热载荷下金属间化合物厚度对焊点可靠性的影响

研究了在热循环载荷条件下,不同厚度的金属间化合物IMC(Intermetallic Compound)层对焊点可靠性的影响。采用Anand本构模型描述无铅焊点在热载荷条件下的粘塑性力学行为,运用有限元模拟电子封装器件在热载荷循环下的应力应变的变化规律,确定关键焊点的位置,得到关键焊点的关键点的应力、应变与时间关系的曲线,分析IMC层厚度与寿命关系曲线,并确定其函数关系。研究表明:在热载荷条件下IMC层厚度越大,其焊点的可靠性越低,寿命越短。在IMC层厚度为8.5μm时,IMC厚度对焊点寿命的影响率出现明显的变化,影响率由–32.8突然增加到–404,当IMC厚度为14.5μm时,焊点的寿命值出现了跳跃。     

Interaction of intermetallic compound formation in Cu/SnAgCu/NiAu sandwich solder joints

The interaction between Cu/solder interface and solder/Ni interface at a Cu/SnAgCu/NiAu sandwich solder joint with various surface finishes and solder heights was investigated. The interfacial microstructure and composition of intermetallic compounds (IMCs) were characterized by a scanning electron microscope (SEM) equipped with energy-dispersive x-ray spectroscopy (EDX). The phase structure of IMC was identified by x-ray diffraction (XRD). It is found that ternary (Cu,Ni)₆Sn₅ IMCs form at both interfaces. The composition, thickness, and morphology of the ternary IMCs depend not only on the interface itself, but also on the opposite interface. That is to say, strong coupling effects exist between the two interfaces. Lattice parameters of (Cu,Ni)₆Sn₅ shrink with increasing Ni content, in agreement with Vegard’s law. The mechanism of ternary IMC formation and interface coupling effects are discussed in this paper.     

PCB粘弹性对QFN焊点可靠性的影响

基于动态拉伸DMA实验所获得的FR—4PCB的蠕变柔量曲线,用广义Maxwell模型表征了PCB的粘弹性蠕变松弛特性。通过有限元软件MSC Marc分别模拟了基于PCB弹性和粘弹性两种不同性质下,QFN器件在–55～+125℃热循环条件下的应力应变,并利用修正后的Coffin-Masson方程分别计算了它们的热疲劳寿命。结果表明,基于粘弹性条件下QFN焊点可靠性模拟结果更接近实际情况。     

Effect of voids on the reliability of BGA/CSP solder joints

Voids in solder joints have been considered as a defect in electronics assembly. The factors that affect void formation are complex and involve the interaction of many factors. There are no established standards for void size and void area in a solder joint for it to be deemed defective. Inspection criteria have been very subjective. The effect of voids on the reliability of solder joint may depend not only on the size, but also on frequency and location. This study is focussed on investigating the effect of voids on the reliability of solder joints. The size, location and frequency effects on the reliability were studied. Testing was done by mechanical deflection testing (torsion) system and air to air thermal cycling (−40 °C/125 °C). Failures were analyzed for the failure modes by cross sectional analysis. The results indicate that voids reduce the life of the solder joint. Voids which are greater than 50% of the solder joint area, decrease the mechanical robustness of the solder joints. Small voids also have an effect on the reliability, but it is dependent on the void frequency and location.     

Interfacial reaction and mechanical reliability of PTH solder joints with different solder/surface finish combinations

The effects of minor Ni addition (0.05 wt.%) on the microstructures and mechanical reliability of the lead-free solder joints used in the pin through hole (PTH) components were carefully investigated using a scanning electron microscope (SEM), a field-emission electron probe x-ray microanalyzer, and a pull tester. The PTH walls (i.e., Cu) of printed circuit boards (PCBs) were coated with organic solderability preservative (OSP) or electroless nickel/immersion gold (ENIG) surface finish before soldering. During soldering, the pins of the electronic components were first inserted into the PTHs deposited with OSP or ENIG, and then joined using a Sn–3Ag–0.5Cu (SAC) solder bath through a typical wave-soldering process. After wave soldering, a rework (the second wave soldering) was performed, where an SAC or Sn–0.7Cu–0.05Ni (SCN) solder bath was employed. The SCN joints were found to possess a higher tensile strength than the SAC ones in the OSP case. The sluggish growth of Cu₃Sn, along with few Kirkendall voids at the solder/Cu interface caused by minor Ni addition into the solder alloy (i.e., SCN), was believed to be the root cause responsible for the increase in the strength value. However, the mechanical strength of the PTH components was revealed to be insensitive to the solder composition in the alternative case where an ENIG was deposited over the PTH walls. The implication of this study revealed that minor addition of Ni into the solder is beneficial for the solder/Cu joints, but for the solder/Ni(P) joints.     

