纳米碳管-(Ni-P)复合材料制备及性能

采用化学复合镀的方法,在45#钢衬底上制备纳米碳管(CNTs)-(Ni-P)复合材料。探讨了该复合材料的制备技术及工艺条件,通过对实验结果的观察和分析,确定了制备CNTs-(Ni-P)复合材料的最佳工艺条件。利用透射电镜(TEM)观察纳米碳管的结构;用扫描电镜(SEM)观察纳米碳管形貌及其在复合材料中的分布;利用原子力显微镜(AFM)观察复合材料表面的粗糙度。同时还对纳米碳管复合材料的耐磨性进行了初步的测试。实验结果表明,该复合材料的耐磨性明显好于未镀及单纯镀镍材料。     

纳米碳管/环氧树脂纳米复合材料的研究

采用熔融混合法合成了不同纳米碳管含量的纳米碳管/环氧树脂复合材料,测试了弯曲性能、冲击强度,并利用扫描电镜(TEM)对产物进行了表征,同时,针对纳米碳管对环氧树脂电学性能的影响做了初步研究。结果表明,当纳米碳管含量为0.05%时,纳米碳管/环氧树脂复合材料的冲击强度、弯曲强度最高,弯曲强度提高100%,弯曲模量提高41%,冲击强度提高4倍,纳米碳管在环氧树脂基体中呈单根分散,纳米碳管使环氧树脂的体积电阻下降,导电性增加。     

纳米粒子改性环氧树脂及其复合材料力学性能研究

通过机械共混法制备了Al2O3纳米粒子改性环氧树脂基体,研究了纳米粒子含量对改性树脂基体力学性能的影响,并采用紧凑拉伸实验研究了纳米粒子改性环氧树脂的断裂韧性。利用改性树脂制备了玻璃纤维增强复合材料,研究了改性复合材料的力学性能与纳米粒子含量之间的关系。结果表明:纳米粒子的加入明显改善了环氧树脂基体的断裂韧性并且有助于提高树脂与纤维之间的界面粘接强度,因而使改性复合材料的层间性能明显提高而其他力学性能基本不变。     

纳米陶瓷粉改性环氧树脂研究

使用超声波细胞粉碎机将纳米陶瓷粉按照不同比例添加到环氧树脂体系中,制备了纳米陶瓷粉/环氧树脂复合材料,研究了纳米陶瓷粉对复合材料硬度及力学性能的影响。使用扫描电子显微镜、巴氏硬度仪、万能试验机表征和分析了纳米陶瓷粉/环氧树脂复合材料的断面形貌、硬度及力学性能。结果表明,纳米陶瓷粉对环氧树脂有增强增韧的效果,当纳米陶瓷粉添加量为15%时,复合材料的力学性能提高,硬度增加。     

环氧树脂/纳米ATO复合材料的性能研究

将纳米ATO添加到环氧树脂中,采用超声波分散制备环氧树脂/纳米ATO复合材料,对复合材料的导电性能及物理机械性能进行了测试,并采用扫描电镜对复合材料的断裂形貌进行了分析.实验结果表明:复合材料的电阻率随着ATO含量的增加而减小,当ATO%=8%时,电阻率达到了105Ω·cm;随着纳米碳纤维的加入量的增加,复合材料的拉伸强度呈现一个先增加后减小的趋势,当ATO的质量分数为5%时,复合材料的力学性能最佳.     

环氧树脂/粘土纳米复合材料的制备与性能研究

研究了有机蒙脱土在环氧树脂中的插层和剥离行为,制备了两种环氧树脂/蒙脱土纳米复合材料并测试了其力学性能。实验结果表明,环氧树脂与有机土的相容性好,二者混合时环氧树脂很容易插入到粘土层间。使用经不同有机阳离子处理的两种有机蒙脱土,分别制得插层型和剥离型环氧/粘土纳米复合材料,力学性能结果表明,剥离型纳米复合材料的性能优于同组成的插层型纳米复合材料。     

