Synthesis of brush-like CdS nanorod arrays through a novel hydrothermal reaction of simultaneous solvent-oxidation-hydrolysis

Brush-like CdS arrays composed of well-arranged nanorods have been successfully synthesized for the first time through a novel chemical reaction under the low-temperature hydrothermal condition. The reaction can be described as the solvent-oxidation-hydrolysis reaction among Cd, H₂O and thiourea. The products were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and photoluminescence (PL). TEM results showed that these nanorods were about 20?nm wide with lengths varying from 1.25?µm to 3.5?µm. XRD pattern indicated that as-obtained CdS was hexagonal phase with good crystallinity. PL spectrum showed the products had novel optical property from the bulk counterpart. The formation mechanism was also explored.     

Controlled synthesis of LaPO(4) and CePO(4) nanorods/nanowires

LaPO(4) and CePO(4) nanorods/nanowires with controlled aspect ratios have been successfully synthesized using a hydrothermal microemulsion method under mild conditions. It has been shown that the obtained LaPO(4) has a monoclinic structure, while CePO(4) exists in the hexagonal structure. Uniform nanorods/nanowires with diameters of 20-60?nm and lengths ranging from several hundreds of nanometres to several micrometres were obtained. The aspect ratios of the obtained 1D nanostructures can be fine-tuned by simply changing the [H(2)O ]/[surfactant] molar ratios. The possible growth mechanism of LaPO(4) and CePO(4) nanorods/nanowires was explored in detail.     

In situ synthesis and characterization of GaN nanorods through thermal decomposition of pre-grown GaN films

Herein we describe a thermal treatment route to synthesize gallium nitride (GaN) nanorods. In this method, GaN nanorods were synthesized by thermal treatment of GaN films at a temperature of 800?°C. The morphology and structure of GaN nanorods were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that GaN nanorods have a hexagonal wurtzite structure with diameters ranging from 30 to 50?nm. Additionally, GaN nanoplates are also founded in the products. The growth process of GaN nanostructures was investigated and a thermal decomposition mechanism was proposed. Our method provides a cost-effective route to fabricate GaN nanorods, which will benefit the fabrication of one-dimensional nanomaterials and device applications.     

Epitaxial growth of ZnO nanorods on electrospun ZnO nanofibers by hydrothermal method

In this paper, we report a new ZnO nanofibers-nanorods structure which was successfully prepared by the electrospun ZnO nanofibers as seed to guide hydrothermal epitaxial growth of the ZnO nanorods. The structure was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and photoluminescence (PL). The XRD results indicate that ZnO nanofibers obtained at 600° have high crystallinity with a typical hexagonal wurtzite structure. Furthermore compared with the strongest diffraction of ZnO nanofibers in (101) plane, the diffraction from (002) plane of ZnO nanofibers-nanorods becomes the strongest. The SEM shows that the diameters of epitaxial-grown ZnO nanorods on ZnO nanofibers were approximately 100–200?nm. The PL spectrum shows that the ZnO nanofibers-nanorods have a broad green-yellow emission around 537?nm, in contrast to that of ZnO nanofibers, the peak had obvious redshift about 24?nm and the luminous intensity weakened.     

High pressure luminescence and Raman studies on the phase transition of Gd2O3:Eu3+ nanorods

The cubic Gd2O3:Eu3+ nanorods were synthesized by a hydrothermal method. The SEM image indicated the nanorods with diameter of 30-35 nm and length of 200-500 nm. The structural stability of Gd2O3:Eu3+ nanorods was investigated by in situ high pressure luminescence and Raman spectra up to 18.9 GPa at room temperature. The results reveals a pressure-induced phase transition from cubic to hexagonal structure at about 11.3 GPa. After releasing pressure, the part of hexagonal structure is retained and the other transfers to monoclinic phase.     

