Homogeneous dispersion of SiO2 nanoparticles in an hydrosoluble polymeric network

The main difficulty still encountered in the elaboration of polymer/silica nanocomposites is the control of the nanoparticles dispersion homogeneity and the stability of the nanoparticle dispersion in the surrounding substance. The innovative point of this work is the elaboration of hybrid networks in aqueous solution performed with ASE (alkali swellable emulsion) thickeners grafted with silica nanoparticles. The thickening ability of the polymer should favour silica nanoparticles dispersion in fluid matrices. Two ASE copolymers were realised by copolymerisation in emulsion of MA (methacrylic acid) and EA (ethyl acrylate) and/or TFEM (trifluoroethyl methacrylate). The substitution of a part of EA by TFEM gave fluorinated ASE copolymers. Their free acid functions were then coupled with different ratio of amine functionalized silica nanoparticles to afford nanocomposites. The amounts of silica nanoparticles in the copolymers were determined by thermogravimetric experiments. Depending on the silica nanoparticles/copolymer ratio in basic aqueous solutions we achieved stable translucent gel like aqueous suspensions of silica nanoparticles containing 1 wt.% of the polymer/SiO₂ nanocomposite.     

Dielectric relaxation of monoesters based poly(styrene-co-maleic anhydride) copolymer

A series of alkyl-grafted copolymers based on styrene-maleic anhydride (SMA) copolymers were synthesized by esterification of SMA with several long chain normal aliphatic alcohols. The prepared copolymers were characterized by FT-IR and ¹H NMR and DSC. The dielectric behavior of these copolymers was investigated in the frequency 20–10⁵ Hz and temperature −40 to 180 °C ranges. Two relaxation processes were observed, α, and β-relaxation. The former is associated with the glass-rubber transition and is characterized by the Vogel–Fulcher–Tammann temperature dependence and the latter relaxation is related to the local motion of the ester side groups attached to the polymer backbone. The apparent activation energy for the β-relaxation was found to depend significantly on the alkyl chain length. The dielectric analysis of the β-relaxation process detected is discussed.     

Glass transition temperatures of copolymers from methyl methacrylate,styrene, and acrylonitrile: binary copolymers

By using a new theoretical glass transition temperature (T _g)–composition equation, T _g’s of statistic binary copolymers obtained from MMA, St and AN were investigated in this article. The copolymers were prepared by bulk copolymerization using azo-bis-isobutyronitrile (AIBN) as initiator. The compositions and T _g’s were determined by NMR and DSC, respectively. The monomer reactivity ratios were obtained by nonlinear fitting with Mayo–Lewis equation. Excellent fitting results were obtained when relations of T _g’s of MMA–St, MMA–AN, and St–AN copolymers with their compositions were investigated by using a new equation which assumed additivity of bond stiff energy (Liu et al. J Phys Chem B 112:93–99, 2008). This equation contains mole fractions of triads and T _g’s of corresponding periodic copolymers. Compared with the widely used Johnston equation and Barton equation, the new equation showed its superiority. Meanwhile, T _g’s of the assumed periodic copolymers that have not been acquired were tentatively predicted which may provide useful information.     

Synthesis and characterization of novel comb-type amphiphilic graft copolymers containing polypropylene and polyethylene glycol

Amphiphilic comb-type graft copolymers containing polypropylene (PP) and polyethylene glycol (PEG) have been prepared. Polypropylene-g-polyethylene glycol comb-type thermoplastic amphiphilic copolymers were synthesized by the reaction between chlorinated polypropylene and polyethylene glycol in the presence of a base via a “grafting to” technique. A series of graft copolymers containing PEGs with molecular weights of 600 and 2,000 Da in the range of 4–34 mol% PEG were obtained. The amphiphilic graft copolymers with PEG segments in range between 20 and 30 mol% PEG displayed good film properties with elongation at break 275–440%. The hydrophilicity of the amphiphilic copolymers increases with the increasing PEG content in the copolymer while the mechanical properties decrease. Therefore, PP-g-PEG2000 with PEG contents in the range of 20–30 mol% PEG should be useful for medical and industrial applications where good film properties are needed.     

