Preserving Melons by Osmotic Dehydration in a Ternary System Followed by Air-Drying

In this study, the effect of different osmotic solution concentrations (20–60% w/w of sucrose with 10% w/w NaCl salt), fruit to solution ratios (1:9–1:3), immersion times (0.5–4 h), and temperatures (15–55°C) on the mass transfer kinetics during osmotic dehydration of melons (Curcumis melo L.) in ternary solution namely sucrose–salt–water followed by air-drying were investigated. The effective diffusion coefficients for sucrose and water during osmotic dehydration were determined, assuming osmotic dehydration to be governed by Fickian diffusion. The estimated parameters allowed optimizing the system to reduce total processing time. The optimum treatments were with 50% sucrose and 10% NaCl salt concentration, fruit to solution ratio of 1:4 for 1 h at 45°C. Samples non-treated and pre-treated in optimized conditions were dried in a hot-air dryer at 60°C until equilibrium was achieved after 2.5 h. Pre-treatment reduced the air-drying period in up to 6.8 h.     

Effect of Thermosonic Pretreatment and Microwave Vacuum Drying on the Water State and Glass Transition Temperature in <Emphasis Type="Italic">Agaricus bisporus</Emphasis> Slices

This study aimed to understand the micromechanism of thermosonic pretreatment and microwave vacuum drying on Agaricus bisporus. The water state and glass transition temperature (T _g ) of fresh and thermosonically treated Agaricus bisporus slices during microwave vacuum drying were studied using differential scanning calorimetry (DSC), low-field nuclear magnetic resonance (LF-NMR), and magnetic resonance imaging (MRI). Results showed that four population groups were contained in the initial distribution of transverse relaxation time (T ₂) data of fresh A. bisporus slices: T ₂₁ (0.38–7.05 ms), T ₂₂ (9.33–32.75 ms), T ₂₃₁ (37.65–265.61 ms), and T ₂₃₂ (305.39–811.13 ms). Thermosonic pretreatment significantly decreased the initial free water content of A. bisporus sample but was accompanied by a sharp increase in its immobilized water. “Semi-bound water transfer” appeared during microwave vacuum drying (MVD) at moisture contents (X _w ) of 0.70 and 0.60 g/g (wet basis (w.b.)) for untreated and thermosonically treated samples, respectively. MVD caused dramatic changes in the water state and enhanced the T _g by decreasing the content and mobility of immobilized water in A. bisporus tissues. The mobility of semi-bound water for thermosonically and MVD-treated samples was higher than for MVD-untreated samples, resulting in T _g values decreasing by approximately 2–11.5 °C, but the uniformity of water distribution in thermosonic-treated and MVD-treated samples was better at X _w  ≤ 0.52 g/g (w.b.).     

Pulsed Vacuum Osmotic Dehydration of Beetroot,Carrot and Eggplant Slices: Effect of Vacuum Pressure on the Quality Parameters

Pulsed vacuum osmotic dehydration (PVOD) is a widely used technique for reducing moisture content and water activity in biological products. This study aimed to analyze the effect of vacuum application (VA) on PVOD of beetroot, carrot, and eggplant slices, with respect to chemical (moisture, water activity, specific pigments, polyphenols, and sodium content), optical (color), mechanical (shrinkage, maximum stress, and elasticity), and structural (microstructure) properties. PVOD was conducted at three different vacuum pressures (0, 40, and 80 kPa, for 10 min), during a total process time of 300 min. Osmotic processing was performed at 35 °C by using a ternary osmotic solution [40% sucrose +?10% sodium chloride (w/w)]. Eggplant and carrot samples were more sensitive to VA, compared to beetroot. This was related to their porous and less compact structure. In general, VA reduced the moisture content and water activity and preserved the carotenoid content. VA caused loss of betalain and phenolic acid, favored sodium uptake, and induced significant changes in the optical, mechanical, and structural properties, compared to the osmotic processing conducted at atmospheric pressure.     

