基于双金属MOFs 制备Co3O4/In2O3 复合物及其气敏性能的研究

以硝酸铟(In(NO₃)₃·xH₂O)、对苯二甲酸(H₂BDC)、六水合硝酸钴(Co(NO₃)· 6H₂O) 为原料, 首先采用一锅油浴法合成了含有Co²⁺ 的铟基金属有机框架材料(MOFs) Co²⁺/CPP-3(In) 材料, 然后在450 ℃ 下焙烧制备Co₃O₄/In₂O₃ 复合物气敏材料, 将Co₃O₄/In₂O₃ 复合物的粉体制作成传感器, 并对其气敏性能进行研究。利用扫描电子显微镜和X 射线衍射仪(XRD) 对双金属MOFs Co²⁺/CPP-3(In) 材料和Co₃O₄/In₂O₃ 复合物进行表征, 采用静态配气法测试其气敏性能。结果表明, Co₃O₄/In₂O₃(n_Co : n_In = 0.4 : 1) 样品的形貌保留了其MOFs 前驱体的棒状结构, 棱柱形框架更为突出, 表面呈凹陷状, 棒体中间粗两边细, 六角截面和棒体均布满了孔洞。结合EDX 和XRD 表征结果, Co²⁺/CPP-3(In) MOFs 前驱体完全转化成Co₃O₄/In₂O₃ 复合物; Co₃O₄/In₂O₃(n_Co : n_In = 0.4 : 1) 复合物在 70 ℃ 下对5×10^-6 H₂S 的气敏性能最优, 响应值达到153, 是同条件下纯备In₂O₃对H₂S 响应值的5 倍, 并且有较好的重复性、选择性和稳定性。     

LiNi0.4Co0.2Mn0.4O2与LiMn2O4共混正极材料电化学性能

为开发具有优良循环性能和安全性能的大型锂离子电池的正极材料,将不同比例的LiNi_(0.4)Co_(0.2)Mn_(0.4)O_2和Li Mn2O4材料进行共混,研究了LiNi_(0.4)Co_(0.2)Mn_(0.4)O_2和Li Mn2O4共混以及共混比例(10∶0、8∶2、7∶3、6∶4、5∶5、0∶10)对锂离子电池的首次放电性能、循环性能和倍率性能以及交流阻抗和循环伏安曲线的影响,并采用扫描电镜对电极材料进行了表征.研究结果表明,共混比例会影响材料的电化学性能,8∶2,7∶3和6∶4配比的混合材料的体积比容量、循环性能和倍率性能要好于纯LiNi_(0.4)Co_(0.2)Mn_(0.4)O_2和Li Mn2O4材料.其中,8∶2配比的材料性能最好.     

Al2O3/(W, Ti)C纳米复合陶瓷材料的力学性能与强韧化机理

采用纳米和亚微米级的α-Al₂O₃,以及微米级的(W,Ti)C粉体为原料,制备了Al₂O₃/(W,Ti)C纳米复合陶瓷材料.在基体Al₂O₃含有体积分数为11%的纳米Al₂O₃时复合材料的抗弯强度和断裂韧性达到最优,其抗弯强度、断裂韧性和硬度分别为840MPa,6.55MPa·m^1/2和20.1GPa.TEM实验表明,纳米颗粒的加入明显抑止了基体晶粒的长大,形成了典型的骨架结构,材料的断裂方式为沿晶断裂和穿晶断裂的混合.内晶型和晶间型第二相颗粒产生的残余应力场、断裂模式的改变和晶粒细化强化促进了复合材料抗弯强度和断裂韧性的提高.     

纳米Al2O3改性环氧胶黏剂和钢铁附着机理的研究

通过拉拔法测定纳米Al₂O₃改性环氧胶黏剂和钢铁之间的附着强度,并结合环氧胶的表面能参数测定以及X射线光电子能谱(XPS)分析,对纳米Al₂O₃提高环氧胶和钢铁附着力的机理进行研究.表面能测定结果表明,添加纳米Al₂O₃使环氧胶的极性增加;XPS能谱分析结果表明,当纳米Al₂O₃质量分数达到2%时,环氧胶中形成新的羧基极性基团;进一步研究发现,当纳米Al₂O₃质量分数为1%时未形成新的羧基基团,当纳米Al₂O₃质量分数为8%时单位接触面积上新的羧基基团的数目较2%时少,这与附着强度的变化规律是一致的.因此,纳米Al₂O₃改性的环氧胶黏剂与钢铁的附着强度的增强是由于Al₂O₃与环氧胶的相互作用形成了新的羧基极性基团．     

