Luminescent characteristics of LiCaBO3：Eu^3＋ phosphor for white light emitting diode

LiCaBO3:Eu3+ phosphor was synthesized by high solid-state reaction method, and its luminescent characteristics were investigated. The emission and excitation spectra of LiCaBO3:Eu3+ phosphors exhibited that the phosphors could be effectively excited by near ultraviolet (400 nm) and blue (470 nm) light, and emitted red light. The effect of Eu3+ concentration on the emission spectrum of LiCaBO3:Eu3+ phos-phor was studied. The results showed that the emission intensity increased with increasing Eu3～ concentration, and then decreased because of concentration quenching. It reached the maximum at 3mol.% Eu3+, and the concentration self-quenching mechanism was the d-d interaction according to the Dexter theory. Under the conditions of charge compensator Li+, Na+ or K+ incorporated in LiCaBO3, the emission intensities of LiCaBO3:Eu3+ phosphor were enhanced.     

Synthesis and luminescence characteristics of terbium（III） activated NaSrBO3

The thermoluminescence (TL) and photoluminescence (PL) properties of the phosphor NaSrBO 3 :Tb 3+ were reported and discussed. The combustion technique was used for the synthesis of polycrystalline samples of NaSrBO 3 :Tb 3+ . The TL glow curve of the compound had a simple structure with a single peak at 434 K. TL sensitivity of the phosphor was found to be more than that of (LiF:Mg,Cu,P). The TL glow curve was studied as a function of concentration of dopant and dose of gamma ray irradiation. The kinetic parameters of the thermoluminescence of NaSrBO 3 : Tb 3+ were calculated employing the peak shape method. The photoluminescence (PL) properties of Tb 3+ doped in NaSrBO 3 were studied over the 200-400 nm excitation range. The excitation spectra of NaSrBO 3 :Tb 3+ consisted of single narrow band peaking at about 236 nm. The emission spectra monitored at 236 nm excitation consisted of a series of sharp lines peaking at 489, 544, 586 and 622 nm corresponding to the 5 D 4 → 7 F j (j=3,4,5,6) transitions within the 4f 8 configurations of Tb 3+ .     

表面活性剂对ZnWO4：Tb3+绿色荧光粉发光性能的影响

采用水热法合成应用于荧光灯的绿色荧光粉 ZnWO4：Tb3+。通过X 射线粉末衍射分析仪（XRD）,扫描电子显微镜（SEM）和荧光光谱仪,系统考察不同表面活性剂条件下合成的ZnWO4：Tb3+绿色荧光粉。结果表明,不同表面活性剂条件下,采用水热法合成的产品均为纯ZnWO4结构,Tb3+掺杂并不改变钨酸锌结构;荧光光谱仪对样品的激发和发射以及荧光衰减曲线测定表明,表面活性剂PEG-2000条件下合成的荧光粉,其发光强度增强最有效,采用PVP 为表面活性剂合成ZnWO4：Tb3+的荧光粉寿命较采用PEG-2000和CTAB 为表面活性剂合成的长。综合发光强度和荧光寿命的影响,选PVP为表面活性剂最佳。     

Hydrothermal synthesis,structure study and luminescent properties of YbPO₄:Tb³⁺ nanoparticles

YbPO4:Tb3+ were synthesized by mild hydrothermal method.The luminescent properties,morphologies and structure of the obtained powders were characterized by photoluminescence(PL) spectra,FESEM,X-ray diffractometer(XRD) and FTIR.The results showed that the prepared YbPO4:Tb3+ nanoparticles were pure tetragonal phase and the average grain size varied with increasing of Tb3+ concentration.Hydrothermal temperature was revealed to be the key factor to enhance the emission intensity of YbPO4:Tb3+ phosphors.The spherical nanoparticles could be effectively excited by near UV(369 nm) light and exhibited green performance at 543 nm(5D4→7F5),489 nm(5D4→7F6) and 586 nm(5D4→7F4).The CIE chromaticity was calculated to be x=0.298,y=0.560.The YbPO4:Tb3+ nanoparticles exhibited potential to act as UV absorber for solar cells to enhance the conversion efficiency.     

