HVOF-Sprayed Adaptive Low Friction NiMoAl–Ag Coating for Tribological Application from 20 to 800 °C

An adaptive NiMoAl–Ag composite coating was deposited by high-velocity oxy fuel spraying, and its tribological properties from 20 to 800 °C under unlubricated conditions were evaluated using a CSM high-temperature tribometer. Scanning electron microscopy, X-ray diffraction and Raman spectroscopy were used to characterize the coating and corresponding wear tracks to determine the lubrication mechanisms. The results showed that the friction coefficient of the NiMoAl–Ag composite coating was around 0.3 from 20 to 600 °C and reached the lowest value of 0.09 at 800 °C. Meanwhile, wear rates of the coating were maintained on the order of 10^?5 mm³/N m at the test temperatures except for 400 and 600 °C. Characterization of the NiMoAl–Ag coating revealed that silver provided lubrication below 400 °C. Ag₂Mo₂O₇ and Ag₂MoO₄, which were formed through tribochemical reactions, acted as high-temperature lubricants above 400 °C. It was especially proposed that silver in a nearly molten state was effective in reducing the friction of the NiMoAl–Ag coating at 800 °C. Moreover, a comprehensive lubrication mechanism model of an NiMoAl–Ag composite coating at 800 °C was established to explain the extremely low friction coefficient and wear rate of the coating.     

Friction and Wear Behaviors of Ag/MoS2/G Composite in Different Atmospheres and at Different Temperatures

Silver-based composite with 15?vol% MoS₂ and with 5?vol% graphite was prepared by powder metallurgy method. The impacts of the counterface materials, atmosphere, and temperature on the tribological behavior of the composite were investigated. It was found that when sliding against brass less effective lubricating film formed, causing a higher friction and wear comparing with ASTM-1045 steel. With the increasing proportion of oxygen in the O₂/N₂ atmosphere, the wear rate and friction coefficient ascended slightly. At 200?°C, the combination lubrication of graphite, MoS₂, and Ag contributed to a low friction coefficient (0.07) and wear rate (6.56?×?10^?6?mm³/Nm). At 400?°C, graphite lost its lubricating role, while silver became excessively soft. Large amount of MoS₂ was oxidized into MoO_3, and the residual MoS₂ formed some island-like lubricating films. Severe adhesive wear occurred on the contact surface, which led to a high friction coefficient (0.25) and a great increase of the wear rate (23.2?×?10^?6?mm³/Nm). At 600?°C, a relatively low friction coefficient (0.1) was obtained because of the formation of high-temperature solid lubricants, (Ag₂Mo₄O₁₃ and Ag₂Mo₂O₇) and liquid Ag₂Mo₂O₇. However, the wear rate at 600?°C was the highest (32.6?×?10^?6?mm³/Nm) due to the thick transfer layer.     

Adaptive Mo2N/MoS2/Ag Tribological Nanocomposite Coatings for Aerospace Applications