Effects of thermomechanical cycling on lead and lead-free (SnPb and SnAgCu) surface mount solder joints

Accelerated reliability tests have been performed on leadless and leaded lead-free and lead containing SMT component assemblies. Results so far have shown that lead-free reflow soldering is a viable alternative for conventional lead based reflow soldering. The selected ternary eutectic solder alloy SnAg3.8Cu0.7 requires higher processing temperatures which could restrict the use of certain board and component types, but other than that no major modifications seem necessary. Although better SnAg3.8Cu0.7 bulk mechanical properties were obtained compared to the near eutectic lead bearing bulk solder properties, reflowed solder joints did not reflect this difference. In general, quite similar reliability results were obtained as found for the lead based solders. Dependent on board and component metallisations and use environment, the reliability of the lead-free solders could perform better or worse than the lead based solders. Temperature dependent aspects such as solderability and mechanical behaviour of the lead-free assemblies could play a role in this. Although microstructural differences can be seen between the lead-free and lead bearing solder joints, similar joint failure mechanisms occur. Resistor solder joint cracks propagate from underneath the component through either transgranular (lead-free) grains or along intergranular (lead) grain boundaries between lead-rich and tin-rich areas and into coarsened regions near the component terminations. Gullwing lead cracks were seen propagating from the heel fillet along the lead/solder interfacial intermetallic mostly (some cracks started in the heel fillet and propagated through the solder body dispersed with coarsened spherical Ag₃Sn intermetallic particles). Package design and leadframe material seem to play a more important role in the fatigue mechanism than the change in microstructure of the solder joint.     

Finite element based fatigue life estimation of the solder joints with effect of intermetallic compound growth

This paper develops an analysis procedure to study the effects of intermetallic compound (IMC) growth on the fatigue life of 63Sn-37Pb (lead-rich)/96.5Sn-3.5Ag (lead-free) solder balls for flip-chip plastic ball grid array packages under thermal cycling test conditions. In this analysis procedure, the thickness of the IMC increased with the number of thermal cycles, and was determined using the growth rate equation. A series of non-linear finite element analyses was conducted to simulate the stress/strain history at the critical locations of the solder balls with various IMC thicknesses in thermal cycling tests. The simulated stress/strain results were then employed in a fatigue life prediction model to determine the relationship between the predicted fatigue life of the solder ball and the IMC thickness. Based on the concept of continuous damage accumulation and incorporated with the linear damage rule, this study defines the damage of each thermal cycle as the reciprocal of the predicted fatigue life of the solder joints with the corresponding IMC thickness. The final fatigue failure of the solder ball was determined as the number of cycles corresponding to the cumulative damage equal to unity. Results show that the solder joint fatigue life decreased as the IMC thickness increased. Moreover, the predicted thermal fatigue life of lead-rich solders based on the effects of IMC growth is apparently smaller than that without considering the IMC growth in the reliability analysis. Results also show that the influence of the IMC thickness on the fatigue life prediction of the lead-free solder joint can be ignored.     

Effect of geometry and temperature cycle on the reliability of WLCSP solder joints

The wafer level-chip-scale package (WLCSP) is designed to have external dimensions equal to that of the silicon device. This new package type is an extension of flip chip packaging technology to standard surface mount technology. The package has been targeted for low pin count (less than 30) and has high volume applications such as cellular phones, hand-held PDAs, etc. The WL-CSP is typically used without underfill and so solder joint reliability is a prime concern. Thus it is imperative to have a good understanding of the various design parameters of the package that affect the reliability of the solder joint. This paper presents the effect of geometrical parameters such as die size, die thickness, solder joint diameter and height on the reliability of solder joints. The effects of different dwell times, temperature range and ramp rates on the reliability of the solder joints is also studied by applying different temperature cycles to the package. A 16 I/O ADI WLCSP called MicroCSP is used as the primary test vehicle for the thermal cycling tests performed with different ramp/hold profiles. The energy-based model developed by Robert Darveaux is used to assess the reliability of solder joints.     

