Influence of chemical functionalization of carbon nanotubes on their dispersibility in alkyl methacrylate polymer matrix

Nanocomposites based on poly(methyl methacrylate) (PMMA) and poly(methyl methacrylate‐co‐octadecyl methacrylate) (M/O) matrices and four different types of multiwall carbon nanotubes: pristine, oxidized (MWCNT–COOH), methyl ester (MWCNT–COOCH₃), and dodecyl ester (MWCNT–COOC₁₂H₂₅) functionalized, were prepared in situ by radical (co)polymerization. The effectiveness of preparation of nanocomposites regarding dispersion and distribution of various MWCNT in polymer matrices was sized by Scanning electron microscopy. In case of PMMA matrix, the best dispersion and distribution were accomplished for MWCNT–COOCH₃ due to their chemical resemblance with polymer matrix. After the introduction of 10 mol % of octadecyl methacrylate in polymer matrix a fairly good dispersion and distribution of MWCNT–COOCH₃ were retained. The addition of 1 wt % of MWCNTs caused a significant reduction in the degree of polymerization of the PMMA matrix. But at the same time, the present MWCNTs increased storage modulus of PMMA nanocomposites except for dodecyl ester functionalized MWCNT. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46113.     

Low percolation threshold and high electrical conductivity in melt‐blended polycarbonate/multiwall carbon nanotube nanocomposites in the presence of poly(ε‐caprolactone)

This study focuses on the electrical properties of polycarbonate (PC)/poly(ε‐caprolactone) (PCL)‐multiwall carbon nanotube (MWCNT) nanocomposites. MWCNTs were incorporated into thermoplastic PC matrix by simple melt blending using biodegradable PCL based concentrates with MWCNT loadings (3.5 wt%). Because of the lower interfacial energy between MWCNT and PCL, the nanotubes remain in their excellent dispersion state into matrix polymer. Thus, electrical percolation in PC/PCL‐MWCNT nanocomposites was obtained at lower MWCNT loading rather than direct incorporation of MWCNT into PC matrix. AC and DC electrical conductivity of miscible PC/PCL‐MWCNT nanocomposites were studied in a broad frequency range, 10¹?10⁶ Hz and resulted in low percolation threshold (p_c) of 0.14 wt%, and the critical exponent (t) of 2.09 from the scaling law equation. The plot of logσ_DC versus p^?1/3 showed linear variation and indicated the existence of tunneling conduction among MWCNTs. At low MWCNT loading, the influence of large polymeric gaps between conducting clusters is the reason for the frequency dependent electrical conductivity. Transmission electron microscopy and field emission scanning electron microscopy showed that MWCNTs were homogeneously dispersed and developed a continuous interconnected network path throughout the matrix phase and miscibility behavior of the polymer blend. POLYM. ENG. SCI., 54:646–659, 2014. © 2013 Society of Plastics Engineers     

Microwave‐assisted synthesis and characterization of polyimide/functionalized MWCNT nanocomposites containing quinolyl moiety

Polyimide‐MWCNT nanocomposites were prepared by the reaction of a heterocyclic diamine monomer of bis(4‐amino‐3,5‐dimethylphenyl)‐2‐chloro‐3‐quinolylmethane (BACQM), pyromellitic dianhydride (PMDA) with unmodified MWCNT (MWCNT), acid‐functionalized MWCNT (acid‐MWCNT) or amine‐functionalized MWCNT (amine‐MWCNT) using microwave irradiation as well as by the conventional method. The structure of the monomer was confirmed by FTIR, ¹H‐NMR, and ¹³C‐NMR spectral techniques. The glass transition temperature (T_g) of the MWCNTs/polyimide nanocomposite was found to be higher than that of the unfilled polyimide system. The T_g's of both systems were higher when prepared with the microwave method than the conventional synthesis. The T_g's of the nanocomposites using acid and amine functionalized MWCNTs are greater than 300°C, in both methods. This is attributed to the presence of hydrogen bond and strong covalent bond in both the acid‐MWCNT/polyimide and amine‐MWCNT/polyimide systems. The morphological studies of the nanocomposites synthesized using microwave irradiation show that a distinct MWCNT nanofibrillar network is formed in the matrix when MWCNT or acid‐MWCNT is used. A homogeneous morphology, without distinct nanotube domains is seen when the amine‐MWCNT is covalently linked to the polymer. POLYM. COMPOS., 37:2417–2424, 2016. © 2015 Society of Plastics Engineers     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Low percolation threshold in polycarbonate/multiwalled carbon nanotubes nanocomposites through melt blending with poly(butylene terephthalate)