Reactively sputtered Mo₂N/MoS₂/Ag nanocomposite coatings were deposited from three individual Mo, MoS₂, and Ag targets in a nitrogen environment onto Si (111), 440C grade stainless steel, and inconel 600 substrates. The power to the Mo target was kept constant, while power to the MoS₂ and Ag targets was varied to obtain different coating compositions. The coatings consisted of Mo₂N, with silver and/or sulfur additions of up to approximately 24 at%. Coating chemistry and crystal structure were evaluated using X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD), which showed the presence of tetragonal Mo₂N and cubic Ag phases. The MoS₂ phase was detected from XPS analysis and was likely present as an amorphous inclusion based on the absence of characteristic XRD peaks. The tribological properties of the coatings were investigated in dry sliding at room temperature against Si₃N₄, 440C stainless steel, and Al₂O₃. Tribological testing was also conducted at 350 and 600 °C against Si₃N₄. The coatings and respective wear tracks were examined using scanning electron microscopy (SEM), optical microscopy, profilometry, energy dispersive X-ray spectroscopy (EDX), and micro-Raman spectroscopy. During room temperature tests, the coefficients of friction (CoF) were relatively high (0.5–1.0) for all coating compositions, and particularly high against Si₃N₄ counterfaces. During high-temperature tests, the CoF of single-phase Mo₂N coatings remained high, but much lower CoFs were observed for composite coatings with both Ag and S additions. CoF values were maintained as low as 0.1 over 10,000 cycles for samples with Ag content in excess of 16 at% and with sulfur content in the 5–14 at% range. The chemistry and phase analysis of coating contact surfaces showed temperature-adaptive behavior with the formation of metallic silver at 350 °C and silver molybdate compounds at 600 °C tests. These adaptive Mo₂N/MoS₂/Ag coatings exhibited wear rates that were two orders of magnitude lower compared to Mo₂N and Mo₂N/Ag coatings, hence providing a high potential for lubrication and wear prevention of high-temperature sliding contacts.     

Effect of Mo and Ag on the friction and wear behavior of ZrO2 (Y2O3)–Ag–CaF2–Mo composites from 20 °C to 1000 °C

In this paper, a series of ZrO₂ matrix high-temperature self-lubricating composites were prepared by hot-press technique. The effect of Mo and Ag on the friction and wear behavior of the ZrO₂(Y₂O₃)–Ag–CaF₂–Mo composites in a wide temperature range was investigated. The XRD results showed that CaMoO₄ formed on the worn surface above 400 °C. The excellent lubrication performance of CaMoO₄ endowed the low coefficient of friction of the ZrO₂(Y₂O₃)–Ag–CaF₂–Mo composites at high temperatures. The ZrO₂(Y₂O₃)–10Ag–10CaF₂–10Mo composites showed favorable wear resistance at all the tested temperatures which was attributed to the combined action of hardness and phase transformation.     

Tribological Properties and Wear Mechanisms of NiCr–Al2O3–SrSO4–Ag Self-Lubricating Composites at Elevated Temperatures

NiCr–Al₂O₃–SrSO₄–Ag self-lubricating composites were prepared by powder metallurgy method and the tribological properties of composites were evaluated by a ball-on-disk tribometer against alumina ball at wide temperature range from the room temperature to 1,000 °C in air. The linear coefficient of thermal expansion was evaluated for investigation of thermal stability of composites. The tribo-chemical reaction films formed on the rubbing surfaces and their effects on the tribological properties of composites at different temperatures were addressed according to the surface characterization by SEM, XRD, and XPS. The results show that the NiCr–Al₂O₃ composite with addition of 10 wt% SrSO₄ and 10 wt% Ag exhibits satisfying friction and wear properties over the entire temperature range from room temperature to 1,000 °C. The composition of the tribo-layers on the worn surfaces of the composites is varied at different temperatures. The synergistic lubricating effect of SrAl₄O₇, Ag, and NiCr₂O₄ lubricating films formed on worn surfaces were identified to reduce the friction coefficient and wear rate from room temperature to 800 °C. Meanwhile, at 1,000 °C, the SrCrO₄ and NiAl₂O₄ was formed on the worn surfaces during sliding process, combining with the NiCr₂O₄, Al₂O₃, Cr₂O₃, Ag, and Ag₂O, which play an important role in the formation of a continuous lubricating film on the sliding surface.     

Tribological properties of Ni3Al matrix composites with addition of silver and barium salt

Ni₃Al matrix composites with addition of silver and barium salt (BaCrO₄, BaMoO₄) were fabricated by powder metallurgy. It was found that from room temperature to 800 °C, Ni₃Al matrix composite with addition of Ag and BaCrO₄ offers the continuous lubrication properties, and its friction coefficient ranges from 0.29 to 0.38; Ni₃Al matrix composite with addition of Ag and BaMoO₄ also offers the favorable lubricating properties; the friction coefficient ranges from 0.28 to 0.35 in a wide temperature range. The low friction coefficient in a wide temperature range could be attributed to the synergistic effect of Ag and barium salts.     

