Mechanistic Studies of Particulate Soil Detergency: I. Hydrophobic Soil Removal

The mechanism of particulate soil detergency using aqueous surfactant systems is not well understood. In this research, carbon black (model hydrophobic soil) removal from a hydrophilic (cotton) and hydrophobic (polyester) fabric is studied using anionic, nonionic, and cationic surfactants. The zeta potential, solid/liquid spreading pressure, contact angle and surfactant adsorption of both soil and fabric are correlated to detergency over a range of surfactant concentrations and pH levels. Electrostatic repulsion between fabric and soil is generally found to be the dominant mechanism responsible for soil removal for all surfactants and fabrics. Steric effects due to surfactant adsorption are also important for nonionic surfactants for soil detachment and antiredeposition. Solid/liquid interfacial tension reduction due to surfactant adsorption also aids in detergency in cationic surfactant systems. Wettability is not seen as being an important factor and SEM photos show that entrapment of soil in the fabric weave is not significant; the particles are only attached to the fabric surface. Anionic surfactants perform best, then nonionic surfactants. Cationic surfactants exhibit poor detergency which is attributed to low surfactant rinseability.     

Enhanced oil recovery from high‐salinity reservoirs by cationic gemini surfactants

In order to enhance oil recovery from high‐salinity reservoirs, a series of cationic gemini surfactants with different hydrophobic tails were synthesized. The surfactants were characterized by elemental analysis, infrared spectroscopy, mass spectrometry, and ¹H‐NMR. According to the requirements of surfactants used in enhanced oil recovery technology, physicochemical properties including surface tension, critical micelle concentration (CMC), contact angle, oil/water interfacial tension, and compatibility with formation water were fully studied. All cationic gemini surfactants have significant impact on the wettability of the oil‐wet surface, and the contact angle decreased remarkably from 98° to 33° after adding the gemini surfactant BA‐14. Under the condition of solution salinity of 65,430 mg/L, the cationic gemini surfactant BA‐14 reduces the interfacial tension to 10^?3 mN/m. Other related tests, including salt tolerance, adsorption, and flooding experiments, have been done. The concentration of 0.1% BA‐14 remains transparent with 120 g/L salinity at 50 °C. The adsorption capacity of BA‐14 is 6.3–11.5 mg/g. The gemini surfactant BA‐14 can improve the oil displacement efficiency by 11.09%. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46086.     

Enhancement in electrical conductive property of polypyrrole‐coated cotton fabrics using cationic surfactant

Recently, great efforts have been made to gain highly conductive fabrics for smart textiles and flexible electromagnetic shielding materials. Different from the conventional chemical synthesis method, fibrillar polypyrrole was synthesized on the cotton fabrics via a simple chemical polymerization process with micelles of cationic surfactant (cetyltrimethylammonium bromide, CTAB) as soft template. The modified cotton fabric exhibited excellent electrical conductivity and electromagnetic interference shielding effectiveness due to the formation of fibrillar polypyrrole on the fiber surface. Electrical conductivity of fabric surface were studied by four‐probe resistivity system. The highly conductive fabric with surface conductivity of 5.8 S cm^?1 could be obtained by changing cationic surfactant concentration. The electromagnetic interference shielding effectiveness (EMI SE) of the modified fabrics was evaluated by the vector network analyzer instrument. Compared with the sample without using surfactant, the EMI SE value of PPy‐coated cotton fabrics increased by 28% after using 0.03 M CTAB as soft template. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43601.     

Role of fluorocarbon surfactant in the preparation of polytetrafluoroethylene‐modified polyacrylate emulsion

Role of fluorocarbon surfactant in the preparation of polytetrafluoroethylene‐modified polyacrylate emulsion is investigated. The fluorocarbon surfactant has an efficient preemulsification to polytetrafluoroethylene (PTFE) powder. It enables PTFE powder to be introduced into the copolymer of n‐butyl acrylate, n‐methyl methacrylate, n‐styrene, and α‐methacrylic acid. Thereby, stable PTFE‐modified polyacrylate emulsion can be formed. The effects of fluorocarbon surfactant on the surface tension, particle size and particle size distribution of the emulsion, as well as the relation between fluorocarbon surfactant and the amount of PTFE powder are fully investigated. The particle size and the surface tension of emulsion strongly depend on the fluorocarbon surfactant concentration in the reaction system. The particle size distribution becomes narrower and the stability of the emulsion is improved with the increasing of the fluorocarbon surfactant concentration. According to the experiments, a possible mechanism of fluorocarbon surfactant in polymerization is proposed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