纳米Al2O3改性环氧树脂复合材料的低温力学性能研究

通过机械搅拌的方法将纳米Al2O3颗粒分散在环氧树脂基体中,用干燥箱对其固化来制备纳米Al2O3,环氧树脂复合材料,然后进行低温冷冻处理,从而对其进行力学性能测验。研究表明环氧树脂在120℃下烘烤12h所取得的固化效果较好;而低温处理后的环氧树脂复合材料具有优于未处理的环氧树脂复合材料的力学性能,尤其是在耐压和韧性方面。     

纳米碳管/羟基磷灰石复合材料的凝胶注模

采用凝胶浇注成型工艺制备了纳米碳管/ 羟基磷灰石复合材料坯体。研究了p H 值、分散剂、固相含量(纳米碳管和羟基磷灰石在料浆中的质量分数) 、分散工艺等因素对料浆和复合材料坯体性能的影响, 对坯体的力学性能进行了测试, 借助扫描电镜分析了坯体的微观组织。实验发现, 料浆的p H 值应控制在10～12 的范围内;聚甲基丙烯酸铵的浓度为0. 6 %时, 羟基磷灰石悬浮体流动性最好; 十二烷基磺酸钠的浓度在SDS/ CNTs = 1 %～2 %时, 纳米碳管/ 羟基磷灰石复相料浆的粘度最低; 采用球磨法制备的复相料浆固相含量达到55 % , 复合材料坯体的抗弯强度达到57. 403 MPa 。      

激光改性纤维对其增强环氧树脂复合材料力学性能的影响

利用激光对玻璃纤维、玄武岩纤维和碳纤维进行表面改性后,以环氧树脂为基体,分别制备三种纤维增强环氧树脂复合材料。利用SEM和万能试验机对表面改性前后的碳纤维形态、力学性能及三种纤维/环氧树脂复合材料的力学性能和断面形貌进行表征,研究了纤维激光表面改性对三种纤维及其增强环氧树脂复合材料力学性能的影响。结果表明:激光表面改性对碳纤维/环氧树脂复合材料的力学性能提升最高,其拉伸强度最大提高了77.06%,冲击强度最大提高了31.25%,玄武岩纤维/环氧树脂复合材料的力学性能提升次之,而玻璃纤维/环氧树脂复合材料的力学性能有所下降。因此,激光进行表面改性适用于碳纤维和玄武岩纤维。     

针状纳米ZnO制备EP/ZnO复合材料及其力学性能的研究

研究了用热镀锌渣作原料制得的针状纳米ZnO对EP/ZnO复合材料力学性能的影响.结果表明:使用具有空间结构的针状纳米ZnO所制备的环氧树脂复合材料,与普通ZnO所制备的环氧树脂复合材料相比力学性能得到了较大的提高和改善.当纳米ZnO的含量为4％(质量分数)时,材料的力学性能得到了明显改善,其冲击强度提高46.9％,抗拉...     

The impact of fluorinated MWCNT additives on the enhanced dynamic mechanical properties of e-beam-cured epoxy

Multi-walled carbon nanotubes were embedded into e-beam-cured epoxy resin to improve the mechanical properties of epoxy resin. The surfaces of these carbon nanotubes were modified using a fluorination treatment to improve their dispersion and adhesion in epoxy resin. The dynamic mechanical properties of epoxy/carbon nanotube composites were investigated at various heating rates and frequencies. As an effect of fluorination treatment, the semi-ionic bond of C–F on the surface of multi-walled carbon nanotubes played an important role in the improved dispersion and adhesion of carbon nanotubes into the epoxy resin. The storage modulus and loss modulus of the composites increased with higher applied frequency. The activation energy of the composites was increased by the effects of a higher heating rate due to the slow heat transfer in the epoxy/carbon nanotube composites. Eventually, the dynamic mechanical properties of the investigated epoxy were significantly improved by the carbon nanotubes dispersed therein via the fluorination treatment.     