Tribological properties of NiCr–Al2O3 cermet-based composites with addition of multiple-lubricants at elevated temperatures

The tribological properties of NiCr-40 wt% Al₂O₃ (NC40A) cermet-based composites containing SrSO₄ and other lubricant (graphite, MoS₂ and Ag) against alumina ball were evaluated to identify their self-lubrication mechanisms from room temperature to 800 °C. The composites demonstrated distinct improvements in effectively reducing friction and wear, as compared to NC40A cermet. The best results were observed for NC40A–10SrSO₄–10Ag composite, which exhibited satisfactory reproducibility of friction coefficient over a wide temperature range (200–800 °C) through high temperature cyclic friction tests due to the formation of synergistic lubricating films SrAl₄O₇, NiCr₂O₄ and Ag on the contact surface.     

Tribological Properties of Adaptive Ni-Based Composites with Addition of Lubricious Ag2MoO4 at Elevated Temperatures

The Ni-based self-lubricating composites with addition of 10 and 20?wt% Ag₂MoO₄ were fabricated by powder metallurgy technique, and the effect of Ag₂MoO₄ on tribological properties was investigated from room temperature to 700?°C. The tribo-chemical reaction films formed on rubbing surface and their effects on the tribological properties of composites at different temperatures were addressed according to the surface characterization by SEM and Micro-Raman. The results show that the Ag₂MoO₄ decomposed into Ag and Mo during the high-temperature fabrication process. The friction coefficient and wear rate of the composites decrease with the increasing of temperature and Ag₂MoO₄ contents and the composites with addition of 20?wt% Ag₂MoO₄ exhibits the lowest friction coefficient (0.26) and wear rate (1.02?×?10^?5?mm³?N^?1?m^?1) at 700?°C. The composition of the tribo-layers on the worn surfaces of the composites is varied at different temperatures. It is proposed that the improving of tribological properties of the composites at high temperatures are attributed to the synergistic lubricating effect of silver molybdate (reproduced in the rubbing process at high temperatures) and Fe oxide (transfer from disk material to the pin) formed on the worn surface.     

Friction and Wear Behaviors of Ni-based Composites Containing Graphite/Ag2MoO4 Lubricants

In order to improve the tribological properties of Ni-based composites, novel adaptive Ni-based composites containing multiple lubricants were prepared via a mechanical alloying and hot-press sintering technique. The phase constituents and microstructure of the composites were characterized and the tribological properties were evaluated from room temperature to 700 °C. The results showed that the Ag₂MoO₄ phase decomposed and new phases of Mo₂C, Ag, and MoO₃ formed in the sintered composites, which can be attributed to the solid state reaction of silver molybdate lubricant during the sintering process. The wear test results indicated that the Ni-based composites containing graphite and silver molybdate lubricants exhibited superior tribological properties at ambient and high temperatures. Subsequently, the Raman results demonstrated that the composition of the tribo-layers on the worn surface of the Ni-based composites was varied with increasing temperature. Combined with the wear test results, it can be proposed that the improvement of tribological properties is due to the synergistic lubricating action of silver molybdate, iron oxide, and nickel oxide. Furthermore, Raman results of the composite containing silver molybdate and silver/molybdenum trioxide lubricants revealed that the silver molybdate lubricant can reproduce easily by the direct reaction between molybdenum trioxide and silver in the agglomerate state.     

