Equilibrium modeling,kinetic and thermodynamic studies on the adsorption of Cr(VI) using activated carbon derived from matured tea leaves

A new porous carbon with high surface area of 1,313.41 m² g^?1 with pore volume 1.359 cm³ g^?1 has been synthesized from matured tea leaves by chemical activation method using phosphoric acid. The carbon was found to be highly efficient for removal of Cr(VI) from aqueous solution. The effects of various parameters such as contact time, initial metal ion concentration, pH, temperature and amount of adsorbent on the extent of adsorption were studied. Langmuir, Freundlich and Temkin adsorption models were used to interpret the experimental data. The adsorption data were best fitted with Langmuir isotherm model. The adsorption capacity of Cr(VI) onto the activated carbon calculated from Langmuir isotherm was found to be 30.8 mg g^?1 at pH 4.8 and temperature 303 K. The adsorption capacity increases from 25.36 to 32.04 mg g^?1 with an increase in temperature from 303 to 323 K at initial Cr(VI) concentration of 60 mg L^?1. The adsorption process followed a pseudo second order kinetic model. Thermodynamic parameters ΔH⁰ (28.6 KJ mol^?1), ΔG⁰ at three different temperatures [(?0.145, ?1.09, ?2.04) KJ mol^?1] and ΔS⁰ (94.87 J mol^?1 K^?1) were calculated. These values confirm the adsorption process to be endothermic and spontaneous in nature.     

Surface Porosity of Lignin/PP Blend Carbon Fibers

Abstract

The surface porosities of carbon fibers derived from the polymer blend fibers of hardwood kraft lignin, HKL and polypropylene, PP, were discussed using thermal analyses, FTIR, and nitrogen adsorption. HKL/PP carbon fibers were prepared by two‐step thermal processing, thermostabilization, and carbonization. During the thermostabilization process, pores are created by oxidative degradation of the PP component. After thermostabilization some crystalline and highly oxidized PP components remained in the blend fiber. These residual PP components were subsequently pyrolyzed during carbonization, and effectively created a porous structure in the resulting carbon fibers. N₂ adsorption tests of the porous carbon fibers revealed the same type of adsorption/desorption isotherms as for activated carbon fiber. The internal surface area of the HKL/PP = 62.5/37.5 carbon fibers was calculated to be 499 m² g^?1. This value was lower than that for commercial activated carbon, 745 m² g^?1. However, these porous lignin‐based carbon fibers were not activated carbon fibers, which could be relatively easily done through steam activation. Thus, the HKL/PP blend carbon fibers appear to be promising precursors for activated carbon fibers.     

Solvothermal synthesis of porous conjugated polymer with high surface area for efficient adsorption of organic and biomolecules

Aimed to prepare high efficient dye sorbent and control water pollution, herein we utilized solvothermal method to synthesize porous polyimide (PI) polymer with a large surface area using DMSO as solvent. Unlike the solid-state thermal polymerized PI with low surface area of 5 m²g^?1, this PI material prepared in DMSO solvent possessed a large surface area of 430 m²g^?1, which was beneficial for adsorption of organic dye in waste water, achieving a max MO adsorption of 200 mg g^?1 three times higher than that of multiwalled carbon nanotube. The adsorption kinetics of dye molecules on PI was investigated in detail and the R² value of 0.99071 for pseudo-second-order model confirms the adsorption was fitted best with Langmuir isotherm.     