The reinforcement role of different amino-functionalized multi-walled carbon nanotubes in epoxy nanocomposites

Functionalization with different amino groups of multi-walled carbon nanotubes was achieved and nanotube-reinforced epoxy nanocomposites were prepared by mixing amino-functionalized multi-walled carbon nanotubes with epoxy resin. Differential scanning calorimetry, thermogravimetric analysis and bending tests were used to investigate the thermal and mechanical properties of the nanocomposites. The results showed that different kinds of amino-functionalized multi-walled carbon nanotubes would have different effects on the thermal and mechanical properties of the nanocomposites. The reinforcement mechanism of amino-functionalized multi-walled carbon nanotubes in epoxy resin was discussed.     

Viscoelastic properties of multi-walled carbon nanotube/epoxy composites using two different curing cycles

Along with carbon nanotubes (CNT) morphology, impurity, and functionalization, polymer curing cycle is another important factor in determining the mechanical properties of the CNT/polymer composite samples. This work investigates the effect of two different curing cycles on mechanical and thermo-mechanical properties of the nanotube in the composite in order to optimize the curing condition in term of time and temperature. Nanocomposite samples were prepared by mixing multi-wall carbon nanotubes with epoxy resin using sonication method. The mechanical and viscoelastic properties of the resulting composite samples were evaluated by performing tensile and dynamic mechanical thermal analyses (DMTA) test. The results indicate that the mechanical and viscoelastic properties of pure epoxy and composite samples have been affected by the condition curing process. Concerning viscoelastic modeling, the COLE–COLE diagram has been plotted by the result of DMTA tests. These results show a good agreement between the Perez model and the viscoelastic behavior of the composite.     

不同官能化碳纳米管对MWCNTs-碳纤维/环氧树脂复合材料力学性能的影响

为研究加入不同官能化碳纳米管对环氧树脂力学性能的影响,通过对羧基化多壁碳纳米管(MWCNTsCOOH)进行化学处理,得到表面接枝乙二胺的碳纳米管(MWCNTs-EDA)。分别将MWCNTs-COOH和MWCNTs-EDA分散在环氧树脂中,通过热熔法制备环氧树脂中含有碳纳米管的T700碳纤维预浸料,并热压成准各向同性复合材料层合板。结果表明:MWCNTs-EDA在环氧树脂中的分散性优于MWCNTs-COOH,MWCNTsEDA本身具有固化反应活性,加入后对基体的交联密度影响较小。与MWCNTs-COOH相比,MWCNTs-EDA可以有效改善环氧树脂及碳纤维/环氧树脂复合材料的力学性能。当MWCNTs-EDA含量为1.0wt%时,MWCNTs-碳纤维/环氧树脂准各向同性复合材料层合板的压缩性能、弯曲性能和冲击后压缩强度分别提高了14.7%、40.9%和20.6%。     

Single-walled carbon nanotube incorporated novel three phase carbon/epoxy composite with enhanced properties

In the present work, single-walled carbon nanotubes were dispersed within the matrix of carbon fabric reinforced epoxy composites in order to develop novel three phase carbon/epoxy/single-walled carbon nanotube composites. A combination of ultrasonication and high speed mechanical stirring at 2000 rpm was used to uniformly disperse carbon nanotubes in the epoxy resin. The state of carbon nanotube dispersion in the epoxy resin and within the nanocomposites was characterized with the help of optical microscopy and atomic force microscopy. Pure carbon/epoxy and three phase composites were characterized for mechanical properties (tensile and compressive) as well as for thermal and electrical conductivity. Fracture surfaces of composites after tensile test were also studied in order to investigate the effect of dispersed carbon nanotubes on the failure behavior of composites. Dispersion of only 0.1 wt% nanotubes in the matrix led to improvements of 95% in Young's modulus, 31% in tensile strength, 76% in compressive modulus and 41% in compressive strength of carbon/epoxy composites. In addition to that, electrical and thermal conductivity also improved significantly with addition of carbon nanotubes.     