Tribological properties of spark-plasma-sintered ZrO2(Y2O3)-CaF2-Ag composites at elevated temperatures

Spark-plasma sintering is employed to synthesize self-lubricating ZrO₂(Y₂O₃) matrix composites with different additives of CaF₂ and Ag as solid lubricants by tailoring the composition and by adjusting the sintering temperature. The friction and wear behavior of ZrO₂(Y₂O₃) matrix composites have been investigated in dry sliding against an alumina ball from room temperature to 800 °C. The effective self-lubrication at different temperatures depends mainly on the content of various solid lubricants in the composites. The addition of 35 wt.% Ag and 30 wt.% CaF₂ in the ZrO₂(Y₂O₃) matrix can promote the formation of a well-covered lubricating film, and effectively reduce the friction and wear over the entire temperature range studied. The friction coefficients at low temperatures were at a minimum value for the composite containing 35 wt.% of silver. At this silver concentration, low and intermediate temperature lubricating properties are greatly improved without affecting high-temperature lubrication by the calcium fluoride in ZrO₂(Y₂O₃) matrix composites. The worn surfaces and transfer films formed during wear process have been characterized to identify the synergistic lubrication behavior of CaF₂ and Ag lubricants at different temperatures.     

Wear Behavior of (TiB2–TiC)–Ni/TiAl/Ti Gradient Materials Prepared by the FAPAS Process

(TiB₂–TiC)–Ni/TiAl/Ti functionally gradient materials were prepared by field-activated pressure-assisted synthesis processes. (TiB₂–TiC)–Ni composite ceramic, the top layer of the functional gradient materials, was prepared in situ by the combustion synthesis process using Ti and B₄C powders as raw materials. Scanning electron microscope (SEM) images of the ceramic layer revealed that the TiB₂ and TiC particles in the composite were fine and homogeneously dispersed in the Ni matrix. The friction and wear properties of the (TiB₂–TiC)–Ni ceramic were evaluated by sliding against a GCr15 disk at temperatures from ambient up to 400 °C. The experimental results showed that the friction coefficient of the (TiB₂–TiC)–Ni ceramic decreased with the increasing testing temperature, load, and sliding speed. However, the loss rate decreased at higher temperature and increased at higher load and higher sliding speed. The wear mechanisms of (TiB₂–TiC)–Ni ceramic mainly depend upon thermal oxidation at higher temperature, load, and sliding speed. The worn topography and phase component of the worn surfaces were analyzed using SEM, energy dispersive spectroscopy, and X-ray diffraction. The oxide films of Fe₂O₃, TiO₂, and B₂O₃ formed during the friction process play an important role in lubrication, which results in a smaller friction coefficient.     

Effect of the Synergetic Action on Tribological Characteristics of Ni-Based Composites Containing Multiple-Lubricants

Ni-based self-lubricating composites with multiple-lubricants addition were prepared by a powder metallurgy technique, and the effect of multiple-lubricants on tribological properties was investigated from room temperature to 700?°C. The synergetic effects of graphite, MoS₂, and metallic silver lubricants on the tribological characteristics of composites were analyzed. XRD analysis showed that new Cr _x S _y and Mo₂C phase were formed in the composites containing graphite, MoS₂ and metallic Ag lubricants during the sintering process. The average friction coefficients (0.69?C0.22) and wear rates (11.90?C0.09?×?10^?5?mm³?N^?1?m^?1) were obtained when rubbing against Inconel 718 alloy from room temperature to 700?°C due to synergetic lubricating action of multiple-lubricants. A smooth lubricating was gradually generated on the worn surface, and the improving of tribological properties was attributed to the formation of lubricious glaze film on the worn surface and their partially transferred to the counterface. The graphite played the main role of lubrication at room temperature, while molybdate phase and graphite were responsible for low friction coefficients and wear rates at mid/high temperatures. The synergetic lubricating effect of molybdate (produced in the rubbing process at high temperatures) iron oxide (transfer from disk material to the pin) and remaining graphite multiple-lubricants play an important lubricating role during friction tests at a wide temperature range.     

