Aliphatic polycarbonate‐based polyurethane elastomers and nanocomposites. II. Mechanical,thermal, and gas transport properties

Thermal, thermomechanical, tensile and gas transport properties of aliphatic polycarbonate‐based polyurethanes (PC‐PUs) and their nanocomposites with bentonite for organic systems were studied. Hard segments are formed from hexamethylene diisocyanate and butane‐1,4‐diol. All PC‐PUs and their nanocomposites feature high degree of the phase separation. Three phase transitions were detected by temperature‐modulated differential scanning calorimetry (TMDSC) and dynamic mechanical thermal analysis. TMDSC revealed the filler affinity both to soft and hard segments, even though the affinity to hard segments is much stronger. Elongation‐at‐break at ambient temperatures is mostly over 700%, which leads together with high tensile strength (in some cases) to very high toughness values (over 200 mJ/mm³). The addition of 1 wt % of bentonite does not practically affect mechanical properties implying its very good incorporation into the PU matrix. Permeabilities and other gas transport properties depend on regularity of PC‐diol and on hard segment content, but the variations are insignificant. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of chlorine‐containing flame‐retardant polyurethane nanocomposites via in situ polymerization

We have developed flame‐retardant polyurethanes (FRPUs) and polyurethane (PU) nanocomposites via in situ polymerization. Three series of thermoplastic elastomeric PUs were synthesized to investigate the effect of incorporating 3‐chloro‐1,2‐propanediol (CPD) and nanoclay on mechanical, thermal properties, and also resistance to burning. PU soft segments were based on poly(propylene glycol). Hard segments were based on either CPD or 1,4‐buthane diol (BDO) in combination with methyl phenyl di‐isocyanate named PU or FRPU, respectively. In the third series, CPD was used as chain extender also nanoclay (1% wt) and incorporated and named as flame‐retardant polyurethane nanocomposites (FRPUN). Mechanical properties and LOI of PUs and nanocomposites have been evaluated. Results showed that increasing the hard segment (chlorine content) leads to the increase in flame retardancy and burning time. Addition of nanoclay to CPD‐containing PUs leads to obtain self‐extinguish PUs using lower CPD contents, higher Young's modulus, and strength without any noticeable decrease in elongation at break. Investigation of the TGA results showed that copresence of nanoclay and chlorine structure in the PU backbone can change thermal degradation pattern and improve nanocomposite thermal stability. X‐ray diffraction and transmission electron microscopy studies confirmed that exfoliation and intercalation have been well done. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nonfouling biomaterials based on polyethylene oxide‐containing amphiphilic triblock copolymers as surface modifying additives: Synthesis and characterization of copolymers and surface properties of copolymer–polyurethane blends

The objective of this work is to develop nonfouling biomaterials by blending polyethylene oxide (PEO)‐containing block copolymers with a polyurethane (PU) matrix; it is expected that the PEO component will migrate to the tissue‐material interface. Three amphiphilic triblock copolymers, PEO‐PU‐PEO, in which the PEO MW was 550 (copolymer 1), 2000 (copolymer 2), and 5000 (copolymer 3), respectively, were synthesized. XPS data showed that the polymer/vacuum interfaces of copolymers 2 and 3 were enriched in the PU block, whereas that of copolymer 1 was enriched in the PEO block. In contact with water, the PEO blocks for all three copolymers migrated to the surface as indicated by water contact angles. Blends of the copolymers with a segmented polyurethane were investigated. Surface enrichment of the copolymers occurred and increased over time up to a limit; the degree of enrichment was dependent on PEO block size and copolymer content. At copolymer content <10%, enrichment decreased with increasing PEO block size. For the copolymer 2 and copolymer 3 blends, enrichment increased with increasing copolymer content; at 20% copolymer the surfaces consisted essentially of pure copolymer. For the copolymer 1 blends, the surface was completely covered by copolymer at content ≥ 1%. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and properties of stearate‐intercalated layered double hydroxide nanoplatelet‐reinforced thermoplastic polyurethane