A New Chemical Marker-Model Food System for Heating Pattern Determination of Microwave-Assisted Pasteurization Processes

New chemical marker-model food systems with d-ribose and NaOH precursors as color indicators and gellan gels as chemical marker carrier were explored for the assessment of the heating pattern of in packaged foods processed in microwave-assisted pasteurization system (MAPS). In determining appropriate precursor concentrations, a solution of 2% (w/w) d-ribose and 60 mM NaOH was heated at 60–90 °C for 0–20 min. The solution absorbance at 420 nm increased linearly, while the color parameters L* decreased linearly with heating time at all processing temperatures. In storage, the produced brown color was stable at 4 and 22 °C within 7 days. The new chemical marker-model foods were prepared by mixing 2% (w/w) d-ribose and 60 mM NaOH with 1% (w/v) low-acyl gellan gum and 20 mM CaCl₂·2H₂O solution. The dielectric constant of the model food samples decreased with the addition of sucrose, and the loss factors increased with the addition of salt. After processing in the pilot MAPS, the heating pattern and cold and hot spots in the new chemical marker-model food system could be clearly recognized and precisely located through a computer vision method. This is the first time that the caramelization reaction was used as a time-temperature indicator in gellan gel model food. This study shows the possibility of using the new chemical marker-model food system for heating pattern determination of the MAPS.     

Partition Behaviors of Different Polar Anthocyanins in Aqueous Two-Phase Systems and Extraction of Anthocyanins from <Emphasis Type="Italic">Nitraria tangutorun</Emphasis> Bobr. and <Emphasis Type="Italic">Lycium ruthenicum</Emphasis> Murr.

This study aimed to investigate the partition behaviors of various polar anthocyanins in NaH₂PO₄/(NH₄)₂SO₄-ethanol aqueous two-phase systems (ATPS) and to extract anthocyanins from Nitraria tangutorun Bobr. and Lycium ruthenicum Murr. Anthocyanins in Hibiscus sabdariffa L., Morus atropurpurea Roxb., N. tangutorun, and L. ruthenicum were profiled using HPLC-ESI-MS/MS and HPLC-DAD, and the partition behaviors of total anthocyanins and main anthocyanins were studied. The partition coefficient of anthocyanins increased with increased hydrophobicity, and low-polarity anthocyanins exhibited a higher preference for the top phase in NaH₂PO₄/(NH₄)₂SO₄-ethanol ATPS. Additionally, the NaH₂PO₄-ethanol ATPS gave higher selectivity and total anthocyanin yield than the (NH₄)₂SO₄-ethanol system. Extraction at 65 °C for 45 min and at 45.5 °C for 45 min using 28% NaH₂PO₄ and 26% ethanol (w/w) led to the recovery of 98.91 ± 0.03% of N. tangutorun anthocyanins (3.62 ± 0.05 mg/g) and 99.84 ± 0.01% of L. ruthenicum anthocyanins (13.16 ± 0.29 mg/g) from raw material; more than 70% of total sugars were removed in a single step. NaH₂PO₄-ethanol aqueous two-phase extraction is a promising method for extracting anthocyanins from N. tangutorun and L. ruthenicum.     

Production and Characterization of Gelatin Spherical Particles Formed via Electrospraying and Encapsulated with Polyphenolic Antioxidants from <Emphasis Type="Italic">Momordica charantia</Emphasis>