Effects of sintering aids and solid lubricants on tribological behaviours of CMC/Al2O3 pair at 650°C

Ten kinds of self-lubricating composites with different amounts of sintering aids and solid lubricants in Al₂O₃ matrix were fabricated by hot-pressed sintering. Their friction and wear behaviours in unlubricated sliding against Al₂O₃ were tested by using a pin-on-disk wear tester at 650°C. It was shown that the amount of sintering aids strongly affected friction coefficient and wear rate of the Al₂O₃–20Ag20CaF₂ composite, the appropriate amount of sintering aids was 10 wt% for beneficial effect on the reduction of wear at 650°C. Also it was shown that the addition of equal quantities of Ag and CaF₂ in Al₂O₃ matrix can promote the formation of the well-covered lubricating film, and effectively reduce the friction and wear. The composite with 40 wt% of lubricants (20 wt% Ag, 20 wt% CaF₂) presented an optimum tribological behavior at 650°C (friction coefficient μ is about 0.3, wear rates are about 4 x 10^-6 mm³/N,m and 5 x 10^-7 mm³/N,m for the disk and pin, respectively). This revised version was published online in August 2006 with corrections to the Cover Date.     

Effect of Ag and Ti3SiC2 on Tribological Properties of TiAl Matrix Self-lubricating Composites at Room and Increased Temperatures

Dry sliding tribological properties of TiAl matrix self-lubricating composites (TMSC) containing Ag, Ti₃SiC₂, Ag and Ti₃SiC₂ were investigated from 25 to 800 °C under ball-on-disk test conditions against Si₃N₄ counterface under the same conditions of 10 N-0.234 m/s. The results indicated that the tribological properties were strongly dependent on the lubricant additives. TMSC with the addition of Ag and Ti₃SiC₂ (TAT) exhibited the lower friction coefficients (0.32–0.43) and less wear rates (1.23–4.13 × 10^?4 mm³ N^?1m^?1) in the wide temperature range of 25–800 °C. The excellent tribological properties of TAT over the wide temperature range were attributed to the synergetic effect of Ag and Ti₃SiC₂ lubricants, silver diffusion forming a rich-silver smooth tribo-film on the frictional surface of TAT at low and moderate temperatures from 25 to 400 °C, while Ti₃SiC₂ oxidation reaction forming rich-oxide tribo-film on the worn surface of TAT at higher temperatures of 600 and 800 °C.     

Tribological properties of self-lubricating CMC/Al2O3 pairs at high temperature in air

Three different self-lubricating ceramic matrix composites (CMCs) were fabricated by hot-pressed sintering. They are: Al₂O₃-50CaF₂, Al₂O₃-20Ag20CaF₂, and Al₂O₃-10Ag20CaF₂. Tribological tests were performed at temperatures ranging from 20°C to 800°C in air using a pin-on-disk tester. The experimental results show that the addition of the solid lubricants CaF₂ and Ag can evidently reduce the friction coefficients of alumina between 200°C and 650°C but not at room temperature and the wear rate of disks and pins at elevated temperature. The improvements in the friction and wear properties of CMC were due to the formation of a well-covered solid lubricating film. However, breakdown of the lubricating films at 800°C resulted in high friction and wear. This revised version was published online in August 2006 with corrections to the Cover Date.     

Tribological behavior of NiAl matrix composites with addition of oxides at high temperatures

NiAl, NiAl–Cr–Mo alloy and NiAl matrix composites with addition of oxides (ZnO/CuO) were fabricated by powder metallurgy route. It was found that some new phases (such as NiZn₃, Cu_0.81Ni_0.19 and Al₂O₃) are formed during the fabrication process due to a high-temperature solid state reaction. Tribological behavior was studied from room temperature to 1000 °C on an HT-1000 ball-on-disk high temperature tribometer. The results indicated that NiAl had high friction coefficient and wear rate at elevated temperatures, while incorporation of Cr(Mo) not only enhanced mechanical properties evidently but also improved high temperature tribological properties. Among the sintered materials, NiAl matrix composite with addition of ZnO showed the lowest wear rate at 1000 °C, while CuO addition into NiAl matrix composite exhibited the self-lubricating performance and the best tribological properties at 800 °C.     

