Electrodeposition of silver from the system AgNO3—ethyleneglycol—water. Effect of temperature ( −30°C) on the smoothness of silver deposits

The electrodeposition of silver from a nitrate bath can be improved by lowering the temperature and by the addition of ethyleneglycol as anti-freeze. When the bath temperature is lowered below 0°C, the dendritic silver deposition is suppressed and a smooth surface is obtained; at −30°C a very finegrained deposit results. The dendritic growth is supposedly prohibited partly by the lowering of temperature and to a less extent by the adsorption of ethyleneglycol at the surface both of which might enhance the activation overvoltage of silver deposition. From the polarisation measurement in, 0·25 M AgNO₃ electrolytes, the exchange current density of Ag deposition was evaluated as 1·70 × 10⁻² A/cm²(25°C) and with 50 vol. per cent ethyleneglycol, 9·72 × 10⁻⁴ A/cm² (25°C) and 1·22 × 10⁻⁵ A/cm² (−32°C). Adsorption of ethyleneglycol on Ag cathode was discussed by differential capacitance change.     

A comparison of diamonds irradiated by high fluence neutrons or electrons, before and after annealing

Neutron- and electron-irradiated type Ia “black” diamonds were analyzed: three near colorless type Ia diamonds were treated in a nuclear reactor with a dose of 1.8 × 10¹⁷ neutrons/cm² and three equivalent samples were irradiated in an electron accelerator with a dose of approximately 0.5 GGy 10 MeV electrons. The diamonds were then annealed and analyzed after the different steps of the treatment. The samples turned from near colorless to very dark green to opaque black upon irradiation and deep greenish yellow to deep orangy brown upon annealing (Fig. 1). The amount of brown color developed during the treatment was found to relate to the type of irradiation used and likely to the total dose of irradiation. The absorption and photoluminescence features as well as the color changes that were observed were found to be unusual and characteristic for diamonds treated with such high irradiation doses. Certain spectral features such as the 644/649 nm, the 724/734/738 nm, the 920 nm and the 967 nm absorptions were only detected in the neutron-irradiated diamonds while others such as the 6165 cm^− 1 and the 805 nm absorptions were only found in the spectra of the electron-irradiated stones.In addition to these treatment experiments some neutron-irradiated very dark green (appearing black) diamonds were heated from 300 to 1100 °C in increments of 50 °C to get a precise idea of the temperature at which color changes occur and the various absorption peaks form. All diamonds turned yellowish to orangy brown after annealing above 700 °C and most of them exhibited unusually strong H1b and/or H1c absorptions after annealing at > 900 °C.     

Gasification of charcoal using supercritical CO2 at high pressures

A novel one-shell high temperature and high pressure semi-continuous reactor has been developed for the study of the Boudouard reaction at temperatures up to 820 °C and pressures up to 32.5 MPa. Semicontinuous gasification of charcoal using supercritical CO₂ has been achieved at conversions up to 90.8% (w/w) at LSHV between 20 and 30 h⁻¹ after 5–9 h. A gasification model is proposed and validated. Effective rates of gasification (1.32 ± 0.12) × 10⁻⁶ to (6.10 ± 2.03) × 10⁻⁵ s⁻¹ were obtained. The results indicated that this method is technically feasible for the on-line production of high pressures streams of CO/CO₂ in the lab for carrying out further chemistries, avoiding the use of CO high pressure bottles.     

Enhanced performance of HFCVD nanocrystalline diamond self-mated tribosystems by plasma pretreatments on silicon nitride substrates

Nanocrystalline diamond (NCD) coatings were grown by the hot-filament chemical vapour deposition (HFCVD) method on hydrogen plasma pretreated silicon nitride (Si₃N₄) substrates. The friction and wear behaviour of self-mated NCD films, submitted to unlubricated sliding and high applied loads (up to 90 N), was assessed using an oscillating ball-on-flat configuration in ambient atmosphere. The reciprocating tests revealed an initially high friction coefficient peak, associated to the starting surface roughness of NCD coatings (R_q = 50 nm). Subsequently, a steady-state regime with low friction coefficient values (0.01–0.04) sets in, related to a smoother (R_q = 17 nm) tribologically modified surface. A polishing wear mechanism governing the material loss was responsible for mild wear coefficients (k  10^− 7 mm³ N^− 1 m^− 1). The hydrogen etching procedure notably increased the film adhesion with respect to untreated surfaces as demonstrated by the high threshold loads (60 N; 3.5 GPa) prior to film delamination.     

