PVA/PEG/TEOS杂化膜制备及性能研究

以聚乙烯醇(PVA)与聚乙二醇(PEG)共混,并与正硅酸乙酯(TEOS)进行交联反应制备杂化膜。FTIR证实杂化溶胶液发生交联反应形成共价键Si—O—C,WXRD观察表明加入TEOS改变了膜结晶度,加入PEG提高了PVA膜对乙醇/水溶液的渗透通量,但分离因子下降,随着TEOS的加入,膜的分离因子提高。在TEOS质量分数为10%时,杂化膜的分离因子达到最大。提高退火温度可以提高膜的分离因子,但通量下降。在100℃下退火12 h的杂化膜对乙醇质量分数为85%的乙醇/水溶液的分离性能最佳。     

PVA/Nano-SiO_2杂化膜的制备及性能研究

以聚乙烯醇(PVA)和正硅酸乙酯(TEOS)为原料,通过溶胶-凝胶(Sol-Gel)技术,制备出不同nano-SiO2含量的PVA/nano-SiO2杂化膜,并采用扫描电子显微镜(SEM)、X射线衍射仪(XRD)等仪器测试和分析了杂化膜的结构和性能。结果表明:随着nano-SiO2含量的增加,PVA杂化膜的耐水性能增强,结晶能力下降,而力学性能呈现先增大后减小的趋势。当nano-SiO2的加入量在10%左右时,断裂伸长率由纯PVA膜的34.74%提高到55.52%,拉伸强度从33.08 MPa增加到49.98 MPa;而当nano-SiO2含量增加到20%以上时,nanoSiO2粒子会发生团聚,使得杂化膜的力学性能变差。     

聚乙烯醇（PVA）／纳米TiO2杂化膜的研究与应用

主要介绍了水溶性聚乙烯醇（PVA）／TiO2杂化膜作为包装材料具有的一些优异性能和用途,从发展现状、制备方法和用途三方面对PVA／TiO2杂化膜进行了归纳总结,并分析了PVA／TiO2杂化膜现阶段所存在的问题。PVA材料的亲水性、环保性、生物相容性及纳米TiO2的亲水性、光照后不发生光腐蚀、耐酸碱性、化学稳定性和对生物无毒性等特点将赋予PVA／TiO2杂化膜广泛的应用前景。     

聚乙烯醇/二氧化硅杂化膜的制备及渗透蒸发分离环己醇（酮）/环己烷

以聚乙烯醇（PVA）和正硅酸乙酯（TEOS）为原料,经溶胶-凝胶（sol-gel）法制备了不同二氧化硅（SiO2）含量的 PVA/SiO2杂化膜。傅里叶变换红外光谱（FT-IR）表明,随着SiO2含量增大,1060cm?1和970cm?1处Si—O—Si特征吸收峰的相对强度逐渐加强,说明TEOS与PVA发生了交联反应;同时膜的分解温度从248℃升高到342℃。杂化膜的SiO2含量从10 %增大到40 %,其玻璃态温度从115℃升高到124℃。以水为溶剂,测定了杂化膜的耐溶剂性能,与PVA膜相比,杂化膜的耐溶剂性能显著提高。以质量比为0.950/0.025/0.025的环己烷/环己醇/环己酮为原料,测定杂化膜的分离性能,结果表明SiO2含量从10 %增大到40 %,通量从15.94 g/(m2?h)升高到75.69 g/(m2?h),环己醇的分离因子从1.8升高到2.65。     

交联聚乙烯醇渗透蒸发膜用于酯化反应过程

研究了交联聚乙烯渗透蒸发膜在酯化反应过程中的应用，以乙酸与正丁醇酯化反应为实验对象，通过渗透蒸发膜选择性地移走产物水，使最终反尖转化率超越平衡转化率，实验考察了温度，进料初始摩尔比，催化剂浓度对过程的影响。     

聚乙烯醇膜的研制及乙醇水溶液的渗透蒸发（PV）分离

选择以聚乙烯醇(PVA)作膜材料,制成具有一定通量及分离效果的聚乙烯醇均质膜及聚乙烯醇/聚砜复合膜。讨论了膜的抗水性及抗化学腐蚀性。用透射电镜及扫描电镜进行了结构测定,并研究了这两种膜在分离95%(重量浓度)乙醇水溶液时的性能以及温度、交联度对膜性能的影响。实验发现聚乙烯醇均质膜具有较高的分离系数;聚乙烯醇/聚砜复合膜在基本维持均质膜分离性能的前提下,通量有较大提高。还发现经Cr~(3 )的饱和溶液处理后再进一步交联的膜,交联度及稳定性都有提高,分离系数略有下降。     