Fumed silica filled poly(dimethylsiloxane-urea) segmented copolymers: Preparation and properties

Novel fumed silica filled thermoplastic poly(dimethylsiloxane-urea) (TPSU) segmented copolymers were synthesized and characterized. TPSU copolymers were prepared from a cycloaliphatic diisocyanate, aminopropyl terminated PDMS oligomers with number average molecular weights of 3,200, 10,800 and 31,500 g/mol and 2-methyl-1,5-diaminopentane chain extender. Two different types of fumed silica HDK H2000 (hydrophobic) and HDK N20 (hydrophilic) were utilized and incorporated into silicone-urea copolymers in amounts of 1-60% by weight. Influence of the silica type (hydrophilic versus hydrophobic), amount of silica loading and the PDMS soft segment molecular weight on the morphology, tensile properties and modulus-temperature behavior of the nanocomposites were determined. Major observations of this study were: (i) under the blending conditions used, incorporation of silica does not seem to interfere significantly with the hydrogen bonding between urea groups, (ii) incorporation of silica does not affect the glass transition temperature of PDMS, (iii) incorporation of silica influences the tensile and thermomechanical properties of silicone-urea segmented copolymers significantly, (iv) average molecular weight of the PDMS soft segment in the silicone-urea copolymer plays a critical role on the improvement of the tensile properties of the fumed silica/TPSU composites.     

Ring opening reactions of glycidyl methacrylate copolymers to introduce bulky organosilicon side chain substituents

Summary Glycidyl methacrylate (GMA) random copolymers with methyl acrylate (MA), ethyl acrylate (EA), n-butyl acrylate (BA), methyl methacrylate (MMA), ethyl methacrylate (EMA) and n-butyl methacrylate (BMA) were synthesized by solution free radical polymerizations, at 70±1 °C using α,α’-azobis(isobutyronitrile) as an initiator to give the copolymers I – VI in good yields. The copolymer compositions were obtained using related ¹H NMR spectra and the polydispersity indices of the copolymers determined using gel permeation chromatography (GPC). Tris(trimethylsilyl)methyl (Tsi=trisyl) groups were then covalently attached to the obtained copolymers as side chains by ring opening reaction between excess of TsiLi and expoxide groups of GMA units to give the copolymers I_Tsi – VI_Tsi in good yields. In the coupling reaction, the TsiLi reacted selectively with the epoxy groups of the backbone polymer rather than with the carbonyl groups of the backbone. This method of preparing functionalized silanes is limited by the readiness with which TsiLi abstracts a proton, if one is available, rather than attacks at carbon. In addition in the reaction with epoxides, the product alkoxide can transfer a silyl group from carbon to oxygen or ring opening polymerization. However these were shown not to occur at the conditions of interest here. The epoxy group possesses a higher reactivity for the TsiLi than the ester and chloromethyl groups. The ring opening reaction between the epoxy group and the TsiLi is simple and fast. All the resulted polymers were characterized by FT-IR and ¹H NMR spectroscopic techniques. The glass transition temperature (Tg) of all copolymers was determined by differential scanning calorimetry (DSC) apparatus. All the polymers containing trisyl groups showed a high glass transition temperature in comparison with unmodified copolymers (I – VI). Attaching the tris(trimethylsilyl)methyl group to macromolecular chain should lead to important modifications of polymer properties such as gas permeability and perm selectivity parameters.     

Homopolymer of 4-chloro-3-methyl Phenyl Methacrylate and its Copolymers with Butyl Methacrylate: Synthesis, Characterization, Reactivity Ratios and Antimicrobial Activity

The methacrylate monomer 4-chloro-3‐methyl phenyl methacrylate (CMPM) was synthesized by reacting 4-chloro-3‐methyl phenol with methacryloyl chloride. The homopolymer and various copolymers of CMPM with n-butyl methacrylate were synthesized by free-radical polymerization in toluene at 70°C using 2,2′-azobis(isobutyronitrile) as the initiator. The CMPM monomer was characterized by Fourier transform IR and ¹H-NMR studies. The copolymers were characterized by IR spectroscopy. The molecular weights (M _n and M _w) and the polydispersity index were obtained from gel permeation chromatography. The solubility and intrinsic viscosity of the homopolymer and the copolymers are also discussed here. The copolymer composition obtained from UV spectra led to the determination of reactivity ratios employing Fineman-Ross and Kelen-Tudos linearization methods. Thermogravimetric analyses of the homopolymer and the copolymers were carried out under a nitrogen atmosphere. The homopolymer and the copolymers prepared were tested for their antimicrobial activity against bacteria, fungi and yeasts.     

