Anion exchange membranes of bis-imidazolium cation crosslinked poly(2,6-dimethyl-1,4- phenylene oxide) with enhanced alkaline stability

Partially crosslinked anion exchange membranes (AEMs) with imidazolium-based cationic functionalities were fabricated based on a poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) matrix. The PPO was activated by bromomethylation and functionalized with methylimidazole and 1,4-bis(imidazolyl)butane at different ratios through a gentle and facile heat curing method. The use of 1,4-bis(imidazolyl)butane resulted in a membrane with cationic functionalities incorporated in covalent crosslinks, which allowed for high ion exchange capacities (IECs) without compromising on mechanical robustness. Comprehensive characterizations were performed in terms of thermal stability, water uptake, IEC, swelling, conductivity, mechanical properties and alkaline stability to investigate the correlation of the structure and physicochemical properties. Comparing with the un-crosslinked imidazolium PPO membrane, crosslinked membranes exhibited improved mechanical robustness and alkaline stabilities. The membrane with a crosslinking degree of 10% displayed an IEC of around 1.5 mmol g⁻¹, tensile strength of 4.1 MPa, hydroxide ion conductivity of 40.5 mS cm⁻¹, and a retained ratio in conductivity of 40% after tolerance test of nearly 150 h in 1 mol L⁻¹ KOH (aq.) at 60 °C.     

Macromolecule sulfonated Poly(ether ether ketone) crosslinked poly(4,4′-diphenylether-5,5′-bibenzimidazole) proton exchange membranes: Broaden the temperature application range and enhanced mechanical properties

Proton exchange membranes with a wide application temperature range were fabricated to start high-temperature fuel cells under room temperature. The volume swelling stability, oxidative stability as well as mechanical properties of crosslinked membranes have been improved for covalently crosslinking poly(4,4′-diphenylether-5,5′-bibenzimidazole) (OPBI) with fluorine-terminated sulfonated poly(ether ether ketone) (F-SPEEK) via N-substitution reactions. High proton conductivity was simultaneously realized at both high (80–160 °C) and low (40–80 °C) temperatures by crosslinking and jointly constructing hydrophilic-hydrophobic channels. The crosslinked membranes exhibited the highest proton conductivity of 191 mS cm⁻¹ at 80 °C under 98% relative humidity (RH) and 38 mS cm⁻¹ at 160 °C under anhydrous, respectively. Compared with OPBI membrane, the fuel cell performance of the crosslinked membranes showed higher peak power density at full temperature range (40–160 °C).     

Synthesis and characterization of a long side-chain double-cation crosslinked anion-exchange membrane based on poly(styrene-b-(ethylene-co-butylene)-b-styrene)

By choosing a triple block polymer, poly(styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS), as the backbone and adopting a long side-chain double-cation crosslinking strategy, a series of SEBS-based anion-exchange membranes (AEMs) was successively synthesized by chloromethylation, quaternization, crosslinking, solution casting, and alkalization. The 70C16-SEBS-TMHDA membrane showed high OH⁻ conductivity (72.13 mS/cm at 80 °C) and excellent alkali stability (only 10.86% degradation in OH⁻ conductivity after soaking in 4-M NaOH for 1700 h at 80 °C). Furthermore, the SR was only 9.3% at 80 °C and the peak power density of the H₂/O₂ single cell was up to 189 mW/cm² at a current density of 350 mA/cm² at 80 °C. By introducing long flexible side chains into a polymer SEBS backbone, the structure of the hydrophilic–hydrophobic microphase separation in the membrane was constructed to improve the ionic conductivity. Additionally, network crosslinked structure improved dimensional stability and mechanical properties.     