一种全氟辛基两性磷酸酯氟碳表面活性剂的复配研究

对一种全氟辛基两性磷酸酯氟碳表面活性剂协同作用进行了研究,考察了该表面活性剂与无机盐、阴离子碳氢表面活性剂、阴离子氟碳表面活性剂和非离子氟碳表面活性剂的复配性能,并对结果进行了讨论。研究表明:该两性磷酸酯氟碳表面活性剂自身表面张力为24.0 mN/m;电解质氯化钠对该两性磷酸酯氟碳表面活性剂影响显著,可使表面张力下降到22.4 mN/m;阴离子碳氢表面活性剂十二烷基硫酸钠(SDS)可使表面张力降至21.4 mN/m;阴离子氟碳表面活性剂全氟丁基磺酸钾和四乙基全氟辛基磺酸铵分别使表面张力降至20.9 mN/m和20.2 mN/m;而非离子氟碳表面活性剂N-乙基-N-聚氧乙烯(9)醚-全氟辛基磺酰胺能使表面张力降至20.9 mN/m。     

双尾及多尾氟表面活性剂在有机溶剂中的表面活性研究

拟通过增加油溶性氟表面活性剂分子中碳氟链的数目,从而增大有机溶剂表面吸附层的碳氟链密度,以提高其降低有机溶剂表面张力的能力。合成了2个系列的氟表面活性剂:将全氟辛基磺酰氟与二胺(NH_2(CH_2)nNH_2,n=2,3,6,10)反应,合成以磺酰胺键为连接基、分子中含有2个碳氟链的油溶性氟表面活性剂;通过全氟辛酸与多元醇(乙二醇、1,2-丙二醇、丙三醇和季戊四醇)反应,合成以酯键为连接基、分子中分别含有2,3和4个碳氟链的油溶性氟表面活性剂。研究了这2个系列氟表面活性剂在乙醇、乙酸乙酯、丁酮以及乙醇-乙酸乙酯-丁酮三元混合溶剂中的表面活性,考察了氟表面活性剂分子结构、溶剂种类对表面活性的影响。结果显示,单纯增加碳氟链数目与降低表面张力之间不具有必然的依赖关系,分子整体构型也很重要,同时有机溶剂的种类对氟表面活性剂溶液的表面张力有显著影响。     

Synthesis and Surface Active Properties of Gemini Cationic Surfactants and Interaction with Anionic Azo Dye (AR52)

A homologous series of new gemini cationic surfactants were synthesized and characterized using micro elemental analysis, FTIR, ¹H-NMR and mass spectra. The surface activities of these amphiphiles were determined based on the data of surface tension. Critical micelle concentration, effectiveness of the surface tension reduction, efficiency of adsorption, maximum surface excess, minimum surface area and critical packing parameter were evaluated. The effect of cationic micelles on solubilization of anionic azo dye, sulforhodamine B (Acid Red 52) in aqueous micellar solution of the synthesized gemini cationic surfactants was studied at pH 6.9 ± 0.5 and 25 °C. The results showed that the solubility of dye rose with increasing surfactant concentration as a consequence of some association between the dye and the micelles. It was also observed that the aggregation of surfactant and dye takes place at a surfactant concentration below the CMC of the individual surfactant. The partition coefficients between the bulk water and surfactant micelles as well as the Gibbs energies of distribution of dye between the bulk water and surfactant micelles were calculated using a pseudo-phase model. The effect of the hydrophobic chain length of Gemini cationic surfactants on the distribution parameters was also reported. The results show favorable solubilization of dye in cationic micelles.     

Surface activity and solubilization of a novel series of functional polyurethane surfactants

Functional polyurethane surfactants (di‐block and tri‐block) were synthesized by addition polymerization of 2,4‐toluenediisocyanate with poly(propylene oxide) and monoallyl‐end‐capped poly(ethylene oxide). The chemical structure of the polyurethane surfactants was confirmed by Fourier transform infrared and ¹H NMR spectroscopy. These polymeric surfactants were found to have excellent surface activity. The lowest surface tension of polyurethane surfactant aqueous solutions could be reduced to 37.6 mN m^?1. All the polyurethane surfactants synthesized had low critical micelle concentrations and could reduce the surface tension even at very low concentration levels (10^?6–10^?5 mol L^?1). The solubilization of toluene in micelles of the synthesized polyurethane surfactants was studied using UV‐visible spectroscopy, and the results showed that they all exhibited good solubilization capacity. Possible solubilization positions of toluene in the micelles are conjectured. Copyright © 2006 Society of Chemical Industry     