In the past few years, layered double hydroxides (LDHs) with monolayer structure have been much studied for the development of polymer nanocomposites. LDHs with intercalated stearate anions form a bilayer structure with increased interlayer spacing and are expected to be better nanofillers in polymers. In the work reported, thermoplastic polyurethane (PU)/stearate‐intercalated LDH nanocomposites were prepared by solution intercalation and characterized. X‐ray diffraction and transmission electron microscopy confirmed the exfoliation at lower filler loading followed by intercalation at higher filler loading in PU matrix. As regards mechanical properties, these nanocomposites showed maximum improvements in tensile strength (45%) and elongation at break (53%) at 1 and 3 wt% loadings. Maximum improvements in storage and loss moduli (20%) with a shift of glass transition temperature (15 °C) and an increase in thermal stability (32 °C) at 50% weight loss were observed at 8 wt% loading in PU. Differential scanning calorimetry showed a shift of melting temperature of the soft segment in the nanocomposites compared to neat PU, possibly due to the nucleating effect of stearate‐intercalated LDH on the crystal structure of PU. All these findings are promising for the development of mechanically improved, thermally stable novel PU nanocomposites. Copyright © 2011 Society of Chemical Industry     

Synthesis and characterization of polyurethane/Mg‐Al layered double hydroxide nanocomposites

Layered double hydroxide (LDH) is a new type of nanofiller, which improves the physicochemical properties of the polymer matrix. In this study, 1, 3, 5, and 8 wt % of dodecyl sulfate‐intercalated LDH (DS‐LDH) has been used as nanofiller to prepare a series of thermoplastic polyurethane (PU) nanocomposites by solution intercalation method. PU/DS‐LDH composites so formed have been characterized by X‐ray diffraction and transmission electron microscopy analysis which show that the DS‐LDH layers are exfoliated at lower filler (1 and 3 wt %) loading followed by intercalation at higher filler (8 wt %) loading. Mechanical properties of the nanocomposite with 3 wt % of DS‐LDH content shows 67% improvement in tensile strength compared to pristine PU, which has been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscope analysis. Thermogravimetric analysis shows that the thermal stability of the nanocomposite with 3 wt % DS‐LDH content is ≈ 29°C higher than neat PU. Limiting oxygen index of the nanocomposites is also improved from 19 to 23% in neat PU and PU/8 wt% DS‐LDH nanocomposites, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Simultaneous full‐interpenetrating polymer networks of blocked polyurethane and vinyl ester. II. Static and dynamic mechanical properties

Simultaneous full‐interpenetrating polymer networks (full‐IPNs) based on blocked polyurethane (PU) and vinyl ester (VE) have been prepared. The static and dynamic properties of these IPNs have been examined. Results show that the tensile strength and flexural strength of IPNs increased with blocked PU content to a maximum value at 7.5 wt % PU content and then decreased. The tensile modulus, flexural modulus, and hardness of IPNs decreased with increasing blocked PU content. The impact strength of IPNs increased with increasing blocked PU content. The tensile strength, flexural strength, tensile modulus, and flexural modulus of IPNs increased with filler (kaolin) content to a maximum value at 20 to 25 phr filler content and then decreased. The higher the filler content, the greater the hardness, and the lower the impact strength of IPNs. The tensile strength, flexural strength, tensile modulus, flexural modulus, and hardness of IPNs increased with increasing VE initiator content. The dynamic technique was used to determined the damping behavior across a temperature range. Results show that the glass transition temperature (T_g) of IPNs are shifted inwardly compared with pure PU and VE, which indicated that the blocked PU–VE IPNs showed excellent compatible. Meanwhile, the glass transition temperature was shifted to a higher temperature with increased filler content. The dynamic storage modulus (E′) of IPNs increased with increasing VE and filler content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1977–1985, 1999     

Diffusion and sorption of benzene vapor through polybutadiene‐, polybutadiene/styrene‐, and polybutadiene/acrylonitrile‐based polyurethanes

A series of polyurethane (PU) films made from toluene diisocyanate (TDI), 1,4‐butanediol (BDO), and hydroxyl‐terminated polybutadiene (HTPB), hydroxyl terminated polybutadiene/styrene (HTBS), or hydroxyl terminated polybutadiene/acrylonitrile (HTBN) was synthesized by solution polymerization. The absorption of benzene vapor was found mainly in the soft phase. The equilibrium adsorption (M_∞) was reduced with increasing hard segment content for all the PUs. The values of M_∞ were in the sequence of HTBN‐PUs > HTBS‐PUs > HTPB‐PUs, which could be explained by the different interaction parameters between soft segments and benzene. The HTBN‐PU film showed the lowest degree of phase segregation and had more hard segments intermixed in the soft phase, restricting the movement of soft segments, and therefore resulted to non‐Fickian behavior, while the HTPB‐PU is antithetical. FTIR and atomic force microscopy were utilized to identify the hydrogen bonding behavior and morphology change of the PU films before and after the absorption of benzene vapor. The tensile strength of the HTBN‐PUs showed a greater decrease than that of HTBS‐PUs and HTPB‐PUs after absorbing benzene vapor. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2984–2991, 2004     