This study dealt with the production and characterization of gelatin nanospheres and encapsulation with Momordica charantia, commonly known as bitter gourd fruit vegetable extract (BGE). The impact of encapsulation and increasing the encapsulate loading on various physiochemical characteristics of gelatin polymeric entities as well as antioxidative attributes of BGE was studied. Nanospheres were formed via an electrospraying process conducted at 20 kV, 0.5 mL/h, and 10 cm of voltage, flow rate, and emitter/collector distance, respectively. The spherical beads were encapsulated with BGE at 5 to 15% (w/w%) loading rate. Morphological analysis through scanning electron microscopy (SEM) and atomic force microscopy (AFM) demonstrated that nanospheres could be successfully produced. Furthermore, nanosphere encapsulation of the extract was demonstrated in transmission electron microscope (TEM) micrographs. Spectroscopic analysis indicated no chemical interactions between core and wall materials. The thermal stability of encapsulated nanoparticles slightly increased and the glass transition temperature (T_g) disappeared due to increased crystallinity. Thermogravimetric graphs of encapsulated spherical beads, at all core loadings, showed an additional phase ranging from 138 to 249 °C, overlapping with the BGE’s main TGA degradation phase. The presence of this phase, which was absent from empty bead thermograms, confirmed encapsulation occurrence during electrospraying process. Furthermore, an average of 80% of antioxidative content and potency of the extract was conserved during the encapsulation process. Moreover, phenolic content and antioxidative activity of the encapsulated extract showed higher stability than extracts while stored at refrigerated and ambient conditions.     

Viability of Probiotics in Goat Cheese During Storage and Under Simulated Gastrointestinal Conditions

The objective of this study was to evaluate the suitability of two strains of probiotic bacteria (Bifidobacterium animalis subsp. lactis and Lactobacillus rhamnosus) incorporated individually into Boursin-type goat cheese and their in vitro resistance through the passage of the gastrointestinal tract in the cheese. The viability of B. lactis and Lb. rhamnosus cultures was unaffected throughout 35 days of storage at 4 °C, with a final count of >?7 log CFU/g. No significant difference (p?>?0.05) was observed between probiotic treatments and control in relation to pH and titratable acidity. B. animalis presented greater resistance to the artificial gastric and enteric juices than Lb. rhamnosus, with mean decreases in the initial populations of 0.2 and 4.0 log CFU/g within 35 days of storage, respectively. The addition of probiotic cultures did not affect the consumer acceptance of the goat cheeses. Three segments of consumers with different liking were identified. The results demonstrated that “Boursin” goat cheese is a promising matrix for the incorporation and protection of B. animalis subsp. lactis.     

Development and characterization of reconstituted hydrogel from <Emphasis Type="Italic">Aloe vera</Emphasis> (<Emphasis Type="Italic">Aloe barbadensis</Emphasis> Miller) powder

Structural and rheological characterization of reconstituted hydrogels developed from A. vera non-fibrous alcohol insoluble residue (NFAIR) powder using different methods [viz., shaking (S), heating-shaking (HS), and heating (H)] and concentrations (viz., 0.2–1.6 %, w/v) was carried out. Functional group distribution by FTIR spectroscopy and Congo red (CR) method revealed the presence of acetylated acemannan in A. vera powder. Dynamic oscillation studies of A. vera (NFAIR) fluids at all concentrations of 0.2–1.6 %, w/v, showed gel strength in the order of H > HS > S method. However, in H method, increase in concentration from 0.2 to 1.6 %, w/v showed the conformational transition from semi-diluted solution to weak gel nature. Rheological models described the effect of heating temperatures (HT); 30–90 °C, and times (Ht); 15–60 min on viscoelastic behavior in reconstituted A. vera fluids. The reconstituted A. vera hydrogel prepared with a concentration of 1.6 %, w/v using 50 °C (HT) and 30 min (Ht) condition showed a good agreement with the Power law (storage modulus, G′) and Weak gel model (complex modulus, G*) fitted data (R² > 0.94) resulting higher viscoelastic moduli intercepts; G′₀ (71.5 Pa s ^n′), G″₀ (33.5 Pa s ^n″), lower slopes; n′ (0.22), n″ (0.06), higher network strength (A _F , 121.3 Pa s^1/z ) and number of network (z, 5.3) values. The obtained results suggested that heating at 50 °C/30 min can develop aqueous weak gel networks of A. vera with enhanced gel strength which may be utilized as a novel gelling agent for wide variety of targeted applications in food and pharmaceutical sectors.     