Here, we demonstrate an easy method for the preparation of highly electrically conductive polycarbonate (PC)/multiwalled carbon nanotubes (MWCNTs) nanocomposites in the presence of poly(butylene terephthalate) (PBT). In the presence of MWCNTs, PC and PBT formed a miscible blend, and the MWCNTs in the PC matrix were uniformly and homogeneously dispersed after the melt mixing of the PC and PBT–MWCNT mixture. Finally, when the proportion of the PC and PBT–MWCNT mixture in the blend/MWCNT nanocomposites was changed, an electrical conductivity of 6.87 × 10^?7 S/cm was obtained in the PC/PBT–MWCNT nanocomposites at an MWCNT loading as low as about 0.35 wt %. Transmission electron microscopy revealed a regular and homogeneous dispersion and distribution of the MWCNTs and formed a continuous conductive network pathway of MWCNTs throughout the matrix phase. The storage modulus and thermal stability of the PC were also enhanced by the presence of a small amount of MWCNTs in the nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Dynamic cure kinetics of epoxy/TiO2/MWCNT hybrid nanocomposites

The effect of multi-walled carbon nanotubes (MWCNTs) on cure kinetic parameters of the epoxy/amine/TiO₂ (1 wt%) resin system was studied dynamically at four heating rates using DTA. The presence of MWCNT in various amounts (0.1, 0.2, 0.4 and 0.6 wt%) neither retarded nor accelerated the cure reaction of the epoxy/amine/TiO₂ system in a considerable extent. Addition of MWCNTs increased the extent of cure of the corresponding nanocomposites, especially at higher contents up to 0.4 wt% MWCNT filled composite. However, increasing the MWCNT content to 0.6 wt% adversely affected the extent of cure due to nanoparticle agglomeration. The fracture surface morphology of the nanocomposites revealed that the cracks deviated on reaching the MWCNTs, while propagating in the polymer matrix. Fractional extent of conversion (α) was calculated using genetic algorithm. Flynn–Wall–Ozawa and Kissinger methods were used to analyze the kinetic parameters. The presence of MWCNTs did not affect the autocatalytic cure mechanism of epoxy/amine/TiO₂ resin system and also did not cause any considerable barrier effect on the curing process. Activation energy data fitted well in the cubic polynomial regression equations and the changes of E _a with respect to α proved the autocatalytic cure mechanism, being followed by all the MWCNT-containing epoxy-based hybrid nanocomposites.     

Electrical and mechanical tuning of 3D printed photopolymer–MWCNT nanocomposites through in situ dispersion

An electric field-assisted in situ dispersion of multiwall carbon nanotubes (MWCNTs) in polymer nanocomposites, fabricated through stereolithography three-dimensional (3D) printing technique, was demonstrated. The introduction of MWCNTs increased the elasticity modulus of the polymer resin by 77%. Furthermore, the use of an electric field for in situ MWCNT dispersion helped improving the average elongation at break of the samples with MWCNTs by 32%. The electric field also increased the ultimate tensile strength of the MWCNT reinforced nanocomposites by 42%. An increase of over 20% in the ultimate tensile strength of in situ dispersed MWCNT nanocomposites over the pure polymer material was observed. Finally, it was demonstrated that the magnitude and direction of the electrical conductivity of MWCNT nanocomposites can be engineered through the application of in situ electric fields during 3D printing. An increase of 50% in the electrical conductivity was observed when MWCNTs were introduced, while the application of the electric field further improved the electrical conductivity by 26%. The presented results demonstrated the feasibility of tuning both electrical and mechanical properties of MWCNT reinforced polymer nanocomposites using in situ electrical field-assisted 3D printing. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47600.     