Comparison of the effects of linking diglycidyl ether‐terminated PDMS and BPA onto polyurethane with respect to the tensile and thermal properties

Flexible poly(dimethylsiloxane) (PDMS) or rigid bisphenol A (BPA) with diglycidyl ether end groups was linked to polyurethane (PU), which was composed of 4,4′‐methylenebis(phenyl isocyanate) as a hard segment and poly(tetramethylene ether)glycol as a soft segment. A control PDMS (CPDMS) series was prepared with an additional deprotonation step by NaH. The spectroscopic, thermal, tensile, shape memory, and low‐temperature flexibility properties were compared with those of plain PU to investigate the effects of linking the flexible PDMS or the rigid BPA on PU. The soft segment melting peaks were not affected by the PDMS content for the PDMS series but disappeared as the BPA content increased in the BPA series. The soft segment crystallization of PU was completely disrupted as the linked BPA content increased in the differential scanning calorimetry results and disappeared in the dynamic mechanical analysis results. The glass transition temperature (T_g) of the BPA series increased with increasing BPA content, whereas that of the PDMS series remained the same. The tensile strength of the PDMS series sharply increased with increasing PDMS content. The shape retention of the BPA series at ?25 °C sharply decreased as the BPA content increased. Finally, the BPA series linked with rigid aromatic BPA demonstrated excellent low‐temperature flexibilities compared with the PDMS series and plain PU. Compared with PUs linked with PDMS, PUs linked with rigid BPA demonstrated a significant change in the cross‐link density, thermal properties, shape retention, and low‐temperature flexibility. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43284.     

Effects of silica nanoparticles on tribology performance of poly(Epoxy Resin‐Bismaleimide)‐based nanocomposites

Introduction of small nanoparticles into polymer matrix increases the mechanical, tribological, and thermal properties of nanocomposites. In this study, poly(epoxy resin‐bismaleimide‐diaminodiphenylmethane) (EP‐BMI‐DDM) copolymers filled with silica nanoparticles (SNPs) were successfully fabricated through in situ suspension polymerization. To enhance the interfacial adhesion of silica particles to the polymer matrix, the nanoparticles were organo‐modified by silane coupling agent. Results of tensile strength test revealed that increased toughness of the composites was attributed to the microcavitations induced by organo‐modified SNPs (OSNPs). Proper loadings of OSNPs can play a critical role in antifriction performance, with optimal friction coefficient of 0.17 (2 wt% OSNPs content). Thermostabilities of the nanocomposites were characterized by differential thermal gravimetric analysis. At the maximum rate of weight loss of EP‐BMI‐DDM/3 wt% OSNP, the temperature measured 452°C, which is 52°C higher than that of pure EP‐BMI‐DDM copolymers (400°C). The produced nanocomposites feature good thermostability and self‐lubrication can be widely used as wearable material under severe working conditions with higher temperature. POLYM. ENG. SCI., 59:274–283, 2019. © 2018 Society of Plastics Engineers     

Preparation and characterization of biodegradable poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate)/silica nanocomposites

Biodegradable poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)]/silica nanocomposites were prepared by melt compounding. The effects of silica on the morphology, crystallization, thermal stability, mechanical properties, and biodegradability of P(3HB‐co‐4HB) were investigated. The nanoparticles showed a fine and homogeneous dispersion in the P(3HB‐co‐4HB) matrix for silica contents below 5 wt%, whereas some aggregates were detected with further increasing silica content. The addition of silica enhanced the crystallization of P(3HB‐co‐4HB) in the nanocomposites due to the heterogeneous nucleation effect of silica. However, the crystal structure of P(3HB‐co‐4HB) was not modified in the presence of silica. The thermal stability of P(3HB‐co‐4HB) was enhanced by the incorporation of silica. Silica was an effective reinforcing agent for P(3HB‐co‐4HB), and the modulus and tensile strength of the nanocomposites increased, whereas the elongation at break decreased with increasing silica loading. The exciting aspect of this work was that the rate of enzymatic degradation of P(3HB‐co‐4HB) was enhanced significantly after nanocomposites preparation. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Synthesis,characterization and properties of organoclay‐modified polyurethane/epoxy interpenetrating polymer network nanocomposites