Effect of substrate metallization on interfacial reactions and reliability of Sn-Zn-Bi solder joints

The scope of this paper covers a comprehensive study of the lead-free Sn-Zn-Bi solder system, on Cu, electrolytic Ni/Au and electroless Ni(P)/Au surface finishes. This includes a study of the shear properties, intermetallic compounds at the substrate-ball interface and dissolution of the under bump metallization. The Sn-8Zn-3Bi (wt.%) solder/Cu system exhibited a low shear load with thick IMCs formation at the interface. The dissolution of the Cu layer in the Sn-Zn-3Bi solder is higher than that of the other two Ni metallizations. It was found that the formation of a thick Ni-Zn intermetallic compound (IMC) layer at the solder interface of the electrolytic Ni bond pad reduced the mechanical strength of the joints during high temperature long time liquid state annealing. The solder ball shear-load for the Ni(P) system during extended reflow increased with an increase of reflow time. No spalling was noticed at the interface of the Sn-Zn-3Bi solder/Ni(P) system. Sn-8Zn-3Bi solder with electroless Ni(P) metallization appeared as a good combination in soldering technology.     

Controlling intermetallic compound growth in SnAgCu/Ni-P solder joints by nanosized Cu6Sn5 addition

Nanosized Cu₆Sn₅ dispersoids were incorporated into Sn and Ag powders and milled together to form Sn-3Ag-0.5Cu composite solders by a mechanical alloying process. The aim of this study was to investigate the interfacial reaction between SnAgCu composite solder and electroless Ni-P/Cu UBM after heating for 15 min. at 240°C. The growth of the IMCs formed at the composite solder/EN interface was retarded as compared to the commercial Sn3Ag0.5Cu solder joints. With the aid of the elemental distribution by x-ray color mapping in electron probe microanalysis (EPMA), it was revealed that the SnAgCu composite solder exhibited a refined structure. It is proposed that the Cu₆Sn₅ additives were pinned on the grain boundary of Sn after heat treatment, which thus retarded the movement of Cu toward the solder/EN interface to form interfacial compounds. In addition, wetting is an essential prerequisite for soldering to ensure good bonding between solder and substrate. It was demonstrated that the contact angles of composite solder paste was <25°, and good wettability was thus assured.     

A reliability comparison of electroplated and stencil printed flip-chip solder bumps based on UBM related intermetallic compound growth properties

The effects of under bump metallurgy (UBM) microstructures on the intermetallic compound (IMC) growth of electroplated and stencil printed eutectic Sn-Pb solder bumps were investigated. The process parameters and their effects on UBM surface morphology and UBM shear strength were studied. For the electroplating process, the plating current density was the dominant factor to control the Cu UBM microstructure. For the stencil printing process, the zincation process has the most significant effect on the Ni UBM surface roughness and Ni grain sizes. In both processes, the good adhesion of UBM to aluminum can be obtained under suitable UBM processing conditions. Samples with different UBM microstructures were prepared using the two processes. The resulting samples were thermal aged at 85/spl deg/C, 120/spl deg/C, and 150/spl deg/C. It was observed that the Cu UBM surface roughness had larger effect on the IMC growth and solder ball shear strength than the Ni UBM surface roughness. The thickness of Cu/sub 3/Sn and Cu/sub 6/Sn/sub 5/ IMC depended strongly on the UBM microstructure. However, for Ni/Au UBM, no significant dependence was observed. More likely, the thickness of Au-Ni-Sn IMC near the IMC/solder interface was controlled by the amount of gold and the gold diffusion rate in the solder. Shear tests were performed after thermal aging tests and thermal/humidity tests. Different failure modes of different sample groups were analyzed. Electroless Ni UBM has been developed because it is a mask-less, low-cost process compared to electroplated Cu UBM. This study demonstrated that the process control was much easier for Ni UBM due to its lower reactivity with Sn material. These properties made Ni UBM a promising candidate for the lead-free solder applications.     