Dispersion of multiwalled carbon nanotubes in polyacrylonitrile‐co‐starch copolymer matrix for enhancement of electrical,thermal, and gas barrier properties

Nanomaterials gained great importance on account of their wide range of applications in many areas. Carbon nanotubes (CNTs) exhibit exceptional electrical, thermal, gas barrier, and tensile properties and can therefore be used for the development of a new generation of composite materials. Functionalized multiwalled carbon nanotubes (MWCNTs) reinforced Polyacrylonitrile‐co‐starch nanocomposites were prepared by in situ polymerization technique. The structural property of PAN‐co‐starch/MWCNT nanocomposites was studied by X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The conductivity, tensile strength, and thermal properties of nanocomposites were measured as a function of MWCNT concentrations. The thermal stability, conductivity, and tensile strength of PAN‐co‐starch/MWCNT nanocomposites were improved with increasing concentration of MWCNTs. Oxygen barrier property of PAN‐co‐starch/MWCNT nanocomposites was calculated and it was found that, the property was reduced substantially with increase of MWCNTs proportion. The synthesized PAN‐co‐starch/MWCNT nanocomposites may used for electrostatically dissipative materials, aerospace or sporting goods, and electronic materials. © 2013 Society of Plastics Engineers     

The effect of multiwalled carbon nanotube dimensions on the morphology,mechanical, and electrical properties of melt mixed polypropylene‐based composites

The effect of multiwalled carbon nanotube (MWCNT) dimensions and surface modification on the morphology, mechanical reinforcement, and electrical properties of PP‐based composites, prepared by melt mixing, has been studied. The MWCNTs of small (d < 10 nm) and large (d = 40–60 nm) diameters with various intrinsic aspect ratios (L/d) have been used as filler. Transmission electron microscopy and very cold neutrons (VCN) scattering showed that both as‐received and surface modified small diameter MWCNT(1)s exhibit a strong tendency to bundle or cluster together in melt compared to both long MWCNT(3)s and short MWCNT(2)s large diameter nanotubes. The fractions of isolated nanotubes are higher and the mass‐fractal dimensions are lower for thick MWCNT‐based nanocomposites. The nanotubes of all types are heterogeneous nucleation sites for PP crystallization. The tensile and DMA testing results revealed that both long thick MWCNT(3)s with L/d ≈ 300 and thin MWCNT(1)s with highest intrinsic L/d > 1000 exhibit similar reinforcing effects, because drastically decreasing the effective aspect ratio (L/d)_eff of the thin flexibly nanotubes within polymer matrix. The nanocomposites based on the long large diameter MWCNT(3)s demonstrated the lowest percolation threshold equal to 1.5 vol % loading, highest dielectric and electromagnetic waves shielding properties. It was concluded that the choice of optimal diameter and length of MWCNTs is right approach to the improvement in the dispersion state and straightness of multiwelled carbon nanotubes in polymer melt as well as to enhancement of their efficiency as reinforcing and conductive nanosized filler. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal degradation kinetics of polyimide nanocomposites from different carbon nanofillers: Applicability of different theoretical models

In this study, the nanocomposites of polyimide (PI) with the nanofillers multiwalled carbon nanotube (MWCNT) and carbon nanofiber (CNF) were prepared by in situ polymerization technique. The thermal stability of the nanocomposites were investigated and discussed with respect to nanofillers type, concentration, and their functionality within the PI matrix. It is observed that there are 16 and 18 °C increment in thermal degradation temperature with the addition of 3 wt % MWCNT and CNF within the PI matrix, respectively. The thermal degradation kinetics of the nanocomposites were studied by Kissinger–Akahira–Sunose method, Flynn–Wall–Ozawa method, and Kim–Park method. The results show that these models are well fitted with the experimental data. It is found that the calculated activation energy increases with the increase in nanofillers loading and PI/CNF nanocomposites exhibit higher activation energy compared to PI/MWCNT composites at their similar loading. Moreover, the effect of nanofillers type and loading on the glass transition temperature of nanocomposites were also investigated in details. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45862.     

