Synthesis of poly(1-β-naphthyl-2-phenylacetylene) membranes through desilylation and their properties

The polymerization of 1-β-naphthyl-2-[(p-trimethylsilyl)phenyl]acetylene (8a) with TaCl₅-n-Bu₄Sn in cyclohexane provided a high molecular weight polymer (9a) (M_w=3.4×10⁶). The corresponding monomers having p-dimethyl-t-butylsilyl and p-dimethyl(10-pinanyl)silyl groups in place of p-trimethylsilyl group in 8a also polymerized in a similar way to give high molecular weight polymers (9b, 9c, respectively; M_w>1×10⁶). All these polymers were soluble in many common solvents such as toluene and chloroform, and provided free-standing membranes by casting from toluene solution. The oxygen permeability coefficients (P_O2) of 9a at 25 °C was as high as 3500 barrers. The membrane of poly(1-β-naphthyl-2-phenylacetylene) (10a) was prepared by desilylation of the membrane of 9a with trifluoroacetic acid. Polymer 10a was insoluble in any solvents, and showed high thermal stability (the onset temperature of weight loss in air ∼470 °C). The P_O2 value of 10a reached 4300 barrers. Not only the membrane of 9c but also its desilylation product 10c exhibited large optical rotations ([α]_D=+2924 and +9800°, respectively) and strong CD signals. This indicates that the membrane of 10c maintains the helical main chain conformation of 9c with a large excess one-handed helix sense.     

Effect of Fumed Silica Nanoparticles on the Gas Permeation Properties of Substituted Polyacetylene Membranes

Summary The gas permeability of three substituted polyacetylenes, poly(1-chloro-2-phenylacetylene) (PClPA), poly[1-phenyl-2-(4-trimethylsilyl)phenylacetylene] (PTMSDPA), and poly[1-(trimethylsilyl)-1-propyne] (PTMSP), increased systematically with increasing content of nonporous fumed silica (FS) nanoparticles. For instance, the oxygen permeability coefficient (PO₂) of PClPA containing 30 wt % FS was 86 barrers, which was 10 times higher than that of the unfilled polymer (PO₂=8.6 barrers). The extent of permeability increase with the addition of FS was smaller when the permeability of the original polymer was higher. The order of the permeability increase in FS-filled polymers was as follows: PClPA > PTMSDPA > PTMSP. The addition of FS resulted in the decrease of O₂/N₂ permselectivity of these polymers. The H₂/CH₄ permselectivity largely decreased with increasing FS content in PClPA, while it hardly changed with FS loading in PTMSP. The gas solubility of PClPA was practically independent of FS content, and the increase in gas permeability in filled PClPA resulted from an increase in diffusivity with the addition of FS.     

Synthesis and gas permeability of ester substituted poly(p-phenylene)s

Polymerizations of various ester substituted 2,5-dichlorobenzoates [substituent: linear alkyl groups (1a-f), branched alkyl groups (1g-l), cyclohexyl groups (1m-o), phenyl groups (1p-r), and oxyethylene units (1s-v)] were investigated with Ni-catalyzed/Zn-mediated system in 1-methyl-2-pyrrolidone (NMP) at 80 °C. Most of monomers bearing linear and branched alkyl groups successfully polymerized to give relatively high-molecular-weight polymers (M_n = 10,000-20,800). However, the molecular weight of the polymer having eicocyl groups was low because of steric hindrance of long alkyl chain. The polymerizations of cyclohexyl 2,5-dichlorobenzoate and phenyl 2,5-dichlorobenzoate produced low-molecular-weight polymers, while the polymerizations of monomers with alkyl cyclohexyl and alkyl phenyl groups proceeded to afford polymers with relatively high-molecular-weights. The polymers possessing oxyethylene units were obtained, but the molecular weights were low when the oxyethylene chains were long. The gas permeability of membranes of poly(p-phenylene)s with alkyl chains increased as increasing the length of alkyl chain. The membranes of poly(p-phenylene)s with phenyl groups and oxyethylene units exhibited high densities and relatively low gas permeability. However, the CO₂/N₂ separation factor of membrane of poly(p-phenylene) having oxyethylene units was as large as 73.6.     