Deposit Generation During Camel and Cow Milk Heating: Microstructure and Chemical Composition

The aim of this study is to identify the chemical composition and the microstructure of the deposits obtained after heating camel and cow milks at 80 °C for 60 min using a laboratory-scale device. Like cow milk, camel milk was affected by heat treatment with the reduction of the non-casein nitrogen content reflecting the denaturation of camel whey proteins. The composition of the deposits generated during heating camel and cow milks at 80 °C for 60 min revealed that while camel deposit contained 57 % w/w protein, cow deposit showed a higher protein content of 69 % w/w. The mineral content was 35 % w/w for camel deposit which was higher than that of cow sample, which was 28 % w/w. SEM of both deposits showed a familiar structure of a protein deposit with large clumps composed of smaller aggregates. Camel deposit showed an amorphous structure due to its deficiency in β-lactoglobulin.     

Smart NMR Method of Measurement of Moisture Content of Vegetables During Microwave Vacuum Drying

Microwave drying is usually combined with vacuum environment in conjunction with hot air flow to draw the moisture rapidly. The moisture content of the vegetables undergoing drying is hard to measure online. This research designed a microwave vacuum drying (MVD)-low-field nuclear magnetic resonance (NMR) smart device and investigated the feasibility of NMR method for online measurement of state of moisture during MVD. The relation between the signal amplitude (A ₂) and the true moisture content (M ₁) of six kinds of vegetables (mushroom, carrot, potato, lotus, edamame, vegetable corn) was fitted to estimate if NMR can measure the M ₁ of vegetables directly. Results showed that A ₂ and M ₁ of different fresh vegetables had no single empirical mathematical model to fit. However, for each kind of these vegetables, the A ₂ and corresponding M ₁ in different MVD stages showed a significant linear relationship. The predicted moisture content (M ₂) of mushroom: M ₂ = 5.25351 × 10^?4 A ₂ ? 0.34042, R = 0.996; carrot: M ₂ = 5.78756 × 10^?4 A ₂ ? 0.14108, R = 0.998; potato: M ₂ = 3.10019 × 10^?4 A ₂ ? 0.10612, R = 0.991; lotus: M ₂ = 2.32415 × 10^?4 A ₂ ? 0.01573, R = 0.998; edamame: M ₂ = 3.13310 × 10^?4 A ₂ ? 0.4198, R = 0.996; vegetable corn: M ₂ = 1.69461 × 10^?4 A ₂ ? 0.09063, R = 0.995. The linear models between M ₂ and A ₂ were able to estimate the end point (M ₁ < 8%) of MVD with a high accuracy (P > 0.950).     

A mathematical model for moisture movement during continous and intermittent drying of <Emphasis Type="Italic">Eucalyptus saligna</Emphasis>

A modified diffusion-based mathematical model is proposed to describe the moisture movement during continuous and intermittent drying of Eucalyptus saligna. This model includes the temperature change, the surface drying coefficient (β _n ) and 2 diffusion coefficients [from green to FSP (D _f ) and from FSP to dry condition (D _o )] as important parameters. The final model expression obtained was M?=?exp (??25 β _n ² D _t /l²) with the β _n used was 1.5807 kg m^?2 s^?1, the D _f was 2.26?×?10^?11 m² s^?1, and the D _o was 5.85?×?10^?12 m² s^?1. The range of temperature change between heating and non-heating phases in the intermittent drying regimes was from 24.9 to 31.8 °C. The R² values obtained when the model was fitted into the drying data of different intermittent regimes ranged from 71.5 to 85.9%. The R² value was 87.4% when the model was fitted into continuous trial data. The high values of R² indicate that the model can be used to understand the moisture reduction both in intermittent and continuous regimes.     