Luminescent properties of Ba3Gd（BO3）3：Eu^3＋ phosphor for white LED applications

Luminescent material Ba3Gd(BO3)3 doped with Eu3+ ion was prepared by high temperature solid-state method. The preparing conditions, luminescent properties, and particle morphology of Ba3Gd(BO3)3:Eu3 + phosphor were studied with X-ray diffraction (XRD), fluorescence spectroscopy, and scanning electron microscopy (SEM). The results obtained by XRD showed that pure phase of Ba3Gd(BO3)3 was obtained at 1000℃. Images from SEM displayed that the particles of Ba3Gd(BO3)3:Eu3+ phosphor had a spherical shape with an average diameter of about 200-400 nm. The luminescence spectra showed that Ba3Gd(BO3)3:Eu3+ phosphor was effectively excited by the near ultraviolet (UV) light (396 nm) and blue light (466 nm). The main emission peaks of Ba3Gd(BO3)3:Eu3+ phosphor were assigned to the supersensitive transition 5D0-7F2 (611 and 616 nm) of Eu3+ ion when samples were excited at 255 and 396 nm, respectively, and the luminescent intensity of Ba3Gd(BO3)3:Eu3+ at 611 and 616 nm reached to the maximum when the doped content of Eu3+ ion was 10mol.%. Therefore, this phosphor could be a promising red component for possible applications in the field of white LED.     

Luminescent properties of SrSi2N2O2:Ce3+,Tb3+-a potential phosphor for white light emitting diodes

Ce3+ and Tb3+ co-doped SrSi2N2O2 phosphors were prepared by solid-state reaction. The X-ray diffraction pattern exhibited that the phosphor consisted mainly of oxygen-rich SrSi2N2O2. The optical properties of SrSi2N2O2:Ce3+, SrSi2N2O2:Tb3+ and SrSi2N2O2:Ce3+,Tb3+ were studied, respectively. The emission intensity of Tb3+ at 541 nm was remarkably enhanced by Ce3+ in SrSi2N2O2:Ce3+,Tb3+ phosphor, which was attributed to the energy transfer from Ce3+ to Tb3+. The chromaticity coordinates of phosphors were investigated as a function of Tb3+ concentration. When the Ce3+ and Tb3+ concentrations were 0.02 and 0.18 mol per formula unit, respectively, the chromaticity coordinate was (0.257, 0.337) in the CIE 1931 chromaticity diagram. SrSi2N2O2Ce3+,Tb3+ phosphors could be used for white light emitting diodes.     

溶胶-凝胶法制备Sr2SiO4:Tb3+绿色荧光粉及其发光性能

采用溶胶-凝胶法合成了一系列适合紫外-近紫外激发的(1-X)Sr₂SiO₄:XTb3+(X=0,0.01,0.02,0.03,0.04,0.05,0.06)绿色荧光粉,并采用X射线衍射(XRD)、扫描电子显微镜(SEM)和荧光光谱(PL)研究了样品的结构及发光性能.由XRD的检测结果可知,合成样品属于单斜晶系的β-Sr₂SiO₄相.由SEM图可知,所有样品都呈无规则块状结构.当监测波长为546 nm,样品的激发光谱的主峰位于370 nm处,属于Tb3+的4f-4f特征跃迁吸收.当激发波长分别为285 nm和250 nm,所有样品在488 nm,547 nm,586 nm,623 nm处都出现了1个强发射峰,分别对应Tb3+的5D₄→7F₆、5D₄→7F₅、5D₄→7F₄和5D₄→7F₃电子跃迁.最强发射峰位于547 nm处,呈现特征为绿光发射.随Tb3+掺杂量增大,发射强度呈现出先增大后减小的变化趋势,即存在浓度猝灭效应.当Tb3+掺杂量为X=0.03时,样品的发光强度最大.      