Synthesis and characterization of poly(tetramethylsilarylenesiloxane) derivatives bearing benzodithiophene moieties

Poly(tetramethylsilarylenesiloxane) derivatives bearing benzo[1,2-b;4,5-b′]dithiophene (P1) and benzo[2,1-b;3,4-b′]dithiophene (P2) moieties were prepared via polycondensation of the corresponding disilanol monomers, that is, 2,6-bis(dimethylhydroxysilyl)benzo[1,2-b;4,5-b′]dithiophene (M1) and 2,7-bis(dimethylhydroxysilyl)benzo[2,1-b;3,4-b′]dithiophene (M2), respectively. It was deduced that P1 is a crystalline polymer while P2 is an amorphous one from the results of differential scanning calorimetry (DSC). Bathochromic and hyperchromic effects were observed in the absorption and fluorescence spectra when dimethylsilyl substituents were introduced on the benzo[1,2-b;4,5-b′]dithiophene and benzo[2,1-b;3,4-b′]dithiophene skeletons. The fluorescence quantum yields (Φ_Fs) were not improved by the introduction of dimethylsilyl groups onto the benzo[1,2-b;4,5-b′]dithiophene and benzo[2,1-b;3,4-b′]dithiophene skeletons, whereas the improvement in the Φ_Fs was remarkable in the case of poly(tetramethylsilarylenesiloxane) derivatives that possessed the corresponding fused benzene ring systems, i.e., poly(tetramethyl-2,6-silanthrylenesiloxane) and poly(tetramethyl-1,8-silphenanthrylenesiloxane).     

Synthesis and properties of various poly(diphenylacetylenes) containing tert-amine moieties

The polymerization of diphenylacetylene derivatives possessing tert-amine moieties, such as triphenylamine, N-substituted carbazole and indole, was examined in the presence of TaCl₅-n-Bu₄Sn (1:2) catalyst. A polymer with high molecular weight (M_w = 570 × 10³) was obtained in good yield by the polymerization of diphenylamine-containing monomer 1b, whereas the isopropylphenylamine derivative (1c) gave a polymer with relatively low molecular weight (M_w = 2.4 × 10³). The polymerization of monomer 1d containing cyclohexylphenylamine group did not proceed; however, carbazolyl- and indolyl-containing monomers also produced polymers. Poly(1b), poly(2f) and poly(4b) could be fabricated into free-standing membranes by casting toluene solutions of these polymers. The gas permeability of poly(1b) was too low to be evaluated accurately whereas poly(4b) possessing two chlorine atoms in the repeating unit showed higher gas permeability than that of poly(1b); furthermore, poly(2f) having trimethylsilyl and 3-methylindolyl groups exhibited relatively high gas permeability (). In the cyclic voltammograms of diphenylamino group-containing polymers, poly(1b) and poly(2b), the intensities of oxidation and reduction peaks decreased more than those of carbazolyl-containing poly(2a). The molar absorptivity (?) of poly(1b) at ∼700 nm increased with increasing applied voltage in the UV-vis spectrum.     

Synthesis and properties of helical polyacetylenes containing carbazole

Novel acetylene monomers containing carbazole with chiral menthyl and bornyl groups, 9-(1R,2S,5R)-menthyloxycarbonyl-2-ethynylcarbazole (1), 9-(1S,2R,5S)-menthyloxycarbonyl-2-ethynylcarbazole (2), 9-(1R,2S,5R)-menthyloxycarbonyl-3-ethynylcarbazole (3) and 9-(1S)-bornyloxycarbonyl-2-ethynylcarbazole (4) were synthesized and polymerized with a Rh catalyst to give the corresponding polymers [poly(1)-poly(4)] with moderate M_n value of (11.5-92.2) × 10³ in good yields (77-89%). CD spectroscopic studies revealed that poly(1), poly(2) and poly(4) took predominantly one-handed helical structure in CHCl₃, THF, toluene, and CH₂Cl₂, while poly(3) did not. Addition of methanol to CHCl₃ solutions of poly(1) and poly(2) resulted in the formation of aggregates showing smaller CD signals at 275 and 320 nm. The helical structure of poly(1) and poly(2) was very stable against heating. The polymers emitted fluorescence in 0.40-2.90% quantum yields. Poly(4) exhibited an obvious oxidation peak at 1.10 V. The polymers were thermally stable below 300 °C.     