SYNTHESIS OF ACTIVATED CARBON FROM JATROPHA SEED COAT AND APPLICATION TO ADSORPTION OF IODINE AND METHYLENE BLUE

This article provides evidence that jatropha seed coat residues can be used as a carbon source for preparing activated carbons that have good adsorption properties for iodine and methylene blue. Activated carbons were prepared using three different methods of activation, physical, chemical, and physico-chemical, for a range of activation temperatures (600°, 700°, 800°, and 900°C) and activation hold times (1, 2, and 3 h). The highest BET surface area (1479 m² g^?1) and the highest iodine adsorption (1511 mg g^?1) were obtained with physico-chemical activation at a temperature of 900°C and a hold time of 2 h. This activated carbon gave higher BET surface area and iodine adsorption than commercial activated carbon (1169.1 m² g^?1 and 1076 mg g^?1). The activated carbons prepared by physico-chemical activation at 900°C and 2 h were then tested for adsorption of methylene blue at a range of concentrations of methylene blue (100, 200, 300, 400, and 500 mg L^?1). It was found that a Langmuir isotherm gave a better fit (R ² = 0.999) to the observed adsorptions than a Freundlich isotherm (R ² = 0.884). For the adsorption kinetics, a pseudo-second-order model gave a better fit (R ² > 0.998, Δq _e  = 3.7%) than a pseudo-first-order model (R ² ≈ 0.95, Δq _e  = 85.6%). These results suggest that chemisorption is the rate-controlling step for the adsorption of methylene blue. The experimental results show that jatropha seed coat is a lignocellulosic waste precursor for preparation of activated carbon that is an alternative source for preparation of commercial-grade activated carbons.     

Nanoporous rice husk derived carbon for gas storage and high performance electrochemical energy storage

We report on the gas storage behaviour and electrochemical charge storage properties of high surface area activated nanoporous carbon obtained from rice husk through low temperature chemical activation approach. Rice husk derived porous carbon (RHDPC) exhibits varying porous characteristics upon activation at different temperatures and we observed high gas uptake and efficient energy storage properties for nanoporous carbon materials activated even at a moderate activation temperature of 500 °C. Various experimental techniques including Fourier transform-infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, high resolution transmission electron microscopy and pore size analyser are employed to characterise the samples. Detailed studies on gas adsorption behaviour of CO₂, H₂ and CH₄ on RHDPCs have been performed at different temperatures using a volumetric gas analyser. High adsorption capacities of ~9.4 mmol g^?1 (298 K, 20 bar), 1.8 wt% (77 K, 10 bar) and ~5 mmol g^?1 (298 K, 40 bar) were obtained respectively for CO₂, H₂ and CH₄, superior to many other carbon based physical adsorbents reported so far. In addition, these nanoporous carbon materials exhibit good electrochemical performance as supercapacitor electrodes and a maximum specific capacitance of 112 F g^?1 has been obtained using aqueous 1 M Na₂SO₄ as electrolyte. Our studies thus demonstrate that nanoporous carbon with high porosity and surface area, obtained through an efficient approach, can act as effective materials for gas storage and electrochemical energy storage applications.     

Biosorption of Strontium Ions by Magnetically Modified Yeast Cells

The sorption of Sr²⁺ ions from aqueous solutions on magnetically modified fodder yeast (Kluyveromyces fragilis) cells and their subsequent desorption were studied. The Sr²⁺ sorption increased with increasing pH and reached a plateau between pH 4.0 and 7.0. The changes of temperature slightly influenced the sorption process. The sorption values were 19.5 mg g^?1 and 53.5 mg g^?1 for 10 mg L^?1 and 40 mg L^?1 Sr²⁺ solutions respectively after 20 min incubation at a pH higher than 4. The Langmuir isotherm was successfully used to fit experimental data; the maximum adsorption capacity was 140.8 mg g^?1 under optimal conditions. The adsorbed Sr²⁺ ions can be desorbed with nitric acid (0.1 mol L^?1).     