organoclay‐modified polyurethane/epoxy interpenetrating network nanocomposites (oM‐PU/EP nanocomposites) were prepared by adding organophilic montmorillonite (oMMT) to interpenetrating polymer networks (IPNs) of polyurethane and epoxy resin (PU/EP) which had been prepared by a sequential polymerization technique. Wide‐angle X‐ray diffraction (WAXD) and transmission electronic microscopy (TEM) analysis showed that the interpenetrating process of PU and EP improved the exfoliation and dispersion degree of oMMT. The effects of the NCO/OH ratio (isocyanate index), the weight ratio of PU/EP and oMMT content on the phase structure and the mechanical properties of the oM‐PU/EP nanocomposites were studied by tensile testing and scanning electronic microscopy (SEM). Water absorption tests showed that the PU/EP interpenetrating networks and oMMT had synergistic effects on improvement in the water resistance of the oM‐PU/EP nanocomposites. Differential scanning calorimetry (DSC) analysis showed that PU was compatible with EP and that the glass transition temperature (T_g) of the oM‐PU/EP nanocomposites increased with the oMMT content up to 3 wt%, and then decreased with further increasing oMMT content. The thermal stability of these nanocomposites with various oMMT contents was studied by thermogravimetric analysis (TGA), and the mechanism of thermal stability improvement was discussed according to the experimental results. Copyright © 2005 Society of Chemical Industry     

Crystallization and thermal properties of biodegradable polyurethanes based on poly[(R)‐3‐hydroxybutyrate] and their composites with chitin whiskers

A series of biodegradable polyurethanes (PUs) were synthesized from hydroxylated bacterial poly[(R)‐3‐hydroxybutyrate], P[(R)‐HB]‐diol, as crystallizable hard segment and hydroxyl‐terminated synthetic poly[(R,S)‐3‐hydroxybutyrate), P[(R,S)‐HB]‐diol, as an amorphous soft segment, using 1,6‐hexamethylene diisocyanate, as non‐toxic connecting agent. The P[(R)‐HB] content was varied from 30 to 70 wt %. The resulting copolymers were characterized by FT‐IR, ¹H‐NMR, DSC, and TGA. The DSC data revealed that the melting of P[(R)‐HB] segment increases with increasing its own content in the PUs. The cold and melt crystallization are enhanced with increasing P[(R)‐HB] content. The TGA data revealed that the thermal decomposition mainly occurred via a single degradation step and the thermal stability slightly increased with increasing P[(R)‐HB] content. The non‐isothermal crystallization behavior of PU sample containing 40 wt % PHB with and without α‐Chitin whiskers was studied using DSC, and their kinetics data were investigated via the Avrami, Ozawa, and Z.S. Mo methods, respectively. Crystallization activation energy was estimated using Kissinger's method. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40784.     

Preparation and characterization of biodegradable polyurethanes composites filled with silver nanoparticles-decorated graphene

In this study, polyurethane (PU) was synthesized using 4,4,-diphenylmethane diisocyanate (MDI) as a hard segment, polycaprolactone diol (PCL) as the soft segments and 1,4-butandiol (1,4-BD) as a chain extender. Nanosilver/graphene (Ag/G) was added to the PU matrix to prepare Ag/G/PU nanocomposites. EDS, SEM and XRD are used for assaying the silver content and characterization of Ag/G. TEM, FT-IR, XRD and EDS were used to characterize the structure and morphology of the Ag/G/PUs nanocomposites. The TEM results show that Ag/G belongs to sheet structures and is dispersed in a PU matrix. The SEM showed that the strong interfacial adhesion between the Ag/G and PU is indicated. FT-IR spectra analysis shows that the functional group of PU is free of obvious changes by adding a small amount of Ag/G in the PU matrix. XRD results showed that the main crystalline peak (26°) of Ag/G became more apparent with increasing content of Ag/G, and EDS showed that the content of Ag increased with increasing content of Ag/G in the Ag/G/PUs nanocomposites. The thermal stability and mechanical properties of Ag/G/PUs nanocomposites are improved with increasing content of Ag/G. Contact angle and AFM results showed that the hydrophobicity and surface roughness increased with increasing content of Ag/G. Moreover, the Ag/G/PUs nanocomposites exhibit antibacterial activities toward Staphylococcus aureus as well as Escherichia coli and their antibacterial rates increase with increasing Ag/G. In addition, the electrical conductivity measurements showed that both surface and volume resistance of the Ag/G/PUs nanocomposites decreased as the amount of Ag/G increased.     

