Stability characteristics of lifted turbulent partially premixed jet flames

The stability characteristics of partially premixed turbulent lifted methane flames have been investigated and discussed in the present work. Mixture fraction and reaction zone behavior have been measured using a combined 2-D technique of simultaneous Rayleigh scattering, Laser Induced Predissociation Fluorescence (LIPF) of OH and Laser Induced Fluorescence (LIF) of C₂H_x. The stability characteristics and simultaneous mixture fraction-LIPF-LIF measurements in three lifted flames with originally partially premixed jets at different mean equivalence ratio and Reynolds number are presented and discussed in this paper. Higher stability of partially premixed flames as compared to non-premixed flames has been observed. Lifted, attached, blow-out and blow-off regimes have been addressed and discussed in this work. The data show that the mixture fraction field on approaching the stabilization region is uniquely characterized by a certain level of mean and rms fluctuations. This suggests that the stabilization mechanism is likely to be controlled by premixed flame propagation at the stabilization region. Triple flame structure has been detected in the present flames, which is likely to be the appropriate model at the stabilization point.     

Laser optical investigation of turbulent transport of temperature ahead of the preheat zone in a premixed flame

This experimental study investigates temperature profiles upstream of localized thin reaction zones in a turbulent premixed flame stabilized on a low-swirl-burner. A simultaneous dual-sheet Rayleigh/OH-LIPF measurement technique was applied using two parallel laser light sheets to measure the temperature in the preheat zone for three lean (ϕ=0.7) turbulent methane/air flames. The ratio of the turbulence intensity to the laminar burning velocity v′/s_L was varied from 3.5 to 9.2 and to 18.7. The first of these flames lies on the borderline between the “corrugated flamelets” regime and the “thin reaction zones” regime, while the other two are in the “thin reaction zones” regime. The results confirm the occurrence of strong temperature fluctuations ahead of the preheat zone for flames in the “thin reaction zones” regime. Single temperature images show a significant temperature increase ahead of the preheat zones of up to 700 K for flames at the highest turbulence intensity. For statistical analysis conditional mean temperature profiles and probability density functions conditioned on the distance from the flame contour were calculated from the experimental data. Only those portions of the flame front were included which were found to be approximately normal to the two laser sheets. The resulting probability density functions show that the effect of temperature rise ahead of the preheat zone becomes significant only for flames in the “thin reaction zones” regime. The mean temperature profiles show a much smaller temperature rise which, however, increases with increasing velocity ratios v′/s_L.     

Flame speed and tangential strain measurements in widely stratified partially premixed flames interacting with grid turbulence

Methane-air partially premixed flames subjected to grid-generated turbulence are stabilized in a two-slot burner with initial fuel concentration differences leading to stratification across the stoichiometric concentration. The fuel concentration gradient at the location corresponding to the flame base is measured using planar laser induced fluorescence (PLIF) of acetone in the non-reacting mixing field. Simultaneous PLIF of the OH radical and particle image velocimetry (PIV) measurements are performed to deduce the flow velocity and the flame front. These flames exhibit a convex premixed flame front and a trailing diffusion flame, with flow divergence upstream of the flame, as indicated by the instantaneous OH–PLIF, Mie scattering images, and PIV data. The mean streamwise velocity profile attains a global minimum just upstream of the flame front due to expansion of a gases caused by heat release. The flame speed measured just upstream of the flame leading edge is normalized with respect to the turbulent stoichiometric flame speed that takes into account variations in turbulent intensity and integral length scale. The turbulent edge flame speed exceeds the corresponding stoichiometric premixed flame speed and reaches a peak at a certain concentration gradient. The mean tangential strain at the flame leading edge locally peaks at the concentration gradient corresponding to the peak flame speed. The strain varies non-monotonically with the flame curvature unlike in a non-stratified curved premixed flame. The mechanism of peak flame speed is explained as the competition between availability of hot excess reactants from the premixed flame branches to the flame stretch induced due to flame curvature. The results suggest that the stabilization of lifted turbulent partially premixed flames occurs through an edge flame even at a relatively gentle concentration gradient. The strain is also evaluated along the flame front; it peaks at the flame leading edge and decreases gradually on either side of the leading edge. The present results also show qualitatively similar trends as those of laminar triple flames.     