Oxygen diffusion into polystyrene–bentonite films

A simple fluorescence technique is proposed for the measurement of the diffusion coefficient of oxygen into polystyrene–clay composite films. The composite films were prepared from the mixture of surfactant-free pyrene (P)-labeled polystyrene latexes (PS) and modified bentonite (MNaLB) at various compositions at room temperature. These films were annealed at 200 °C above the glass transition (T_g) temperature of polystyrene for 10 min. Oxygen diffusion into the films was monitored with steady state fluorescence (SSF) measurements. Measurements were performed at room temperature for different film compositions (0, 5, 10, 20, 30, 50 and 60 mass% modified bentonite) films to evaluate the effect of MNaLB content on oxygen diffusion. The diffusion coefficient, D of oxygen was determined by the fluorescence quenching method by assuming Fickian transport and increased from 7.4 × 10^− 10 to 26.9 × 10^− 10 cm² s^− 1 with increasing MNaLB content. This increase in D value was explained by formation of microvoids in the film. These voids are large enough to contribute to the penetration of oxygen molecules through the films. The montmorillonite content did not affect the quenching rate constant, k_q and mutual diffusion coefficient, D_m values.     

Characterization of smectite after acid activation with microwave irradiation

The effect of acid activation under microwave (MW) irradiation on the textural and structural properties of a smectite from Maghnia (Algeria) was investigated.Sample aliquots were treated with 2 M hydrochloric acid for various times under variable irradiation power. The influence of activation parameters (MW power and time duration) on the textural and structural properties of the activated samples (crystallinity, specific surface area, pore volume, pore diameter, porosity, pore size distribution and morphology) have been studied.The prepared materials were characterized by X-ray diffraction, Differential Thermal and Thermo Gravimetric Analysis (DTA and TGA), Scanning Electron Microscopy (SEM) and nitrogen adsorption/desorption to obtain information about their structure and surface texture.The treated samples consisted of microporous and mesoporous structures. The specific surface area, pore diameter and pore volume of an adsorbent prepared by the microwave-heating method were 165.80 m²/g, 50 nm and 0.1919 cm³/g, respectively. The pore volumes of mesopores and micropores were 163.90 · 10^− 3 and 28.89 · 10^− 3 cm³/g, respectively. Furthermore, small pores were created in the prepared materials with microwave irradiation.     

DI-B experiment: planning, design and performance of an in situ diffusion experiment in the Opalinus Clay formation

The DI-B experiment is a long-term, natural-scale, in situ diffusion experiment, which is being performed in the Opalinus Clay formation at the Mont Terri Underground Rock Laboratory (URL), in Switzerland, employing nonradioactive tracers. One of the key aspects to be addressed for nuclear waste repository safety assessment purposes is the understanding of the transport mechanisms of the radionuclides contained in the radioactive waste. Consolidated clay formations display very low water hydraulic conductivities, so it is expected that the predominant transport process will be diffusion.The experimental set-up has been designed to withstand the site conditions and for monitoring and recording several physicochemical parameters (pH, conductivity, oxidation–reduction potential), as well as the pressures in the circuit and for the long-distance monitoring of the data acquisition system.The tracer selection has been made based on previous investigations carried out at CIEMAT, including a literature survey, laboratory sorption experiments and hydrogeochemical modeling for determining tracer stability under the physicochemical conditions to be expected in the site. The final selection includes ⁶Li, ⁸⁷Rb, D (as D₂O) and I (as I⁻). Hydrogeochemical modeling confirmed the stability of all the tracers selected. Batch sorption experiments showed that no sorption in the rock occurred in the case of ⁶Li, D and I (conservative tracers), whereas ⁸⁷Rb was 100% sorbed. However, ⁸⁷Rb was chosen because of its analogy with Cs, a relevant radionuclide commonly present in the nuclear spent fuel.Diffusion experiments have been carried out at laboratory scale with Opalinus Clay samples to provide diffusion parameters for modeling purposes. Effective diffusion coefficients, perpendicular and parallel to the bedding planes of the rock, respectively, were (1.68± 0.42)×10⁻¹¹ and (4.02± 0.30)×10⁻¹¹ m²/s for tritium, and (2.70± 0.27)×10⁻¹² and (1.38± 0.49)×10⁻¹¹ m²/s for iodide. Additional through-diffusion experiments (parallel to the bedding) were performed with the nonsorbing tracer ³⁶Cl⁻, in order to check the results obtained for iodide. The effective diffusion coefficient measured for chloride ions was (1.18± 0.27)×10⁻¹¹ m²/s, which is practically equal to the value obtained for iodide.Preliminary diffusion calculations have been carried out using two transport codes: GIMRT and CORE^2D, with conservative and nonconservative tracers, using effective diffusion coefficients (D_e) obtained experimentally in the laboratory (through-diffusion experiments) or selected from the literature. The diffusion profiles obtained from the calculations showed slight variations, which were consistent with the different modeling approaches employed. The predictive modeling results have been used to determine the initial tracer concentration that should be added to the circuit to assure well-defined profiles at the end of the experiment.This long-term in situ diffusion experiment will also provide useful data for the interpretation of previous diffusion experiments performed at the Mont Terri URL.     