Sol-gel processed Ce^3＋, Tb^3＋ codoped white emitting phosphors in Sr2Al2SiO7

Sr2Al2SiO7：Ce^3＋, Tb^3＋ white emitting phosphors were fabricated using the sol-gel method. X-Ray Powder Diffraction （XRD） analysis confirmed the formation of Sr2Al2SiO7：Ce^3＋, Tb^3＋. Scanning Electron Microscopy （SEM） observation indicated that the microstructure of the phosphor consisted of regular fine grains with an average size of about 0.5-1 μm. Luminescence properties were analyzed by measuring the photoluminescence spectra. The Ce^3＋, Tb^3＋-codoped Sr2Al2SiO7 phosphors showed four main emission peaks： one at 414 nm for Ce^3＋ and three at 482, 543, and 588 nm for Tb^3＋. The emission spectra of the samples with different doping concentrations showed that the Tb^3＋ emission was dominant because of the persistent energy transfer from Ce^3＋. The decay characteristic was better than that prepared by the solid-state process in the comparable condition. The codoped phosphor displayed long persistent white phosphorescence.     

Photoluminescence characterization and energy transfer of NaBa1-x-yPO4：xCe3＋, yTb3＋ phosphors

A series of NaBa1-x-yPO4: xCe3+, yTb3+ phosphors were synthesized by solid-state reaction method. The crystal structure, photoluminescence emission and excitation spectra and decay times of the phosphors were carefully investigated. The results revealed that an efficient energy transfer occurred from Ce3+ to Tb3+ ions in NaBaPO4 host by means of dipole-dipole interactions and the critical distance of the energy transfer was about 0.638 nm. Moreover, the phosphor emitted strong green emission under UV excitation, indicating that the phosphors are potentially useful as a highly efficient, green-emitting phosphor.     

Energy transfer in Tb~（3＋）,Yb~（3＋） codoped Lu_2O_3 near-infrared downconversion nanophosphors

Tb3+ and Yb3+ codoped Lu2O3 nanophosphors were synthesized by the reverse-strike co-precipitation method. The obtained Lu2O3:Tb3+,Yb3+ nanophosphors were characterized by X-ray diffraction (XRD) and photoluminescence (PL) spectra. The XRD results showed that all the prepared nanophosphors could be readily indexed to pure cubic phase of Lu2O3 and indicated good crystallinity. The Tb3+→Yb3+ energy transfer mechanisms in the UV-blue region in Lu2O3 nanophosphors were investigated. The experimental results showed that the strong visible emission around 543 nm from Tb3+ (5D4→7F5) and near-infrared (NIR) emission around 973 nm from Yb3+ (2F5/2→2F7/2) of Lu2O3:Tb3+,Yb3+ nanophosphors were observed under ultraviolet light excitation, respectively. Tb3+ could be effectively excited up to its 4f75d1 state and relaxed down to the 5D4 level, from which the energy was transferred cooperatively to two neighboring Yb3+. The Yb3+ concentration dependent luminescent properties and lifetimes of both the visible and NIR emissions were also studied. The lifetime of the visible emission decreased with the increase of Yb3+ concentration, verifying the efficient energy transfer from the Tb3+ to the Yb3+. Cooperative energy transfer (CET) from Tb3+ to Yb3+ was discussed as a possible mechanism for the near-infrared emission. When doped concentrations were 1 mol.% Tb3+ and 2 mol.% Yb3+, the intensity of NIR emission was the strongest.     

Luminescence properties of BaAl₁₂O₁₉:Tb,Ce and energy transfer between Ce³⁺,Tb³⁺

BaAl12O19:Tb,Ce phosphors were prepared by sol-gel technique,the crystalline structures of samples characterized by XRD,and the luminescence properties and energy transfer between Ce3+ and Tb3+ were investigated.The results indicated that the emission intensity and the excitation wavelength range of Tb3+ increased when Ce3+ was doped.It demonstrated that the Ce3+ added in the BaAl12O19:Tb could deliver energy to Tb3+,and Ce3+ was not luminous by itself.The relative emission intensity of Tb3+ at wavelength of 548 nm was the strongest by Tb3+/Ce3+ ratio of 2:1,when excited at 310 nm,which was the characteristic adsorption wavelength of Ce3+.     