Turbulence and combustion interaction: High resolution local flame front structure visualization using simultaneous single-shot PLIF imaging of CH, OH, and CH2O in a piloted premixed jet flame

High resolution planar laser-induced fluorescence (PLIF) was applied to investigate the local flame front structures of turbulent premixed methane/air jet flames in order to reveal details about turbulence and flame interaction. The targeted turbulent flames were generated on a specially designed coaxial jet burner, in which low speed stoichiometric gas mixture was fed through the outer large tube to provide a laminar pilot flame for stabilization of the high speed jet flame issued through the small inner tube. By varying the inner tube flow speed and keeping the mixture composition as that of the outer tube, different flames were obtained covering both the laminar and turbulent flame regimes with different turbulent intensities. Simultaneous CH/CH₂O, and also OH PLIF images were recorded to characterize the influence of turbulence eddies on the reaction zone structure, with a spatial resolution of about 40 μm and temporal resolution of around 10 ns. Under all experimental conditions, the CH radicals were found to exist only in a thin layer; the CH₂O were found in the inner flame whereas the OH radicals were seen in the outer flame with the thin CH layer separating the OH and CH₂O layers. The outer OH layer is thick and it corresponds to the oxidation zone and post-flame zone; the CH₂O layer is thin in laminar flows; it becomes broad at high speed turbulent flow conditions. This phenomenon was analyzed using chemical kinetic calculations and eddy/flame interaction theory. It appears that under high turbulence intensity conditions, the small eddies in the preheat zone can transport species such as CH₂O from the reaction zones to the preheat zone. The CH₂O species are not consumed in the preheat zone due to the absence of H, O, and OH radicals by which CH₂O is to be oxidized. The CH radicals cannot exist in the preheat zone due to the rapid reactions of this species with O₂ and CO₂ in the inner-layer of the reaction zones. The local PLIF intensities were evaluated using an area integrated PLIF signal. Substantial increase of the CH₂O signal and decrease of CH signal was observed as the jet velocity increases. These observations raise new challenges to the current flamelet type models.     

Large eddy simulation of a lifted turbulent jet flame

The flame index concept for large eddy simulation developed by Domingo et al. [P. Domingo, L. Vervisch, K. Bray, Combust. Theory Modell. 6 (2002) 529–551] is used to capture the partially premixed structure at the leading point and the dual combustion regimes further downstream on a turbulent lifted flame, which is composed of premixed and nonpremixed flame elements each separately described under a flamelet assumption. Predictions for the lifted methane/air jet flame experimentally tested by Mansour [M.S. Mansour, Combust. Flame 133 (2003) 263–274] are made. The simulation covers a wide domain from the jet exit to the far flow field. Good agreement with the data for the lift-off height and the mean mixture fraction has been achieved. The model has also captured the double flames, showing a configuration similar to that of the experiment which involves a rich premixed branch at the jet center and a diffusion branch in the outer region which meet at the so-called triple point at the flame base. This basic structure is contorted by eddies coming from the jet exit but remains stable at the lift-off height. No lean premixed branches are observed in the simulation or and experiment. Further analysis on the stabilization mechanism was conducted. A distinction between the leading point (the most upstream point of the flame) and the stabilization point was made. The later was identified as the position with the maximum premixed heat release. This is in line with the stabilization mechanism proposed by Upatnieks et al. [A. Upatnieks, J. Driscoll, C. Rasmussen, S. Ceccio, Combust. Flame 138 (2004) 259–272].     

A mechanistic study of Soret diffusion in hydrogen–air flames

The separate and combined effects of Soret diffusion of the hydrogen molecule (H₂) and radical (H) on the structure and propagation speed of the freely-propagating planar premixed flames, and the strain-induced extinction response of premixed and nonpremixed counterflow flames, were computationally studied for hydrogen–air mixtures using a detailed reaction mechanism and transport properties. Results show that, except for the conservative freely-propagating planar flame, Soret diffusion of H₂ increases the fuel concentration entering the flame structure and as such modifies the mixture stoichiometry and flame temperature, which could lead to substantial increase (decrease) of the flame speed for the lean (rich) mixtures respectively. On the other hand, Soret diffusion of H actively modifies its concentration and distribution in the reaction zone, which in turn affects the individual reaction rates. In particular, the reaction rates of the symmetric, twin, counterflow premixed flames, especially at near-extinction states, can be increased for lean flames but decreased for rich flames, whose active reaction regions are respectively located at, and away from, the stagnation surface. However, such a difference is eliminated for the single counterflow flame stabilized by an opposing cold nitrogen stream, as the active reaction zone up to the state of extinction is always located away from the stagnation surface. Finally, the reaction rate is increased in general for diffusion flames because the bell-shaped temperature distribution localizes the H concentration to the reaction region which has the maximum temperature.     