Preparation and molten salt-assisted KOH activation of porous carbon nanofibers for use as supercapacitor electrodes

Carbon nanofiber paper was prepared by electrospinning from thermosetting phenolic resin, followed by activation via KOH-containing molten salt at high temperature. By adding a small dosage of KOH in the molten salt the porous volume and specific surface area could be greatly improved. The obtained porous carbon nanofibers had a specific surface area of 1007 m² g^?1, total pore volume of 0.363 cm³ g^?1, micropore volume of 0.247 cm³ g^?1. The electrochemical measurements in 6 M KOH aqueous solution showed that the porous carbon nanofibers possessed high specific capacitance and considerable rate performance. The maximal specific capacitance of 288 F g^?1 was achieved at 0.2 A g^?1 and the specific capacitance could still remain 204 F g^??1 at 20 A g^?1 with the retention of 71%. In the molten salt system, the reaction between activating agent and carbon could be more efficient, hence, such molten salt-assisted activation method was considered as a general activation method for the high-specific-surface-areaed carbons.     

Hypercrosslinked porous polyporphyrin by metal-free protocol: characterization,uptake performance,and heterogeneous catalysis

Through metal-free protocol, hypercrosslinked porous polyporphyrin with permanent porosity was obatined via the Friedel–Crafts alkylation of tetracarbazolylporphyrin using formaldehyde dimethyl acetal as an external cross-linker. Its chemical structure and porosity was well characterized and confirmed. The BET specific surface area value of HCP-TCPP is 1050 m² g^?1 and related dominant pore size is centered at 0.63 nm. The adsorption amount of methanol by HCP-TCPP is high up to 800 mg g^?1 (about 25.0 mmol g^?1) at its saturated vapor pressure, which is higher than that of toluene (600 mg g^?1, 6.5 mmol g^?1). Further study indicates that polymer HCP-TCPP, possessing the high BET specific surface area and total pore volume, exhibits good hydrogen uptake of 3.44 wt % (77 K) and high carbon dioxide uptake of 41.1 wt % (298 K) at 18.0 bar. Besides, the obtained porous polymer can also be used as an effective heterogeneous catalyst for the Knoevenagel condensation between various aldehydes and malononitrile.     

Unexploited Thapsia garganica,Orlaya maritima,and Retama raetam Seeds: Potential Sources of Unsaturated Fatty Acid and Natural Antioxidants

Total lipid contents, fatty acid compositions, phenolic profiles and antioxidants activities of seeds from Thapsia garganica, Orlaya maritima, and Retama raetam were investigated. The oil values were more than 26 %, except seeds of R. raetam (ca. 3 %). Unsaturated fatty acids accounted for the majority of the fatty acids (more than 75 %). Oleic and linoleic acid were the predominant fatty acids. Total phenolic compounds (24–104 mg GAE g^?1 DR), total flavonoids (4–102 mg QE g^?1g DR), total tannins (28–85 mg GAE g^?1 DR) and condensed tannins (0.62–131 mg CE g^?1 DR) were also determined. The antioxidant activities using different assays were evaluated. The predominant detected classes were the phenolic acids (42–85 %) and the flavonoids (11–48 %). The major phenolic acids were caffeic, trans‐4‐hydroxy‐3‐methoxycinnamic, p‐coumaric, and gallic acid. The predominant flavonoids were quercetin, luteolin, naringin, apigenin, and kaempferol. This study brings attention to the medicinal importance of these species as a source of oil and antioxidant molecules.     

Application of mesoporous magnetic nanosorbent developed from macadamia nut shell residues for the removal of recalcitrant melanoidin and its fractions

ABSTRACT

A novel mesoporous magnetic nanosorbent developed from macadamia nut shell residues was applied as an adsorbent for the removal of dissolved organic carbon (DOC) associated with melanoidin and its fractions in a batch system. The most favored molecular fraction of the melanoidin for adsorption onto the nanosorbent was 1–5 kDa with adsorption capacity of 10.26 mg DOC g^?1 achieving 68.4% removal efficiency. The sorption behaviors were all well fitted to a pseudo-second-order kinetic model and Langmuir isotherm. Optimum operating conditions needed for the maximum uptake of 14.7 mg DOC g^?1 were found to be pH of 6.3, temperature of 41.7°C at the dosage of the magnetic nanosorbent of 877.7 ppm.     