Combustion synthesis of Ce~（3＋）, Eu~（3＋） and Dy~（3＋） activated NaCaPO_4 phosphors

The preparation of NaCaPO4 doped with rare earth (RE) ions Ce3+, Eu3+ and Dy3+ by combustion method was described. Under UV excitation (251 nm) of NaCaPO4:Ce3+ showsd emission (367 nm) in UV range. When NaCaPO4:Dy3+ phosphor was excited at 349 nm, the emission spectrum showed intense bands at 482 nm (blue) and 576 nm (yellow). In Eu activated NaCaPO4 phosphor, the emission spectrum showed a dominant peak at 594 nm (orange) while others were at 614 and 621 nm (red) when excited at 393 nm. The prepared phosph...     

铽在硫氧化镧基质中的光致发光

采用高温固相反应法制备了La2O2S∶Tb3+、La2O2S∶Tb3+,RE3+(RE=Dy,Gd,Ce,Sm)荧光粉样品并进行了相关表征。结果表明,合成样品的晶体结构与La2O2S相同,为六方晶系;荧光粉颗粒的形貌多为长方形片状;发射光谱由494 nm、545 nm、587 nm、622 nm的一系列锐发射峰组成。研究发现Tb3+的掺杂浓度对样品主发射峰545 nm的发光强度影响很大,且在摩尔分数x(Tb3+)=0.02时达到最强。稀土离子Dy3+、Gd3+对La2O2S∶Tb3+荧光粉的发光有明显的敏化作用。     

Thermoluminescence characteristics of NaSr4（BO3）3：Ce^3＋ under β-ray irradiation

The thermoluminescence (TL) properties of Ce3+ doped NaSr4(BO3)3 phosphor under the β-ray irradiation were reported. The polycrystalline sample was synthesized by high temperature solid-state reaction. The TL glow curve of NaSr4(BO3)3:Ce3+ phosphor was com-posed of only one peak. TL kinetic parameters of NaSr4(BO3)3:Ce3+ were deduced by the peak shape method, the activation energy (E) was 0.590 eV and the frequency factor was 1.008×106s-1. TL dose response was linear in the range of measurement. The 3-dimensional (3D) TL emission spectrum was also recorded, the emission spectrum consisted of two bands located at 441 and 479 nm respectively, corresponding to the characteristic 4f05d1→2F(5/2,7/2) transitions of the Ce3+ ion. The fading behavior of the NaSr4(BO3)3:Ce3+ phosphor over a period of 15 d was also studied.     

白光LED用LaPO4:Eu3+红色荧光粉的合成与表征

利用水热法制备了性能稳定的红色荧光粉LaPO4:Eu3+,同时研究了不同的Eu3+浓度、煅烧温度对荧光粉发光性能的影响.通过X射线粉末衍射(XRD)和扫描电子显微镜(SEM)来表征荧光粉的晶体结构和颗粒大小及形貌;用激发光谱和发射光谱以及荧光衰减曲线来表征荧光粉的荧光性能.结果表明:未煅烧时前躯体主要是六方晶相LaPO4·0.5H2O,煅烧温度在900℃时,所制备样品为单斜相LaPO4:Eu3+;SEM图像显示5 at.%Eu3+掺杂LaPO4呈椭球形,颗粒长约为500 nm,宽约为300 nm.最大发射波长和激发波长分别为592 nm和393 nm,发射光谱中592 nm和612 nm的发射峰对应的是Eu3+离子的5D0→7F1和5D0→7F2跃迁.其荧光寿命为3.32 ms.     

Synthesis and luminescence properties of CeF3：Tb3＋ nanodisks via ultrasound assisted ionic liquid method

CeF3 and CeF3：Tb3＋ nanocrystals were successfully synthesized by the ultrasound assisted ionic liquid （IL） method at room temperature. X-ray diffraction （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, selected area electron diffraction （SAED）, high-resolution transmission electron micrographs （HRTEM） and photoluminescence （PL） spectra were employed to characterize the nanocrystals. The results of XRD indicated that the obtained samples crystallized well with a hexagonal phase crystal structure. SEM and TEM images demonstrated that the obtained CeF3：Tb3＋ nanocrystals had a discoid shapein the presence of ultrasound and IL, whereas only granular nanoparticles were obtained by magnetic stirring. The possible formation mechanisms of the crystal growth were proposed. The PL spectra of the CeF3：Tb3＋ nanodisks exhibited a strong green emission when excited at 254 nm. Furthermore, the photoluminescence intensity of CeF3：Tb3＋ of the discoid particles was largely improved com-pared with that of the granular nanoparticles.     