Synthesis,Characterization, Surface and Biological Activity of Diquaternary Cationic Surfactants Containing Ester Linkage

Two series of diquaternary cationic surfactants designated as E9Nm and E11Nm having two different alkyl chains in their chemical structure were synthesized. The chemical structures of these surfactants were confirmed using elemental analysis, FTIR and ¹H‐NMR spectra. The surface activities of the different surfactants were determined using surface and interfacial tension at 25 °C. The surface parameters including: critical micelle concentration, effectiveness, efficiency, maximum surface excess and minimum surface area were determined. The surface activities of the cationic surfactants were correlated with their chemical structure. The surface activities of the surfactants increased with increasing the hydrophobic chain length. The adsorption and micellization tendencies of the surfactants in solution were determined using the free energies of adsorption and micellization. The synthesized surfactants were evaluated as biocides against bacteria and fungi. Biocidal activity data showed that a gradual increase in the hydrophobic chain length of the surfactant molecules gradually increases the efficiency of these surfactants as biocides.     

Amido-Amine-Based Cationic Gemini Surfactants: Thermal and Interfacial Properties and Interactions with Cationic Polyacrylamide

Experimental studies were conducted to investigate thermal and interfacial properties of two in‐house synthesized amido‐amine‐based cationic gemini surfactants namely: dodecanoic acid [3‐({4‐[(3‐dodecanoylamino‐propyl)‐dimethyl‐amino]‐butyl}‐dimethyl‐amino)‐propyl]‐amide dibromide ( 12‐4‐12 ) and dodecanoic acid [3‐({6‐[(3‐dodecanoylamino‐propyl)‐dimethyl‐amino]‐hexyl}‐dimethyl‐amino)‐propyl]‐amide dibromide ( 12‐6‐12 ). Thermogravimetric analysis showed the excellent thermal stability of surfactants and no structural degradation was observed at temperatures up to 250 °C. The long‐term thermal stability of the surfactants was investigated with the aid of spectroscopic techniques such as nuclear magnetic resonance (NMR (¹H and ¹³C) and Fourier transform infrared (FTIR) spectroscopy. Both surfactants were found to be thermally stable, and no changes in structure were observed after aging for 10 days at 90 °C. The interfacial tension of the surfactants was measured at three different temperatures (30, 60, and 80 °C), and the results showed a decrease in interfacial tension with increasing temperature and increasing spacer length of the surfactants. Rheological measurements were used to assess the interactions between the cationic gemini surfactant and cationic polyacrylamide. The addition of cationic surfactant reduced the viscosity and storage modulus of the polymer at low shear rate and frequency due to surfactant–polymer interactions and charge screening. The investigated surfactant–polymer system has great potential in high‐temperature carbonate reservoirs, where conventional anionic surfactants are not recommended due to high adsorption.     

Synthesis and Evaluation of Novel Amido-Amine Cationic Gemini Surfactants Containing Flexible and Rigid Spacers

New amido‐amine‐based cationic gemini surfactants with flexible and rigid spacers and different hydrophobic tails were synthesized and characterized. These gemini surfactants were prepared by a modified procedure through amidation of long chain carboxylic acids using 3‐(dimethylamino)‐1‐propylamine followed by treatment with halohydrocarbons. The effect of the trans and cis conformation of the spacer double bond was investigated by means of critical micelle concentration, surface tension reduction, and thermal stability. The short‐term thermal stability of the gemini surfactants was assessed using thermogravimetric analysis (TGA) and the long‐term thermal stability was examined by a unique approach based on structure characterization techniques including NMR (¹H and ¹³C) and FTIR analysis. TGA results demonstrated excellent short‐term thermal stability since no structure degradation was observed up to 200 °C. Structural characterization revealed impressive long‐term thermal stability of the gemini surfactants with no structure decomposition after exposing them to 90 °C for 10 days. The critical micelle concentration of gemini surfactants was found to be in the range of 0.77 × 10^?4–3.61 × 10^?4 mol L^?1 and corresponding surface tension (γ_CMC) ranged from 30.34 to 38.12 mN m^?1. The surfactant with the trans conformation of spacer double bond showed better surface properties compared to the surfactant with the cis conformation of spacer double bond. Similarly, increasing surfactant tail length and spacer length resulted in decreasing CMC values. Moreover, bromide counterion showed improved surface properties compared to chloride counterion.     