Cross-linked anion exchange membranes with flexible,long-chain,bis-imidazolium cation cross-linker

Herein, poly (phenylene) oxide (PPO)-based cross-linked anion exchange membranes (AEMs) with flexible, long-chain, bis-imidazolium cation cross-linkers are designed and synthesized. Although the cross-linked membranes possess high ion exchange capacity (IEC) values of up to 3.51–3.94 meq g⁻¹, they have a low swelling degree and good mechanical strength because of their cross-linked structure. Though the membranes with the longest flexible bis-imidazolium cation cross-linker (BMImH-PPO) possess the lowest IEC among these PPO-based AEMs, they show the highest conductivity (24.10 mS cm⁻¹ at 20 °C) and highest power density (325.7 mW cm⁻² at 60 °C) because of the wide hydrophilic/hydrophobic microphase separation in the membranes that promote the construction of ion transport channels, as confirmed by atom force microscope (AFM) images and the small angle X-ray scattering (SAXS) analyses. Furthermore, the BMImH-PPO samples exhibit good chemical stability (10% and 6% decrease in IEC and conductivity, respectively, in 2 M KOH at 80 °C for 480 h, and a 22% decrease in weight in Fenton's reagent at 60 °C for 120 h), making such cross-linked AEMs potentially applicable in alkaline anion exchange membrane fuel cells.     

Novel multi-channel anion exchange membrane based on poly ionic liquid-impregnated cationic metal-organic frameworks

The “trade-off” effect between hydroxide conductivity and dimensional stability is challenging issue for anion exchange membrane fuel cells (AEMFCs). In this study, the framework of UiO-66-NH₂ is for the first time applied to anion exchange membranes (AEMs). The robust pore walls of UiO-66-NH₂ with mechanical and structural durabilities protect the membrane from the excessive swelling effects (a swelling ratio of 7%). In addition, the framework of UiO-66-NH₂ is directly modified into (UiO-66-NH₂)⁺Cl⁻ as hydroxide conduction channels by anion stripping for the first time. And we construct well-organized ion nanochannels by the in-situ self-assembly of N,N,N′,N' -tetramethyl-1,6-hexanediamine (TMHDA) and allyl bromide within the highly ordered pores of (UiO-66-NH₂)⁺Cl⁻. The obtained QA@(UiO-66-NH₂)⁺Cl⁻ then incorporated into pristine membrane (QAPPO) to fabricate the novel multi-channel AEMs. The hydroxide conductivity of QA@(UiO-66-NH₂)⁺Cl⁻/PPO is up to 123 mS⋅cm⁻¹ at 80 °C, which is greatly improved compared to QAPPO pristine membrane.     

Branched poly(ether ether ketone) based anion exchange membrane for H2/O2 fuel cell

High-performance anion exchange membranes (AEMs) are in need for practical application of AEM fuel cells. Novel branched poly(ether ether ketone) (BPEEK) based AEMs were prepared by the copolymerization of phloroglucinol, methylhydroquinone and 4,4′-difluorobenzophenone and following functionalization. The effects of the branched polymer structures and functional groups on the membrane's properties were investigated. The swelling ratios of all the membranes were kept below 15% at room temperature and had good dimensional stability at elevated temperatures. The branching degree has almost no effect on the dimensional change, but plays a great role in tuning the nanophase separation structure. The cyclic ammonium functionalized membrane showed a lower conductivity but a much better stability than imidazolium one. The BPEEK-3-Pip-53 membrane with the branching degree of 3% and piperidine functionalization degree of 53% showed the best performances. The ionic conductivity was 43 mS cm⁻¹ at 60 °C. The ionic conductivity in 1 M KOH at 60 °C after 336 h was 75% of its initial value (25% loss of conductivity), and the IEC was 83% of its initial value (17% loss of IEC), suggesting good alkaline stability. The peak energy density (60 °C) of the single H₂/O₂ fuel cell with BPEEK-3-Pip-53 membrane reached 133 mW cm⁻² at 260 mA cm⁻².     