Luminescent characteristics of Ba3Y2（BO3）4：Eu^3＋ phosphor for white LED

The Ba3Y2（BO3）4：Eu^3＋ phosphor was synthesized using a high temperature solid-state reaction method and the luminescent characteristics were investigated. The emission spectrum exhibited one strong red emission at 613 nm, corresponding to the electric dipole 5D0-TF2 transition of Eu^3＋, under 365 nm excitation. The excitation spectrum of 613 nm indicated that the Ba3Y2（BO3）n：Eu^3＋ phosphor was effectively excited by ultraviolet （UV） （254, 365 and 400 nm） and blue （470 nm） light. The effect of Eu^3＋ concentration on the 613 nm emission of the Ba3Y2（BO3）n：Eu^3＋ phosphor was measured. The results showed that the emission intensity increased with increasing Eu^3＋ concentration, and then decreased. The CIE color coordinates of Ba3Y2（BO3）4：Eu^3＋ phosphor were x=0.641 and y=0.359 at 15 mol.% Eu^3＋.     

溶胶-凝胶法制备Ca3Al2O6：Eu3+红色荧光粉及其发光性能

采用溶胶-凝胶法合成Ca3Al2O6：Eu3+红色荧光粉,通过XRD、SEM、荧光光谱分别对样品的结构、形貌以及发光性能进行表征,讨论煅烧温度、Eu3+掺杂浓度以及电荷补偿剂对样品发光性能的影响.结果表明：实验所得样品的结构与Ca3Al2O6相同,Eu3+掺杂并没有改变其晶体结构.合成的荧光粉在394 nm近紫外光激发下发出615 nm明亮的红光.样品的红光强度随着煅烧温度的升高先增加后减弱,最佳烧结温度为1200℃.同样红光强度也随着Eu3+掺杂浓度的增加先增加后减弱,最佳Eu3+掺杂浓度为4%（摩尔分数）.加入电荷补偿剂后样品的发光强度均增强,其中加入K+后发光增强的效果最显著.该铝酸盐红色荧光粉性质稳定,在白光LED近紫外芯片激发中具有潜在的应用.     

Doped Organic Electroluminescence from a Novel Rare Earth Complex Tb （3-metho） 3 phen

A novel rare earth complex Tb (3-metho)3phen was synthesized and characterized. The complex was doped into PVK to improve the conductivity and film-forming property of Tb(3-metho) 3phen. A device with a structure of ITO/PVK: Tb(3-metho)3phen/Al was fabricated to study the eleetrolumineseent properties of Tb(3-metho) 3 phen. And the optoluminescent and AFM properties of this device were also studied, which proved the existence of energy transfer from PVK to Tb(3-metho)3phen. As a result, a pure green emission with sharp spectral band at 547.5 nm was observed.     

Luminescent properties and energy transfer of color-tunable Sr3Y2（SiO3）6：Ce3＋,Tb3＋ phosphors

Phosphors with controlled emission spectra are of great interest due to their application for white light emitting diodes.Herein, a new class of Sr3Y2（SiO3）6：Ce3＋,Tb3＋ phosphors were synthesized by a facile sol-gel combustion method. The phase structure,morphology, and luminescence properties of the phosphors were characterized by using powder X-ray diffraction（XRD）, scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, and photoluminescence excitation and emission spectra,respectively. The results on luminescence properties indicated that co-doped Ce3＋ ions served as UV-light sensitizers with excitation energy partially transferred to Tb3＋ ions, leading to green emission from Tb3＋. Particularly, the corresponding emitting colors of the phosphors could be well-tuned from deep blue（0.16, 0.05） to green region（0.25, 0.45） by adjusting the molar ratio of Ce3＋/Tb3＋.