TiO2/ML-Ti3C2复合纳米材料的制备及其光催化性能

通过水热技术在二维(2D)多层材料Ti_3C_2 (multi-layer Ti_3C_2, ML-Ti_3C_2)的表面及层间原位晶化和生长锐钛矿相TiO_2纳米球,制备出TiO_2/ML-Ti_3C_2复合纳米材料。采用XRD、SEM、氮吸附等表征技术对TiO_2/ML-Ti_3C_2纳米复合材料进行分析表征,并以亚甲基蓝(MB)为模拟污染物,对纯TiO_2和TiO_2/ML-Ti_3C_2复合纳米材料的光催化性能进行了评价。实验结果表明,两种材料的耦合抑制了Ti O_2中光生电子-空穴对的湮灭,延长了复合光催化剂中载流子寿命,拓宽了复合材料的光谱响应范围。在紫外光照射下,以TiO_2/ML-Ti_3C_2复合纳米材料为光催化剂,200 mg/L的MB溶液在20 min内几乎完全脱色,降解率为98.98%。TiO_2/ML-Ti_3C_2纳米复合材料的光催化性能优于纯TiO_2和Ti_3C_2, Ti_3C_2优异的电子传输能力和超强的吸附性能优化了TiO_2的光催化性能。本研究为使用光催化技术处理废水提供了一种新的思路,具有一定的实际应用前景。     

采用微生物覆铜板浸出液中铁离子制备 Fe2O3/石墨烯纳米复合材料的研究

针对微生物法覆铜板浸出液中的金属铁离子进行资源化处理,提高覆铜板浸出液的附加值。以水热法处理得到的铁离子溶液为原料,制备八面体和球形的Fe_2O_3/石墨烯复合材料,并将其作为锂离子电池负极材料,组装成扣式电池。结果显示:八面体形貌的Fe_2O_3/石墨烯复合材料的比容量高于球形的,其在100 mA/g电流下循环,首次放电和充电比容量分别高达1 343和970 mAh/g,在47次循环后,其放电及充电比容量分别为769和740 mAh/g。     

纳米CuFe2O4活化过一硫酸盐降解诺氟沙星性能

为研究使用过一硫酸盐(PMS)的高级氧化技术去除水体中微量有机污染物的高效可行方法,通过柠檬酸辅助溶胶-凝胶法制备纳米CuFe_2O_4材料,以其为非均相催化剂,探究CuFe_2O_4/PMS体系对诺氟沙星(NFX)的降解性能.采用X射线衍射仪、电子透射显微镜、BET手段对材料进行表征,考察煅烧温度对纳米CuFe_2O_4结构及催化性能的影响,并试验纳米CuFe_2O_4的重复使用性和稳定性.探讨纳米CuFe_2O_4投加量、PMS浓度、溶液初始pH对CuFe_2O_4/PMS体系降解NFX性能的影响,并探究该体系的氧化活性物种及降解机理.结果表明:制备纳米CuFe_2O_4的最佳煅烧温度为400℃,该温度下纳米CuFe_2O_4晶型较好,比表面积较大,且表现出较高的催化活性;在纳米CuFe_2O_4/PMS体系中,控制NFX初始质量浓度为5 mg/L,最适宜的反应条件为:纳米CuFe_2O_4投加量为0.1 g/L、PMS浓度为0.5 mmol/L、初始溶液pH为9.5,该条件下反应30 min后NFX的去除率高达99%;纳米CuFe_2O_4能有效活化PMS生成·OH和SO_4~-·,SO_4~-·是实现NFX快速降解的主要活性物种.     

N掺杂Co3O4纳米片的制备以及活化过一硫酸盐的性能研究

采用牺牲模板法合成N掺杂Co₃O₄纳米片（N-Co NS）,通过透射电子显微镜（TEM）、原子力显微镜（AFM）和光电子能谱（XPS）对制备材料的形貌结构、化学组成进行分析,并通过催化活化过一硫酸盐（PMS）降解水中双酚A （BPA）来探究催化剂的催化性能.实验结果表明与Co₃O₄纳米颗粒（Co NP）、Co₃O₄纳米片（Co NS）相比,N-Co NS表现出了较高的催化性能.在PMS浓度为2 mmol·L^-1、BPA初始质量浓度为50 mg·L^-1的反应条件下,N-Co NS在10 min内完全降解水中的BPA,表明N掺杂和二维纳米片结构有利于催化剂性能的提升.通过pH及离子影响实验证实N-Co NS在复杂水化学环境中仍具有较高的活性.此外结合自由基捕获实验和电子顺磁共振（EPR）测试证实反应体系中产生了高氧化活性的羟基自由基和硫酸根自由基.     