Study on the partially cross-linked poly(styrene-b-(ethylene-co-butylene)-b-styrene) anion exchange membrane remotely (spaced hexyl) grafted double cation separated by different alkyl groups

In order to improve the alkali stability and OH⁻ conductivity of Poly (styrene-b-(ethylene-co-butylene)-b-styrene) (SEBS)-based anion exchange membranes (AEMs), double cations with different alkyl intervals are remotely grafted onto the SEBS skeleton with hexyl as a linker through reactions such as acylation and ketone reduction. Then, SEBS-0.8Cn-0.2C6 cross-linked membranes were prepared to study the effect of the length of the alkyl chain between the dications on the ion transport and other properties. The OH⁻ conductivity of SEBS-0.8C4-0.2C6 cross-linked membrane can reach 85.27 mS cm⁻¹ at 80 °C, and the peak power density can reach 225 mW cm⁻² at a current density of 450 mA cm⁻². As the dicationic spacer alkyl chains became longer, the swelling rate and water uptake of the membranes increased, resulting in significant improvements in mechanical properties and chemical stability. After soaking in 2 M NaOH solution at 80 °C for 1200 h, the conductivity of SEBS-0.8C6-0.2C6 decreased by only 5.76%. Optimizing the side chain structure of SEBS skeleton can effectively improve the comprehensive performance of AEM.     

Crosslinked poly(arylene ether sulfone) block copolymers containing quinoxaline crosslinkage and pendant butanesulfonic acid groups as proton exchange membranes

Crosslinkable poly (arylene ether sulfone) block copolymers (bSPAES (x/y)) containing pendant butanesulfonic acid and ethanedione groups were prepared from a new side-chain difluoro aromatic monomer 1-(2,6-difluorophenyl)-2-(3,5-dimethoxyphenyl)-1,2-ethanedione via block copolycondensation, demethylation, and further nucleophilic substitution of 1,4-butane sultone. Meanwhile, quinoxaline-based crosslinked block copolymers (C-bSPAES (x/y)) were obtained via cyclocondensation. The corresponding block copolymer membranes have high mechanical properties and anisotropic membrane swelling for either crosslinked or uncrosslinked ones. bSPAES (5/10) with ion exchange capacity (IEC) of 2.05 mequiv. g⁻¹ has low water uptake (WU) of 59.1% at 80 °C but relatively high conductivity of 225 mS cm⁻¹, which is ascribed to its good microphase separation. Meanwhile, the crosslinked C-bSPAES (5/10) with IEC of 1.76 mequiv. g⁻¹ exhibits a decreased WU by half, an improved oxidative stability by 200% and a reduced membrane swelling by 40% than the uncrosslinked bSPAES (5/10). The results suggest that quinoxaline-based crosslinking can obviously improve properties of bSPAES (x/y). In addition, even though maximum power density of C-bSPAES (5/10) is lower than that of Nafion 212, C-bSPAES (5/10) still has an acceptable good single-cell performance, indicating a possible fuel cell application.     

Facile self-crosslinking to improve mechanical and durability of polynorbornene for alkaline anion exchange membranes

Crosslinking is a valid approach to enhance the mechanical and durability performance of anion exchange membranes (AEMs). Herein, a facile and effective self-crosslinking strategy, with no need for an additional crosslinker or a catalyzer, is proposed. A series of tunable self-crosslinking and ion conduction polynorbornene membranes are designed. The 5-norbornene-2-methylene glycidyl ether (NB-MGE) component which affords self-crosslinking enhances dimensional stability, while the flexible 5-norbornene-2-alkoxy-1-hexyl-3-methyl imidazolium chloride (NB-O-Im⁺Cl⁻) hydrophilic unit contributes high conductivity. The crosslinking significantly decreases the water uptake, and water swelling ratio provides excellent solvent-resistance and enhances the thermal and mechanical properties. Additionally, crosslinked rPNB-O-Im-x AEMs exhibit desirable alkaline stability. Impressively, the rPNB-O-Im-30 (IEC = 1.377) shows a moderate ion conductivity (61.8 m S cm⁻¹, 80 °C), with a suppressed water absorption and 88.17% initial OH⁻ conductivity is maintained after treated for 240 h with a 1.0 M NaOH solution at 60 °C. Suitably assessed of rPNB-O-Im-30 AEM reveals a 98.4 mW cm⁻² peak power density reached at a current density of about 208 mA cm⁻². The report offers a facile and effectual preparative technique for preparing dimensional and alkaline stable AEMs for fuel cells applications.     