Fabrication of the nitrogen doped ordered porous carbon derived from amino-maltose with excellent capacitance performance

In this paper, pristine and nitrogen doped ordered porous carbon materials were fabricated by using maltose and amino-maltose synthesized by hydrothermal reaction as precursors via template strategy. The fabricated pristine ordered porous carbon (OPC) and nitrogen doped ordered porous carbon (NOPC) exhibit excellent textural properties and good capacitance performance, which specific surface area (S_BET) reach 1107 and 726 m² g^?1 for the pristine OPC and NOPC materials while the specific capacitance reach up to 139 and 183 F g^?1 under a current density of 0.5 A g^?1, respectively. The capacitance retention rate for the pristine OPC and NOPC reaches ca. 81 and 92% as the current density increased from 0.5 to 20 A g^?1, and no apparent capacitance decrease was observed after 5000 cycles. Although a sharp decrease of specific surface area was observed after N doping, the specific capacitance of NOPC was improved about 31% than that of the pristine OPC, the enhanced wettability and surface availability after N doping were found to be responsible for the enhanced capacitance performance of NOPC.     

Adsorption of cadmium and zinc from aqueous solution on natural and activated bentonite

The adsorption of cadmium and zinc ions on natural bentonite heat-treated at 110°C or at 200°C and on bentonite acid-treated with H₂SO₄ (concentrations: 0·5 mol dm^?3 and 2·5 mol dm^?3), from aqueous solution at 30°C has been studied. The adsorption isotherms corresponding to cadmium and zinc may be classified respectively as H and L types of the Giles classification which suggests the samples have respectively a high and a medium affinity for cadmium and zinc ions. The experimental data points have been fitted to the Langmuir equation in order to calcualte the adsorption capacities (X_m) and the apparent equilibrium constants (K_a) of the samples; X_m and K_a values range respectively for 4·11 mg g^?1 and 1·90 dm³ g^?1 for the sample acid-treated with 2·5 mol dm^?3 H₂SO₄ [(B)-A(2·5)] up to 16·50 mg g^?1 and 30·67 dm³ g^?1 for the natural sample heat-treated at 200°C [B-N-200], for the adsorption process of cadmium, and from 2·39 mg g^?1 and 0·07 dm³ g^?1, also for B-A(2·5), up to 4·54 mg g^?1 and 0·45 dm³ g^?1 [B-N-200], for the adsorption process of zinc. X_m and K_a values for the heat-treated natural samples were higher than those corresponding to the acid-treated ones. The removal efficiency (R) has also been calculated for every sample; R values ranging respectively from 65·9% and 8·2% [B-A(2·5)] up to 100% and 19·9% [B-N-200], for adsorption of cadmium and zinc.     

Hierarchically porous graphitic carbon monoliths containing nickel nanoparticles as magnetically separable adsorbents for dyes

The hierarchically porous graphitic carbon monoliths containing nickel nanoparticles (HPGCM‐Ni) were fabricated via multi‐component co‐assembly in polyurethane (PU) foam scaffold associated with a direct carbonization process from triblock copolymer F127, diblock copolymer PDMS‐PEO, phenolic resol, and nickel nitrate and subsequent silicates removal with NaOH solution. The decomposable PU foam scaffold played important role in the process of multi‐component co‐assembly and macrostructure formation. The nickel salts were reduced to metallic Ni nanoparticles during the carbonization process. The obtained HPGCM‐Ni materials exhibited macropores of 100–450 μm, mesopore size of 7.2 nm, BET surface area of 725 m² g^?1, pore volume of 0.74 cm³ g^?1, and saturation magnetization of 2.3 emu g^?1. Using methyl orange as model dye pollutant in water, HPGCM‐Ni samples showed good adsorption capacity of 440 mg g^?1, exhibiting excellent adsorption characteristics desirable for the application in adsorption of dyes and separation under an external magnetic field. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41322.     

