystallization involved first cooling to 70C to allow PHB crystallization for 72 h followed by cooling to room temperature (ca. 19C) to allow PEO crystallization. In the crystalline/crystalline state, two scattering peaks have been observed in the Lorentz-corrected SAXS profiles, irrespective of the crystallization histories, meaning that crystallization created separate PHB and PEO lamellar stack domains. One-step crystallization yielded lamellar stack domains containing almost pure PHB and PEO lamellae. Two-step crystallization generated almost pure PHB lamellar domains and the PEO lamellar domains with inserted PHB lamellae. In the crystalline/amorphous state, the composition dependence of the amorphous layer thickness (l _a), the presence of zero-angle scattering, and the volume fraction of the PHB lamellar stack (_s) revealed that both one-step and two-step crystallizations, generated the interfibrillar segregation morphology, where the extent of interfibrillar segregation of amorphous PEO increased with increasing PEO content.     

On the preparation and properties of CuZSM-5 catalysts for NO decomposition

Equilibrium exchange isotherms were determined for the exchange of Cu²⁺ with NaZSM-5 at varying Cu(Ac)₂ concentrations in solutions of constant volume and zeolite weight. At low Cu²⁺ levels the solid scavenged all the copper ions. When copper could be detected in the equilibrated solutions, overexchange was observed. The extent of overexchange was higher at pH 6 than at pH 4. These results were analyzed in relation to catalytic activity.On leave from the Central Institute for Chemistry, Hungarian Academy of Sciences, H1525 Budapest, Hungary.     

Catalytic oxidation of methanol to methyl formate over silver – a new purpose of a traditional catalysis system

Catalytic reaction was performed in the unregarded temperature region over silver catalysts with long catalytic lifetime for the conversion of methanol to methyl formate. O-saturated or O-saturated silver catalysts were studied individually to identify the roles of O, O in the oxidative esterification of methanol over an unsupported polycrystalline silver catalyst. A synergic process is proposed based on the coexistence of -oxygen species and -oxygen species on the surface of polycrystalline silver at about 573 K.     

Effect of framework aluminum in proton‐ or copper‐exchanged MFI ferrialuminosilicates on their activity for the reduction of nitric oxide with ammonia

Reduction of NO with ammonia in excess oxygen has been carried out on protonform and Cu²⁺exchanged MFI ferrialuminosilicate. Though HZSM5 showed very low activity, the framework Al in Hferrialuminosilicate greatly enhanced the activity. The framework Al in Cu²⁺exchanged ferrialuminosilicate also enhanced the activity to some extent.     

Ethynylene-disilanylene copolymers

Polymers of structure (SiR₂SiR₂-C C-SiR₂SiR₂-C C) _n , in which ethynylene units alternate with disilylene units, have been prepared by two routes: (a) condensation of dichlorodisilanes with dilithium derivatives of 1,2-diethynyldisilanes and (b) ring-opening polymerization of strained cyclic disilanylene-acetylnes, (SiR₂SiR₂C C)₂. The polymers display UV absorption near 240 nm indicative of – conjugation between the Si₂ and the C C moieties. Polymers with R=R=n-Bu or R=n-Bu, R=Ph, undergo solid-state transitions to form liquid crystalline mesophases resembling those observed for many poly(silylenes). Single crystals were obtained for the polymer with R=R=CH₃, by precipitation from dilute cyclohexane solution. The solid-state properties and structures of this family of polymers are discussed.This paper was presented at the Second International Topical Workshop, Advances in Silicon-Based Polymer Science.     

Gas-phase synthesis of MTBE from methanol and t-butanol over the microporous niobium silicate AM-11

The methyl t-butyl ether (MTBE) synthesis is demonstrated, where MTBE is produced by reacting methanol and t-butanol over the microporous niobium silicate AM-11 (Aveiro Manchester, structure number 11). The effect of the methanol/t-butanol molar ratio, weight hourly space velocity (WHSV) and time on stream (TOS) on this reaction is investigated. These experiments are carried out in the gas phase at temperatures in the range 50–100C and at atmospheric pressure, yielding considerable selectivity for MTBE at low reaction temperatures. The selectivity to MTBE decreases with increasing temperature due to by-products formation. There is no catalyst deactivation during a period of more than 23 h on stream at 70C. Using the catalyst three times has no effect on the catalyst activity and selectivity for MTBE.     