Growth rate improvements in the hot-filament CVD deposition of nanocrystalline diamond

The hot-filament CVD, a less used technique for NCD films growth using Ar/H₂/CH₄ gas mixtures, is optimized for the coating of silicon nitride ceramics. Parameters such as gas composition (Ar/H₂ and CH₄/H₂ ratios), total gas pressure, total mass flow and substrate and filament temperatures, are studied to assess their effect on NCD growth kinetics as well as on film quality and morphology. The smallest diamond crystallite sizes (8 nm) were recorded for the slowest growth rate of 0.1 μm h^− 1. A remarkable result is the very high growth rate of 1.6 μm h^− 1 of continuous NCD coatings with 28 nm of crystallite size, obtained in selected deposition conditions.     

Adsorption and binding of the transgenic plant proteins, human serum albumin, β-glucuronidase, and Cry3Bb1, on montmorillonite and kaolinite: Microbial utilization and enzymatic activity of free and clay-bound proteins

Human serum albumin (HSA), β-glucuronidase (GUS), and the Cry3Bb1 protein from Bacillus thuringiensis subsp. kumamotoensis are expressed by genetically-modified plants. Commercial samples of these proteins adsorbed and bound rapidly on the clay minerals, kaolinite (K) and montmorillonite (M). Adsorption increased as the concentration of protein increased and then reached a plateau. The greatest amount of adsorption and binding occurred with the Cry3Bb1 protein, of which there was no desorption: 6.7 ±0.21 μg adsorbed and bound μg^− 1 of M; 2.1 ± 0.39 μg adsorbed and bound μg^− 1 of K. With GUS, 2.2 ± 0.29 μg adsorbed and 1.7 ±0.21 μg bound μg^− 1 of M; 1.5 ± 0.28 μg adsorbed and 1.0 ± 0.03 μg bound μg^− 1 of K. HSA was adsorbed and bound the least: 1.2 ±0.04 μg adsorbed and 0.8 ± 0.05 μg bound μg^− 1 of M; 0.4 ± 0.05 μg adsorbed and 0.4 ± 0.03 μg bound μg^− 1 of K. However, X-ray diffraction analyses indicated that only HSA intercalated M, and none of the proteins intercalated K, a nonswelling clay. When bound, the proteins were not utilized for growth by mixed cultures of soil microorganisms, whereas the cultures readily utilized the free (i.e., not adsorbed or bound) proteins as sources of carbon and energy. The enzymatic activity of GUS was significantly enhanced when bound on the clay minerals. These results indicated that recombinant proteins expressed by transgenic plants could persist and function in soil after release in root exudates and from decaying plant residues as the result of the protection provided against biodegradation by binding on clay minerals.     

Magnetic properties of CNX whiskers

Carbon–nitrogen whiskers have been prepared by pyrolysis of 1,2-diaminopropane at 950 °C or of allylamine at 900 °C followed by quenching. They are scrolls of carbon film typically 250 nm thick and up to 1 mm long with about five layers in a structure like a “cigare russe” or “brandy snap”, about 50 μm in diameter. Approximately 8 wt% of nitrogen is incorporated into the carbon films, which are practically amorphous, exhibiting a broad diffraction peak at d = 0.34 nm. The whiskers are on the border of metallic conductivity with a resistivity of about 10⁻⁶ Ωm, and they may show either a positive or a negative temperature coefficient of resistance. The pyrolysis produces either whiskers, soot or both. Magnetization measurements of the whiskers made from 1,2-diaminopropane reveal a large diamagnetic susceptibility of χ = −170 × 10⁻⁹ m³  kg⁻¹ and a small ferromagnetic component of unknown origin with σ_S of up to 0.2 A m² kg⁻¹, whereas the soot shows a purely diamagnetic signal, with χ ≈ −40 × 10⁻⁹ m³ kg⁻¹.     