Synthesis and gas permeability of nitrated and aminated Poly(diphenylacetylene)s

Poly(diphenylacetylene) [PDPA] derivatives were nitrated using a mixture of nitric acid and sulfuric acid. Nitration of poly[1-(p-trimethylsilyl)phenyl-2-phenylacetylene] (1a) proceeded, and the nitro groups were substituted to trimethylsilyl groups on benzene rings. The degree of nitration (DN) increased with reaction time, and it reached 0.41 for 3.0 h. Fluorine-containing PDPA (1b and 1c) showed less reactivity for nitration, and the DNs were only 0.18 and 0.06, respectively, under the same conditions. Nitration of PDPAs having n-butyl and t-butyl groups (1d and 1e) afforded the nitrated PDPAs, whose DN were 0.20 and 0.14, respectively. Reduction of nitro groups on PDPAs proceeded quantitatively to produce the corresponding PDPAs possessing amino groups (3a-e). Aminated PDPAs exhibited high CO₂ permselectivity compared to the corresponding non-aminated PDPAs. The CO₂ permeability coefficients of aminated PDPAs (3a-d) were lower than those of the corresponding polymers (1a-d) because the polymer chain packing was strengthened by the intermolecular interaction between polar amino groups, but t-butyl group-containing aminated PDPA (3e) showed high CO₂ permeability than 1e because the chain packing was weakened by the steric repulsion of bulky t-butyl groups.     

Synthesis and gas permeation properties of various Si-containing poly(diarylacetylene)s and their desilylated membranes

Diarylacetylene monomers having trimethylsilyl groups and other substituents (substituted biphenyl, 1a and 1b; trimethylsilylmethylphenyl, 1c-e) were synthesized and polymerized with TaCl₅-n-Bu₄Sn catalyst to produce the corresponding poly(diarylacetylene)s (2a-d). Polymers 2a-c had high molecular weights and were soluble in common organic solvents. Free-standing membranes of 2a-c as well as previously reported 2f-h were prepared by the solution-casting method. Desilylation of these Si-containing polymer membranes was carried out with trifluoroacetic acid to afford 3a, 3b, and 3f-h. Upon desilylation, biphenyl-containing membranes became less permeable (3a, b), whereas fluorene-containing membranes became more permeable (3f-h). In particular, 3h exhibited extremely high gas permeability (PO₂ = 9800 barrers), which is about the same as that of poly(1-trimethylsilyl-1-propyne). Desilylated membranes 3a and 3f-h showed different gas permeability from that of polymers 2i-k which have the identical chemical structures and obtained directly by the polymerization of the corresponding monomers.     

Syntheses of well-defined poly(siloxane)-b-poly(styrene) and poly(norbornene)-b-poly(styrene) block copolymers using functional alkoxyamines

Functional alkoxyamines, 1-[4-(4-lithiobutoxy)phenyl]-1-(2,2,6,6-tetramethylpiperidinyl-N-oxyl)ethane (2) and 1-[4-(2-vinyloxyethoxy)phenyl]-1-(2,2,6,6-tetramethylpiperidinyl-N-oxyl)ethane (3) were prepared, and well-defined poly(hexamethylcyclotrisiloxane)-b-poly(styrene)[poly(D₃)-b-poly(St)] and poly(norbornene)-b-poly(St) [poly(NBE)-b-poly(St)] were prepared using the alkoxyamines. The first step was preparation of poly(D₃) and poly(NBE) macroinitiators, which were obtained by the ring-opening anionic polymerization of D₃ using 2 as an initiator and the ring-opening metathesis polymerization of NBE using 3 as a chain transfer. The radical polymerization of St by the poly(D₃) and poly(NBE) macroinitiators proceeded in the ‘living’ fashion to give well-defined poly(D₃)-b-poly(St) and poly(NBE)-b-poly(St) block copolymers.     