聚乙烯醇-二氧化硅/聚丙烯腈杂化复合膜渗透蒸发分离己内酰胺/水溶液

制备了以聚乙烯醇(PVA)填充纳米SiO2改性膜为活性层,聚丙烯腈(PAN)超滤膜为底膜的PVA-SiO2/PAN杂化复合膜,并用于己内酰胺(CPL)脱水。用FTIR,SEM,XRD,TGA分别对膜进行了表征,并考察了膜中纳米SiO2粒子的质量分数、进料组分质量分数和温度对复合膜分离性能的影响。结果表明,引入纳米SiO2后,杂化膜的热稳定性明显提高。当膜中纳米SiO2质量分数为1.0%时,复合膜渗透蒸发分离性能最佳。60℃下此复合膜用于分离质量分数为40%的CPL溶液时,其总通量和分离因子分别达到2 177 g/(m2.h)和349。     

新型聚乙烯醇/硅系杂化膜的制备及渗透性能

采用溶胶-凝胶法制备了聚乙烯醇（PVA）/γ-氨丙基三乙氧基硅氧烷（APTEOS）有机/无机杂化膜。用FTIR和XRD对杂化膜进行了表征。测定了膜在乙醇/水溶液中的溶胀行为。考察了杂化膜对85%（质量）的乙醇/水溶液的渗透蒸发分离性能。加入APTEOS降低了PVA的结晶度,有效控制了膜的溶胀,呈现出优良的分离性能。随着APTEOS含量的增加,杂化膜的选择性急剧增加,在5.0%（质量）时达到最大值;同时膜的渗透通量迅速增加。解决了PVA膜trade-off效应。     

沸石膜渗透蒸发性能研究进展

渗透蒸发由于其对近沸物和恒沸混合物高效的分离性能而成为当今一个基本的分离操作单元。本文首先对渗透蒸发装置及分离性能表征简要总结,然后重点概述了对沸石膜的渗透蒸发应用和渗透蒸发过程影响因素,最后针对当前研究现状,展望了沸石膜在渗透蒸发方面的发展前景。     

有机-无机杂化纳米复合材料PMMA/TiO2的制备及性能研究

本文对聚甲基丙烯酸甲酯(PMMA)和纳米TiO2复合材料的制备工艺与光学性质进行了研究.利用XRD、SEM、红外光谱、紫外可见光谱、热重等对纳米颗粒及复合材料进行了表征.结果表明:TiO2纳米颗粒经偶联处理后结构没有明显变化,其红外特征峰均发生了红移,PMMA热分解温度随TiO2加入量增大而提高,PMMA/TiO2纳米复合材料在可见光区透过率随TiO2加入量增大而迅速降低.     

Pervaporation characteristics and structure of poly(vinyl alcohol)/poly(ethylene glycol)/tetraethoxysilane hybrid membranes

Poly(vinyl alcohol) (PVA) blended with poly(ethylene glycol) (PEG) was crosslinked with tetraethoxysilane (TEOS) to prepare organic–inorganic PVA/PEG/TEOS hybrid membranes. The membranes were then used for the dehydration of ethanol by pervaporation (PV). The physicochemical structure of the hybrid membranes was studied with Fourier transform infrared spectra (FT‐IR), wide‐angle X‐ray diffraction WXRD, and scanning electron microscopy (SEM). PVA and PEG were crosslinked with TEOS, and the crosslinking density increased with increases in the TEOS content, annealing temperature, and time. The water permselectivity of the hybrid membranes increased with increasing annealing temperature or time; however, the permeation fluxes decreased at the same time. SEM pictures showed that phase separation took place in the hybrid membranes when the TEOS content was greater than 15 wt %. The water permselectivity increased with the addition of TEOS and reached the maximum at 10 wt % TEOS. The water permselectivity decreased, whereas the permeation flux increased, with an increase in the feed water content or feed temperature. The hybrid membrane that was annealed at 130°C for 12 h exhibited high permselectivity with a separation factor of 300 and a permeation flux of 0.046 kg m^?2 h^?1 in PV of 15 wt % water in ethanol. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of hybrid membranes using poly(vinyl alcohol) and tetraethylorthosilicate for the pervaporation separation of water–isopropanol mixtures