Preparation and thermal properties of multiwalled carbon nanotube/polybenzoxazine nanocomposites

In this study, we prepared nanocomposites comprising multiwalled carbon nanotubes (MWCNTs) and polybenzoxazine (PBZ). The MWCNTs were purified through microwave digestion to remove most of the amorphous carbon and metal impurities. After purification, MWCNTs were treated with H₂SO₄/HNO₃ (3 : 1) to introduce hydroxyl and carboxyl groups onto their surfaces. Raman spectroscopy revealed the percentage of nanotube content improved after prolonged microwave treatment, as evidenced by the decrease in the ratio of the D (1328 cm^?1) and G (1583 cm^?1) bands. For the untreated MWCNTs, the I_D/I_G ratio was 0.56. After microwave treatment for 40 min, the value decreased to 0.29, indicating that the percentage of nanotube content improved. Dynamic mechanical analyses (DMAs) revealed that the storage moduli and the T_gs of the MWCNTs/PBZ nanocomposites were higher than that of the pristine PBZ. This is due to the nanometer‐scale MWCNTs restricting the motion of the macromolecular chains in the nanocomposites. Transmission electron microscopy (TEM) image revealed that the MWCNTs were well dispersed within the PBZ matrix on the nanoscale when the MWCNT content was less than 2.0 phr. The coefficient of thermal expansion (CTE) of the nanocomposites decreased on increasing the MWCNTs content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystallinity of biodegradable polymers reinforced with functionalized carbon nanotubes

Well-dispersed multiwall carbon nanotubes (MWCNTs) were prepared by grafting poly(L-lactide-co-ε-caprolactone) (PLACL) biodegradable copolymer onto the sidewall of hydroxylated MWCNTs using oligomeric L-lactide (LA) and ε-caprolactone (CL). After preparation of MWCNT/PLACL composites, the effect of functionalized MWCNTs on crystallinity of PLACL was investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and polarized light optical microscopy (POM). The surface functionalization effectively improved the dispersion and adhesion of MWCNTs which acted as reinforcing filler in the PLACL polymer matrix and hence improved the physical and thermomechanical properties of the nanocomposites. The glass transition temperature (T _g) and the crystallinity of nanocomposites decreased in comparison with those of neat PLACL when the concentration of functionalized MWCNTs in nanocomposites was 0.5 wt%. With further increment in concentration of functionalized MWCNTs, the T _g of composites increased until the T _g of neat PLACL, and also the crystallinity of composites increased. The functionalized MWCNTs have no significant effect on the melting point of nanocomposites. The MWCNTs acted as heterogeneous nucleation points and increased the lamella size and therefore the crystallinity of PLACL. Furthermore, the larger agglomerated clusters of both kinds of MWCNTs (i.e., MWCNT-grafted-PLACL and pristine MWCNTs) are more effective than small clusters as nucleation points for growing the spherulites.     

Field emission of MWCNTs/PANi nanocomposites prepared by ex‐situ and in‐situ polymerization methods

The present work describes the field‐emission properties of multiwalled carbon nanotubes (MWCNTs) coated with conducting polymer polyaniline (PANi). MWCNTs/PANi nanocomposites have been prepared by ex‐ situ polymerization methods and inex‐ situ chemical polymerization and are analyzed by SEM and Raman spectroscopy. It is fairly clear from SEM images that PANi is coated on the surface of MWCNT. SEM image of PANi powder also shows that the powder obtained is PANi nanofibers. It is also observed from SEM images that the shell diameter of MWCNTs depends on PANi content in thenanocomposites. The average outer diameter of MWCNTs increases from 7–15 to 50–80 nm upon PANi coating. Field‐emission study shows that although there is decrease in the value of turnex‐on field E_to and increase in the value field enhancement factor β of the nanocomposites as we go from direct solid‐state mixing method to inex‐ situ chemical polymerization method, the parameters obtained by inex‐ situ polymerization chemical method shows superior field emission. The turn‐on field of the nanocomposites are between 2.5 and 4.5 V/μm and the field enhancement factors are significantly high, between 1.2 × 10³ and 9.2 × 10³ while. PANi nanofibers does not show any field emission. POLYM. COMPOS. 34:1298–1305, 2013. © 2013 Society of Plastics Engineers     

The effects of triethylenetetramine grafting of multi‐walled carbon nanotubes on its dispersion,filler‐matrix interfacial interaction and the thermal properties of epoxy nanocomposites