Transport budgets in turbulent lifted flames of methane autoigniting in a vitiated co-flow

Autoignition of hydrocarbon fuels is an outstanding research problem of significant practical relevance in engines and gas turbine applications. This paper presents a numerical study of the autoignition of methane, the simplest in the hydrocarbon family. The model burner used here produces a simple, yet representative lifted jet flame issuing in a vitiated surrounding. The calculations employ a composition probability density function (PDF) approach coupled to the commercial CFD package, FLUENT. The in situ adaptive tabulation (ISAT) method is used to implement detailed chemical kinetics. An analysis of species concentrations and transport budgets of convection, turbulent diffusion, and chemical reaction terms is performed with respect to selected species at the base of the lifted turbulent flames. This analysis provides a clearer understanding of the mechanism and the dominant species that control autoignition. Calculations are also performed for test cases that clearly distinguish autoignition from premixed flame propagation, as these are the two most plausible mechanisms for flame stabilization for the turbulent lifted flames under investigation. It is revealed that a radical pool of precursors containing minor species such as CH₃, CH₂O, C₂H₂, C₂H₄, C₂H₆, HO₂, and H₂O₂ builds up prior to autoignition. The transport budgets show a clear convective-reactive balance when autoignition occurs. This is in contrast to the reactive-diffusive balance that occurs in the reaction zone of premixed flames. The buildup of a pool of radical species and the convective-reactive balance of their transport budgets are deemed to be good indicators of the occurrence of autoignition.     

Imaging of diluted turbulent ethylene flames stabilized on a Jet in Hot Coflow (JHC) burner

The spatial distributions of the hydroxyl radical (OH), formaldehyde (H₂CO), and temperature imaged by laser diagnostic techniques are presented using a Jet in Hot Coflow (JHC) burner. The measurements are of turbulent nonpremixed ethylene jet flames, either undiluted or diluted with hydrogen (H₂), air or nitrogen (N₂). The fuel jet issues into a hot and highly diluted coflow at two O₂ levels and a fixed temperature of 1100 K. These conditions emulate those of moderate or intense low oxygen dilution (MILD) combustion. Ethylene is an important species in the oxidation of higher-order hydrocarbon fuels and in the formation of soot. Under the influence of the hot and diluted coflow, soot is seen to be suppressed. At downstream locations, surrounding air is entrained which results in increases in reaction rates and a spatial mismatch between the OH and H₂CO surfaces. In a very low O₂ coflow, a faint outline of the reaction zone is seen to extend to the jet exit plane, whereas at a higher coflow O₂ level, the flames visually appear lifted. In the flames that appear lifted, a continuous OH surface is identified that extends to the jet exit. At the “lift-off” height a transition from weak to strong OH is observed, analogous to a lifted flame. H₂CO is also seen upstream of the transition point, providing further evidence of the occurrence of preignition reactions in the apparent lifted region of these flames. The unique characteristics of these particular cases has led to the term transitional flame.     

A numerical study on NOx formation in laminar counterflow CH4/air triple flames

Formation of NO_x in counterflow methane/air triple flames at atmospheric pressure was investigated by numerical simulation. Detailed chemistry and complex thermal and transport properties were employed. Results indicate that in a triple flame, the appearance of the diffusion flame branch and the interaction between the diffusion flame branch and the premixed flame branches can significantly affect the formation of NO_x, compared to the corresponding premixed flames. A triple flame produces more NO and NO₂ than the corresponding premixed flames due to the appearance of the diffusion flame branch where NO is mainly produced by the thermal mechanism. The contribution of the N₂O intermediate route to the total NO production in a triple flame is much smaller than those of the thermal and prompt routes. The variation in the equivalence ratio of the lean or rich premixed mixture affects the amount of NO formation in a triple flame. The interaction between the diffusion and the premixed flame branches causes the NO and NO₂ formation in a triple flame to be higher than in the corresponding premixed flames, not only in the diffusion flame branch region but also in the premixed flame branch regions. However, this interaction reduces the N₂O formation in a triple flame to a certain extent. The interaction is caused by the heat transfer and the radical diffusion from the diffusion flame branch to the premixed flame branches. With the decrease in the distance between the diffusion flame branch and the premixed flame branches, the interaction is intensified.     