Synthesis, thermal stability, light emission, and fluorescent photopatterning of poly(diphenylacetylene)s carrying naphthalene pendant groups

Naphthalene (Nap)-containing poly(diphenylacetylene)s with different spacer lengths (-{C₆H₅CC[C₆H₄O(CH₂)_mO-Nap]}_n-; P1(m), m = 4, 6, 8) are synthesized. The monomers are prepared by etherifications of 1,m-dibromoalkanes with 1-naphthol and 1-(4-hydroxy)phenyl-2-phenylacetylene and are polymerized by TaCl₅-n-Bu₄Sn and WCl₆-Ph₄Sn catalysts. Whereas the tantalum-based catalyst gives insoluble products in low yields, the tungsten-based catalyst furnishes soluble polymers with high molecular weights (M_w up to 5.0 × 10⁴) in satisfactory yields (up to 62%). The structures and properties of the polymers are characterized and evaluated by IR, NMR, TGA, UV, PL, and EL analyses. All the polymers are thermally stable: while the polymers lose 5% of their weights at ∼420 °C under nitrogen, no decreases in molecular weights are found after they have been annealed at 200 °C for 2 h in air. When their THF solutions are photoexcited, the polymers emit strong green lights with high efficiencies (up to 98%). No significant shifts in the photoluminescence spectra are observed when the polymers are cast into thin solid films, suggestive of little involvement of aggregative or excimeric emission. A multilayer EL device with a configuration of ITO/P1(8):PVK/BCP/Alq₃/LiF/Al is constructed, which emits a green light of 520 nm with a maximum external quantum efficiency of 0.16%. The spectral stability is outstanding: no recognizable change is observed in the EL spectrum when the device current is raised. Irradiation of a film of P1(8) through a mask photooxidizes and quenches the emission of the exposed regions, resulting in the formation of two-dimensional luminescent photopatterns.     

Synthesis and characterization of donor-acceptor type 4,4′-bis(2,1,3-benzothiadiazole)-based copolymers

A series of novel donor-acceptor type polymers based on 4,4′-bis(2,1,3-benzothiadiazole) were synthesized and characterized. Two soluble regioregular tail-to-tail and head-to-head coupled polymers, poly[7,7′-bis(3-octyl-2-thienyl)-4,4′-bis(2,1,3-benzothiadiazole)] poly[3TBB3T], and poly[7,7′-bis(4-octyl-2-thienyl)-4,4′-bis(2,1,3-benzothiadiazole)] poly[4TBB4T] were synthesized by FeCl₃-mediated oxidative polymerization. To further decrease the band gap of the polymers, vinylene spacers were incorporated into the polymer backbone by Stille coupling of the corresponding monomers and (E)-1,2-bis(tributylstannyl)ethene. A crystal structure of a monomer analog shows near planar arrangement of the aromatic units in the solid state. The optical properties of the monomers and polymers were investigated by steady-state absorption and photoluminescence spectroscopy. Cyclic voltammetry measurements indicate that the polymers could be employed as acceptor materials in polymer-polymer bulk heterojunction solar cells due to their low LUMO energy of about −4.0 eV. A maximum photovoltaic power conversion efficiency of about 0.3% was observed for a 1:1 blend of regioregular poly(3-hexylthiophene) (rr-P3HT) and poly[4TBB4T] and the origin of the moderate efficiency is discussed by interpreting the device current-voltage characteristics, external quantum efficiency and incident light intensity dependence of the power conversion efficiency.     

Preparation and properties of polytolan membranes bearing p-hydroxyl groups

The polymerization of a novel monomer p-(t-butyldimethylsiloxy)tolan (1) with TaCl₅-n-Bu₄Sn provided a high molecular weight polymer (poly(1)), whose M_w reached 4.0×10⁶. The poly(1) membrane was prepared by the casting method, and converted into poly[(p-hydroxy)tolan] (poly(2)) with a mixture of trifluoroacetic acid/water. Whereas poly(1) dissolved in low polarity solvents such as toluene and chloroform, poly(2) was practically insoluble in any solvents, although it partly dissolved in methanol and ethanol. The onset weight loss temperatures of poly(1) and poly(2) in air were 320 and 360 °C, respectively, indicating fair thermal stability among substituted polyacetylenes. The oxygen permeability coefficients (P_O2) of poly(1) was 150 barrers, which is relatively small among polytolan derivatives, while that of poly(2) was 8.0 barrers and smaller owing to the presence of polar hydroxyl groups.     