Quinoxaline-based crosslinked membranes of sulfonated poly(arylene ether sulfone)s for fuel cell applications

A series of crosslinkable sulfonated poly(arylene ether sulfone)s (SPAESs) were synthesized by copolymerization of 4,4′-biphenol with 2,6-difluorobenzil and 3,3′-disulfonated-4,4′-difluorodiphenyl sulfone disodium salt. Quinoxaline-based crosslinked SPAESs were prepared via the cyclocondensation reaction of benzil moieties in polymer chain with 3,3′-diaminobenzidine to form quinoxaline groups acting as covalent and acid-base ionic crosslinking. The uncrosslinked and crosslinked SPAES membranes showed high mechanical properties and the isotropic membrane swelling, while the later became insoluble in tested polar aprotic solvents. The crosslinking significantly improved the membrane performance, i.e., the crosslinked membranes had the lower membrane dimensional change, lower methanol permeability and higher oxidative stability than the corresponding precursor membranes, with keeping the reasonably high proton conductivity. The crosslinked membrane (CS1-2) with measured ion exchange capacity of 1.53 mequiv. g⁻¹ showed a reasonably high proton conductivity of 107 mS/cm with water uptake of 48 wt.% at 80 °C, and exhibited a low methanol permeability of 2.3 × 10⁻⁷ cm² s⁻¹ for 32 wt.% methanol solution at 25 °C. The crosslinked SPAES membranes have potential for PEFC and DMFCs.     

Development of crosslinked SEBS-based anion exchange membranes for water electrolysis: Investigation of the crosslinker effect

SEBS (styrene-b-(ethylene-co-butylene)-b-styrene)) is a non-aryl-ether-type tri-block copolymer widely used as an anion exchange membrane (AEM) material due to its excellent alkaline stability and phase separation properties. However, low tensile strength due to the aliphatic chains and the poor physical properties of the SEBS-based membranes limit their practical application for AEM water electrolysis (AEMWE) or AEM fuel cell (AEMFC). In this study, three types of crosslinked AEMs were prepared using bromohexyl pentafluorobenzyl SEBS as a polymer backbone, and three different crosslinkers, dimethyl amine (DMA), tetramethyl diaminohexane (TMHA), and tris(dimethyl aminomethyl) phenol (TDMAP). Once introduced, these crosslinking agents were converted into the corresponding conducting head groups. The thermal, chemical, physical, and electrical properties of the obtained crosslinked membranes were then investigated for use in AEMWE. In particular, the TDMAP-50x-SEBS membrane with 50% degree of crosslinking experienced hydrogen bonding with water and OH⁻ due to the presence of OH groups in the structure of the crosslinking agent (TDMAP). Because of this, the membrane showed an improved morphology and high conductivity (20 °C: 31.8 mS cm⁻¹, 80 °C: 109.9 mS cm⁻¹). In addition, TDMAP induced physical crosslinking by hydrogen bonding between molecules so that the corresponding membrane (TDMAP-50x-SEBS) exhibited high alkaline and oxidative stability and good mechanical properties. This SEBS-based membrane has a tensile strength of 18.0 MPa and Young's modulus of 165.14 MPa. The WE single-cell test (1 M KOH solution at 70 °C) using TDMAP-50x-SEBS also showed a cell performance of 1190 mA cm⁻² at 2.0 V. This is 126% higher than the cell performance measured for FAA-3-50, a commercialized AEM material, under the same conditions.     

Novel epoxy-based cross-linked polybenzimidazole for high temperature proton exchange membrane fuel cells

An approach has been proposed to prepare the reinforced phosphoric acid (PA) doped cross-linked polybenzimidazole membranes for high temperature proton exchange membrane fuel cells (HT-PEMFCs), using 1,3-bis(2,3-epoxypropoxy)-2,2-dimethylpropane (NGDE) as the cross-linker. FT-IR measurement and solubility test showed the successful completion of the crosslinking reaction. The resulting cross-linked membranes exhibited improved mechanical strength, making it possible to obtain higher phosphoric acid doping levels and therefore relatively high proton conductivity. Moreover, the oxidative stability of the cross-linked membranes was significantly enhanced. For instance, in Fenton’s reagent (3% H₂O₂ solution, 4 ppm Fe²⁺, 70 °C), the cross-linked PBI-NGDE-20% membrane did not break into pieces and kept its shape for more than 480 h and its remaining weight percent was approximately 65%. In addition, the thermal stability was sufficient enough within the operation temperature of PBI-based fuel cells. The cross-linked PBI-NGDE-X% (X is the weight percent of epoxy resin in the cross-linked membranes) membranes displayed relatively high proton conductivity under anhydrous conditions. For instance, PBI-NGDE-5% membrane with acid uptake of 193% exhibited a proton conductivity of 0.017 S cm⁻¹ at 200 °C. All the results indicated that it may be a suitable candidate for applications in HT-PEMFCs.     

