Electrochemical promotion of toluene combustion on an inexpensive metallic catalyst

Electrochemical promotion of the complete catalytic oxidation of toluene at 310 °C is reported, using a Ag/YSZ/Ag two electrode system where Ag films were deposited on YSZ from AgNO₃ aqueous solution followed by reduction in H₂. After on-stream activation, a non-negligible conversion (about 30%) at OCV is reached and then the rate of the catalytic toluene conversion into CO₂ and H₂O can be multiplied by a factor higher than 1.5, by application of a small negative current (about—4 μA cm⁻²). The associated Faradaic efficiency is very high and may exceed −13,000.     

The phenol steam reforming reaction towards H2 production on natural calcite

The steam reforming of phenol towards H₂ production was studied in the 650–800 °C range over a natural pre-calcined (air, 850 °C) calcite material. The effects of reaction temperature, water, hydrogen, and carbon dioxide feed concentrations, and gas hourly space velocity (GHSV, h⁻¹) were investigated. The increase of reaction temperature in the 650–800 °C range and water feed concentration in the 40–50 vol% range were found to be beneficial for catalyst activity and H₂-yield. A similar result was also obtained in the case of decreasing the GHSV from 85,000 to 30,000 h⁻¹. The effect of concentration of carbon dioxide and hydrogen in the phenol/water feed stream was found to significantly decrease the rate of phenol steam reforming reaction. The latter was probed to be related to the reduction in the rate of water dissociation as evidenced by the significant decrease in the concentration of adsorbed bicarbonate and OH species on the surface of CaO according to in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS)-CO₂ adsorption experiments in the presence of water and hydrogen in the feed stream. Details of the CO₂ adsorption on the CaO surface at different reaction temperatures and gas atmospheres using in situ DRIFTS and transient isothermal adsorption experiments with mass spectrometry were obtained. Bridged, bicarbonate and unidentate carbonate species were formed under CO₂/H₂O/He gas mixtures at 600 °C with the latter being the most populated. A substantial decrease in the surface concentration of bicarbonate and OH species was observed when the CaO surface was exposed to CO₂/H₂O/H₂/He gas mixtures at 600 °C, result that probes for the inhibiting effect of H₂ on the phenol steam reforming activity. Phenol steam reforming reaction followed by isothermal oxygen titration allowed the measurement of accumulated “carbonaceous” species formed during phenol steam reforming as a function of reaction temperature and short time on stream. An increase in the amount of “carbonaceous” species with reaction time (650–800 °C range) was evidenced, in particular at 800 °C (4.7 vs. 6.7 mg C/g solid after 5 and 20 min on stream, respectively).     

Gasification of charcoal using supercritical CO2 at high pressures

A novel one-shell high temperature and high pressure semi-continuous reactor has been developed for the study of the Boudouard reaction at temperatures up to 820 °C and pressures up to 32.5 MPa. Semicontinuous gasification of charcoal using supercritical CO₂ has been achieved at conversions up to 90.8% (w/w) at LSHV between 20 and 30 h⁻¹ after 5–9 h. A gasification model is proposed and validated. Effective rates of gasification (1.32 ± 0.12) × 10⁻⁶ to (6.10 ± 2.03) × 10⁻⁵ s⁻¹ were obtained. The results indicated that this method is technically feasible for the on-line production of high pressures streams of CO/CO₂ in the lab for carrying out further chemistries, avoiding the use of CO high pressure bottles.     

Solid acidities of SiO2–TiO2/montmorillonite composites synthesized under different pH conditions

SiO₂–TiO₂/montmorillonite composites were prepared under acidic, neutral and basic conditions and the solid acidity of the resulting composites were determined. All the SiO₂/TiO₂ ratio of the colloidal particles was set at 10 but the resulting SiO₂/TiO₂ ratios were significantly richer in TiO₂. The XRD patterns of the acidic composite showed expanding and broadening of the (001) reflection by intercalation of colloidal SiO₂–TiO₂ particles, but the neutral and basic composites showed only broadening of the reflections and no intercalation. The specific surface areas of the acidic, neutral and basic composites (375, 237 and 247 m²/g, respectively) were much larger than of montmorillonite (6 m²/g). The average pore sizes were about 4, 15 and 50 nm, and the amounts of solid acidic sites measured by the NH₃-TPD were 178, 95 and 86 µmol/g for the acidic, neutral and basic composites, respectively. The solid acid amount of the acidic composite was twice that of a commercial catalyst, K-10, (85 µmol/g) and much higher than the guest phase SiO₂–TiO₂ gel (16 µmol/g) or the host phase montmorillonite (6 µmol/g). The TPD peak temperatures reflect the acid strength, and were similar in all the samples, ranging from 175° to 200 °C.     