Hybrid membranes were prepared using poly(vinyl alcohol) (PVA) and tetraethylorthosilicate (TEOS) via hydrolysis and cocondensation reaction for the pervaporation separation of water‐isopropanol mixtures. The resulting membranes were characterized by Fourier transform infrared spectroscopy, wide‐angle X‐ray diffraction, and differential scanning calorimetry. The glass transition temperature of these membranes varied from 100 to 120°C with increasing TEOS content. Effects of crosslinking density and feed compositions on the pervaporation performances of the membranes were studied. The membrane containing 1.5:1 mass ratio of TEOS to PVA gave the highest separation selectivity of 900 at 30°C for 10 mass % of water in the feed mixture. It was found that the separation selectivity and permeation flux data are strongly dependent on the water composition of the feed and operating temperature. However, the membrane with the highest crosslinking density showed unusual pervaporation properties. The overall activation energy values were calculated using the Arrhenius‐type equation. The activation energy values for the permeation and diffusion varied from 49.18 to 64.96 and 55.13 to 67.31 kJ/mol, respectively. Pervaporation data have also been explained on the basis of thermodynamic quantities. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1304–1315, 2004     

聚乙烯醇/氧化石墨烯分离膜的结构与性能

成膜材料聚乙烯醇（PVA）易溶胀,稳定性差,氧化石墨烯（GO）具有很好的化学稳定性,以PVA为主要原料,GO为添加剂,聚乙二醇为造孔剂,采用共混法制备了GO含量不同的PVA/GO分离膜,并用光学接触角测量仪、超滤杯等考察了分离膜的亲水性和耐污染性;采用SEM、IR、TGA等表征了分离膜的微观形貌、热学及力学性能。结果表明：GO的加入改善了分离膜的内部孔道、亲水性、纯水通量和耐污染能力,膜的热稳定性和力学性能均得到提高,当GO含量为2%时,分离膜的综合性能达到最优。     

Comparative behavior of PVA/PAN and PVA/PES composite pervaporation membranes in the pervaporative dehydration of caprolactam

Flat‐sheet composite membranes were developed by the traditional phase inversion technique using poly;(vinyl alcohol) (PVA). PVA composite pervaporation (PV) membranes were prepared with crosslinked PVA selective layer and porous polyacrylonitrile (PAN) and polyether sulfone (PES) substrate layer material as supports for separating heat sensitivity substance ε‐caprolactam (CPL) from CPL/water mixtures. Glutaraldehyde was used as crosslinking agent. The effect of the composition of glutaraldehyde on membrane stability and structure were investigated. The operating parameters, such as feed concentration and operating temperature, remarkably affected PV performance of the composite membranes. The composite membranes with PVA casted on PAN (PVA/PAN) showed superior PV performance than that casted on PES (PVA/PES). This study has also shown that the type of porous support plays an important role in the PV performance. As a result, this work has presented the information needed of the behavior of PV membranes for dehydration applications of industrial caprolactam. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 4005–4011, 2007     

PVA硫酸酯化聚阴离子材料的制备及表征

利用超声振荡,聚乙烯醇(PVA)与硫酸进行酯化反应制备聚阴离子膜材料。考察了影响反应的因素,确定最佳工艺条件为:3g PVA、20mL水、8g浓硫酸、超声振荡时间80min、反应温度55℃,产品取代度在5%以上,用IR对产品的结构进行了表征。     

丙烯酰胺改性玉米淀粉/PVA复合膜的制备与表征

为了改善聚乙烯醇（PVA）膜的机械性能,选用玉米淀粉为原材料,50℃条件下以过硫酸铵和尿素为引发剂,同时加入丙烯酰胺对淀粉进行接枝改性,制备得到丙烯酰胺改性的玉米淀粉/PVA复合膜。其中,优化改性淀粉的接枝率确定最佳合成条件为淀粉/丙烯酰胺的质量比为3∶7、引发剂过硫酸铵占单体总质量的0.5%、尿素占单体总质量的0.5%。进一步利用优化的改性淀粉为改性剂,制备了系列改性玉米淀粉/PVA复合膜。采用傅里叶红外光谱、扫描电子显微镜（SEM）对复合膜的组成与结构进行表征,同时测定复合膜的机械性能、耐水性、耐热性等物化特性,结果表明30%ST-0.50%APSU改性淀粉的单体转化率为95.0%,接枝率为85.2%。 30%ST-0.50%APSU/PVA复合膜的耐热性能轻微下降,但断裂伸长率提高了256%,耐水性能提高了43.1%。     

PVA/Au纳米复合纤维的制备及表征

以聚乙烯醇(PVA)为还原剂和保护剂,采用PVA还原氯金酸(HAuCl4)制备纳米金(Au),一步法制备PVA/Au溶液,通过静电纺丝制备了PVA/Au纳米复合纤维.利用紫外可见光谱仪、透明电镜和扫描电镜对PVA/Au纳米复合纤维进行了表征.结果表明:随着HAuCl4浓度的增加,Au纳米粒子的粒径逐渐增大;HAuCl4...