Lipase Catalyzed Synthesis of Poly(ε-Caprolactone)−Poly(Dimethylsiloxane)−Poly(ε-Caprolactone) Triblock Copolymers

Immobilized lipase B from Candida antarctica was used to synthesize copolymers of poly(ε-caprolactone) (PCL) with α,ω-(dihydroxy alkyl) terminated poly(dimethylsiloxane) (PDMS). The reactions were carried out in toluene with a 1:2 w/v ratio of the monomers to solvent at 70 oC. The PCL−PDMS−PCL triblock copolymer composition was varied by changing the feed ratio of the reactants [CL]/[PDMS] (80:20; 60:40; 40:60; 20:80 w/w, respectively). The enzymatically synthesized copolymers were characterized by GPC, FTIR, TGA, DSC and XRD. The successful synthesis of the copolymers was confirmed by the appearance of a single peak in all of the respective GPC chromatograms. An increased feed ratio of [CL]/[PDMS] produced an increase in the number-average molecular weight (M_n) of the copolymers from 4,400 g mol⁻¹ (20:80 w/w of [CL]/[PDMS]) to 13,950 g mol⁻¹ (80:20 w/w of [CL]/[PDMS]). The copolymers were shown by DSC and XRD to be semi-crystalline and the degree of crystallinity increased with an increase in the [CL]/[PDMS] feed ratio. The crystal structure in the copolymers was analogous to that of the PCL homopolymer. In enzymatic polymerization the recovery and reuse of the enzyme is highly desirable. When the lipase was recovered and reused for the copolymerization, higher molecular weight copolymers were obtained upon a second use. This appears to be due to an increased activity of the immobilized lipase following an opening up of the acrylic resin matrix in the organic medium. This improvement was not maintained for subsequent recycling of the lipase principally due to the disintegration of the acrylic resin matrix.     

Synthesis of poly(ɛ-caprolactone-b-isobutylene) diblock copolymer and poly(ɛ-caprolactone-b-isobutylene-b-ɛ-caprolactone) triblock copolymer

Summary Poly(isobutylene-b-ɛ-caprolactone) diblock and poly(ɛ-caprolactone-b-isobutylene-b-ɛ-caprolactone) triblock copolymers have been prepared and characterized. The synthesis involved the living cationic polymerization of IB, followed by capping with 1,1-diphenylethylene or 1,1-p-ditolylethylene and end-quenching with 1-methoxy-1-trimethylsiloxy-2-methyl-propene to yield methoxycarbonyl functional PIB. Hydroxyl end-functional PIB polymers were quantitatively obtained by the subsequent reduction of methoxycarbonyl end-functional PIB with LiAlH₄. The structure of hydroxyl end-functional PIBs was confirmed by ¹H NMR and IR spectroscopy. Poly(ɛ-caprolactone-b-isobutylene) diblock copolymers and poly(ɛ-caprolactone-b-isobutylene-b-ɛ-caprolactone) triblock copolymers were synthesized by the living cationic ring-opening polymerization of ɛ-caprolactone with hydroxyl end-functional PIB as macroinitiator in the presence of HCl•Et₂O via the “activated monomer mechanism”. The block copolymers exhibited close to theoretical M_ns and narrow molecular weight distributions. Received: 30 January 2002/Revised version: 19 February 2002/ Accepted: 19 February 2002     