Dielectric properties and microstructures of CaSiO3 ceramics with B2O3 addition

The effects of B₂O₃ additives on the sintering behavior, microstructure and dielectric properties of CaSiO₃ ceramics have been investigated. The B₂O₃ addition resulted in the emergence of CaO–B₂O₃–SiO₂ glass phase, which was advantageous to lower the synthesis temperature of CaSiO₃ crystal phase, and could effectively lower the densification temperature of CaSiO₃ ceramic to as low as 1100 °C. The 6 wt% B₂O₃-doped CaSiO₃ ceramic sintered at 1100 °C possessed good dielectric properties: _r = 6.84 and tan δ = 6.9 × 10⁻⁴ (1 MHz).     

Direct formation of H2O2 from H2 and O2 and decomposition/hydrogenation of H2O2 in aqueous acidic reaction medium over halide-containing Pd/SiO2 catalytic system

Formation of H₂O₂ from H₂ and O₂ and decomposition/hydrogenation of H₂O₂ have been studied in aqueous acidic medium over Pd/SiO₂ catalyst in presence of different halide ions (viz. F⁻, Cl⁻ and Br⁻). The halide ions were introduced in the catalytic system via incorporating them in the catalyst or by adding into the reaction medium. The nature of the halide ions present in the catalytic system showed profound influence on the H₂O₂ formation selectivity in the H₂ to H₂O₂ oxidation over the catalyst. The H₂O₂ destruction via catalytic decomposition and by hydrogenation (in presence of hydrogen) was also found to be strongly dependent upon the nature of the halide ions present in the catalytic system. Among the different halides, Br⁻ was found to selectivity promote the conversion of H₂ to H₂O₂ by significantly reducing the H₂O₂ decomposition and hydrogenation over the catalyst. The other halides, on the other hand, showed a negative influence on the H₂O₂ formation by promoting the H₂ combustion to water and/or by increasing the rate of decomposition/hydrogenation of H₂O₂ over the catalyst. An optimum concentration of Br⁻ ions in the reaction medium or in the catalyst was found to be crucial for obtaining the higher H₂O₂ yield in the direct synthesis.     

Nano-gold supported on Fe2O3: A highly active catalyst for low temperature oxidative destruction of methane green house gas from exhaust/waste gases

A number of nano-gold catalysts were prepared by depositing gold on different metal oxides (viz. Fe₂O₃, Al₂O₃, Co₃O₄, MnO₂, CeO₂, MgO, Ga₂O₃ and TiO₂), using the homogeneous deposition precipitation (HDP) technique. The catalysts were evaluated for their performance in the combustion of methane (1 mol% in air) at different temperatures (300–600 °C) for a GHSV of 51,000 h⁻¹. The supported nano-gold catalysts have been characterized for their gold loading (by ICP) and gold particle size (by TEM/HRTEM or XRD peak broadening). Among these nano-gold catalysts, the Au/Fe₂O₃ (Au loading = 6.1% and Au particle size = 8.5 nm) showed excellent performance. For this catalyst, temperature required for half the methane combustion was 387 °C, which is lower than that required for Pd(1%)/Al₂O₃ (400 °C) and Pt(1%)/Al₂O₃ (500 °C) under identical conditions. A detailed investigation on the influence of space velocity (GHSV = 10,000–100,000 cm³ g⁻¹ h⁻¹) at different temperatures (200–600 °C) on the oxidative destruction of methane over the Au/Fe₂O₃ catalyst has also been carried out. The Au/Fe₂O₃ catalyst prepared by the HDP method showed much higher methane combustion activity than that prepared by the conventional deposition precipitation (DP) method. The XPS analysis showed the presence of Au in the different oxidation states (Au⁰, Au¹⁺ and Au³⁺) in the catalyst.     