不同晶型La2O3：Eu3＋纳米棒的制备及发光性质

以阴离子交换树脂为原料,液相反应制备了不同晶型La2O3：Eu3＋纳米棒,通过XRD、SEM、HRTEM和EDS对La2O3：Eu3＋纳米棒进行了分析和表征,结果表明,经650℃焙烧处理后制备的六方La203：Eu3＋纳米棒,直径为40～100nm,长度约2μm;当焙烧温度升高到850℃时,相变为立方相结构;利用D荧光光谱确定La2O3：Eu3＋纳米棒的最佳监测波长和激发波长,观察到在394nm的激发波长下Eu3＋在六方和立方晶型La2O3纳米棒中的主发射峰均为5D0→7F2跃迁,分别位于615nm和625nm处,且Eu3＋在六方相结构中的发光性质优于立方相结构。     

Synthesis of FePt nanorods and nanowires by a facile method

FePt nanorods and nanowires have been synthesized by the reduction of Pt(acac)(2) and the thermal decomposition of Fe(CO)(5) in the presence of solvents/surfactants by simply controlling the sequence of addition of surfactants. The as-synthesized FePt nanorods and nanowires have a face centered cubic structure with average diameter of 3?nm. Length of nanorods and nanowires can be adjusted in the range of 15-150?nm by varying reaction parameters. Nanocrystalline L1(0) FePt phase with coercivity up to 24?kOe was obtained after heat treatments.     

Abnormal photoluminescence properties of GaN nanorods grown on Si(111) by molecular-beam epitaxy

We have studied the photoluminescence properties of GaN nanorods grown on Si(111) substrates by radio-frequency plasma-assisted molecular-beam epitaxy. The hexagonal shaped nanorods with lateral average diameters from 30 to 150?nm are obtained by controlling the Ga flux with a fixed amount of nitrogen. As the diameters decrease, the main emission lines assigned as donor bound excitons are blueshifted, causing a spectral overlap of this emission line with that of the free exciton at 10?K due to the quantum size effect in the GaN nanorods. The temperature-dependent photoluminescence spectra show an abnormal behaviour with an 'S-like' shape for higher diameter nanorods. The activation energy of the free exciton for GaN?nanorods with different diameters was also evaluated.     

Ferromagnetism in Gd-doped CdS dilute magnetic semiconducting nanorods

Cd _x Gd_1?x S (x = 0–0.15) nanorods have been synthesized by solvothermal technique. X-ray diffraction study reveals that pure and Gd-doped CdS nanorods exhibits hexagonal wurtzite structure. Transmission electron microscopy reveals nanorods like morphology of synthesized CdS having 14 and 26 nm size of pure and 15 % doped CdS nanorods. UV–Visible absorption study confirms the blue shift in the energy band energy due to the quantum confinement effects. Photoluminescence spectra confirm the defect free nature of the synthesized nanorods with peaks emerging around 528 and 540 nm due to the green emission. The magnetic study shows that the pure and Gd-doped CdS nanorods exhibits ferromagnetic character and the magnetisation increased by five times from 0.074 to 0.422 emu/g upon Gd-doping.     

Graphene/zinc bismuthate nanorods composites and their electrochemical sensing performance for ascorbic acid

Graphene/zinc bismuthate nanorods composites have been prepared using graphene and zinc bismuthate nanorods as the raw materials. The composites are composed of graphene nanosheets with folds and wrinkles and zinc bismuthate nanorods which possesses cubic ZnBi₃₈O₅₈ and hexagonal graphite phases. The zinc bismuthate nanorods are dispersed on the graphene nanosheets. A pair of quasi-reversible redox cyclic voltammogram (CV) peaks exist at the graphene/zinc bismuthate nanorods composites modified glassy carbon electrode. The CV peak current linearly increases with the scan rate from 25?mV?s^?1 to 200?mV?s^?1. The electrochemical response is linear in the ascorbic acid concentration range of 0.0001-2?mM and the detection limit is 0.07?μM. The graphene/zinc bismuthate nanorods composites can be considered as a promising electrode materials to be utilized as the electrochemical sensor.     

Direct synthesis of highly crystalline single-phase hexagonal tungsten oxide nanorods by spray pyrolysis

The metastable state hexagonal-tungsten oxide (h-WO₃) has been attracting attention over the past decade because of its high reactivity that arises from the hexagonal channels in its crystal structure. Simplification of the process used to synthesize h-WO₃ is an important step to facilitate the industrial applications of this material. In this study, we addressed this challenge by developing a spray pyrolysis process to synthesize highly crystalline h-WO₃. The ratio of the monoclinic to the hexagonal phase was controlled by adjusting the segregation time. Single-phase h-WO₃ nanorods were synthesized using a carrier gas flow rate of 1?L/min, which was equivalent to a segregation time of 18.4?s. The ability of the h-WO₃ nanorods to adsorb nitrogen and carbon dioxide was evaluated to confirm the presence of hexagonal channels in the crystal structure.     