Preparation of functional copolymer based composite membranes containing graphene oxide showing improved electrochemical properties and fuel cell performance

The objective of this work is to prepare a functional copolymer of poly(acrylonitrile)-co-poly(2-Acrylamido-2-methyl-1-propanesulfonic acid) (PAN-co-PAMPS) and impregnation of graphene oxide (GO) into the copolymer followed by crosslinking to prepare conetwork composite membranes by simple and cost effective solution casting method and evaluating their structural, morphological, thermal, and mechanical properties. The successful incorporation of different amounts of GO content (0.1–1 wt%) within the polymer matrix was confirmed by FT-IR spectroscopy, X-ray diffraction, transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The mechanical properties of the prepared crosslinked composite membranes are found to be greatly enhanced by the addition of GO in the copolymer matrix. The thermogravimetric analysis (TGA) demonstrated considerable improvements in thermal stability for the composite membrane with low GO content. The effect of loading of GO in the copolymer matrix on proton conductivity and fuel cell performance has been studied systematically. The membranes prepared by mixing with 0.5 wt% GO in the copolymer followed by crosslinking exhibited maximum ionic conductivity (K^m), lower methanol permeability (P_M), and higher relative selectivity. This observed P_M value is much lower range from 3.02 × 10^?7 to 11.9 × 10^?7 cm²/s compared to the Nafion® 117 membrane (22 × 10^?7 cm²/s). The fuel cell performance in terms of maximum power density and current density and the durability of the crosslinked composite membranes have also been evaluated here. Low P_M, high K^m, and high selectivity values show that functional co-polymer/GO crosslinked co-network composite membrane is a promising alternative membrane separator to replace the expensive Nafion® 117 for proton exchange membrane fuel cells (PEMFCs) application.     

The effective methanol-blocking and proton conductivity membranes based on sulfonated poly (ether ether ketone ketone) and polyorganosilicon with functional groups

To solve the conflict between high proton conductivity and low methanol crossover of pristine sulfonated aromatic polymer membranes, the polyorganosilicon doped sulfonated poly (ether ether ketone ketone) (SPEEKK) composite membranes were prepared by introducing polyorganosilicon additive with various functional groups into SPEEKK in this study. Scanning electron microcopy (SEM) images showed the obtained membranes were compact. No apparent agglomerations, cracks and pinholes were observed in the SEM images of composite membranes. The good compatibility between polymer and additive led to the interconnection, thus producing new materials with great characteristics and enhanced performance. Besides, the dual crosslinked structure could be formed in composite membranes through the condensation of silanols and the strong interaction between matrix and additive. The formation of dual crosslinked structure optimized the water absorption, enhanced the hydrolytic stability and oxidative stability of membranes. Especially, the incorporation of additive improved the strength and flexibility of composite membranes at the same time, meaning that the life of the composite membranes might be extended during the fuel cell operation. Meanwhile, the proton conductivity improved with increasing additive content due to the loading of more available acidic groups. It is noteworthy that at 25% additive loading, the proton conductivity reached a maximum value of 5.4 × 10⁻² S cm⁻¹ at 25 °C, which exceeded the corresponding value of Nafion^@ 117 (5.0 × 10⁻² S cm⁻¹) under same experimental conditions. The composite membrane with 20 wt% additive was found to produce the highest selectivity (1.22 × 10⁵ S cm⁻³) with proton conductivity of 4.70 × 10⁻² S cm⁻¹ and methanol diffusion coefficient of 3.85 × 10⁻⁷ cm² s⁻¹, suggesting its best potential as proton exchange membrane for direct methanol fuel cell application. The main novelty of our work is providing a feasible and environment-friendly way to prepare the self-made polyorganosilicon with various functional groups and introducing it into SPEEKK to fabricate the dual crosslinked membranes. This design produces new materials with outstanding performance.     