Tribological properties of Fe7Mo6-based-alloy lubricated with poly-alpha-olefin containing PN additive

Tribological properties of Fe–Mo type disk specimens were investigated against ASTM 52100 steel balls under the lubrication of poly-alpha-olefin (PAO) and PAO containing 1.5 mass% alkyl-phosphonic acid-triazole-methanamine (PN additive). Both the Fe₇Mo₆-based alloy and Mo disk specimens exhibited lower friction and lower wear rates than the Fe and gray cast iron disk specimens under the lubrication of PAO. The friction coefficients of the Fe₇Mo₆-based alloy disk specimens were reduced to 0.07 by adding 1.5 mass% PN additive to PAO. No wear volume loss was observed on the Fe₇Mo₆-based alloy disk specimens when they were lubricated with PAO containing 1.5 mass% PN additive.     

Effect of KMnO4 oxidant additive on solid lubrication of lead-graphite and silver-graphite composites

The purpose of this investigation is to understand the role of KMnO₄ as an oxidant additive on the lubrication properties of a soft metal + graphite composite system, under flat contact sliding conditions where the sliding surfaces interact less with the atmosphere. The sliding tests were made using a ring-on-disk machine, lubricated with Pb or Ag + graphite composite containing different amounts of KMnO₄ additive. The results showed that the addition of KMnO₄ in the composites reduced the friction in air up to temperatures of 500°C. The coefficient of friction was as low as 0.1. This is probably due to the fact that KMnO₄ decomposed during sliding to generate oxygen, which is effective in improving the lubricating ability of graphite. The optimum concentration of KMnO₄ in the solid lubricants (graphite + KMnO₄) was 5–10 vol.%. After decomposition of all oxidant additive in the composite, the coefficient of friction of the composites, however, rose to 0.2–0.3.     

Friction and Wear Characteristics of BaCr2O4 Ceramics at Elevated Temperatures in Sliding Against Sintered Alumina Ball

In this article, friction and wear characteristics of BaCr₂O₄ ceramics have been investigated using a high-temperature friction and wear tester from room temperature to 800?°C in dry sliding against sintered alumina ball. At room temperature, the friction coefficient and wear rate of BaCr₂O₄ ceramics are quite high. BaCr₂O₄ ceramics exhibit low friction coefficients and small wear rates with temperature increasing up to 400?C600?°C. The oxidation reaction of BaCr₂O₄ during high-temperature wear tests is responsible for the tribological properties. The oxidized product of BaCr₂O₄ is BaCrO₄, which forms a smooth self-lubricating film on the worn surface to effectively reduce friction and wear. However, at 800?°C, severe oxidation reduces the relative density of sintered BaCr₂O₄ ceramics, and further expedites the materials removal process.     

Mechanical and tribological properties of sputtered Mo–Se–C coatings

Transition metal dichalcogenides belong to the more developed class of materials for solid lubrication. However, the main limitation of these materials is the detrimental effect of air humidity causing an increase in the friction. In previous works, molybdenum diselenide has been shown to be a promising coating retaining low friction even in very humid environment. In this study, Mo–Se–C films were deposited by sputtering from a C target with pellets of MoSe₂. Besides the evaluation of the chemical composition, the structure, the morphology, the hardness and the cohesion/adhesion, special attention was paid to the tribological characterization.The C content varied from 29 to 68 at.% which led to a progressive increase of the Se/Mo ratio. As a typical trend, the hardness increases with increasing C content. The coatings were tested at room temperature with different air humidity levels and at temperatures up to 500 °C on a pin-on-disc tribometer. The friction coefficient of Mo–Se–C coatings increased with air humidity from ～0.04 to ～0.12, while it was as low as 0.02 at temperature range 100–250 °C. The coatings were very sensitive to the elevated temperature being worn out at 300 °C due to adhesion problems at coating–titanium interface.