Synthesis and electro-optical properties of helical polyacetylenes carrying carbazole and triphenylamine moieties

Novel chiral acetylene monomers bearing carbazole and triphenylamine groups, namely, (S)-3-butyn-2-yl 2-(9-carbazolyl)ethyl carbonate (1) and (S)-3-butyn-2-yl 4-(diphenylamino)benzoate (2) were synthesized, and polymerized with Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃] catalyst to give the corresponding polymers with moderate molecular weights (M_n 13.0 × 10³ and 15.5 × 10³) in good yields (86% and 88%). CD spectroscopic studies revealed that poly(1) and poly(2) took predominantly one-handed helical structure in CHCl₃. The helical structures of poly(1) and poly(2) were very stable against heating and addition of MeOH. The solution of poly(1) and poly(2) emitted fluorescence in 0.52% and 7.2% quantum yields, which were lower than those of the corresponding monomers 1 and 2 (22.5% and 76.5%). The cyclic voltammograms of the polymers indicated that the oxidation potentials of the polymers were lower than those of the monomers. The polymers showed electrochromism and changed the color from pale yellow to pale blue by application of voltage, presumably caused by the formation of polaron at the carbazole and triphenylamine moieties. The onset temperatures of weight loss of poly(1) and poly(2) were 225 and 270 °C under air.     

Synthesis and characterization of chiral polythiophenes: Poly [(R)-(−) and (S)-(+)-2-(3′-thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate]

(R)-(−) (1) and (S)-(+)-2-(3′-Thienyl)ethyl N-(3″,5″-dinitrobenzoyl)-α-phenylglycinate (2) monomers were synthesized, characterized, and polymerized in chloroform using FeCl₃ as an oxidizing agent. Molecular weights of 2.6 × 10⁴ and 3.2 × 10⁴ for poly1 and poly2, respectively, were determined by SEC analysis. FTIR spectra of the polymers indicated the coupling of monomers through the α positions. UV-vis spectra showed absorption bands at λ_max = 226 and 423 nm for poly1 and poly2, ascribed to transitions of side groups and polythiophene backbone, respectively. Poly1 and poly2 remained stable up to 210 °C. At higher temperatures, a two step weight loss degradation process was observed for both polymers by TGA analysis. ¹H NMR, in the presence of Eu(tfc)₃, and optical rotation measurements indicate the chiral properties of the monomers 1 ([α]_D²⁸ = −76.2) and 2 ([α]_D²⁸ = +76.0), and the maintenance of chirality after polymerization (poly1 [α]_D²⁸ = −29.0 and poly2 [α]_D²⁸ = +28.4, c = 2.5 in THF). According to scanning electron microscopic analysis, the polymers are highly porous.     

Approaches to bi- and trimetallic platinum and palladium complexes using the DPPEPM ligand

Bis{(diphenylphosphinoethyl)phenylphosphino}methane (DPPEPM) reacts with [PtR₂(cod)] in 1:1 ratio to give [PtR₂(DPPEPM-PP)] (2a, R=Me; 2b, R=Ph), whereas with [PtCl₂(cod)] or [PdCl₂(cod)] it yields the ionic species [M(DPPEPM-PP)₂]²⁺ (3 and 4). With [MClMe(cod)], the product is [MMe(DPPEPM-PPP)]⁺ (5, M=Pt; 6, M=Pd), in which one of the internal P atoms of the ligand is uncoordinated. These complexes undergo oxidation of the free P atom to give 7 and 8 on standing in solution. Complexes 2–4 may be used to construct bimetallic and trimetallic mixed metal complexes. The molecular structures of 7 and [PtMe₂(μ-DPPEPM)PdCl₂] (11) are reported.     