This study describes the influence of triethylenetetramine (TETA) grafting of multi‐walled carbon nanotubes (MWCNTs) on the dispersion state, interfacial interaction, and thermal properties of epoxy nanocomposites. MWCNTs were first treated by a 3:1 (v/v) mixture of concentrated H₂SO₄/HNO₃, and then TETA grafting was performed. Chemically grafted MWCNT/bisphenol‐A glycidol ether epoxy resin/2‐ethyl‐4‐methylimidazole nanocomposites were prepared. TETA grafting could establish the connection of MWCNTs to the epoxy matrix and transform the smooth and nonreactive MWCNT surface into a hybrid material that possesses the characteristics of both MWCNTs and TETA, which facilitates homogeneous dispersion of MWCNTs and improves nanotube‐epoxy interfacial interaction. Therefore, the impact property, glass transition temperature, thermal stability, and thermal conductivity of epoxy nanocomposites are enhanced. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Improved impact strength of epoxy by the addition of functionalized multiwalled carbon nanotubes and reactive diluent

Multiwalled carbon nanotubes (MWCNTs), both oxidized and amine functionalized (triethylenetetramine—TETA), have been used to improve the mechanical properties of nanocomposites based on epoxy resin. The TGA and XPS analysis allowed the evaluation of the degree of chemical modification on MWCNTs. Nanocomposites were manufactured by a three‐roll milling process with 0.1, 0.5, and 1.0 wt % of MWCNT–COOH and MWCNT–COTETA. A series of nanocomposites with 5.0 wt % of reactive diluent was also prepared. Tensile and impact tests were conducted to evaluate the effects of the nanofillers and diluent on the mechanical properties of the nanocomposites. The results showed higher gains (258% increase) in the impact strength for nanocomposites manufactured with aminated MWCNTs. Optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to investigate the overall filler distribution, the dispersion of individual nanotubes, and the interface adhesion on the nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42587.     

Synthesis of New PI/MWCNT Containing Sulfone Groups via In Situ Polymerization: Study on Thermal,Electrical, and Optical Properties

New series of polyimide (PI) nanocomposites reinforced with three different amounts of multiwalled carbon nanotubes (MWCNT; 0.5, 1, and 3 wt%) were prepared by casting, evaporation and thermal imidization. Homogeneous dispersion of MWCNT in PI matrix was investigated by transmission electron microscopy. The effects of MWCNT on the thermal properties of the PI were investigated by thermogravimetric analysis. The results showed that the thermal stability of the nanocomposites enhanced with the increasing MWCNTs content. The resultant PI/MWCNT nanocomposites were electrically conductive with significant conductivity enhancement at 3 wt% MWCNT, which is favorable for many practical uses.     

Reduction of percolation threshold through double percolation in melt‐blended polycarbonate/acrylonitrile butadiene styrene/multiwall carbon nanotubes elastomer nanocomposites

We demonstrate a method that involves melt blending of polycarbonate (PC) and melt‐blended acrylonitrile butadiene styrene (ABS) with multiwall carbon nanotubes (MWCNTs) to prepare electrically conducting PC/MWCNT nanocomposites at significantly low MWCNT loading. The partial solubility of ABS in PC led to a selective dispersion of the MWCNTs in the ABS phase after melt‐blending PC and ABS. Thus, a sudden rise in electrical conductivity (∼10⁸ orders of magnitude) of the nanocomposites was found at 0.328 vol% of MWCNT, which was explained in terms of double percolation phenomena. By optimizing the ratio of PC and the ABS–MWCNT mixture, an electrical conductivity of 5.58 × 10⁻⁵ and 7.23 × 10⁻³ S cm⁻¹ was achieved in the nanocomposites with MWCNT loading as low as 0.458 and 1.188 vol%, respectively. Transmission electron microscopy revealed a good dispersion and distribution of the MWCNTs in the ABS phase, leading to the formation of continuous MWCNT network structure throughout the matrix even at very low MWCNT loading. Storage modulus and thermal stability of the PC were also increased by the presence of a small amount of MWCNTs in the nanocomposites.POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Electrical conductivity behavior of epoxy matrix nanocomposites with simultaneous dispersion of carbon nanotubes and clays