Thermal induced shape‐memory and self‐healing of segmented polyurethane containing diselenide bonds

Herein, we synthesized a series of polyurethane copolymers (PUs) with poly(1,4‐butylene adipate) glycol as soft segment and 2,4‐toluene diisocyanate as well as extenders including 1,4‐butanediol and di(1‐hydroxyethylene) diselenide as hard segment. The chemical structure, thermal property, crystallization behavior, shape memory, and self‐healing performances of the PUs were systematically characterized by a series of experiments. It was found that the PU2 containing a higher diselenide component (～33 mol %) exhibited both shape memory and self‐healing behaviors under a moderate temperature (～57 °C). Meanwhile, the PUs showed a good repeatability of shape memory function, and their fixity and recovery ratios were all above 90%. Additionally, the dynamic exchangeable feature of diselenide bonding endues the PUs chains with an acceptable reprocessability and self‐healing performances, and the PU2 sample could be healed for five times by thermal treatment with the healing efficiencies above 70%. This work provides a heuristic perspective for the development of shape memory and self‐healing materials. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46326.     

The effects of soft‐segment molecular weight and organic modifier on properties of organic‐modified MMT‐PU nanocomposites

The effects of soft‐segment molecular weight and organic modification of montmorillonite (MMT) on thermal and mechanical properties of segmented polyurethane (PU) elastomers were investigated. The PU/MMT nanocomposites were prepared by in situ polymerization, and the compositions included soft segments with number average molecular weights of 1000, 2000, and 2900, and organic‐modified MMT (including MMT‐30B and MMT‐I30E). The nanocomposites produced were characterized using wide‐angle X‐ray diffraction (WAXD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and mechanical testing. The TEM and XRD results revealed that both MMT‐30B and MMT‐I30E were intercalated, and partially exfoliated by the PU. Mechanical tests showed that the PU1000 series in soft‐segment molecular weight yielded superior tensile properties compared with the PU2000 and PU2900 series. Also, for a given molecular weight of soft segment in PU, the MMT‐30B nanocomposites exhibited greater increases in Young's modulus, tensile strength, and elongation at break than the MMT‐I30E counterpart, and the crystallinity of PU was enhanced by the clays. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthetic Ni‐talc as filler for producing polyurethane nanocomposites

New synthetic Ni‐talc was used as filler in the synthesis of polyurethane (PU) nanocomposites by in situ polymerization and to emphasize the contribution of the new material compared with natural talc. Good dispersion of Ni‐talc was supported by homogeneous green coloration observed in the polymer matrix. X‐ray diffraction (XRD) analyses indicate the intercalation of polymeric matrix into the filler layers by the increase in d₀₀₁‐spacing value of the Ni‐talc for the nanocomposites when compared to the pristine filler. The nanocomposites obtained with synthetic talc showed an improvement in the crystallization temperature and in thermal stability when compared to pure PU and the composite obtained with natural talc. The young modulus of PU/talc materials containing both Ni‐talc and natural talc were slight higher than pure PU. As shown by scanning electron microscope (SEM), Ni‐talc fillers were well dispersed into the polymeric matrix probably due to the good compatibility of both phases filler/polymer mainly achieved by the filler OH interaction with the urethane group of the polymeric chain. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41854.     