Modeling the Inactivation of <Emphasis Type="Italic">Listeria innocua</Emphasis> and <Emphasis Type="Italic">Escherichia coli</Emphasis> in Fresh-Cut Tomato Treated with Pulsed Light

The effectiveness of pulsed light (PL) treatments to inhibit microorganisms on fresh-cut tomatoes (Lycopersicon esculentum Mill., cv. Daniela) was investigated. Tomato slices inoculated with Escherichia coli or Listeria innocua were exposed to PL treatments (4, 6, or 8 J cm^?2 fluence) and kept cold at 4 °C for 20 days. L. innocua and E. coli counts, gases in the headspace of the containers (O₂ and CO₂), pH, titratable acidity, and soluble solid content were monitored throughout the cold storage. The PL treatments reduced significantly (p < 0.05) initial loads of both microbes. The effect of the PL fluence on the survival number of microoganisms was described by a log-linear model (R ² = 0.849–0.999). At any fixed time within the cold storing, the microbial counts for untreated samples were always higher than those cut tomatoes that had been previously PL-treated. The behavior of L. innocua and E. coli during the storage were well adjusted (R ² > 0.930) by Gompertzian models; the studied microorganisms exhibited different patterns during the storage period. On the other hand, O₂ and CO₂ partial pressures in containers with fresh-cut tomatoes were also significantly affected by PL treatments (p < 0.05). The highest PL fluence caused the greatest changes of O₂ and CO₂ contents. In addition, the application of PL triggered an acceleration of the O₂ consumption during the cold stage. PL treatments might be used to effectively extend the safety of fresh-cut tomatoes over 12 days of storage against E. coli and L. innocua growth.     

Thermal transition and thermo-physical properties of potato (<Emphasis Type="Italic">Solanum tuberosum L</Emphasis>.) var. Russet brown

Potatoes are an important food in many regions of the world and are commonly used in a variety of food products. Thermal transition and thermo-physical properties of potatoes are important in order to design efficient food processes and select appropriate storage conditions. In this study, we determined the thermal transitions and thermophysical properties of raw and blanched/par-fried potato for a temperature range of ??32 to 21.1 °C. Using differential scanning calorimetry, we found an initial freezing point (T_f) at ??1.8?±?0.1 °C, an onset of melting (T_m^′) at ??9.9?±?0.2 °C and an unfreezable water content (X^′_w) for maximally freeze-concentrated raw potato at 0.21 kg water/kg potato. Corresponding values for blanched/par-fried potatoes were ??0.9?±?0.1 °C, ??11.0?±?0.2 °C and 0.18 kg water/kg potato. Results show that an increase in solids content decreased T_f of both raw and blanched potatoes. We modelled the relationship between them using the Chen model. The apparent specific heat (C_app) increased around T_f to 31.7?±?1.13 kJ/kg K for raw potato and 26.7?±?0.62 kJ/kg K for blanched/par-fried potato. For frozen raw potato at ??32 °C, thermal diffusivity (α) was 0.89?±?0.01?×?10?^?6 m²/s and thermal conductivity (k), 1.82?±?0.14 W/m K, respectively. These values were higher for frozen raw potato than for the unfrozen raw potato (0.15?±?0.01?×?10?^?6 m²/s and 0.56?±?0.08 W/m K, respectively at 21.1 °C). The apparent density (ρ) of frozen raw potato (992?±?4.00 kg/m³ at ??32 °C) was less than that for unfrozen raw potato (1053?±?4.00 kg/m³ at 21.1 °C), and a similar trend was obtained for blanched/par-fried potato (993?±?2.00 kg/m³ at ??32 °C and 1188?±?7.00 kg/m³ at 21.1 °C, respectively). This study established a correlation between thermo-physical properties and temperature. Findings may be used to inform the design and optimization of freezing processes and frozen storage for potato products.     

Effects of organic acid pretreatment on microstructure,functional and thermal properties of unripe banana flour