Nanodiamond lateral comb array field emission diode for high current applications

Nanodiamond comb-shaped lateral field emitter arrays in diode configuration were fabricated and characterized for high current field emission. Nitrogen-incorporated nanocrystalline diamond with grain size of 5–10 nm was micropatterned using RIE to realize interconnected arrays of comb structures equipped with uniformly spaced high aspect ratio lateral emitter fingers. A 9000-fingered nanodiamond lateral comb array diode with an inter-electrode spacing of 8 μm demonstrated a high emission current of  25 mA at an anode voltage of 260 V (electric field  32 V/μm) in 10^− 7 Torr vacuum. The lateral emitter configuration shows potential for higher power with no emission current saturation observed. These vacuum micro/nanoelectronic devices comprised of nanodiamond lateral field emission diodes are attractive for low-voltage operating high current electron sources, high-power and high-speed switches, and other extreme demand/extreme environment electronics.     

Amorphization and graphitization of single-crystal diamond — A transmission electron microscopy study

The amorphization and graphitization of single-crystal diamond by ion implantation were explored using transmission electron microscopy (TEM). The effect of ion implantation and annealing on the microstructure was studied in (100) diamond substrates Si⁺ implanted at 1 MeV. At a dose of 1 × 10¹⁵ cm^− 2, implants done at 77 K showed a damage layer that evolves into amorphous pockets upon annealing at 1350 °C for 24 h whereas room temperature implants (303 K) recovered to the original defect free state upon annealing. Increasing the dose to 7 × 10¹⁵ Si⁺/cm² at 303 K created an amorphous-carbon layer 570 ± 20 nm thick. Using a buried marker layer, it was possible to determine that the swelling associated with the amorphization process was 150 nm. From this it was calculated that the layer while obviously less dense than crystalline diamond was still 15% more dense than graphite. Electron diffraction is consistent with the as-implanted structure consisting of amorphous carbon. Upon annealing, further swelling occurs, and full graphitization is achieved between 1 and 24 h at 1350 °C as determined by both the density and electron diffraction analysis. No solid phase epitaxial recrystallization of diamond is observed. The graphite showed a preferred crystal orientation with the (002)g//(022)d. Comparison with Monte Carlo simulations suggests the critical displacement threshold for amorphization of diamond is approximately 6 ± 2 × 10²² vacancies/cm³.     

The role of pressure on thin amorphous carbon films deposited using microwave surface wave plasma CVD

We report the effects of gas composition pressure (GCP) on the optical, structural and electrical properties of thin amorphous carbon (a-C) films grown on p-type silicon and quartz substrates by microwave surface wave plasma chemical vapor deposition (MW SWP CVD). The films, deposited at various GCPs ranging from 50 to 110 Pa, were studied by UV/VIS/NIR spectroscopy, atomic force microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and current–voltage characteristics. The optical band gap of the a-C film was tailored to a relatively high range, 2.3–2.6 eV by manipulating GCPs from 50 to 110 Pa. Also, spin density strongly depended on the band gap of the a-C films. Raman spectra showed qualitative structured changes due to sp³/sp² carbon bonding network. The surfaces of the films are found to be very smooth and uniform (RMS roughness < 0.5 nm). The photovoltaic measurements under light illumination (AM 1.5, 100 mW/cm²) show that short-circuit current density, open-circuit voltage, fill factor and photo-conversion efficiency of the film deposited at 50 Pa were 6.4 μA/cm², 126 mV, 0.164 and 1.4 × 10^− 4% respectively.     