Ortho ester-based cleavable cationic surfactants

A new type of cleavable cationic surfactant, based on the ortho ester link, is described. Ortho ester amines with alkyl chain lengths from C₈ to C₁₆ were synthesized from a short-chain ortho ester, a fatty alcohol, and an amino acohol. The ortho ester amine was subsequently quaternized with methyl chloride, yielding a cationic surfactant. The structures were confirmed by ¹H and ¹³C nuclear magnetic resonance and the surface chemical properties were investigated by measuring both static and dynamic surface tensions. The results were compared to standard n-alkyl trimethyl ammonium bromides. The critical micelle concentrations were found to vary rather widely, whereas the surface tensions in some cases were comparatively low. The short alkyl chain ortho ester quaternaries were found to have low surface tensions at short surface ages and to induce rapid wetting of a hydrophobic surface in dynamic tests. Additionally, the new surfactants were found to hydrolyze rapidly under mild acidic conditions, as measured by both titation and monitoring of the dynamic surface tension. Further, they showed excellent long-term stability at pH 10 in dilute aqueous solutions. The effect of added electrolyte on rate of hydrolysis was also investigated. A marked enhancement in the hydrolysis rate was found when NaBr was added, whereas NaCl did not have the same effect. The new surfactants could potentially be used to provide temporary surfactant action in application areas such as disinfection, fabric care, personal care, chain lubrication, and mineral flotation as well as in textile processes such as dyeing or scouring.     

Surface Activity and Performance Properties of Gemini Salts of Linear Alkylbenzene Sulfonate in Aqueous Solution

Gemini salts of linear alkylbenzene sulfonate (LABS) were prepared by neutralization of sulfonic acid with a series of low-molecular-weight diamines in aqueous solution. The equilibrium surface activity of Gemini salts of LABS was determined by measuring the surface tension as a function of surfactant concentration to determine the critical micelle concentration (CMC), surface tension at the CMC (γ_CMC), and the area per molecule at the air-water interface (Ų). Electrical conductivity was measured as a function of surfactant concentration to determine the CMC and counterion binding. Dynamic surface tension was measured using a bubble pressure tensiometer to infer the rate at which the surfactant migrates to the air-water interface. Equilibrium interfacial tension against mineral oil was measured using a spinning drop tensiometer. Dynamic interfacial tension was measured using a drop volume tensiometer. The surface tension, CMC, and interfacial tension of Gemini salts of LABS decreased compared to monovalent organic and inorganic salts. The CMC decreases with increasing molecular weight of the diamine spacer group. Dynamic surface and interfacial tension of Gemini salts of LABS are lower than monovalent salts. The foam volume of Gemini salts of LABS was determined using a high shear blender test. The foam volume of Gemini salts of LABS is lower than monovalent salts and depends on the size of the spacer group. Hard-surface cleaning was measured using artificial soil applied to white Formica tiles. Soil removal was determined by optical reflectance as a function of abrasion cycles. Gemini salts of LABS show reduced hard-surface cleaning performance compared to monovalent salts. Detergency of different types of soils on cotton and polyester/cotton fabric was determined by optical reflectance measurements. Gemini salts of LABS show improved cleaning performance compared to monovalent salts. Cleaning performance increases with increasing molecular weight of the diamine spacer group. In situ neutralization of LABS with organic diamines is a simple and efficient way to prepare anionic Gemini surfactants for industrial scale applications.     

Smart anionic polyelectrolytes based on natural polymer for complexation of cationic surfactant

The thermosensitive polyelectrolytes were obtained by grafting 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid (AMPS) onto hydroxypropylcellulose (HPC), a biodegradable polysaccharide. The interactions of the polymers with dodecyltrimethylammonium chloride (DTAC), a model cationic surfactant, were studied. It was found by the measurements of the surface tension and the analysis of fluorescence emission of pyrene used as a fluorescent probe, that the HPC–AMPS graft polymers strongly interact with DTAC with the formation of polymer–surfactant complexes. The critical aggregation concentrations of these polymer–surfactant systems were found to be of the order of 10^?5 mol/dm³. The polymers were found to be potentially useful in the purification of water from cationic surfactants. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2401–2407, 2006     