Comparative Study of Sc(III) Sorption onto Carbon-based Materials

The sorption behavior of Sc(III) on different materials including activated carbon (AC), carbon nanotubes (CNTs), graphene oxide (GO), and the chelating resin Chelex 100 was investigated. In general, the sorption of scandium increases with increasing pH. For pH in the range from 2.5 to 5.5, the sorption of Sc(III) onto CNTs, GO, and Chelex 100 is quantitative, whereas a significantly lower amount of scandium ions was retained on AC. The specific amount of Sc(III) adsorbed at pH 2 attained 2.1, 2.9, 36.5, and 37.9 mg g^?1 for AC-COOH, Chelex 100, GO, and CNTs-COOH, respectively. At pH 4, a similar value was obtained for oxidized AC (2.2 mg g^?1), whereas the specific amount adsorbed significantly increased for Chelex (23.4 mg g^?1). The highest values were obtained for GO (39.7 mg g^?1) and oxidized CNTs (42.5 mg g^?1). Better kinetic retention was observed at pH 2 for CNTs and GO, whereas at pH 4 the kinetic behavior of Chelex 100, GO, and CNTs toward Sc(III) was comparable.     

Adsorptive removal of cationic dye from aqueous solutions by ZnO/ZnMn2O4 nanocomposite

The ZnO/ZnMn₂O₄ nanocomposite (ZnMn) was used as adsorbent for the removal of cationic dye Basic Yellow 28 (BY28) from aqueous solutions. The adsorbent was characterized by X-ray diffraction, scanning electron microscope, TEM, Fourier transform infrared ray, BET, particle size distribution and zeta potential measurements. The adsorption parameters, such as temperature, pH and initial dye concentration, were studied. Kinetic adsorption data were analyzed using the pseudo-first-order, pseudo-second-order and intraparticle diffusion kinetic models. The Langmuir and Freundlich isotherm models were applied to fit the equilibrium data. The maximum adsorption capacity of BY28 was 48.8 mg g^?1. Various thermodynamic parameters, such as ΔG°, ΔH° and ΔS°, were calculated.     

Role of unburnt carbon in adsorption of dyes on fly ash

Various fly ash samples with different unburnt carbon contents were collected, characterised and tested for adsorption of basic dyes, Methylene Blue and Crystal Violet, in aqueous solution. It was found that unburnt carbon plays a major role in dye adsorption. The mineral matter of fly ash has little adsorption capacity and most of the adsorption capacity of fly ash can be attributed to the unburnt carbon. The fly ash with higher unburnt carbon content will have higher adsorption capacity. For the carbon‐free fly ash, adsorption capacities for Methylene Blue and Crystal Violet are only 2 × 10^?6 mol g^?1 and 1.0 × 10^?6 mol g^?1, respectively, while the adsorption capacities for Methylene Blue and Crystal Violet on carbon‐enriched fly ash are 1.2 × 10^?4 mol g^?1 and 1.0 × 10^?4 mol g^?1, respectively. A two‐site Langmuir adsorption model best describes the adsorption isotherm. Copyright © 2005 Society of Chemical Industry     

PRODUCTION AND CHARACTERIZATION OF POROUS CARBON FROM DATE PALM SEEDS BY CHEMICAL ACTIVATION WITH H3PO4: PROCESS OPTIMIZATION FOR MAXIMIZING ADSORPTION OF METHYLENE BLUE