Kinetic behaviour of HC-SCR over Ag/alumina catalyst using a model paraffinic second generation biodiesel compound

The effect of longer paraffins on the mechanism of the HC-SCR reaction over a 1.91 wt.% Ag/alumina catalyst was investigated by kinetic studies. Hexadecane (C₁₆H₃₄) was chosen as a model compound as it is also a representative molecule for a second generation biodiesel consisting of only long-chain paraffins. The kinetic behaviour of the catalytic reduction of NO_x was examined at steady-state conditions in the temperature range 250–550 °C (50 °C ramping) and by using the following gas concentrations: P_NO = 100, 250, 500, 750 or 1000 ppm, P_hexadecane = 31, 94, 188, 281 or 375 ppm and P_O2=1.5, 3, 4.5, 6 or 9 vol.%. Results showed that in the temperature range 250–425 °C high hexadecane concentration had an inhibiting effect on the NO reduction. At temperatures above 350 °C the apparent reaction orders for hexadecane with respect to hexadecane increased to close or above 1. Reaction orders towards NO were close to 0.55 indicating that NO adsorption on the catalyst surface is stronger than hexadecane adsorption. Based on the experimental data it is proposed that small clusters alone cannot be the active sites for HC-SCR over Ag/Al₂O₃ but the important requirement for high activity over the catalyst is the local concentrations of hydrocarbon and NO on the interface of silver and the support.     

Effect of strontium and cerium doping on the structural characteristics and catalytic activity for C3H6 combustion of perovskite LaCrO3prepared by sol–gel

Two series of Sr- or Ce-doped La_1−xM_xCrO₃ (x = 0.0, 0.1, 0.2 and 0.3) catalysts were prepared by thermal decomposition of amorphous citrate precursors followed by annealing at 800 °C in air atmosphere. The effect of Ce and Sr on the morphological/structural properties of LaCrO₃ was investigated by means of thermogravimetric/differential thermal analysis (TG/DTA) of the precursors decomposition under air, X-ray diffraction (XRD), electron paramagnetic resonance (EPR), transmission electron microscopy–X-ray energy dispersive spectroscopy (TEM–XEDS), S_BET determination, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) techniques. The characterization results are employed to explain catalytic activity results for C₃H₆ combustion. It is shown that the lanthanum chromite perovskite structure is obtained upon thermal treatment of the sol–gel derived precursors at T > ca. 800 °C. The presence of the dopant generally induces the formation of segregated oxide phases in the samples calcined at 800 °C although some introduction of the Sr in the perovskite structure is inferred from EPR measurements. The oxidation activity becomes maximised upon formation of such doped perovskite structure.     

Oxyfluoride glass-silica ceramic composite for low temperature co-fired ceramics

Glass/ceramic composite materials based on CaF₂–AlF₃–SiO₂ oxyfluoride glass and silica ceramic filler were prepared. The sintering behavior, phase composition and dielectric property of oxyfluoride glass/silica ceramic composites, as well as its compatibility with Ag electrode, were investigated. The results show that the glass/ceramic composite system can be sintered at 825 °C. When the amount of SiO₂ increased from 0 to 20 wt.%, the shrinkage decreased from 17.0 to 14.5%, and the dielectric constant decreased from 5.9 to 5.4, while the thermal expansion coefficient (20–200 °C) increased from 6.0 to 10.1 ppm/°C. The sintered samples had low dielectric losses less than 0.002 and high flexural strengths. This novel glass/ceramic composite system exhibits good sintering compatibility with silver paste, which makes it a promising candidate for low temperature co-fired ceramic application.     