Macromolecular crosslink of imidazole functionalized poly(vinyl alcohol) and brominated poly(phenylene oxide) for anion exchange membrane with enhanced alkaline stability and ionic conductivity

Anion exchange membranes (AEMs) are important energy conversion device for fuel cell applications, where the overall redox reaction happened. Both alkaline stability and ionic conductivity should be considered in the long-term use of fuel cells. In this work, imidazole functionalized polyvinyl alcohol was designed as the functional macromolecular crosslinking agent to fabricate crosslinked AEMs with brominated poly(phenylene oxide) matrix. Benefitting from the macromolecular crosslinked structure, the membranes displayed enhanced ionic conductivity and alkaline stability at elevated temperature. Moreover, membrane with ion exchange capacity of 1.54 mmol/g displayed ionic conductivity of 78.8 mS/cm at 80 °C, and the conductivity could maintain 75% of the initial value after immersion in 1 M NaOH solution at 80 °C for 1000 h. Moreover, a peak power density of 105 mW/cm² was achieved when the assembled single cell with c-91 was operated at 60 °C. These results indicated that the construction of macromolecular crosslinked AEMs have great potential in the practical application of anion exchange membranes fuel cells.     

Poly (aryl piperidinium) membranes with dipolar alkyl nitrile sidechains for fuel cells

Several poly (biphenyl piperidine-trifluoroacetophenone) based polymers with different grafting ratios of polar alkyl nitrile side chains are synthesized, named PBPAp-PN-x. The relationship between structure and performance is studied, including conductivity, swelling ratio (SR), morphology, single-cell performance, etc. The SR and conductivity at 80 °C of PBPAp-PN30% are 41.0% and 142.3 mS cm⁻¹, whereas those of PBPAp-PN0% are 77.8% and 155.3 mS cm⁻¹, respectively. Further, molecular dynamics (MD) simulations are carried out to microcosmically reveal the mechanism of structure-property relationship, which simulate the number of water molecules (N_H2O) and the diffusion coefficients (D). The simulations also indicate polar cyanide groups can form close contacts, which is similar to physical crosslinking to inhibit the swelling of backbone. As a result, the advantage of grafting dipolar molecules in AEMs not only effectively resolves the “trade-off” problem between ionic conductivity and dimensional stability, but also might be a promising application in fuel cells.     

Novel self-cross-linked multi-imidazolium cations long flexible side chains triblock copolymer anion exchange membrane based on ROMP-type polybenzonorbornadiene

A novel benzonorbornadiene derivative (BenzoNBD-Bis(Im⁺Br⁻-Im⁺I⁻)) grafted by multi-imidazolium cations side-chains combined the rigid alkyl spacer and flexible alkoxy spacer is designed and synthesized. Then, the BenzoNBD-Bis(Im⁺Br⁻-Im⁺I⁻) monomer is copolymerized with the epoxy functionalized norbornene monomer (NB-MGE) and norbornene (NB) via ring-opening metathesis polymerization (ROMP) using Grubbs 3rd catalyst. All as-designed triblock copolymer membranes (TBCMs) show a thermal decomposition temperature beyond 310 °C and can well be dissolved in common organic solvents. The self-cross-linked structure of anion exchange membrane (AEM) is confirmed by gel fraction and tensile measurement. The water uptake and swelling ratio of TBCMs and AEMs are also measured. Major properties required for AEMs such as ion exchange capacity (IEC), hydroxide conductivity and alkaline stability are investigated. AEM-9.09 shows a hydroxide conductivity of 100.74 mS cm⁻¹ at 80 °C. Besides, the micro-phase separated morphology of AEM is confirmed by TEM, AFM and SAXS analyses, AEMs formed distinct micro-phase separation. The as-prepared AEM exhibits a peak power density of 174.5 mW cm⁻² at 365.1 mA cm⁻² tested in a H₂/O₂ single-cell anion exchange membrane fuel cell (AEMFC) at 60 °C. The newly developed strategy of self-cross-linked multi-imidazolium cations long side-chains triblock benzonorbornadiene copolymer provides an effective method to develop high-performance AEMs.     