Epitaxial growth of the zinc oxide nanorods, their characterization and in vitro biocompatibility studies

Here, we have synthesized Zinc Oxide (ZnO) nanorods at room temperature using zinc acetate and hexamethylenetetramine as precursors followed by characterization using X-ray diffraction (XRD), fourier transform infra red spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy. The growth of the synthesized ZnO was found to be very close to its hexagonal nature, which is confirmed by XRD. The nanorods were grown perpendicular to the long-axis and grew along the [001] direction, which is the nature of ZnO growth. The morphology of the synthesized ZnO nanorods was also confirmed by SEM. The size of the nanorod was estimated to be around 20-25?nm in diameter and approximately 50-60?nm in length. Our biocompatibility studies using synthesized ZnO showed no significant dose- or time-dependent increase in the formation of free radicals, accumulation of peroxidative products, antioxidant depletion or loss of cell viability on lung epithelial cells.     

Synthesis of violet light emitting single crystalline ZnO nanorods by using CTAB-assisted hydrothermal method

ZnO nanorods were grown by cetyl trimethylammonium bromide assisted hydrothermal technique from a single molecular precursor. The phase and structural analysis were carried out by X-ray diffraction technique and Raman spectroscopy, respectively. The phase and structural analysis has suggested that as prepared nanorods have hexagonal wurzite structure. Morphology of the nanorods was investigated by electron microscopy techniques which showed the formation of well dispersed nanorods of 100 ± 10 nm in diameter and 900 ± 100 nm in length. Optical properties were investigated by photoluminescence spectroscopy. As prepared ZnO nanorods have shown intense room temperature photoluminescence peak in the violet region at 403 nm. Absence of defect mediated green luminescence peak suggests the formation of well crystalline ZnO nanorods without any impurities or structural defects.     

CdS microflowers and interpenetrated nanorods grown on Si substrate: Structural,optical properties and growth mechanism

CdS semiconductor with different morphologies have been achieved by simple thermal evaporation of CdS powder at 1050 °C in a flowing Ar atmosphere. The products were characterized by X-ray diffraction, Scanning electron microscopy, Transmission electron microscopy and Photoluminescence. microflowers and interpenetrative nanorods of CdS were formed on catalyst free Si wafers at a temperature of 700 °C and 600 °C respectively. The flower like structures are composed of many interleaving nanorods which have the uniform diameter of about 700 nm and a well crystalline structure with [0001] as growth direction. The interpenetrative nanorods are found to be bounded with six side facets. X-ray diffraction studies revealed the hexagonal structure in both the products. The formation mechanism of microflowers and interpenetrated nanorods was discussed on the basis of nucleation growth kinetics. Room temperature photoluminescence spectra showed a strong green emission band (at ∼510 nm) from the CdS flower like structures, but on the other hand a red emission shoulder along with strong green emission band was observed for interpenetrative nanorods. These CdS micro/nanostructures with abundant morphologies may find applications in various micro/nanodevices, and the kinetics-driven morphology might be exploited to synthesize similar structures of other functional II–VI semiconductors.     

Microstructure Characterization of Single-crystal ZnO Nanorods Synthesized by Solvothermal at Low Temperature

Single-crystalline ZnO nanorods have been synthesized by a simple solvothermal process at low temperature. Transmission electron microscopy （TEM） observations have confirmed that the as-synthesized products have rod-like morphologies with diameters ranging from several nanometers to 30 nm and lengths from 100 nm to 2 μm. Such hexagonal ZnO nanorods are structurally uniform and the growth direction is identified to be [0001]. Growth mechanism of the ZnO nanorods was proposed.     