Structure and performance of a novel TiO2-phosphonate composite photocatalyst

An innovative SiO₂-PO₄³⁻-TiO₂ photocatalyst is presented which is able to bond TiO₂ to Raschig rings (RR). Evidence for the formation on the catalyst surface of PO stretching bands near 1200–1250 cm⁻¹ is presented by FTIR spectroscopy. The TiO₂ Degussa P25 on the catalyst surface (RR) was further characterized by high-resolution transmission electron microscopy (HRTEM), and X-ray diffraction showing that the composite catalyst prepared at 500 °C does not alter the particle size or crystallographic composition of the TiO₂ Degussa P25 particles. The Ti- and P-distribution of the catalyst surface overlayers was obtained by Ar-sputtering eroding up to 100 topmost catalyst layers. By atomic force microscopy (AFM) the root mean square roughness (Rq) or rugosity of 771 nm and an average height of the catalyst layer of 1.52 μm were found on the glass surface. The root mean square roughness Rq varies very little in value before and after the photocatalysis indicating that the sample porosity is conserved during 4-CP photodegradation. The disappearance kinetics of 4-chlorophenol (4-CP) on the SiO₂-PO₄³⁻-TiO₂ composite occurred within 15 min and was faster than the 45 min needed with suspensions of TiO₂ Degussa P25 (1 g L⁻¹). The SiO₂-PO₄³⁻-TiO₂ photocatalyst was able to degrade repetitively 4-CP solutions without loss of activity. The effect of the light intensity, oxidant concentration and 4-CP concentration on the photodegradation kinetics was investigated and is reported in this study.     

Novel promoting effect of SO2 on the selective catalytic reduction of NOx by ammonia over Co3O4 catalyst

Spinel nano-Co₃O₄ was prepared by solid-state reaction at room temperature and investigated for selective catalytic reduction of NO_x by NH₃ (NH₃-SCR). Although suffering from pore filling and plugging, treatment of this catalyst by SO₂ showed novel promoting effect on NH₃-SCR above 250 °C. Bulk cobalt sulfate was observed over the sulfated Co₃O₄ with XRD, which would be an active component for NH₃-SCR. The sulphated Co₃O₄ catalyst exhibited good resistance to SO₂ (500 ppm, 100 ppm) and 10% H₂O at a space velocity of about 25 000 h⁻¹ at 300 °C, as tested for 12 h.     

Impact of supercritical drying and heat treatment on physical properties of titania/silica aerogel monolithic and its applications

TiO₂–SiO₂ monolithic aerogels were homogeneously prepared using sol–gel method. Critical point of drying of TiO₂–SiO₂ gels with ethanol was studied for 30, 60, 90 and 120 min. Subsequently, the gels were dried with supercritical ethanol, resulting in amorphous aerogels that crystallized following heat treatment at 550 °C from 1 to 5 h. The TiO₂–SiO₂ aerogels were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and surface area measurements. The molar ratio of SiO₂:TiO₂ was 6 and the synthetic strategy revealed that TiO₂–SiO₂ aerogel, had a surface area 868 m²/g, particle size 40 nm, density 0.17 g/cm³ and 80% porosity. The finding indicated that from economic point of view, TiO₂–SiO₂ gel should be supercritical dried for 30 min and heat-treated for 5 h. The TiO₂–SiO₂ aerogel monoliths photocatalyst synthesized using sol–gel method provided insight into the characteristics that make a photocatalyst material well-suited for photodegradation of phenol and cyanide in an industrial waste stream containing Cl⁻, S²⁻ and NH₄⁺. Interestingly, after multiple reuse cycles (i.e. ≥7), photodegradation systems with regenerated photocatalyst showed a slightly decreasing of photoactivity 2–4%. The overall kinetics of photodegradation of either phenol or cyanide using TiO₂–SiO₂ aerogel photocatalyst was found to be of first order.     

An effect of iron(III) oxides crystallinity on their catalytic efficiency and applicability in phenol degradation—A competition between homogeneous and heterogeneous catalysis