Multi-walled carbon nanotubes (MWCNTs) and room temperature ionic liquids (RTILs) carbon paste Er(III) sensor based on a new derivative of dansyl chloride

Solution studies showed the strong interaction of [5-(dimethylamino) naphthalene-1-sulfonyl 4-phenylsemicarbazide] (NSP) with Er(III) ions. NSP was used as a sensing material during construction of carbon paste Er(III) sensors. The electrodes were modified with 1-n-butyl-3-methylimidazolium tetrafluoroborate, [bmim]BF₄, as room temperature ionic liquid (RTIL) and multi-walled carbon nanotube (MWCNT). Potentiometric sensors constructed with [bmim]BF₄ and MWCNTs show better sensitivity, selectivity, response time, and response stability compared to Er(III) carbon paste sensors. The best performance for the modified sensor was obtained with an electrode composition of 20% [bmim]BF₄, 20% NSP, 45% graphite powder and 15% MWCNT. This particular sensor formulation exhibits a Nernstian response (19.8 ± 0.3 mV decade⁻¹) toward Er(III) ions in the range of 1.0 × 10⁻⁷ to 1.0 × 10⁻¹ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. The proposed modified Er(III) sensor can be used over the pH range from 3.5 to 9.0.     

Amperometric detection of hydrogen peroxide at nano-nickel oxide/thionine and celestine blue nanocomposite-modified glassy carbon electrodes

A simple procedure was developed to prepare a glassy carbon (GC) electrode modified with nickel oxide (NiOx) nanoparticles and water-soluble dyes. By immersing the GC/NiOx modified electrode into thionine (TH) or celestine blue (CB) solutions for a short period of time (5–120 s), a thin film of the proposed molecules was immobilized onto the electrode surface. The modified electrodes showed stable and a well-defined redox couples at a wide pH range (2–12), with surface confined characteristics. In comparison to usual methods for the immobilization of dye molecules, such as electropolymerization or adsorption on the surface of preanodized electrodes, the electrochemical reversibility and stability of these modified electrodes have been improved. The surface coverage and heterogeneous electron transfer rate constants (k_s) of thionin and celestin blue immobilized on a NiOx-GC electrode were approximately 3.5 × 10⁻¹⁰ mol cm⁻², 6.12 s⁻¹, 5.9 × 10⁻¹⁰ mol cm⁻² and 6.58 s⁻¹, respectively. The results clearly show the high loading ability of the NiOx nanoparticles and great facilitation of the electron transfer between the immobilized TH, CB and NiOx nanoparticles. The modified electrodes show excellent electrocatalytic activity toward hydrogen peroxide reduction at a reduced overpotential. The catalytic rate constants for hydrogen peroxide reduction at GC/NiOx/CB and GC/NiOx/TH were 7.96 (±0.2) × 10³ M⁻¹ s⁻¹ and 5.5 (±0.2) × 10³ M⁻¹ s⁻¹, respectively. The detection limit, sensitivity and linear concentration range for hydrogen peroxide detection were 1.67 μM, 4.14 nA μM⁻¹ nA μM⁻¹ and 5 μM to 20 mM, and 0.36 μM, 7.62 nA μM⁻¹, and 1 μM to 10 mM for the GC/NiOx/TH and GC/NiOx/CB modified electrodes, respectively. Compared to other modified electrodes, these modified electrodes have many advantages, such as remarkable catalytic activity, good reproducibility, simple preparation procedures and long-term stabilities of signal responses during hydrogen peroxide reduction.     

Synthesis of proton conductive membranes based on inorganic–organic hybrid structure bound with phosphonic acid

Proton conductive inorganic–organic hybrid membranes were synthesized from styrene derivatives of alkoxysilane and ethyl 2-[3-(dihydroxyphosphonyl)-2-oxopropyl] acrylate (EPA) through copolymerization followed by sol–gel reaction. Self-standing, homogeneous and transparent hybrid membranes with chemically bound phosphonic acid groups were synthesized. FT-IR analysis exhibited the hybrid membranes included phosphonic acid groups. ¹³C and ²⁹Si NMR studies indicated that alkoxysilyl functionalized styrene derivatives were not only copolymerized with EPA but also condensed yielding Si–O–Si linkages by sol–gel reaction. TG–DTA analysis revealed that these membranes were thermally stable up to 200 °C in dry O₂. The proton conductivities of the hybrid membranes increased with phosphonic acid content and temperature. The P/Si ratio of the membrane was dependent on the number of alkoxy group in the starting alkoxysilane. The hybrid membrane from (dimethylmethoxysilylmethyl)styrene (DMMSMS(M))/EPA = 1/6 revealed proton conductivities of 6.3 × 10⁻³ and 2.4 × 10⁻⁴ S cm⁻¹ at 68.0% relative humidity and 18.8% relative humidity, respectively, at 140 °C.     

