共查询到20条相似文献,搜索用时 125 毫秒
1.
为了解决谐波电流检测方法中锁相环和滤波器所引起的检测误差和延时问题,对单相电路有功电流分离法进行了深入研究,提出了一种新的谐波电流检测方法。该方法去掉了锁相环,引入了平均值理论,解决了锁相环对检测准确性和低通滤波器对检测实时性的影响,提高了检测的准确性,加快了动态响应速度。理论分析和仿真验证表明,该方法可以准确、实时地检测谐波电流。 相似文献
2.
3.
4.
分布式电源并网系统远程孤岛检测方法的研究 总被引:1,自引:0,他引:1
对孤岛效应快速、有效地检测是分布式发电系统并网运行必须解决的关键问题,现有的孤岛检测可分为本地检测和远程检测。本地检测不能取得令人满意的检测效果,因为被动检测存在大的检测盲区,而主动检测会影响电能质量,且不能用于多个分布式电源的情形。远程检测克服了本地检测的缺点,能够满足检测要求。综述了远程检测方法、尤其是最新的智能远程方法,分析了各种方法的原理和优缺点,随着智能电网的发展,远程检测方法应用于分布式电源并网系统将成为必然趋势。 相似文献
5.
6.
基于瞬时无功功率理论对应用HPF(高通滤波器)检测高次谐波电流和无功电流的方法进行了简要分析,提出了一种改进型的检测方法,进行了理论上的验算,利用MATLAB软件对检测技术进行了仿真研究。仿真结果表明:该方法比常用的LPF(低通滤波器)的谐波检测分离方法具有更好的检测实时性;并注意到了利用HPF谐波电流检测电路无法得到被检测电流的全部谐波电流成分,必须在谐波检测结果中补偿零序电流。理论分析和仿真结果都证明了该方法的正确性。 相似文献
7.
当电网出现故障时,在孤岛检测时,常用的无源检测方法和有源检测方法中的有源频率偏移、滑模频率偏移和输出功率扰动法都存在检测盲区。针对这几种方法在孤岛检测时的缺陷,提出了一种主动式孤岛检测新方法,通过脉动负载改变逆变器并网负荷大小,检测逆变器输出电压、频率等来判断孤岛的发生。通过理论分析了该方法具有检测速度快,对电网无影响,无检测盲区。该方法对多台并网运行的光伏逆变器也同样适用。并通过仿真测试和实际产品试验验证了该方法的有效性。 相似文献
8.
9.
针对有源电力滤波器(APF)设计过程中,在检测谐波电流时要满足实时性强和精确度高的要求,在传统自适应检测方法的基础上,提出了一种先进的三相APF系统补偿电流自适应检测方法。该方法结合了空间矢量变换与自适应干扰对消的原理,克服了传统自适应检测方法存在的固有局限性,具有较强的自适应性,在系统电流严重畸变时,能实时高精度地检测出三相系统中的各相谐波分量,同时可检测出基波正、负序分量。文中详细分析了检测电路的频率特性,该检测电路采用锁相环产生参考电压和在积分器前串接低通滤波器,并通过广义矢量变换矩阵取代传统变换矩阵的方法,大大提高了系统检测精度和动态响应特性。该方法同样适应于电压各分量的检测。实验结果证明了该检测方法的正确性和优越性。 相似文献
10.
11.
12.
13.
远场多频涡流技术在金属探伤中的应用 总被引:1,自引:0,他引:1
介绍涡流、远场涡流,多频涡流等探伤方法的基本原理及三者之间的关系,并在此基础上着重介绍了远场涡流在电厂冷凝器铜管、不锈钢管探伤工作中的优点,根据现场检验的经验总结出一套相应的检测方法,并对此方法的工作流程作了详细介绍。 相似文献
14.
超声波探伤中的缺陷精确定位问题是超声波探伤的主要任务之一,文章介绍利用超声波数据采集系统采集的数据,实现对缺陷的大小及位置的精确定量,缺陷的大小由缺陷数据与标准缺陷波数据的比较得出,缺陷的精确定位通过计算超声波在工件中的传播时间求得。 相似文献
15.
Eddy current flaw testing that uses changes in the impedance of the test coil as an electromagnetic field interacts with the test material is a nondestructive testing method. It can be used to inspect test material at high speed without bringing the test coil into contact with the test material. Therefore, it is widely used for product inspection. In the inspection of heat exchanger tubing in power plants and chemical plants, eddy current flaw testing is performed by using an inner probe, because of the structural restrictions of such plants. However, high levels of wobble noise and support plate noise occur in the conventional method using a rotating pancake coil. The authors therefore propose new minimal‐noise eddy current inner probes. Two new types of probes have been developed: one for detecting axial flaws and the other for detecting circumference flaws. These probes can detect flaws with a low level of noise. The phase of the flaw signal by the new probes changes according to the flaw depth. As a result, the signal phase by the new probes can be used for evaluating the depth of surface flaws. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 161(2): 52–61, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20605 相似文献
16.
文章对锅炉受热面同种不锈钢小径管对接焊缝超声波探伤方法的中探头研制,探伤工艺简要阐述,为不锈钢小径管对接焊缝的探伤方法探索出一种可行的途径。 相似文献
17.
介绍了小径管超声波探伤工艺在《电力建设施工及验收技术规范(管道焊接接头超声检验篇》标准基础上的制定过程及在实际探伤中遇到的一些问题,并提出了解决办法。 相似文献
18.
Bobbin-coil-type eddy current probes, which are conventionally used for nondestructive inspection of steam generator tubes in pressurized-water-type nuclear power plants, have poor detection sensitivity to circumferential flaws. Hence a new type of eddy current probe was proposed to effectively detect the magnetic flux component that is indicative of a flaw and thus to eliminate the dependency on sensitivity in flaw detection. In the course of development of the proposed method, probe structures were investigated based on the measurement of magnetic fields induced by variously-shaped excitation flat coils. The new type of probe proposed here consists of differential pick-up coils detecting magnetic flux and excitation coils having a parallelogrammic shape. The structure of the coils was fabricated in order to detect flaws independently of their directions in trial. Nondestructive flaw detection tests were then conducted with the probe. The results obtained concrete evidence showing that both the horizontal, the vertical slit-flaws and even the small hole of 0.5 mm in diameter can be detected successfully. 相似文献
19.
20.
在大修中对马头发电厂# 8炉汽包分散降水管管座角焊缝进行了超声、射线、着色检验 ,检验发现了 12根分散降水管管座角焊缝存在未焊透、未熔合和裂纹缺陷。介绍了分散降水管管座角焊缝超声波检验存在的问题及在检验过程中取得的探伤经验。 相似文献