Starch availability has been implicated in unripe matured banana (Musa species), which when processed yields flour suitable for application in low gluten and composite wheat formulations. Unripe Musa species: Williams, Luvhele, Mabonde and Muomva-red obtained from fruit bunch were pretreated with ascorbic, citric and lactic acids, processed into 50 g of flour and characterised for their functional and thermal properties. Scanning electron microscope of unripe banana flour (UBF) showed varying micrographs of flour, with polygonal for Luvhele, oval for Mabonde, elongated for Muomva-red and between polygonal and spherical for Williams. The bulk density of UBF samples was within the range of 0.66–0.84 g/mL for all organic acid pretreatment while citric acid pretreated UBF had the least browning index. Significant difference (p < 0.05) was recorded in swelling power with no significant difference in water solubility index except for Mabonde UBF. Thermal properties showed single endothermic transition for all UBF samples at various pretreatment concentration. The onset temperature (To) of UBF ranges from 49.82 to 65.59 °C, peak temperature (Tp) from 60.11 to 76.71 °C, conclusion temperature (Tc) from 70.36 to 94.16 °C and enthalpy of gelatinization (ΔH) from 2.61 to 32.24 J/g. Short amylopectin chains present in starch of UBF was attributed to low To, Tp, Tc and ΔH values recorded for Mabonde cultivar, while the contribution of heat-moisture treatment rather than organic acid pretreatment of UBF samples was attributed to different gelatinization and transition temperatures recorded for all cultivars examined.     

Resistance of rubberwood (<Emphasis Type="Italic">Hevea brasiliensis</Emphasis>) treated with chitosan or silane against surface molds

The aim of this study was to determine the efficacy of chitosan and methoxysilane in the prevention of surface mold growth on rubberwood. Three different chitosan samples were tested; C1 (Mw 37 kDa), C2 (Mw 5.4 kDa) and C3 (Mw 3.5 kDa). Radial growth inhibition assay of the chitosan samples was investigated at concentrations ranging from 0.063 to 0.5 %w/v against Aspergillus niger BAM 4 and Penicillium decumbens CBS 121928. Chitosan samples C1 and C3 exhibited strong antifungal activity against both molds. Rubberwood samples were either vacuum or dip treated with varying concentrations of chitosan or silane solution. The content of chitosan in wood showed that after the leaching test, chitosan was well retained in both vacuum and dip treated wood. The concentration of silicon in wood showed similar results. The vacuum treated wood samples with chitosan C1 and C3 at 1 %w/v concentration had strong resistance against A. niger BAM 4. However, dip treated rubberwood samples with 2 %w/v chitosan solutions showed lower resistance against A. niger BAM 4. On the other hand, both vacuum and dip treated rubberwood samples with chitosan had no resistance against P. decumbens CBS 121928. The silane treated wood samples showed no resistance to fungal growth.     

Biological activities of lactobacilli relevant to cardiovascular health in skim milk

In this study, skim milk was fermented using 14 Lactobacillus strains for 16 h at 42 °C or for 48 h at 25 °C. On conclusion of fermentation, the proteolytic, angiotensin converting enzyme-inhibitory (ACE-I), and antioxidant activities as well as the inhibition of thrombin and cholesterol micellar solubility were determined. The results revealed that Lb. paracasei B-4564 exhibited the highest ACE-I activity (68.11%) under the 42 °C for 16 h condition, while Lb. rhamnosus B-1445 demonstrated the highest ACE-I activity (92.23%) under the 25 °C for 48 h condition. Lb. paracasei B-4564 exhibited the highest inhibition rate of thrombin (42.43 and 48.10%) and cholesterol (68.60 and 87.01%) under the 42 °C for 16 h and 25 °C for 48 h conditions, receptively. Lb. rhamnosus B-442 exhibited the highest DPPH radical scavenging activity of 95.63 and 62.89% under the 42 °C for 16 h and 25 °C for 48 h conditions, receptively. Lb. rhamnosus B-1445 demonstrated the highest Fe²⁺ chelating activity and reducing power under both the tested fermentation conditions.     

Glass Transition and State Diagram for Jujube Powders With and Without Maltodextrin Addition

Both water activity and glass transition concepts were used for stability evaluation of jujube powder in this study. The water sorption behaviour at 25, 35 and 45 °C and the relationship between water content (X _w), glass transition temperature (T _g) and water activity (a _w) were investigated for jujube powder with and without the maltodextrin addition. Moisture sorption isotherms of different jujube powders were of type III and BET model was the best for fitting the experimental data. The equilibrium moisture content of jujube powder containing 20% maltodextrin at a given a _w was lower than that of pure jujube powder. However, temperature had no significant effect on the moisture sorption of jujube powders. Values of T _g of different jujube powders were obtained using differential scanning calorimetry and the glass transition line was fitted to the Gordon-Taylor model. A depression in T _g with increasing water content was observed. State diagrams of different jujube powders were established based on the moisture sorption isotherm and the glass transition curve. Results showed that jujube powders with and without maltodextrin addition were stable at 25 °C when the water content was lower than 0.0673 and 0.0566 g/g solid, respectively.     