Catalytic efficiency, stability and environmental applicability of five iron(III) oxide nanopowders differing in surface area and crystallinity were tested in degradation of concentrated phenolic aqueous solutions (100 g/L) at mild temperature (30 °C), initially almost neutral pH and equimolar ratio of hydrogen peroxide and phenol. The catalyst properties were easily controlled by varying in reaction time during isothermal treatment of ferrous oxalate dihydrate in air at 175 °C. Although the catalytic efficiency clearly increases with the surface area of the nanopowders, it is not due to the solely heterogeneous catalytic mechanism as would be expected. The amorphous Fe₂O₃ nanopowders possessing the largest surface areas (401 m² g⁻¹, 386 m² g⁻¹) are the most efficient catalysts evidently due to their highest susceptibility to leaching in acidic environment arising as a consequence of phenol degradation products. Thus, these amorphous samples act partially as homogeneous catalysts, which was confirmed by a high concentration of leached Fe(III) ions in the solution (19 ppm). The crystalline hematite (α-Fe₂O₃) samples, varying in surface area between 337 m² g⁻¹ and 245 m² g⁻¹, are generally less efficient when compared to the amorphous powders, however their catalytic action is almost exclusively heterogeneous as only 3 ppm of leached Fe(III) was found in the reaction systems catalyzed by nanohematite samples. A significant difference in relative contributions of heterogeneous and homogenous catalysis was definitely established in buffered reaction systems catalyzed by amorphous Fe₂O₃ and nanocrystalline hematite. The nanohematite sample exhibiting the highest heterogeneous action was tested at decreased initial phenol concentration (10 g/L), which is closer to the real contents of phenol in waste waters, and at different hydrogen peroxide/phenol molar ratios to consider its environmental applicability. At the hydrogen peroxide/phenol ratio equal to 5, no traces of the leached iron were detected and the phenol conversion of 84% was reached. Moreover, such a high degree of conversion is accompanied by a decrease of the chemical oxygen demand (COD) from the initial value of 11.23 g/L to 4.22 g/L after 125 min. This fact indicates that the considerable fraction of primary reaction products was totally degraded.     

Electrodeposition of silver from the system AgNO3—ethyleneglycol—water. Effect of temperature ( −30°C) on the smoothness of silver deposits

The electrodeposition of silver from a nitrate bath can be improved by lowering the temperature and by the addition of ethyleneglycol as anti-freeze. When the bath temperature is lowered below 0°C, the dendritic silver deposition is suppressed and a smooth surface is obtained; at −30°C a very finegrained deposit results. The dendritic growth is supposedly prohibited partly by the lowering of temperature and to a less extent by the adsorption of ethyleneglycol at the surface both of which might enhance the activation overvoltage of silver deposition. From the polarisation measurement in, 0·25 M AgNO₃ electrolytes, the exchange current density of Ag deposition was evaluated as 1·70 × 10⁻² A/cm²(25°C) and with 50 vol. per cent ethyleneglycol, 9·72 × 10⁻⁴ A/cm² (25°C) and 1·22 × 10⁻⁵ A/cm² (−32°C). Adsorption of ethyleneglycol on Ag cathode was discussed by differential capacitance change.     

Catalytic reduction of NH4NO3 by NO: Effects of solid acids and implications for low temperature DeNOx processes

Ammonium nitrate is thermally stable below 250 °C and could potentially deactivate low temperature NO_x reduction catalysts by blocking active sites. It is shown that NO reduces neat NH₄NO₃ above its 170 °C melting point, while acidic solids catalyze this reaction even at temperatures below 100 °C. NO₂, a product of the reduction, can dimerize and then dissociate in molten NH₄NO₃ to NO⁺ + NO₃⁻, and may be stabilized within the melt as either an adduct or as HNO₂ formed from the hydrolysis of NO⁺ or N₂O₄. The other product of reduction, NH₄NO₂, readily decomposes at ≤100 °C to N₂ and H₂O, the desired end products of DeNO_x catalysis. A mechanism for the acid catalyzed reduction of NH₄NO₃ by NO is proposed, with HNO₃ as an intermediate. These findings indicate that the use of acidic catalysts or promoters in DeNO_x systems could help mitigate catalyst deactivation at low operating temperatures (<150 °C).     

Synthesis of nano-crystalline Ce0.9Gd0.1O1.95 electrolyte by novel sol–gel thermolysis process for IT-SOFCs

In the present work, nano-crystalline Ce_0.9Gd_0.1O_1.95 (GDC) powder has been successfully prepared by a novel sol–gel thermolysis method using a unique combination of urea and PVA. The gel precursor obtained during the process was calcined at 400 and 600 °C for 2 h. A range of analyzing techniques including XRD, TGA, BET, SEM, EDS and TEM were employed to characterize the physical and chemical properties of obtained powders. GDC gel precursors calcined at 400 and 600 °C were found to have an average crystallite size of 10 and 19 nm, respectively. From the result of XRD patterns, we found that well-crystalline cubic fluorite structure GDC was obtained by calcining the precursor gel at 400 and 600 °C. It has been also found that the sintered samples with lower temperature calcined powder showed better sinterability as well as higher ionic conductivity of 2.21 × 10⁻² S cm⁻¹ at 700 °C in air.     