燃料对溶液燃烧合成ZnO纳米棒微观形貌和光催化性能的影响

以蔗糖、柠檬酸、乙二醇和尿素为燃料, Zn(NO₃)₂为氧化剂/锌源, 采用溶液燃烧法合成ZnO纳米棒。借助XRD、SEM、比表面分析和光谱吸收等测试方法, 考察了不同燃料对粉体的物相组成、微观形貌、比表面积和光催化性能的影响。结果表明: 在点燃温度500℃下, 各燃料配制的前驱体溶液均可发生燃烧反应合成六方相ZnO纳米棒, 其平均径向尺寸小于100 nm, 且以尿素为燃料合成的ZnO晶形更完整, 以蔗糖为燃料合成的ZnO粉体具有最大的比表面积(24.83 m²/g)。光催化实验表明, 以蔗糖为燃料合成的ZnO粉体光催化能力最佳, 在高压汞灯照射60 min条件下, 其对甲基橙溶液(10 mg/L)的降解率可达98.2%, 且光催化反应符合一级动力学方程。     

离子液体[BMIM][BF_4]中CdS纳米棒的合成与表征

以室温离子液体1-甲基-3-丁基咪唑四氟硼酸盐为介质制备了CdS纳米棒,采用X射线衍射和透射电镜对样品进行了结构表征。结果表明所制备CdS纳米棒具有六方相结构,直径为30nm左右,长度为300nm左右。离子液体和长链烷胺的双重作用促使了CdS一维棒状结构的形成。离子液体同时起到了修饰剂和导向剂的作用。     

Synthesis and characterization of LnPO4 x nH2O (Ln = La, Ce, Gd, Tb, Dy) nanorods and nanowires

Aqueous precipitation method has been used to synthesize lanthanide orthophosphates LnPO4 x nH2O (Ln = La, Ce, Gd, Tb, Dy) with high purity and yield. It has been shown by XRD, TGA, and FTIR characterization that the as-synthesized samples are the LnPO4 hydrates (LnPO4 x nH2O) with hexagonal rhabdophane-type structure. The X-ray diffraction peaks and absorption of PO4(3-) groups show a systematic shift from LaPO4 x nH2O to DyPO4 x nH2O due to the effect of lanthanide ionic contraction. The value of n in LnPO4 x nH2O depends on the lanthanide element and synthetic condition. Field-emission scanning electron microscopy observations show the morphology of as-synthesized samples, which consist entirely of nanorods/nanowires with diameters of 30-100 nm and lengths ranging from several hundreds of nanometers to several micrometers. The anisotropic growth of crystals should be responsible for the formation of nanorods/nanowires, which is related to the hexagonal crystal structure.     

Preparation of anisotropic transition metal phosphide nanocrystals: the case of nickel phosphide nanoplatelets, nanorods, and nanowires

We have synthesized anisotropic nickel phosphide nanocrystals, including triangular/hexagonal nanoplatelets, nanorods and nanowires, via a solution-phase synthetic method that uses nickel(II) acetylacetonate as a metal precursor and trioctylphosphine as a phosphorus source. Nickel phosphide nanoplatelets have been prepared from a one-pot reaction, and their dimensions in the length mostly vary from 20 to 50 nm, while their thicknesses are in a narrow range of 7-9 nm. Nickel phosphide nanorods with a width of approximately 6 nm and a typical length of 25-32 nm can be synthesized from either the one-pot reaction or the multi-injection approach, although the latter can generate nanorods with a much higher uniformity. A continuous injection approach has been used to synthesize nanowires that have a typical width of approximately 6 nm and a length ranging from tens of nanometers up to several hundred nanometers. Major factors that influence the growth of nickel phosphide nanocrystals have been investigated, and a multi-surfactant system is found to be essential for the formation of anisotropic nanostructure. Magnetic studies have revealed paramagnetic characteristics for all the synthesized samples.     

ZnO纳米棒Al掺杂和A1,N共掺杂的制备技术与光致发光性能

采用水热法首先合成了Al掺杂ZnO(AZO)纳米棒,在此基础上通过550℃的氨气氛中退火制备了Al,N共掺杂ZnO(ANZ())纳米棒.运用X射线衍射(XRD),场发射扫描电镜(FESEM),透射电子显微镜(TEM),X射线能谱(EDS)和光致发光(PL)对样品进行了表征与分析.结果表明,制备的AZO和ANZ()纳米棒...