A quantitative study of factors that influence the substantivity of fragrance chemicals on laundered and dried fabrics

Model investigations of physicochemical aspects of the substantivity of fragrance raw materials on laundered fabrics were performed. The overall process was divided into two consecutive steps, laundry and dryout, which were characterized by affinity and tenacity, respectively. The affinities of fifteen fragrance raw materials to cotton and polyacrylonitrile were measured in standard fabric softener and detergent solutions. Affinities correlated with the corresponding partition coefficient, P(o/w). To study the impact of parameters independent of the chemical structure of the fragrance molecules, 1-[³H]-3-methyl-5-phenylpentanol (phenylhexanol) was selected, and aqueous solutions of defined anionic, nonionic and cationic surfactants were used as model detergent and fabric softener media. A sequence of experiments, based on the fractional factorial design, was planted for quantifying the relative contribution on substantivity of a number of variables: the concentration of the fragrance chemical, the type and concentration of the surfactants, the type and weight of the fabrics (cotton or polyacrylonitrile) and the washing temperature in the case of cotton. The affinity that characterizes the washing process depends mainly on the type of fabric and the type of surfactant and, to a lesser extent, on the surfactant concentration and the temperature. Anionic and nonionic surfactants, the main components of detergent powders, behave similarly, whereas the combination of cationic surfactant with cotton markedly enhances the affinity. For phenylhexanol, the tenacity after dryout is largely controlled by the type of fabric. The role of fiber swelling is discussed. The substantivity, which represents the global effect of laundering and dryout, shows the same trend as the affinity. The complexity of the physicochemical phenomena involved is highlighted by the importance of the interactions between the main contributing factors.     

Synthesis and Characterization of a Novel Short Fluorocarbon Chain Cationic Surfactant

A novel short fluorocarbon chain cationic surfactant has been synthesized to reduce the bioaccumulation of traditional fluorocarbon surfactants and maintain excellent surface properties simultaneously. The structure, surface activity, and micelle formation of surfactants have been investigated by surface tension, conductivity, dynamic light scattering, steady-state fluorescence, Fourier transform infrared spectroscopy, and Nuclear magnetic resonance. The novel surfactant (yield more than 81%) exhibited good surface activity, the critical micelle concentration and surface tension were below 2.35 mmol L⁻¹ and 20.54 mN m⁻¹ in the range of temperature from 288 to 303 K, respectively. The surface tension decreased to 17.45 mN m⁻¹ with an increase in temperature. The thermodynamic parameters (, and ) of micellization for surfactants were evaluated, which implying the micellization process was contributed primarily by the entropy driving. In addition, the aggregation behavior of surfactants was also studied in detail, which demonstrated a small micelle aggregation number of 9.40 and large size distribution of 164–342 nm.     

Synergism and Performance for Systems Containing Binary Mixtures of Anionic/Cationic Surfactants for Enhanced Oil Recovery

The surfactant structure–performance relationship and application properties in enhanced oil recovery (EOR) for binary mixtures of anionic and cationic surfactants are presented and discussed. A polyoxyethylene ether carboxylate anionic surfactant was blended with a quaternary ammonium chloride cationic surfactant and tested for a high-temperature, low-salinity, and high-hardness condition as found in an oil reservoir. These mixtures were tailored by phase behavior tests to form optimal microemulsions with normal octane (n-C8) and crude oil having an API gravity of 48.05°. The ethoxy number of the polyoxyethylene carboxylate anionic surfactant and the chain length of the cationic surfactant were tuned to find an optimal surfactant blend. Interfacial tensions with n-C8 and with crude oil were measured. Synergism between anionic and cationic surfactants was indicated by surface tension measurement, CMC determination, calculation of surface excess concentrations and area per molecule of individual surfactants and their mixtures. Molecular interactions of anionic and cationic surfactants in mixed monolayers and aggregates were calculated by using regular solution theory to find molecular interaction parameters β ^σ and β ^M . Morphologies of surfactant solutions were studied by cryogenic TEM. The use of binary mixtures of anionic/cationic surfactants significantly broadens the scope of application for conventional chemical EOR methods.     