A quantitative method of reliability estimation for surface mount solder joints based on heating factor Qη

A novel method of reliability analysis on thermal fatigue failure for surface mount solder joints, based on the heating factor Q_η, is presented, by which quantitative reliability estimation and prediction of solder joints suffering from cyclic thermal stress can be done. Based on the typical lifetime data of thermal cycling test, the relationship of the mean time to failure (MTTF) as well as the reliability of solder joints as an explicit function of Q_η is deduced and presented in a unified mathematic form. Numerical calculations are performed, and the result shows that the MTTF decreases quickly with the increases in heating factor and then slowly approximates to a constant value when Q_η  1500 s °C. The solder joint reliability in terms of thermal cycle degrades in an analogical fashion for different heating factors. For any given thermal cycle, calculation suggests that to obtain a higher reliability, a lower heating factor should be controlled during soldering. The presented method gives an applicable solution and can be used for online reflow control in industry. On the one hand, an ideal reflow profile can be achieved by properly controlling heating factor during soldering to meet the given reliability goal. On the other hand, the life expectancy of solder joints can be approximately estimated and predicted from a known reflow profile with a specified heating factor. Finally, for a specified reliability goal, how to properly choose and control heating factor during soldering to achieve reliable solder joints is discussed.     

Microstructure coarsening during static annealing of 60Sn40Pb solder joints: III intermetallic compound growth kientics

The growth of the total (Cu₃Sn+Cu₆Sn) intermetallic compound layer in Cu-60Sn40Pb solder joints during static annealing at 50°C to 150°C was described by the equation hi=h_o+A_o exp(−Q_a/RT)t^p with h_o=0–0.3 μm, p=0.38–0.70, A_o=1.9×10⁻⁴–3.4×10⁻⁴ m/s^p, and Q_a=25.5–30.9 kJ/mole. These constants are within the range of those obtained by others and give values of D_o and Q which are in reasonable accord with those for the diffusion coefficients in Cu₃Sn and Cu₆Sn₅ determined in diffusion couples. The deviation of the values of the time exponent p from the ideal of 0.5 for diffusion growth may be due to inaccuracies or errors pertaining to the measured thickness (especially h_o) and the complex nature of the diffusion process.     

Morphology and mechanical properties of intermetallic compounds in SnAgCu solder joints

This paper presents the studies to determine hardness and elastic modulus of intermetallic compound (IMC) layers in lead-free solder joints using nanoindentation technique. Two types of surface finishes, i.e., organic solderability preservative (OSP) and electrolytic Ni/Au on Cu pad, with Sn3.5Ag0.5Cu solder balls of 330 μm in diameter are studied, and the intermetallic layers are identified to be Cu₆Sn5, Cu₃Sn and (Ni_y,Cu_1−y)₃Sn₄. The thicknesses of these IMC layers are only few microns at reflowed conditions (less than 2.3 μm). Therefore, probing mechanical properties of thinner IMCs using nanoindentation techniques poses immense difficulties and challenges. In this study, taper-mounted samples are used rather than standard cross-sectional mounted for solder joints. This taper sample gives a larger area for nanoindentation measurements. The elastic modulus and hardness of IMC layers are determined based on the parameter P/S² (load/stiffness²) as a function of the indentation depth to minimise the effects of underlying UBM or solder materials. The modulus of Cu₆Sn₅, Cu₃Sn, (Cu_x,Ni_1−x)₆Sn₅ and (Ni_y,Cu_1−y)₃Sn₄ layer are found to be 112.0 ± 5.1 GPa, 135.5 ± 4.3 GPa, 165.0 ± 11.3 GPa and 136.8 ± 5.8 GPa; whereas the hardness values are found to be 6.8 ± 0.4 GPa, 6.6 ± 0.5 GPa, 7.2 ± 0.9 GPa and 8.2 ± 1.0 GPa, respectively. Thus, the IMC layers in the order of increasing hardness and modulus are found to be Cu₆Sn₅, Cu₃Sn, (Cu_x,Ni_1−x)₆Sn₅ and (Ni_y,Cu_1−y)₃Sn₄.     

An investigation on thermal reliability of underfilled PBGA solder joints

The failure mechanism, as well as cycles to failure, of two groups of PBGA samples (with/without underfill) for thermal shock in the range of -40/spl square/-125/spl square/ were presented. The experiment shows that the solder ball in the samples without underfill cracked after 500 times cycle, while no crack was found in the underfilled samples even after 2700 cycles. However, the die attach layer delaminated after 500 cycles and the PCB cracked in the underfilled samples after long time cycling. C-SAM is employed to investigate the delamination in the underfilled samples. Highly concentrated stress-strain induced by the CTE mismatch between the BGA component and the PCB, coarsened grain and two kinds of intermetallic compounds (Ni/sub 3/Sn/sub 2//NiSn/sub 4/) which formed during reflow and thermal cycling and their impact on the reliability of solder joints are discussed in this paper. The initiation of the crack and its propagation are also presented in this paper. By means of dye penetrant test, the authors reveal the distribution of microcracks in the solder ball array. In addition, this paper includes results of simulation, which further verified its conclusions.     