磁性Fe3O4微球的溶剂热法合成及光芬顿性能优化

为探究Fe_3O_4微球的光芬顿性能,在200℃条件下,利用溶剂热法成功制备出具有较好分散性、平均粒径(200±0.5)nm的Fe_3O_4微球,并通过对其原料配比的探究进行样品优化.该合成方法所制备出的Fe_3O_4微球在Photo-Fenton降解亚甲基蓝方面有优秀的性能,降解率达95%甚至以上.此外,Fe_3O_4微球具有易回收的优点,仅利用磁场即可将其分离,且回收率超过85%甚至90%.利用回收后的Fe_3O_4微球探究其重复利用率,结果表明,重复利用过程中样品催化降解效率与第一次使用时几乎相同.本研究探究了该样品降解亚甲基蓝的最佳反应条件,其中当反应体系中加入15 mL过氧化氢且为酸性环境下降解效率达到最大.     

GO/CoFe2O4催化过硫酸盐降解邻苯二甲酸二丁酯效能

为高效地去除水中环境激素类污染物,采用共沉淀法合成了氧化石墨烯负载钴尖晶石铁氧体(GO/CoFe_2O_4)催化剂,催化过硫酸盐(PMS)去除水中邻苯二甲酸二丁酯(DBP).采用SEM、TEM、XPS、XRD对催化剂进行表征,研究不同条件下催化PMS去除水中DBP的效果,提出催化PMS反应机理.结果表明,GO/CoFe_2O_4为颗粒状尖晶石结构,室温下,DBP初始浓度为2μmol/L、催化剂投量为0.1 g/L、PMS浓度为20μmol/L、pH为7时,GO/CoFe_2O_4催化PMS体系对DBP的去除率可达89%,使用5次后催化效果仅降低5%.该新型复合催化剂高效、具有磁性、方便回收,具有良好的工程应用前景.     

Antibiotic properties of Al2O3 doping silver

The preparation technique and properties of Ag-type inorganic antibiotic material carried by Al₂O₃ were studied. The results show that the material has good antibiotic and safety properties, the acute toxicity taken by stomata is LD ₅₀>8 000 mg/kg (little and big white rats), and the normal quantity in subacute toxicity test is 80 mg/(kg · d). The better mass fraction of doping Ag₂O in antibiotic material carried by Al₂O₃ is 4%–8%, and the optimal sintering temperature is from 1 000 °C to 1 100 °C. Foundation item: Project (2002AA327090) supported by National High Technology Research and Development Program of China     

Study of GaN MOS-HEMT using ultrathin Al2O3 dielectric grown by atomic layer deposition

We report on a GaN metal-oxide-semiconductor high electron mobility transistor (MOS-HEMT) using atomic-layer deposited (ALD) Al₂O₃ as the gate dielectric. Through further decreasing the thickness of the gate oxide to 3.5 nm and optimizing the device fabrication process, a device with maximum transconductance of 150 mS/mm was produced. The drain current of this 0.8 μm gate-length MOS-HEMT could reach 800 mA/mm at +3.0 V gate bias. Compared to a conventional AlGaN/GaN HEMT of similar design, better interface property, lower leakage current, and smaller capacitance-voltage (C-V) hysteresis were obtained, and the superiority of this MOS-HEMT device structure with ALD Al₂O₃ gate dielectric was exhibited. Supported by the National Natural Science Foundation of China (Grant No. 60736033) and the National Basic Research Program of China (“973“) (Grant No. 51327020301)     

Pressureless sintered 3Y-TZP/20%Al2O3 composite ceramic

Nanometer 3Y-TZP/20%Al₂O₃ (mass fraction) composite powders prepared by the chemical coprecipitation method were pressureless sintered at 1550 °C for 2 h. Effects of calcining temperatures at 800 °C, 1 000 °C, and 1 200 °C on phase structure, relative density, and Vicker’s hardness of the sintered bodies were studied. The results show that 1 000 °C was the optimal calcining temperature, and the powder calcined was composed of tetragonal zirconia with the Scherrer crystalline size of 6.3nm. The relative density was up to 98.5% under pressureless sintering, and the sintered body was t-ZrO₂ (without m-ZrO₂)+α-Al₂O₃ with the average size of 0.4 μm. Foundation item: State Key Laboratory for Powder Metallurgy(No.9706-36) Biography of the first author: YIN Bang-yao, born in 1966, majoring in advanced ceramic materials.     

Al_2O_3包覆对富锂锰基正极材料Li_(1.2)Mn_(0.54)Co_(0.13)Ni_(0.13)O_2的电化学性能影响

采用水热法合成富锂三元正极材料,探究了最佳包覆比例下Al_2O_3包覆对材料的电化学性能影响.采用扫描电镜(SEM)和X射线衍射仪(XRD)表征了富锂三元正极材料的表面形貌和结构,通过循环伏安(CV)、交流阻抗(EIS)技术分析了材料电化学性的影响因素.结果表明,通过异丙醇铝水解制得了氧化铝包覆层,提高了材料的比容量,稳定了材料的结构.     