Guanidinium cationic covalent organic nanosheets-based anion exchange composite membrane for fuel cells

Covalent organic frameworks (COFs) used for anion exchange membrane fuel cells (AEMFCs) are commonly endowed with ion conductivity by post-synthesis modification. However, this method usually results in uneven distribution of functional groups, low functionalization and severe ion capacity fade. Limited by hydrophobic skeleton and relatively large particle size of COFs, the COFs doping amount of the composite membrane is not high. Here we design and synthesize a series of guanidinium cationic covalent organic nanosheets-based anion exchange composite membranes. The positively charged guanidinium group as a building block can induce COF-DhaTG_Cl self-exfoliation into a few layered nanosheets through strong interlayer repulsion. Then, the nanosheets were introduced into quaternary ammonium-functionalized poly(2,6-dimethyl-1,4-phenyl ether) (QPPO). A series of COF-DhaTG_Cl/PPO composite AEMs was prepared with the highest doping amount of 30 wt% by casting method. The porous structure and repeat cationic guanidinium units on the skeleton will expose ion sites to the target ones, providing faster OH⁻ diffusion kinetics in one-dimensional channels. The OH⁻ conductivity of COF-DhaTG_Cl/PPO-20 composite membrane can reach 148.65 mS/cm at 80 °C. Meanwhile, the composite membrane also exhibits enhanced mechanical strength and alkaline stability with the maximum stress strength of 37.3 MPa and the residual conductivity of 96.29% after immersion in 2 M NaOH solution at 60 °C for two weeks.     

Crosslinked sulfonated poly(arylene ether ketone) membranes bearing quinoxaline and acid-base complex cross-linkages for fuel cell applications

A series of crosslinkable sulfonated poly(arylene ether ketone)s (SPAEKs) were synthesized by copolymerization of 4,4′-biphenol with 2,6-difluorobenzil and 5,5′-carbonyl-bis(2-fluorobenzene-sulfonate). A facile crosslinking method was successfully developed, based on the cyclocondensation reaction of benzil moieties in polymer chain with 3,3′-diaminobenzidine to form quinoxaline groups acting as covalent and acid-base ionic crosslinking. The uncrosslinked and crosslinked SPAEK membranes showed high mechanical properties and the isotropic membrane swelling, while the later became insoluble in tested polar aprotic solvents. The crosslinking significantly improved the membrane performance, i.e., the crosslinked membranes had the lower membrane dimensional change, lower methanol permeability and higher oxidative stability than the corresponding precursor membranes, with keeping the reasonably high proton conductivity. The crosslinked membrane (C-B4) with an ion exchange capacity of 2.02 mequiv. g⁻¹ showed a reasonably high proton conductivity of 111 mS cm⁻¹ with a low water uptake of 42 wt% at 80 °C. C-B4 exhibited a low methanol permeability of 0.55 × 10⁻⁶ cm² s⁻¹ for 32 wt% methanol solution at 25 °C. The crosslinked SPAEK membranes have potential for PEFC and DMFC applications.     

Crosslinked polymer electrolytes of high pyridine contents for HT-PEM fuel cells

This report evaluates a new family of pyridine containing aromatic polyether sulfones as polymer electrolytes for high temperature polymer electrolyte membrane fuel cells (HTPEM FCs). The polymers are prepared by high temperature polyetherification reactions, yielding highly soluble polymers even with pyridine contents as high as 90%. Along with the pyridine content, crosslinking density is also tuned, leading to the enhancement of membrane properties such as film integrity, dimensional stability and doping ability in acidic media. The completion of the crosslinking reaction is enabled by a short thermal pre-treatment, preceding the doping step in H₃PO₄ 85%. Both the linear and the crosslinked membranes show high thermal and oxidative stability. Membranes before and after crosslinking are integrated in single cells where their conductivity and performance are monitored, revealing conductivities above 7 × 10⁻² S/cm at temperatures higher than 180 °C.