Radiation intensity imaging measurements of methane and dimethyl ether turbulent nonpremixed and partially premixed jet flames

Quantitative time-dependent images of the infrared radiation intensity from methane and dimethyl ether (DME) turbulent nonpremixed and partially premixed jet flames are measured and discussed in this work. The fuel compositions (CH₄/H₂/N₂, C₂H₆O/H₂/N₂, CH₄/air, and C₂H₆O/air) and Reynolds numbers (15,200–46,250) for the flames were selected following the guidelines of the International Workshop on Measurement and Computation of Turbulent Nonpremixed Flames (TNF Workshop). The images of the radiation intensity are acquired using a calibrated high speed infrared camera and three band-pass filters. The band-pass filters enable measurements of radiation from water vapor and carbon dioxide over the entire flame length and beyond. The images reveal localized regions of high and low intensity characteristic of turbulent flames. The peak mean radiation intensity is approximately 15% larger for the DME nonpremixed flames and 30% larger for the DME partially premixed flames in comparison to the corresponding methane flames. The trends are explained by a combination of higher temperatures and longer stoichiometric flame lengths for the DME flames. The longer flame lengths are attributed to the higher density of the DME fuel mixtures based on existing flame length scaling relationships. The longer flame lengths result in larger volumes of high temperature gas and correspondingly higher path-integrated radiation intensities near and downstream of the stoichiometric flame length. The radiation intensity measurements acquired with the infrared camera agree with existing spectroscopy measurements demonstrating the quantitative nature of the present imaging technique. The images provide new benchmark data of turbulent nonpremixed and partially premixed jet flames. The images can be compared with results of large eddy simulations rendered in the form of quantitative images of the infrared radiation intensity. Such comparisons are expected to support the evaluation of models used in turbulent combustion and radiation simulations.     

Flame stabilization in a lifted non-premixed turbulent hydrogen jet with coaxial air

To understand hydrogen jet liftoff height, the stabilization mechanism of turbulent lifted jet flames under non-premixed conditions was studied. The objectives were to determine flame stability mechanisms, to analyze flame structure, and to characterize the lifted jet at the flame stabilization point. Hydrogen flow velocity varied from 100 to 300 m/s. Coaxial air velocity was regulated from 12 to 20 m/s. Simultaneous velocity field and reaction zone measurements used, PIV/OH PLIF techniques with Nd:YAG lasers and CCD/ICCD cameras. Liftoff height decreased with increased fuel velocity. The flame stabilized in a lower velocity region next to the faster fuel jet due to the mixing effects of the coaxial air flow. The non-premixed turbulent lifted hydrogen jet flames had two types of flame structure for both thin and thick flame base. Lifted flame stabilization was related to local principal strain rate and turbulent intensity, assuming that combustion occurs where local flow velocity and turbulent flame propagation velocity are balanced.     

Stable negative edge flame formation in a counterflow burner

In nonpremixed combustion, edge flames can form as a region of flame propagation or flame recession. Forwardly propagating edge flames, as occur in lifted flames, have a local gas velocity at the flame edge that is from unburned partially premixed fuel and air into the flame. These flames represent an ignition process, and permit the flame itself to either stabilize against an incoming gas stream or propagate into unburned fuel and air. Negative edge flames represent the opposite case of a local gas velocity from burned products through the flame edge. The negative edge flame represents a local extinction process, and occurs, for example, during vortex-induced extinction of a nonpremixed flame sheet. A technique for generating steady negative edge flames in a standard counterflow burner is presented, which permits detailed examination of their properties. A coannular counterflow burner is used to create a strain gradient that quenches a central diffusion flame. Unlike previous research on strain-induced flame edges, the axisymmetric flow field ensures gas flow from products through the edge. Measurements of the edge flame's sensitivity to global strain rates and fuel mixtures are presented, along with measurements of the edge flame structure using OH fluorescence and CH emission imaging.     