碳钢电极在Al_2O_3纳米流体中的腐蚀行为研究

采用电化学阻抗谱和极化曲线研究了碳钢电极在以模拟冷却水为基液的Al_2O_3纳米流体中的腐蚀行为.实验结果表明,Al_2O_3纳米颗粒对碳钢的腐蚀有一定的抑制作用;Al_2O_3纳米流体中碳钢电极的耐蚀性能随着温度的升高而降低,添加分散剂十二烷基苯磺酸钠(SDBS)对碳钢也有一定的缓蚀作用,当SDBS的用量超过一定值时,对碳钢的缓蚀性能开始下降.     

Luminescent properties of BaO-La2O3-B2O3 glasses with dopant

The luminescent properties of glasses synthesized in air atmosphere by conventional high temperature process were stud{ed. The emissions spectra of Eu^2 and Eu^3 were observed in BaO-La2O3-B2O3-Eu2O3 glasses.The results show that the broad emission peaks at 430 nm correspond to 5d→4f emission transition of Eu^2 , the sharp emission peaks at 592, 616, 650 and 250 nm correspond to 5^D0→1Fj(j=1--4) emission transition of Eu^3 ,respectively, which indicates that the BaO-La2O3a-B2O3-Eu2O3 glass can convert ultraviolet and green omponents of sunlight into blue and red light so as to increase the intensity of blue and red light, respectively. The luminescent in--tensity of Eu^2 increases with increasing the molar ratio of Tb^3 in BaO-La2O3-B2O3-Eu2O3a-Tb4O3 glasses, whereas the luminescent intensity of Eua^3 decreases. So the luminescent intensity of Eu(Ⅲ,Ⅱ) is influenced by Tb^3 .These phenomena can be explained by electron transfer mechanism; Eu^3 (4f6) Tb^3 (4f^8)→Eu^2 (4f′) Tb^4 (4f′). Taking advantage of the luminescent properties of BaO-La2O3-B2O3-Eu2O3 glasses, light-conversion glass for agriculture can be produced.     

Effects of temperature and initial molar ratio of Na2O to Al2O3 on agglomeration of fine Al（OH）3 seed in synthetic Bayer solution

Fine Al（OH）3 crystals were aggregated from supersaturated aluminate solution in the batch reaction tanks. By means of laser particle size analyzer and scanning electron microscopy, the influences of temperature and initial molar ratio of Na2O to Al2O3 （aK） on agglomeration of fine seed in Bayer process were investigated. The results show that agglomeration is almost finished in 8 h, and seeds with size less than 2 μm are easily aggregated together, and almost disappear in 8 h under the optimal process conditions. In the aluminate solution with the same moderate initial aK, when the reaction temperature reaches 75 ℃, the secondary nucleation does not occur, and the effect of agglomeration is better. And at the same reaction temperature, when the initial aK is 1.62, the initial supersaturation of aluminate solution is moderate, the binders on the surfaces of the seed are enough to maintain the agglomeration process, and the agglomeration degree is better. From SEM images, agglomeration mainly occurs in the fine particles, the combinations among the fine particles are loose and the new formed coarse crystal shapes are irregular.     

Microstructure and microwave dielectric properties of lead borosilicate glass ceramics with Al2O3

The effects of Al₂O₃ addition on both the sintering behavior and microwave dielectric properties of PbO-B₂O₃-SiO₂ glass ceramics were investigated by Fourier transform infrared spectroscope (FTIR), differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that with the increase of Al₂O₃ content the bands assigned to [SiO₄] nearly disappear. Aluminum replaces silicon in the glass network, which is helpful for the formation of boron-oxygen rings. The increase of the transition temperature T _g and softening temperature T _f of PbO-B₂O₃-SiO₂ glass ceramics leads to the increase of liquid phase precipitation temperature and promotes the structure stability in the glasses, and consequently contributes to the decreasing trend of crystallization. Densification and dielectric constants increase with the increase of Al₂O₃ content, but the dielectric loss is worsened. By contrast, the 3% (mass fraction) Al₂O₃-doped glass ceramics sintered at 725 °C have better properties of density ρ=2.72 g/cm³, dielectric constant ɛ _r =6.78, dielectric loss tan δ=2.6×10⁻³ (measured at 9.8 GHz), which suggest that the glass ceramics can be applied in multilayer microwave devices requiring low sintering temperatures.