Effect of zeolite particulate filler on the properties of polyurethane composites

Polymer-Zeolites composites have been prepared, using castor oil based polyurethane (PU) as a host and AlPO₄-5 as particulate filler. The prepared PU/zeolite composites have been characterized for mechanical properties such as tensile strength and tensile modulus. These PU composites exhibited an improved mechanical performance compared to the unfilled PU. Thermo gravimetric analyzer (TGA) curve shows that all the chain-extended PUs are stable up to 250 °C and maximum weight loss occurs at 490 °C. The thermal stability of composites increases with increase in zeolite content. Microcrystalline parameters and micro voids of composites have been measured by using wide-angle X-ray scattering (WAXS) and Positron Annihilation Lifetime (PALS) methods respectively. The microcrystalline parameters and micro-voids from PALS indicate the interaction of the filler with the matrix is stronger beyond 5% of the filler which reflect the mechanical performance as well. Surface morphology of composites has been studied using Scanning Electron Microscopy (SEM). The photomicrograph of SEM indicates a uniform distribution of zeolite filler in the PU matrix.     

Thermal and mechanical properties of multiple‐component aliphatic degradable polyurethanes

Macroscopic thermal and mechanical properties of complex aliphatic polycarbonate‐based polyurethane (PU) films containing degradable ester units in PU backbone were studied by a combination of several experimental techniques. Differential scanning calorimetry (DSC) revealed that the synthesized oligomeric diol (DL‐L) contributes (in addition to polycarbonate diol) to the formation of soft‐segment domains, while the hard‐segment domains are formed from 1,6‐diisocyanatohexane (HDI) and butane‐1,4‐diol (BD). Three main phase transitions were detected by DSC and by dynamic mechanical thermal analysis. Thermogravimetric analysis (TGA) of two‐component PUs showed that the PU made from DL‐L and HDI is the least thermostable product, while the PU made from polycarbonate diol and HDI is the most stable one. The differences in the thermal stability of different four‐component PUs are not important. Tensile properties very sensitively reflect the changes in composition and in microstructure of PU samples; the best tensile properties exhibits the degradable sample containing the equimolar ratio of hydroxyl groups of macrodiol, oligomeric diol DL‐L and butane‐1,4‐diol. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41872.     

Thermoplastic polyurethane and nitrile butadiene rubber blends with layered double hydroxide nanocomposites by solution blending

Polymer blending coupled with nanofillers has been widely accepted as one of the cheaper methods to develop high‐performance polymeric materials for various applications. In the present work, dodecyl sulfate intercalated Mg? Al‐based layered double hydroxide (DS‐LDH) was used as nanofiller in the synthesis of polyurethane blended with nitrile butadiene rubber (PU/NBR; 1:1 w/w) nanocomposites, which were subsequently characterized. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed the partial dispersion of Mg? Al layers in PU/NBR blends at lower filler content followed by aggregation at higher filler loading. In comparison to the neat PU/NBR blend, the tensile strength (156%) and elongation at break (21%) show maximum improvement for 1 wt% filler loading. The storage and loss moduli, thermal stability and limiting oxygen index of the nanocomposites are higher compared to the neat PU/NBR blend. Glass transition temperature and swelling measurements increase up to 3 wt% DS‐LDH loading in PU/NBR compared to either neat PU/NBR or its other corresponding nanocomposites. XRD and TEM analyses indicate the partial distribution of DS‐LDH in PU/NBR blends suggesting the formation of partially exfoliated nanocomposites. The improvements in mechanical, thermal and flame retardancy properties are much greater compared to the neat blend confirming the formation of high‐performance polymer nanocomposites. Copyright © 2009 Society of Chemical Industry     

Synthesis and characterization of biodegradable polyurethanes based on L‐cystine/cysteine and poly(ϵ‐caprolactone)

Tunable biodegradable polyurethanes (PUs) with favorable mechanical properties were synthesized from 1,6‐hexamelthylene diisocyanate (HDI) as the hard segment, poly(?‐caprolactone) (PCL) as the soft segment, and L ‐cystine ester as chain extender. The structure of PUs was confirmed by FTIR and ¹H‐NMR. The results of differential scanning calorimeter, thermogravimetric analysis, dynamic mechanical analysis, and tensile test revealed that the thermal and mechanical properties of PUs were strongly influenced by the molecular weight of soft segment PCL. In the presence of glutathione, the disulfide group cleaved into thiols, realizing the PUs degraded and the molecular weight decreased. For PU [550], it remained only 50% of the original M_w. Evaluation of cell viability demonstrated the nontoxicity of the PUs, which facilitated their potential in biomedical applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013