The role of particle size on the electrochemical properties at 25 and at 55 °C of the LiCr0.2Ni0.4Mn1.4O4 spinel as 5 V-cathode materials for lithium-ion batteries

The role of the particle size on the electrochemical properties at 25 and at 55 °C of the LiCr_0.2Ni_0.4Mn_1.4O₄ spinel synthesized by combustion method has been determined. Samples with different particle size were obtained by heating the raw spinel from 700 to 1100 °C, for 1 h in air. X-ray diffraction patterns revealed that all the prepared materials are single-phase spinels. The main effect of the thermal treatment is the remarkable increase of the particles size from 60 to 3000 nm as determined by transmission electron microscopy. The electrochemical properties were determined at high discharge currents (1C rate) in two-electrode Li-cells. At 25 and at 55 °C, in spite of the great differences in particle size, the discharge capacity drained by all samples is similar (Q_dch ≈ 135 mAh g⁻¹). Instead, the cycling performances strongly change with the particle size. The spinels with Φ > 500 nm show better cycling stability at 25 and at 55 °C than those with Φ < 500 nm. The samples heated at 1000 and 1100 °C, with high potential (E ≈ 4.7 V), elevate capacity (Q ≈ 135 mAh g⁻¹), and remarkable cycling performances (capacity retention after 250 cycles >96%) are very attractive materials as 5V-cathodes for high-energy Li-ion batteries.     

Enhancement of oxygen storage capacity by reductive treatment of Al2O3 and CeO2–ZrO2 solid solution nanocomposite

Oxygen storage capacity (OSC) of CeO₂–ZrO₂ solid solution, Ce_xZr_(1−x)O₄, is one of the most contributing factors to control the performance of an automotive catalyst. To improve the OSC, heat treatments were employed on a nanoscaled composite of Al₂O₃ and CeZrO₄ (ACZ). Reductive treatments from 700 to 1000 °C significantly improved the complete oxygen storage capacity (OSC-c) of ACZ. In particular, the OSC-c measured at 300 °C reached the theoretical maximum with a sufficient specific surface area (SSA) (35 m²/g) after reductive treatment at 1000 °C. The introduced Al₂O₃ facilitated the regular rearrangement of Ce and Zr ions in CeZrO₄ as well as helped in maintaining the sufficient SSA. Reductive treatments also enhanced the oxygen release rate (OSC-r); however, the OSC-r variation against the evaluation temperature and the reduction temperature differed from that of OSC-c. OSC-r measured below 200 °C reached its maximum against the reduction temperature at 800 °C, while those evaluated at 300 °C increased with the reduction temperature in the same manner as OSC-c.     

Effect of sintering temperature on varistor properties and aging characteristics of ZnO–V2O5–MnO2 ceramics

The microstructure, electrical properties, dielectric characteristics, and DC accelerated aging behavior of the ZVM-based varistors were investigated for different sintering temperatures of 800–950 °C. The microstructure of the ZVM-based ceramics consisted of mainly ZnO grain and secondary phase Zn₃(VO₄)₂, which acts as liquid-phase sintering aid. The Zn₃(VO₄)₂ has a significant effect on the sintered density, in the light of an experimental fact, which the decreases of the Zn₃(VO₄)₂ distribution with increasing sintering temperature resulted in the low sintered density. The breakdown field exhibited the highest value (17,640 V/cm) at 800 °C in the sintering temperature and the lowest value (992 V/cm) at 900 °C in the sintering temperature. The nonlinear coefficient exhibited the highest value, reaching 38 at 800 °C and the lowest value, reaching 17 at 850 °C. The varistor sintered at 900 °C exhibited not only high nonlinearity with 27.2 in nonlinear coefficient, but also the highest stability, in which %ΔE_1 mA = −0.6%, %Δα = −26.1%, and %Δ tan δ = +21.8% for DC accelerated aging stress of 0.85 E_1 mA/85 °C/24 h.