Wettability alteration and reducing water blockage in tight gas sandstone reservoirs using mixed cationic Gemini/nonionic fluorosurfactant mixtures

The unrecovered hydraulic fracturing fluid will invade the matrix and induce water blockage, creating formation damage and hindering the oil or gas production rate. First, the synergistic effect of cationic Gemini surfactant (MQAS) and nonionic fluorosurfactant (N-2821) mixtures on reducing the surface tension and wettability alteration was investigated in this paper. The critical micelle concentration (CMC) of the surfactant mixture is one or two orders of magnitude lower than that of N-2821 and MQAS, indicating that the MQAS/N-2821 mixtures exhibit an apparent synergistic effect in reducing surface tension. Moreover, the maximal contact angle of MQAS/N-2821 mixtures reached 83.55° at α_N-2821 = 0.5, and the total surfactant concentration of 1 × 10⁻⁴ mol/L due to the adsorption of surfactant. The adsorption mechanism of surfactants on the surface of quartz sand was then examined. The adsorption kinetics is consistent with the pseudo-second-order model at different surfactant concentrations, while the Freundlich model is suitable for describing the adsorption behavior of surfactants on the sandstone surface. This finding indicates that surfactant adsorption is multilayered. The MQAS/N-2821 surfactant mixtures have excellent surfactant activity due to the relationship of the capillary pressure to the surface tension, pore radius, and contact angle; thus, the addition of surfactant mixtures can reduce the liquid saturation effectively. Furthermore, the sequential imbibition experiments indicate that MQAS/N-2821 mixtures alter the wettability of the core plug, which results from the adsorption of surfactants. Compared with brine water, the MQAS/N-2821 mixtures decreased the liquid saturation and increased the permeability recovery ratios of the core plug.     

Development of an Environmentally Acceptable Detergent Formulation for Fatty Soils Based on the Lipase from the Indigenous Extremophile Pseudomonas aeruginosa Strain

A lipase derived from an indigenous extremophile Pseudomonas aeruginosa strain isolated from rancid metalworking fluid was evaluated as a detergent additive. Applicability of the obtained enzyme as an additive in detergent formulations was confirmed by its implementation in the formulations of several new products differing in surfactant type and concentrations, demonstrating satisfactory performance in terms of degreasing efficiency and composition of the washing wastewater. The degreasing efficiency of different enzyme‐containing detergent formulations was studied on cotton fabric samples stained with triolein and compared to that of formulations containing only surfactant. The highest efficiency of the fatty soil removal in formulations with a low content of surfactants (0.4 %) was noted in the enzyme formulation containing Lutensol^® XP‐80 (degreasing efficiency >80 %) and Triton^® X‐100 (degreasing efficiency >60 %). An attempt was then made to optimize the composition of the enzyme formulation on the basis of one or both of these surfactants using statistically planned experiments and response surface methodology (RSM). Taking into consideration the environmental aspects and the shown detergency, it appeared that rather high degreasing effects were achieved in formulations based on a low quantities of Lutensol^® XP‐80 (0.4 %) at all pH values. However, pH seemed to have a notable effect since the degreasing efficiency significantly increased with increasing pH and the amount of the enzyme. Formulations having a moderate alkaline pH profile and higher amount of enzyme exhibited a high cleaning performance of fatty soil even at a low concentration of the surfactant.     

Study on aqueous film-forming foam extinguishing agent based on fluorocarbon cationic–hydrocarbon anionic surfactants mixture system

Fluorocarbon surfactants were the main components of aqueous film-forming foam extinguishing agents (AFFF). Unfortunately, the widely used fluorocarbon surfactant perfluorooctane sulfonate (PFOS) was limited due to its toxicity, bioaccumulation and biodegradability. In this paper, an environmentally friendly quaternary ammonium cationic fluorocarbon surfactant with high surface activity and simple synthesis route was reported. The surface performance and aggregation behavior of the mixed solution of this fluorocarbon surfactant and sodium n-octyl sulfate were studied by means of surface tension meter and transmission electron microscope (TEM). The results showed that the synergistic effect of sodium n-octyl sulfate and this fluorocarbon surfactant was significant, and many vesicles could be observed in the mixed solution with the concentration of 0.1 mol/L under TEM. Subsequently, three environmental friendly AFFF formulations (F-1, F-2, F-3) were designed with the mixture of the fluorocarbon surfactant, sodium n-octyl sulfate and lauryl betaine BS-12 as foaming agent. Through its foam performance test, it could be seen that F-3 showed relatively excellent foam performance. The initial foam height h₀ was 70 mm, the 25% drainage time was 315 s, the extinguishing time was 28 s, and the burn-back time was 720 s. This kind of fire extinguishing agent had the potential of fire protection application.