Preparation and characterization of polyimide/silica/silver composite films

Polyimide/silica/silver hybrid films were prepared by the sol-gel method combined with in situ single-stage self-metallization technique. The structure of polyimide films in the thermal curing process and the influence of silica content on the migration and aggregation of silver particles to the surface of hybrid films were investigated. The hybrid films were characterized by transmission electron microscopy, dynamic mechanical thermal analysis, Fourier transform infrared spectroscopy, ultraviolet visible spectroscopy and mechanical measurements. The results indicated that there was no degradation of the polyimide matrix after the formation of silica and silver particles. Silica acted as the nucleus for the silver particles. With increasing silica content, more and more silver particles were kept in the hybrid films instead of being migrated onto the surface of the hybrid films and the reflections of hybrid films decreased gradually. __________ Translated from Acta Polymerica Sinica, 2007, (11): 1047–1051 [译自: 高分子学报     

Polyisobutylene based thermoplastic elastomers: VI. Poly(α-methylstyrene-b-isobutylene-b-α-methylstyrene) triblock copolymers by coupling of living poly (α-methylstyrene-b-isobutylene) diblock copolymers

Summary Poly(α-methylstyrene-b-isobutylene-b-α-methylstyrene) (PαMeSt-PIB-PαMePSt) triblock copolymers have been prepared via coupling of living diblock copolymers in a one pot procedure. The PαMeSt-PIB diblock copolymers were synthesized by living sequential cationic polymerization in methylcyclohexane (MeChx)/methylchloride (MeCl) solvent mixtures at −80 °C using BCl₃ for αMeSt polymerization and TiCl₄ for IB polymerization as coinitiators. The crossover efficiency, however, was only ∼57 %, due to intermolecular alkylation (indanyl ring formation) after the addition of TiCl₄. By modifying the PαMeSt end with a short segment of p-chloro-α-methylstyrene before IB addition the crossover efficiency was increased to 90 %. Coupling of the living block copolymers with 2,2-bis[4-(1-phenylethenyl)phenyl]propane (BDPEP) was rapid and gave ∼ 90 % efficiency. Received: 13 July 2000/Accepted: 3 August 2000     

Synthesis of PCL-b-PVAc block copolymers by combination of click chemistry, ROP, and RAFT polymerizations

Abstract  

The synthesis of new poly(ε-caprolactone)(PCL)-b-poly(vinyl acetate)(PVAc) block copolymers was investigated using different combinations of click chemistry, reversible addition-fragmentation transfer (RAFT), and ring opening polymerization (ROP) techniques. Two approaches, “coupling” and “macroinitiator” routes were studied. For the coupling approach, a chain transfer agent comprising an azide function was synthesized and used as initiator for the VAc polymerization. PCL containing an alkyne termination was obtained from a bifunctional initiator bearing an alkyne function and an hydroxyl group. These two functionalized precursors, PVAc and PCL, were coupled by a 1,3 cyclo addition reaction “click chemistry” in order to obtain the corresponding block copolymer. For the macroinitiator approach, PCL-b-PVAc block copolymers were synthesized using a two-step procedure: at first, a PCL macroinitiator with a xanthate end group was prepared by coordinated anionic polymerization of ε-caprolactone; then, the RAFT polymerization of VAc was initiated from the PCL, for the preparation of PCL-b-PVAc block copolymers. Whatever the method used, no detectable quantities of unreacted PVAc or PCL were observed. ¹H NMR and size exclusion chromatography analyses indicated successful synthesis of the block copolymers with well-defined structures.     

Synthesis of poly(ε-caprolactone)-poly(L-lactide) block copolymers by melt or solution sequential copolymerization using nontoxic dibutylmagnesium as initiator

Summary  Poly(ε-caprolactone)-poly(L-lactide) (PCL-PLLA) block copolymers were synthesized via melt or solution sequential copolymerization of ε-caprolactone (ε-CL) and L-lactide (L-LA) using nontoxic dibutylmagnesium as initiator. The formation of block structure was confirmed by ¹H-, ¹³C NMR, GPC, and FT-IR, it can be concluded that the block copolymers PCL-PLLA have been successfully synthesized by both melt and solution sequential copolymerization methods. Two melting endothermic peaks (T_m) during heating and two crystallization exothermal peaks (T_c) during cooling were observed in DSC curves. XRD patterns of the copolymers were approximately the superposition of both the PCL and PLLA homopolymers. The results indicated the coexistence of both PCL and PLLA crystalline microdomains, and the microphase separation took place in the block copolymers.     