Effects of intermetallic morphology at the metallic particle/solder interface on mechanical properties of Sn-Ag-based solder joints

Mechanical incorporation of metallic particles in the Sn-Ag-based solder resulted in various intermetallic compound (IMC) morphologies around these particles during reflow. Unlike with the Ni particles, the IMCs formed around Cu and Ag particles are relatively insensitive to reflow profiles employed. The IMC formed around the Ni particles ranges from “sunflower” morphology to “blocky” morphology with increasing time and temperature above liquidus during the heating part of the reflow profile. Mechanical properties, such as simple shear strength and creep behavior, of these composite solders were affected by the IMC morphologies in the composite solders investigated. Sunflower-shaped IMC formed around an Ni particles resulted in higher simple shear strength and better creep properties.     

Mechanical properties of intermetallic compounds associated with Pb-free solder joints using nanoindentation

Mechanical properties of intermetallic compound (IMC) phases in Pb-free solder joints were obtained using nanoindentation testing (NIT). The elastic modulus and hardness were determined for IMC phases associated with insitu FeSn particle reinforced and mechanically added, Cu particle-reinforced, composite solder joints. The IMC layers that formed around Cu particle reinforcement and at the Cu substrate/solder matrix interface were probed with NIT. Moduli and hardness values obtained by NIT revealed were noticeably higher for Cu-rich Cu₃Sn than those of Cu₆Sn₅. The Ag₃Sn platelets that formed during reflow were also examined for eutectic Sn-Ag solder column joints. The indentation modulus of Ag₃Sn platelets was significantly lower than that of FeSn, SnCuNi, and CuSn IMCs. Indentation creep properties were assessed in localized microstructure regions of the as-cast, eutectic Sn-Ag solder. The stress exponent, n, associated with secondary creep differed widely depending on the microstructure feature probed by the indenter tip.     

Effect of type of thermo-mechanical excursion on growth of interfacial intermetallic compounds in Cu/Sn-Ag-Cu solder joints

This study reports the effect of different types of thermo-mechanical excursion (TME) on growth of intermetallic compound (IMC) layer formed at the interface of Sn-3.0%Ag-0.5%Cu solder and Cu substrate. 1 mm thick solder joints were prepared by reflowing at 270 °C for either 60 or 90 s. Solder joints were then exposed to one of the following TME: (i) isothermal aging at 60 °C for 48, 96 and 144 h, (ii) thermal cycling between − 25 and 125 °C for 100, 200 and 400 cycles, and (iii) thermo-mechanical cycling between − 25 and 125 °C for 100, 200 and 400 cycles, wherein a shear strain of 10% per cycle was imposed on the joint. Finite element analysis (FEA) was performed to ascertain the effects of imposed shear strain and volumetric expansion due to the formation of IMC on the stress field in the solder joint. Irrespective of the type of TME, the thickness of the IMC layer increased with time. However, IMC thickness increased relatively more rapidly under thermo-mechanical cycling condition, indicating strain enhanced coarsening of the interfacial IMC layer. FEA showed that high stresses were generated in the IMC layer and near solder-IMC interface due to the formation of IMC layer as well as imposed external strain, which might then not only enhance the IMC growth kinetics, but also affect the morphology of the IMC layer.     

Effect of isothermal aging and low density current on intermetallic compound growth rate in lead-free solder interface

This study investigated the effects of isothermal aging and low density current on intermetallic compound (IMC) growth rate and microstructural evolution of lead-free solder interface at a temperature of 398 K. The results showed that the morphology of IMC layers under high temperature aging and current stressing was basically same. The growth rate of IMC at the anode was the fastest. That was because chemical diffusion force and electronic wind acted together to drive the growth of IMC at the anode. The current density was not high enough for obvious polarization effects and crack along the electron flow direction to be observed. Next the mean-time-to-failure analysis was used to calculate the lifetime of ball grid array solder joints stressed electrically. However, the calculated value was much shorter than the true value. Indicating that perhaps the equation needs to be modified when applied to Cu interconnects and flip chip solder joints.