In this work, nanocomposites with simultaneous dispersion of multiwalled carbon nanotubes (MWCNT) and montmorillonite clays in an epoxy matrix were prepared by in situ polymerization. A high energy sonication was employed as the dispersion method, without the aid of solvents in the process. The simultaneous dispersion of clays with carbon nanotubes (CNT) in different polymeric matrices has shown a synergic potential of increasing mechanical properties and electrical conductivity. Two different montmorillonite clays were used: a natural (MMT‐Na⁺) and an organoclay (MMT‐30B). The nanocomposites had their electrical conductivity (σ) and dielectric constant (ε_r) measured by impedance spectroscopy. The sharp increase in electrical conductivity was found between 0.10 and 0.25 wt% of the MWCNTs. Transmission electron microscopy (TEM) of the samples showed a lower tendency of MWCNT segregation on the MMT‐30B clay surface, which is connected to intercalation/exfoliation in the matrix, that generates less free volume available for MWCNTs in the epoxy matrix. Data from electrical measurement showed that simultaneously adding organoclay reduces the electrical conduction in the nanocomposite. Moreover, conductivity and permittivity dispersion in low frequency suggest agglomeration of nanotubes surrounding the natural clay (MMT‐Na⁺) particles, which is confirmed by TEM. POLYM. COMPOS., 37:1603–1611, 2016. © 2014 Society of Plastics Engineers     

Antistatic packaging based on PTT/PTT-g-MA/ABS/MWCNT nanocomposites: Effect of the chemical functionalization of MWCNTs

Polymer/carbon nanotube nanocomposites have attracted high interest for a wide spectrum of applications, including antistatic packaging used to protect electronic devices against electrostatic discharge. Polytrimethylene terephthalate (PTT)/maleic-anhydride-grafted PTT (PTT-g-MA)/acrylonitrile butadiene styrene (ABS) blend-based multiwall carbon nanotubes (MWCNTs) nanocomposites were prepared through extrusion. It was conducted chemical functionalization on the MWCNTs by oxidation using nitric acid to introduce functional groups. The effect of the amount (0.5 or 1.0 wt%) and functionalization of MWCNTs on the nanocomposites was investigated. Despite the poor barrier properties of PTT/PTT-g-MA/ABS/MWCNT nanocomposites due to the presence of voids confirmed by scanning electron microscopy (SEM), the nanocomposites with functionalized MWCNT (MWCNTf) showed excellent barrier properties, indicating that the functionalization process improved the interaction between the MWCNTs and the matrix. The addition of MWCNTs into PTT/PTT-g-MA/ABS blend decreased the electrical resistivity by eight orders of magnitude. The use of MWCNTf may still disrupt the electrical network pathway and slightly decreasing the electrical resistivity, but the nanocomposites present the desired properties required for antistatic packaging.     

Remarkable change in the broadband electrical behavior of poly(vinylidene fluoride)–multiwalled carbon nanotube nanocomposites with the use of different processing routes

Poly(vinylidene fluoride) (PVDF) nanocomposites have plenty of applications in the electronic realm. In this study, we produced nanocomposites based on PVDF and multiwalled carbon nanotubes (MWCNTs), with various MWCNT loadings, using three different processing routes: solution mixing, melt mixing, and electrospinning. The broadband electrical behavior of these nanocomposites was studied and compared via impedance spectroscopy. The morphologies of the nanocomposites were characterized by transmission electron microscopy and scanning electron microscopy. The results reveal that the electrical behaviors of the samples were completely different according to the processing route used. Solution mixing was the most suitable method for producing nanocomposites with the highest conductivities, at low MWCNT loadings, whereas electrospinning was the most suitable method for producing nanocomposites with the lowest dielectric permittivity. These differences were attributed to the different arrangements of the MWCNTs caused by the different processes. Although the solution-mixed samples exhibited long and twisted MWCNTs, the melt-mixed samples had shorter MWCNTs, and the electrospun samples had MWCNTs embedded and aligned inside the insulating polymer nanofibers. Thus, these results project a vast horizon for tailoring the structure and thereby the broadband electrical behavior of PVDF–MWCNT nanocomposites for different types of applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47409.