Multiscale Modeling of the Morphology and Properties of Segmented Silicone-Urea Copolymers

Abstract  

Molecular dynamics and mesoscale dynamics simulation techniques were used to investigate the effect of hydrogen bonding on the microphase separation, morphology and various physicochemical properties of segmented silicone-urea copolymers. Model silicone-urea copolymers investigated were based on the stoichiometric combinations of α,ω-aminopropyl terminated polydimethylsiloxane (PDMS) oligomers with number average molecular weights ranging from 700 to 15,000 g/mole and bis(4-isocyanatocyclohexyl)methane (HMDI). Urea hard segment contents of the copolymers, which were determined by the PDMS molecular weight, were in 1.7–34% by weight range. Since no chain extenders were used, urea hard segments in all copolymers were of uniform length. Simulation results clearly demonstrated the presence of very good microphase separation in all silicone-urea copolymers, even for the copolymer with 1.7% by weight hard segment content. Experimentally reported enhanced properties of these materials were shown to stem from strong hydrogen bond interactions which leads to the aggregation of urea hard segments and reinforcement of the PDMS.     

Preparation of monodisperse PMMA particles by dispersion polymerization of MMA using poly(styrene-co-methacrylic acid) copolymer as a steric stabilizer

Dispersion polymerization of MMA was conducted using poly(styrene-co-methacrylic acid) copolymer as a steric stabilizer in an aqueous methanol medium. Various composition copolymers were easily prepared with a conventional radical polymerization by changing the monomer ratios of styrene to methacrylic acid, and were employed as a steric stabilizer for dispersion polymerization. The copolymers prepared with monomer ratios of 1.25–1.50 were found to be suitable steric stabilizers for dispersion polymerization. A very small amount of copolymer (0.6 wt% based on MMA) could act as a steric stabilizer effectively to obtain monodisperse PMMA particles. The particle size decreased with increasing the solvent polarity from 4 to 0.14 μm.     

Effect of α-MSt content in α-MSAN copolymer on the miscibility of PVC/α-MSAN blends

A series of α-methylstyrene, styrene and acrylonitrile(α-MSAN) copolymers with different α-methylstyrene (α-MSt) content were synthesized by altering α-MSt and St ratios with emulsion copolymerization method. By melt blending these copolymers with PVC resin and di-isooctyl phthalate (DOP), PVC/α-MSAN and PVC/α-MSAN/DOP blends were prepared. The miscibility and morphology of the blends were investigated by dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM). The miscibility of PVC/α-MSAN blends is substantially improved with the increasing α-MSt content in α-MSAN copolymer containing identical AN content and the blends show homogeneous morphology as the α-MSt content in α-MSAN copolymer is up to 22.5wt%. α-MSAN copolymer containing 37.5wt% α-MSt is fully miscible with PVC throughout the whole composition range. When DOP was introduced into the PVC/α-MSAN blends, a single Tanδ peak over room temperature in DMA detection is found as α-MSt content in α-MSAN copolymer is from 15 to 75 wt%, and morphology result also shows that the PVC and α-MSAN copolymer is miscible under the influence of DOP.     

Synthesis of poly [(methylsi1oxane)-co-(dimethylsilazane)] copolymers as precursors of ceramic materials

Summary A series of new crosslinked poly[(methylsiloxane)-co-(dimethylsilazane)] copolymers were synthesized by cationic ring opening polymerization of the cyclic monomers 1,3,5,7 – tetramethylcyclotetrasiloxane and 2,2,4,4,6,6 – hexamethylcyclotrisilazane. These copolymers contain different concentrations of methylsiloxane and silazane co-monomer units. The thermal stability is strongly related to the concentration of methylsiloxane co-units in the copolymers. The weight loss curve of the copolymers lies in a temperature range between its two homopolymers. FT-IR studies are in good agreement with the proposed structure, either for the copolymers or for the residual powder ceramic obtained by pyrolysis. Two cured processes (thermal and UV) were used. The pyrolysis of the copolymers were carried out under argon atmosphere at 1200°C and in air at 1000 °C. Kinetic decomposition parameters of the copolymers such as a pre-exponential factor, the decomposition reaction orders and the activation energies were determined. The molecular weights were determined by osmometry. Received: 21 August 2002/Revised version: 20 February 2003/ Accepted: 21 February 2003 Correspondence to Mario Rodríguez-Baeza     