Highly conductive ionic liquid based ternary polymer electrolytes obtained by in situ photopolymerisation

New ternary polymer electrolytes based on a commercial cross-linking resin dianol diacrylate (DDA), tetramethylene sulphone (TMS) as a compatibilizing solvent and ionic liquids (ILs) were prepared by in situ photopolymerisation. The electrolytes containing two polymer-to-TMS-to-IL ratios, 20:30:50 and 20:20:60 by weight, respectively and six various ILs were investigated. The obtained materials were flexible, self-standing with good mechanical properties and a long-term stability. They showed high ionic conductivities, in the range of ca. 7 × 10⁻³ to 3 × 10⁻² S cm⁻¹ at 25 °C. A very important result is that the conductivities of all the prepared polymer electrolytes exceeded the conductivities of the corresponding neat ILs by 2–3.5 times. The temperature dependence of the ionic conductivity correlates with VTF equation. All the materials prepared were characterized by a broad electrochemical stability window (3.3–3.7 V).     

Thermal and mechanical properties of LaNbO4-based ceramics

Thermal and mechanical properties of polycrystalline La_1−xA_xNbO₄ (x = 0, 0.005, 0.02 and A = Ca, Sr and Ba) are reported. The materials possess a ferroelastic to paraelastic phase transition close to 500 °C, and the linear thermal expansion is significantly lower (8.6 ± 0.5 × 10⁻⁶ °C⁻¹) for the paraelastic phase compared to the ferroelastic phase (15 ± 3 × 10⁻⁶ °C⁻¹). The hardness was significantly higher for acceptor doped materials (6 GPa) compared to pure LaNbO₄ (3 GPa) due to a significantly smaller average grain size. The fracture toughness of La_0.98Sr_0.02NbO₄, measured by single edge V-notched beam method, was 1.7 ± 0.2 MPa m^1/2 independent of temperature up to 600 °C. The ferroelastic properties of the materials were confirmed by non-linear relationships between stress and strain during compression/decompression, a remnant strain after decompression and the presence of ferroelastic domains. The mechanical properties of LaNbO₄-based materials are discussed with focus on ferroelasticity, microcracking due to crystallographic anisotropy and pinning of ferroelastic domain boundaries.     

Novel coated graphite electrode for the selective determination of Gd(III) in rocks and waste water samples

A novel gadolinium selective coated graphite electrode based on 2,6-bis-[1-{N-cyanopropyl,N-(2-methylpridyl)}aminoethyl]pyridine [P] is described. The best performance was exhibited by the electrode having membrane composition P:NaTPB:PVC:NPOE as 8:4:30:58 (%, w/w). The electrode demonstrates excellent potentiometric characteristics towards gadolinium ion over several interfering ions. The electrode exhibited a Nernstian response to Gd³⁺ ion over a wide concentration range 2.8 × 10⁻⁷ to 5.0 × 10⁻² M with a detection limit (6.3 ± 0.1) × 10⁻⁸ M and slope 19.6 ± 0.1 mV decade⁻¹ of a_Gd³⁺. Furthermore, it showed a fast response time (12 s) and can be used for 2.5 months without significant divergence in its characteristics. Noticeably, the electrode can tolerate the concentration of different surfactants up to 1.0 × 10⁻⁴ M and can be used successfully in 30% (v/v) ethanol media and 10% (v/v) methanol and acetonitrile water mixture. The useful pH range of this sensor is 2.0 to 8.0. It is sufficiently selective and can be used for the determination of Gd³⁺ ions in waste water and rock samples. It also serves as a good indicator in the potentiometric titration of GdCl₃ with EDTA.     

Electrochemical behavior of Ni(II)/Ni in a hydrophobic amide-type room-temperature ionic liquid

Electrochemical reaction of Ni(II)/Ni was investigated in a hydrophobic room-temperature ionic liquid, 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide (BMPTFSA) containing Ni(TFSA)₂ as a Ni source. The UV–vis spectra showed that Ni(II) in BMPTFSA is octahedrally coordinated with TFSA⁻ anions. The average activation energy for the diffusion coefficients of this Ni(II) complex was 26 kJ mol⁻¹, which was close to that for the viscosity. The diffusion coefficient of Ni(II) was estimated to be 9.3 × 10⁻⁸ cm² s⁻¹. Chronoamperometric measurements showed that the electrodeposition of Ni on a platinum substrate involved three-dimensional instantaneous nucleation under diffusion control at room-temperature. The electrodeposits obtained by galvanostatic electrolysis with the current density of −0.046 mA cm⁻² at 70 and 100 °C were identified as metallic Ni by XRD.