静电植绒法处理多壁碳纳米管改性玻纤织物/环氧树脂复合材料的制备及力学性能

为提高玻纤增强环氧树脂复合材料的力学性能,采用静电植绒法将多壁碳纳米管(MWCNTs)附着在玻纤织物表面,得到改性的玻纤织物。利用一种低黏度的环氧树脂和所制得的改性织物,采用真空辅助成型工艺(VARI)制备了MWCNTs改性格玻纤织物/环氧树脂复合材料层合板,表征了层合板的力学性能。对进行力学实验后的MWCNTs改性玻纤织物/环氧树脂复合材料试样断口进行了SEM和OPM观察。结果显示:与未添加MWCNTs的玻纤织物/环氧树脂复合材料层合板相比,添加了MWCNTs的层合板的拉伸强度降低了10.24%,弯曲强度降低了13.90%,压缩强度降低了17.33%,拉伸模量和弯曲模量分别提高了19.38%和16.04%,压缩模量提高了13%;MWCNTs与玻纤织物之间的结合较弱,在拉伸作用下,存在明显的脱粘和分层;将改性玻纤织物在200℃下热压处理2h后,制备的MWCNTs改性玻纤织物/环氧树脂复合材料层合板的力学性能均有所提高,热压处理后树脂与玻纤织物之间的界面结合得到改善。     

Processing,characterization, and modeling of carbon nanotube-reinforced multiscale composites

Carbon fiber-reinforced epoxy composites modified with carbon nanotubes (CNTs) were fabricated and characterized. High-energy sonication was used to disperse CNTs in the resin, followed by infiltration of fiber preform with the resin/CNT mixture. The effects of sonication time on the mechanical properties of “multiscale” composites, which contain reinforcements at varying scales, were studied. A low CNT loading of 0.3 wt% in resin had little influence on tensile properties, while it improved the flexural modulus, strength, and percent strain to break by 11.6%, 18.0%, and 11.4%, respectively, as compared to the control carbon fiber/epoxy composite. While sonication is an effective method to disperse CNTs in a resin, duration, intensity, and temperature need to be controlled to prevent damages imposed on CNTs and premature resin curing. A combination of Halpin–Tsai equations and woven fiber micromechanics was used in hierarchy to predict the mechanical properties of multiscale composites, and the discrepancies between the predicted and experimental values are explained.     

碳化硅颗粒填充的碳纳米管/环氧树脂复合材料的吸波性能

以碳纳米管、碳化硅颗粒为原料制备环氧树脂复合吸波材料,并对其吸波性能进行测试,研究了碳纳米管、碳化硅颗粒含量与复合材料吸波性能的关系.结果表明碳纳米管、碳化硅颗粒的含量对复合材料的吸波性能有较大影响.随碳纳米管含量的增加,碳纳米管/环氧树脂复合材料的吸波性能先提高后降低,碳纳米管含量存在最佳值(12%,质量分数).将碳...     

表面官能团化多壁碳纳米管/环氧树脂复合材料的制备及性能

本文首先将多壁碳纳米管(MWNT)进行表面化学修饰,接入羧基、胺基等官能团,采用红外光谱进行了表征.以纯化后的MWNT和表面化学修饰的MWNT作为填料,制备了MWNT /环氧树脂复合材料,研究了MWNT的加入对环氧树脂的力学性能、电学性能、热稳定性和玻璃化转变温度等的影响,并利用场发射电镜观察了胺基化MWNT在环氧树脂基体中的分散情况.     

分散方法对低含量碳纳米管玻纤/环氧层板性能的影响

采用超声波振荡与超声波破碎两种分散方法制备了低含量碳纳米管(CNTs)增强的环氧树脂, 研究了CNTs对树脂流变特性、 固化特性和力学性能的影响。进一步采用该树脂体系通过真空灌注工艺(VARIM)制备了CNTs含量为0.01%的CNTs-玻璃纤维/环氧树脂复合材料层板, 研究了两种分散方式下CNTs对复合材料层板力学性能的影响和CNTs的增强机制。结果表明: 超声波破碎分散使CNTs长度变短, 分散性更好, 与超声波振荡分散方式相比, CNTs对树脂增黏效果和树脂固化反应的影响更明显。采用双真空灌注工艺, 两种超声波分散方式下CNTs均提高了复合材料的弯曲性能、 层间剪切性能和树脂与纤维的粘结强度, 而单真空灌注工艺下CNTs的增强效果不明显, 说明受纤维过滤作用的影响, 选择合适的灌注工艺和CNTs分散方式, 低含量CNTs可实现对灌注工艺复合材料层板的增强。