可模锻钛合金强度高抗蚀性好

美国ATI华昌公司制成了强度与Ti-6Al-4V相当，且可热加工、冷加工的钛合金。这种被称为ATI425合金的成分为Ti-4Al-2．5V-1-5Fe-0．250，其最重要的特点是易于制造和成形。测试表明，这种合金比Ti-6Ak-4V易于制造。     

增材制造Ti-6Al-4V合金组织调控研究现状

增材制造技术可实现复杂钛合金零件的快速成形,制造的Ti-6Al-4V合金具有较高的强度以及优异的高温性能,被广泛应用于航空、医疗等各大领域。综述了金属增材制造的典型工艺,分析了Ti-6Al-4V合金的相变特征,总结了选区激光熔化制造Ti-6Al-4V的力学性能和组织调控方法,着重分析了热处理温度、冷却速率、变质处理以及超声冲击等对合金组织的影响;展望了增材制造Ti-6Al-4V合金的主要发展方向。     

Ti-6Al-4V钛合金的疲劳裂纹扩展规律

针对熔模铸造Ti-6Al-4V钛合金的等幅疲劳裂纹扩展速率和疲劳裂纹扩展门槛值进行了研究。结果表明：该钛合金CT试样的疲劳裂纹扩展门槛值高于CCT试样的疲劳裂纹扩展门槛值,同一类试样的疲劳裂纹扩展门槛值随着应力比的增加呈下降趋势;疲劳裂纹扩展速率随着平均应力的增加以及应力水平的增加而增大;根据疲劳裂纹扩展试验数据拟合了Ti-6Al-4V钛合金Paris方程和Walker方程中的相关材料参数,以为材料的使用寿命评估及损伤容限设计提供参考。     

Ti及Ti-6Al-4V的水基凝胶注模成形研究

将凝胶注模工艺应用于金属Ti及Ti-6Al-4V合金粉末的坯体成形,研究了高固相含量的Ti粉和Ti-6Al-4V合金粉末的料浆的制备.结果表明,用凝胶注模工艺制备出了固相含量为54ψ%的钛合金粉末料浆和形状复杂的坯体;粉末的颗粒形状是影响料浆固相含量的重要因素,球形粉末配制成的浆料固相含量最高,近球形次之,片状最低;分散剂柠檬酸铵也可以显著提高浆料的固相含量.     

损伤容限钛合金的研究进展及应用现状

本文综述了Ti-6Al-4V ELI, TC4-DT, TC21和TA15 ELI四种损伤容限钛合金的研究新进展及其应用.指出Ti-6Al-4V ELI损伤容限合金在国外已经成功应用于飞机制造中,而 TC4-DT, TC21, TA15 ELI三种损伤容限钛合金在国内处于开发研究阶段.重点介绍了TC4-DT, TC21, TA15 ELI的断裂韧性、疲劳裂纹扩展速率等损伤容限性能及其影响因素,指出片层组织有利于损伤容限性能的提高.     

Ti-6Al-4V合金基体等离子喷涂生物活性羟基磷灰涂层的研究进展

系统阐述了在钛合金(Ti-6Al-4V)表面等离子喷涂羟基磷灰石(HA)涂层的研究进展.描述了等离子喷涂制备HA涂层的工艺过程、微观形貌和化学组成.综述几种综合性能较高的复合型涂层:HA/BG(生物活性玻璃)复合涂层,HA/ZrO2复合增强型涂层,HA/Ti涂层,HA/Ti-6Al-4V梯度涂层;并对HA涂层发展趋势进行了展望.     

航空工业钛合金紧固件失效分析研究进展

分析了航空工业钛合金紧固件的受力条件,综述了国内外学者关于钛合金紧固件失效形式及影响因素的相关研究,详细介绍了氢含量、加工过程、热处理、金属头部流线、装配过程等影响因素,总结出在生产制造过程与装配过程中,进一步提高钛合金紧固件使用性能的工艺手段与措施.     

钛合金管件高压气胀成形工艺研究进展

高压气胀成形是在内高压成形基础上发展起来的管件成形技术,采用气体介质加载,可在高温下成形钛合金构件。以Ti-3Al-2.5V钛合金管材为实验材料,开展了矩形截面构件和大截面差构件高压气胀成形工艺研究,提出了气压阶梯加载方法和气压与轴向位移匹配的加载方法。结果表明,利用Ti-3Al-2.5V钛合金在一定温度和应变速率范围的应变和应变速率双硬化机制,采用合理的加载路径,能够消除开裂缺陷,以较高的效率实现钛合金异形管件的成形制造,并且构件壁厚相对均匀,形状和组织性能均可得到有效控制。     

钛合金在大型运输机上的应用

随着航空业的复苏,大型运输机的需求量日益增多.钛合金在大型运输机上的用量不断扩大,B787客机和C-17军用运输机的钛合金用量已分别达15%和10.3%.B777使用了Ti-10V-2Fe-3Al合金主起落架载重梁,B747使用了Ti-6Al-4V合金主起落架梁、A380和A350使用了全钛挂架.钛合金在大型运输机上的应用出现亮点是使用了钛合金整体精铸件、钛合金薄璧铸件、石墨纤维钛合金层板、新型高强高韧近β钛合金.文章最后指出我国航空界和材料界应充分重视相关钛合金材料及其热加工工艺研究开发和应用工作,不断提高使用性能,降低生产成本,以满足大型运输机的发展需求.     

TI-6Al-4V合金置氢-除氢组织与力学性能

为研究除氢处理对置氢钛合金组织与性能的影响,对Ti-6Al-4V合金在不同参数条件下进行了置氢与除氢处理,采用光学显微镜分析了置氢-除氢处理过程中Ti-6Al-4V合金微观组织的演化规律,通过室温拉伸试验研究了置氢-除氢处理后Ti-6Al-4V合金的力学性能,探讨了Ti-6Al-4V合金置氢-除氢组织与力学性能之间的相...     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.