Green Banana (<Emphasis Type="Italic">Musa cavendishii</Emphasis>) Osmotic Dehydration by Non-Caloric Solutions: Modeling,Physical-Chemical Properties,Color, and Texture

Osmotic dehydration effects on the kinetics and on some quality attributes of green banana slices (Musa cavendishii) at 25 °C with non-caloric solutes (glycerol, sorbitol, and a mixture of both) at concentrations varying from 40 to 60 g/100 g for up to 6 h were studied. The three-component diagram showed that the first pseudo-equilibrium was achieved, and the water pseudo-diffusion coefficient presented higher values with glycerol solutions. A modified Peleg’s model was applied to obtain the maximum water loss. Changes in green banana physical-chemical properties were observed: moisture content from 1.25 to 0.19 kg/kg dry basis, soluble solute content from 5.4 to 16.9 °Brix; total color-difference from 2.7 to 15.8; and the maximum biaxial extensional viscosity from 0.63 to 1.53 MPa s. Moreover, the obtained low chroma difference values suggest that the osmotically drying process may be a suitable technique to preserve the final color of green banana slices.     

Determination of optimal machining parameters of massive wooden edge glued panels which is made of Scots pine (<Emphasis Type="Italic">Pinus sylvestris</Emphasis> L.) using Taguchi design method

In this paper, the optimization of CNC machining parameters was conducted using the Taguchi design method on the surface quality of massive wooden edge glued panels made of Scots pine (Pinus sylvestris L.). Five machining parameters and their effects on surface roughness were evaluated. These parameters included cutters type, tool clearance strategy, spindle speed, feed rate and depth of cut. An analysis of variance (ANOVA) was performed to identify significant factors affecting the surface roughness (R _a and R _z ). Optimum machining parameter combinations were acquired by conducting an analysis of the signal-to-noise (S/N) ratio. Optimal cutting performance for R _a and R _z was obtained for Cutter 1, at a tool clearance strategy of a raster 16,000 rpm spindle speed, 1000 mm/min feed rate and 4 mm depth. Based on the results of the confirmation tests, R _a decreased 2.8 times and R _z decreased 2.0 times.     

Effect of Tannin Extracts on Biofilms and Attachment of <Emphasis Type="Italic">Escherichia coli</Emphasis> on Lettuce Leaves

Lettuce is often involved in foodborne outbreaks caused by pathogenic Escherichia coli. Current control strategies have often proved ineffective to ensure safe food production. For that reason, the present study compared the efficacy of tannin extracts and chlorine treatments on the reduction of E. coli ATCC 25922 adhered to lettuce leaves. E. coli was inoculated artificially on leaf surfaces of fresh crisp lettuce. Effectiveness of water, chlorine (200 mg/L), and three commercial available tannin extracts from Acacia mearnsii De Wild. (tannin AQ (2 %, w/v), tannin SG (1 %, v/v) and tannin SM (1 %, v/v)) treatments was evaluated using the viable plate count method and scanning electron microscopy (SEM). SEM results revealed that bacterial cells are attached as individual cells and in clusters to the leaf surface after 2 h of incubation. Biofilm formation was observed after 24 h of incubation. The tannin SM treatment was able to reduce counts in approximately 2 log CFU/cm² on leaf segments. However, treatment was less effective in the reduction of E. coli counts after 24 h of incubation when compared to 2 h incubation of the same extract. The results suggest that the tannin SM extract diminishes E. coli counts adhered to and under biofilm formation on lettuce leaves and its effect is similar to the use of chlorine solutions.