Autoignited laminar lifted flames of methane, ethylene, ethane, and n-butane jets in coflow air with elevated temperature

The autoignition characteristics of laminar lifted flames of methane, ethylene, ethane, and n-butane fuels have been investigated experimentally in coflow air with elevated temperature over 800 K. The lifted flames were categorized into three regimes depending on the initial temperature and fuel mole fraction: (1) non-autoignited lifted flame, (2) autoignited lifted flame with tribrachial (or triple) edge, and (3) autoignited lifted flame with mild combustion.For the non-autoignited lifted flames at relatively low temperature, the existence of lifted flame depended on the Schmidt number of fuel, such that only the fuels with Sc > 1 exhibited stationary lifted flames. The balance mechanism between the propagation speed of tribrachial flame and local flow velocity stabilized the lifted flames. At relatively high initial temperatures, either autoignited lifted flames having tribrachial edge or autoignited lifted flames with mild combustion existed regardless of the Schmidt number of fuel. The adiabatic ignition delay time played a crucial role for the stabilization of autoignited flames. Especially, heat loss during the ignition process should be accounted for, such that the characteristic convection time, defined by the autoignition height divided by jet velocity was correlated well with the square of the adiabatic ignition delay time for the critical autoignition conditions. The liftoff height was also correlated well with the square of the adiabatic ignition delay time.     

Effect of high hydrogen enrichment on the outer-shear-layer flame of confined lean premixed CH4/H2/air swirl flames

In this study, we investigated the H₂-induced transition of confined swirl flames from the “V” to “M” shape. H₂-enriched lean premixed CH₄/H₂/air flames with H₂ fractions up to 80% were conducted. The flame structure was obtained with Planar Laser-Induced Fluorescence (PLIF) of the OH radical. Flow fields were measured with Particle Image Velocimetry (PIV). It was observed that the flame tip in the outer shear layer gradually propagated upstream and finally anchored to the injector with the hydrogen fractions increase, yielding the transition from the “V” to “M” flame. We examined the flame structures and the flame flow dynamics during the transition. The shape transition was directly related to the evolution of the corner flame along the outer shear layer. With H₂ addition, the outer recirculation zone first appeared downstream where the corner flame started to propagate upstream; then, the recirculation zone expanded upward to form a stable “M” flame gradually. The flow straining was observed to influence the stabilization of the outer shear layer flame significantly. This study can be useful for the understanding of recirculation-stabilized swirling flames with strong confinement. The flame structure and the flow characteristics of flames with a high H₂ content are also valuable for model validation.     

Flame stabilization mechanisms and shape transitions in a 3D printed,hydrogen enriched,methane/air low-swirl burner

Flame shapes and their transitions of premixed hydrogen enriched methane flames in a 3D-printed low-swirl burner are studied using simultaneous OH×CH₂O planar laser induced fluorescence and stereoscopic particle image velocimetry. Three different flame shapes are observed, namely bowl-shape, W-shape, and crown-shape. The bowl-shaped flame has its base stabilized through flame-flow velocity balance and its sides stabilized in the inner shear layer. While the bulges of the W-shaped flame rely on a similar stabilization mechanism in the central flow, its outer edges are stabilized by large-scale eddies in the outer shear layer. The crown-shaped flame is also aerodynamically stabilized in the center, but its outer edges are anchored to the burner hardware. At a fixed equivalence ratio, the statistical transitions between flame shapes across test conditions are jointly dominated by hydrogen fraction and bulk velocity. Dynamically, W-to-crown transition is attributed to the upstream propagation and attachment of the flame outer edges.     

NO formation in counterflow partially premixed flames

An experimental and computational study of NO formation in low-strain-rate partially premixed methane counterflow flames is reported. For progressive fuel-side partial premixing the peak NO concentration increased and the NO distribution along the stagnation streamline broadened. New temperature-dependent emissivity data for a SiO₂-coated Pt thermocouple was used to estimate the radiation correction for the thermocouple, thus improving the accuracy of the reported flame temperature. Flame structure computations with GRIMech 3.00 showed good agreement between measured and computed concentration distributions of NO and OH radical. With progressive partial premixing the contribution of the thermal NO pathway to NO formation increases. The emission index of NO (EINO) first increased and then decreased, reaching its peak value for the level of partial premixing that corresponds to location of the nonpremixed reaction zone at the stagnation plane. The observation of a maximum in EINO at a level of partial premixing corresponding to the nonpremixed reaction zone at the stagnation plane seems to be a consistent feature of low (<20 s⁻¹)-strain-rate counterflow flames.