Synthesis and micellization of an amphiphilic biodegradable β-cyclodextrin/poly(γ-benzyl L-glutamate) copolymer

β-Cyclodextrin/poly(γ-benzyl L-glutamate) (β-CD-PBLG) copolymers were synthesized by ring-opening polymerization of N-carboxy-γ-benzyl L-glutamate anhydride (BLG-NCA) in N,N-dimethylformamide(DMF) initiated by mono-6-amino-β-cyclodextrin(H₂N-β-CD). The structures of the copolymers were determined by IR, ¹H NMR and GPC. The fluorescence technique was used to determine the critical micelle concentration (CMC) of copolymer micelle solution. The diameter and the distribution of micelles were characterized by dynamic light scattering(DLS) and its shape was observed by transmission electron microscopy(TEM). The results showed that BLG-NCA could be initiated by H₂N-β-CD to produce copolymer. These copolymers showed an amphiphilic nature and could self-assemble into nano-micelles in water. The CMC of copolymer solution and the size of micelle reduced with the increasing of the proportion of hydrophobic parts. TEM images demonstrated the micelles are all spherical. Such copolymers could be expected to find applications in drug delivery systems and other biomedical domains.     

Copolymerization of 4-cyanophenyl acrylate with methyl methacrylate: synthesis, characterization and determination of monomer reactivity ratios

A novel acrylic monomer, 4-cyanophenyl acrylate (CPA) was synthesized by reacting 4-cyanophenol dissolved in methyl ethyl ketone with acryloyl chloride in the presence of triethylamine as a catalyst. Copolymers of CPA with methyl methacrylate (MMA) at different composition was prepared by free radical solution polymerization at 70 ± 1 °C using benzoyl peroxide as an initiator. The copolymers were characterized by FT-IR, ¹H-NMR and ¹³C-NMR spectroscopic techniques. The solubility tests were checked in various polar and non polar solvents. The molecular weight and polydispersity indices of the copolymers were estimated by using gel permeation chromatography. The glass transition temperature of the copolymers increases with increases MMA content. The thermal stability of the copolymer increases with increases in mole fraction of CPA content in the copolymer. The copolymer composition was determined by using ¹H-NMR spectra. The monomer reactivity ratios determined by the application of linearization methods such Fineman–Ross (r ₁ = 0.535, r ₂ = 0. 0.632), Kelen–Tudos (r ₁ = 0.422, r ₂ = 0.665) and extended Kelen–Tudos methods (r ₁ = 0.506, r ₂ = 0. 0.695).     

Sol–gel-processed silica/polydimethylsiloxane/calcium xerogels as polymeric matrices for Metronidazole delivery system

Silica, silica/polydimethylsiloxane and silica/polydimethylsiloxane/calcium xerogels were examined as polymeric carriers for the controlled release of drug—Metronidazole. Characterization assays comprised analysis of the matrix by Fourier transform infrared spectroscopy (FTIR), determining the specific surface area of solids (BET) and scanning electron microscope (SEM) techniques and further monitoring in the ultraviolet and visible light regions (UV–Vis) of the in vitro release of the drug over time. Using tetramethoxysilane (TMOS) as a precursor of silica matrix and polydimethylsiloxane (PDMS) and calcium ions as additives, xerogels with different morphology and physical properties were obtained. The applied modifications diminished the porosity and hydrophilicity of the silica matrix as well as reduced the release of drug. Based on the presented results of this study, it may be stated that applied xerogel matrices, pure silica (SiO₂) and modified silica (SiO₂–CaO, SiO₂–PDMS and SiO₂–CaO–PDMS), could be promising candidates for the formulation in local delivery systems.