Kinetics and Mechanism of Copolymerization of α-terpineol with Methylmethacrylate in Presence of Azobisisobutyronitrile as an Initiator

The radical copolymerization of -terpineol with methyl-methacrylate in xylene at 80±0.1C for 50 minutes in the presence of azobisisobutyronitrile (AIBN) follows ideal kinetics and results in the formation of a functional and random copolymer. The activation energy is 33 KJ/mole. The IR spectrum and NMR spectra of the copolymer(s) shows the bands at 1750 and 3400 cm^–1 for ester group of methylmethacrylate and alcoholic group of -terpineol and peaks at 3 to 4 for methoxy group and at 6.5 to 7.5 due to alcoholic group of methylmethacrylate and -terpineol repectively. The values of reactivity ratios, calculated by Kelen–Tüdos method, are r ₁ (MMA) = 0.18 and r ₂ (-terpineol) = 0.046. The Alfrey-Price; Q–e parameters for -terpineol has been calculated as 0.149 and 2.486. The mechanism of copolymerization has been elucidated and it is concluded that the double bond present in the monocyclic ring of -terpineol is an active site for copolymerization and the alcoholic group of -terpineol remain to give functional copolymer.     

Monotropic liquid crystalline poly(β-thioester)s containing bis (p-oxybenzoate) mesogenic units

Summary A new series of thermotropic liquid crystalline poly(-thioester)s was prepared by a Michael-type polyaddition of ,-polymethylenedithiols of different length to a mesogenic diacrylate containing two bis(p-oxybenzoate) units symmetrically connected through a dodecamethylene segment. The thermotropic behaviour was studied by combined DSC and thermal-optical analyses. All the poly(-thioester)s investigated exhibited quite unusual monotropic mesomorphism.     

Variable‐temperature IR spectroscopic studies of CO adsorbed on Na‐ZSM‐5 and Na‐Y zeolites

CO interacts with extraframework alkali metal cations (M⁺=) of zeolites to form both M⁺CO and M⁺OC species. By using variabletemperature FTIR spectroscopy, these Cbonded and Obonded species were found to be in a temperaturedependent equilibrium. For the same cation, the difference in interaction energy depends upon the zeolite framework. Thus, for the equilibrium process ZNa⁺=CO ZNa⁺OC, where Z represents the zeolite framework, H ⁰ was found to take the values 3.8 and 2.4 kJ mol^– for CO/NaZSM5 and CO/NaY, respectively. The Cbonded species show always the highest cation–CO interaction energy.     

Evaluation of the Form Birefringence and Other Structural Parameters Due to Thermal Annealing for Nylon 6 Fibers

In the present work nylon 6 fibers were annealed at 155±1C at different times and allowed to cool down in the oven to room temperature (27±1C). A Pluta polarizing interference microscope was used for measuring the changes in the optical parameters. From the optical and density parameters the optical orientation values of F ₂(), F ₄(), F ₆() and F _av were calculated. Also, the dielectric constant, dielectric susceptibility, molar refractivity, segment anisotropy, optical stress coefficient, optical configuration and the form birefringence were evaluated. The segment anisotropy and deformational thermal stress was evaluated. Relationships between the measured and calculated parameters are given for illustration. The mechanism of structural variations for nylon 6 fiber due to the annealing process is discussed, and structural details for opto thermal parameters are explained. The present study throws light on the changes due to thermal annealing conditions for nylon 6 fibers. Microinterferograms and curves are given for illustration.     

Synthesis, Characterization and Optimum Reaction Conditions of Oligo-N, N′-bis (2-hydroxy-1-naphthalidene) Thiosemicarbazone

The oxidative polycondenzation reaction conditions of N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone (HNTSC) using air oxygen, H₂O₂ and NaOCl were studied in an aqueous alkaline medium between 50–90°C. Oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone was characterized by ¹H-NMR, FT-IR, UV-Vis, size exclusion chromatography (SEC) and elemental analysis techniques. Solubility testing of oligomer was investigated using organic solvents such as DMF, THF, DMSO, methanol, ethanol, CHCl₃, CCl₄, toluene acetonitrile, ethyl acetate, concentrated H₂SO₄ and an aqueous alkaline solution. Using NaOCl, H₂O₂ and air O₂ oxidants, conversion to oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone (OHNTSC) of N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone was found to be 85, 80 and 76%, respectively, in an aqueous alkaline medium. According to the SEC analyses, the number-average molecular weight, weight-average molecular weight and polydispersity index values of OHNTSC synthesized were found to be 1050 gmol^–1 1715 gmol^–1 and 1.63, using NaOCl, and 2137, 2957 gmol^–1 and 1.38, using air O₂ and 2155 gmol^–1 4164 gmol^–1 and 1.93, using air H₂O₂, respectively. Also, TG analysis was shown to be unstable of oligo-N, N-bis (2-hydroxy-1-naphthalidene) thiosemicarbazone against thermo-oxidative decomposition. The weight loss of OHNTSC was found to be 97.29% at 900°C.