The potential of date palm pits to be a suitable precursor for preparation of porous carbon was explored in the present work, utilizing phosphoric acid as the activating agent. Experimental methods reported in the literature were chosen with certain modifications in order to simplify the process. Process optimization was performed using the popular response surface methodology (RSM) adopting a Box-Behnken design. Process optimization was intended to maximize the porous carbon yield and the methylene blue (MB) adsorption capacity, with the process variables being the activation temperature, impregnation ratio (IR), and activation time. The structural characteristics were assessed based on nitrogen adsorption isotherms, SEM, and FT-IR, while the adsorption capacity was estimated using MB adsorption. The optimized experimental conditions were identified to be an activation temperature of 400°C, IR of 3, and activation time of 58 min, with the resultant porous carbon having a yield of 44% and MB adsorption capacity of 345 mg/g. The structural characteristics of the porous carbon reveal the BET surface area to be 725 m²/g, with pore volume of 1.26 cc/g, an average pore diameter of 2.91 nm, and total micropore volume of 0.391 cc/g. The popular Langmuir and Freundlich adsorption isotherm models were tested, and a maximum monolayer adsorption capacity of MB was estimated to be 455 mg/g, which compares with the highest for MB reported in literature, evidencing the suitability of porous carbon for adsorption of macromolecular compounds. The low activation temperature and activation time with highest yield render the process technically and economically attractive for commercial use.     

Synthesis and application of nanocomposite Fe3O4@SiO2@CTAB–SiO2 as a novel adsorbent for removal of cyclophosphamide from water samples

ABSTRACT

We present a way of synthesizing nanocomposite Fe₃O₄@SiO₂@CTAB–SiO₂ by employing simple sol–gel technique with selective etching for extreme selectivity adsorption of cyclophosphamide (CP). The transmission electron microscopy (TEM); scanning electron microscopy (SEM); X-ray diffraction (XRD); Fourier transform infrared (FT-IR); vibrating sample magnetometer (VSM); pH_PZC; and Brunauer, Emmett and Teller (BET) techniques were used for nanocomposite characterization. These nanoparticles have an S_BET of 157.8 m² g^?1 and a high saturation magnetization of 67.5 emu g^?1. First, the adsorption system was examined as a function of contact time under various initial CP contents, ionic strength, initial solution pH, adsorbent dose and temperature in batch test. The optimum dose, pH and contact time were obtained to be 0.01 g, 7.0 and 30 min, respectively. Ultimately, experimental isotherm and kinetics data of adsorption of CP onto nanocomposite Fe₃O₄@SiO₂@CTAB–SiO₂ were fitted to classical models. Additionally, it was found that the maximum adsorption process capacity of CP on adsorbent was 342.8 mg g^?1.     

Solvothermal polycondensation of novolacs phenolic-resin to nanopowders and their derived activated nanocarbons as efficient adsorbents for water cleaning

Novolacs phenolic-resin (PF) was easily polycondensed into polymeric powders with sizes and morphologies ranging from microspheres to nanoparticles by a simple solvothermal process without adding any crosslinking agent. Activating the highly divided PF powders by CO₂ resulted in nanosize activated carbons with high specific surface area (2092 m² g^?1) and large pore volume (1.33 cm³ g^?1) while preserving a high carbon yield of about 38 wt%. As for adsorption tests, the micropore-dominated activated nanocarbons exhibited fast and high adsorption capabilities towards both Cr(VI) ions and bulky rhodamine B molecules due to their much improved external surface area and the greatly shortened intra-particle diffusion distance. The equilibrium adsorption amounts of Cr(VI) and RB on the activated nanocarbons as estimated by the Langmuir model were 200 and 990 mg g^?1, achieved within an adsorption time of 30 and 360 min, respectively.     

Adsorption Characteristics of Chitosan-g-Poly(acrylic acid)/Attapulgite Hydrogel Composite for Hg(II) Ions from Aqueous Solution

Batch adsorption experiments were carried out to remove Hg(II) from aqueous solutions using chitosan-g-poly(acrylic acid)/attapulgite hydrogel composites as adsorbents. The factors influencing the adsorption capacity of the composites were investigated. The results indicate that the adsorption equilibrium of the composites can be achieved within about ten minutes and the equilibrium adsorption capacities of the composites with 10, 30, and 50 wt% of attapulgite content were 785.20, 679.63, and 541.06 mg g^?1, respectively. The negative values of ΔG and positive values of ΔH indicate that the adsorption processes are all spontaneous and endothermic.