Synthesis and properties of polyacetylenes carrying N-phenylcarbazole and triphenylamine moieties

Novel acetylene monomers containing N-phenyl-substituted carbazole (Cz) and triphenylamine (TPA) groups, namely, 3-ethynyl-9-phenylcarbazole (1) and p-(N,N-diphenylamino)phenylacetylene (2) were synthesized, and polymerized with several Rh-, W-, and Mo-based catalysts. Poly(1) and poly(2) with high number-average molecular weights (15?500-974?000) were obtained in good yields (77-97%), when [(nbd)RhCl]₂-Et₃N (nbd = norbornadiene) was used as a catalyst. The polymers exhibited UV-vis absorption peaks derived from the Cz and TPA moieties at 250-350 nm and polyacetylene backbone above 350 nm. The UV-vis absorption band edge wavelengths of the polymers were longer than those of the corresponding monomers. Poly(2) exhibited a UV-vis absorption peak at a longer wavelength than poly(1) did, which indicates that poly(2) has main chain conjugation longer than that of poly(1). The molecular weights and photoluminescence quantum yields of the polymers obtained by the polymerization using [(nbd)RhCl]₂-Et₃N were larger than those of the Rh⁺(nbd)[η⁶-C₆H₅B⁻(C₆H₅)₃]-based counterparts. The cyclic voltammograms of the polymers indicated that they had clear electrochemical properties; the onset oxidation voltage of poly(1) was higher than those of N-alkyl-substituted Cz derivatives. The polymers showed electrochromism and changed the color from pale yellow to blue by application of voltage, presumably caused by the formation of charged polaron at the Cz and TPA moieties. The temperatures for 5% weight loss of the polymers were around 350-420 °C under air, indicating the high thermal stability.     

Synthesis, light emission, and photo-cross-linking of luminescent polyacetylenes containing acrylic pendant groups

New poly(1-phenyl-1-alkyne)s bearing acrylic pendants (-{(C₆H₅)CC[(CH₂)_mOCOCHCH₂]}_n-; P1(m), m=3, 9) with high molecular weights are synthesized in high yields by WCl₆-Ph₄Sn catalyst. The structures and properties of P1(m) are characterized and evaluated by IR, NMR, TGA, UV, and PL analyses. All the polymers are solution-processable and thermally stable (T_d≥380 °C). Upon photoexcitation, the polymers emit strong blue lights with emission efficiencies (>40%) comparable to that of poly(1-phenyl-1-octyne), an emissive disubstituted polyacetylene. No excimeric absorption and emission are observed in the thin films of the polymers. The acrylic moieties of P1(m) are readily cross-linked by UV irradiation without harming their optical properties, which may enable them to find high-tech applications in photoresist, luminescent patterning, and light-emitting diodes.     

Synthesis of novel poly(diphenylacetylene)s with both trimethylsilyl and alkyl groups: The effect of desilylation on gas permeability

Diphenylacetylenes having both a trimethylsilyl group and an alkyl group at para positions [Me₃SiC₆H₄CCC₆H₄R; R = Et (1a), n-Bu (1b), t-Bu (1c), n-C₈H₁₇ (1d)] and having only an alkyl group [PhCCC₆H₄R; R = n-Bu (1B), n-C₈H₁₇ (1D)] were synthesized and then polymerized with TaCl₅/n-Bu₄Sn catalyst to provide the corresponding poly(diphenylacetylene)s (2a, 2b, 2c, 2d, 2B, and 2D). The formed polymers except 2c afforded tough free-standing membranes by casting from toluene solutions. Desilylation reaction of the Si-containing polymer membranes (2a, 2b, 2d) was carried out with trifluoroacetic acid, and the desilylated polymer membranes (3a, 3b, 3d) were obtained. The permeability to O₂, N₂, and CO₂ were determined for the obtained polymer membranes. All the desilylated membranes showed lower gas permeability than the Si-containing counterparts. To clarify the effects of the desilylation further, CO₂ diffusivity, CO₂ solubility, and fractional free volume (FFV) of the polymer membranes were investigated. The FFV and CO₂ diffusivity decreased upon desilylation, while CO₂ solubility hardly varied.     

Tyrosine-based poly(m-phenyleneethynylene-p-phenyleneethynylene)s. Helix folding and responsiveness to a base

The Sonogashira-Hagihara polymerization of 3′,5′-diiodo-N-α-tert-butoxycarbonyl-l-tyrosine methyl ester (1) and 3′,5′-diiodo-N-α-tert-butoxycarbonyl-O-methyl-l-tyrosine methyl ester (2) with para-diethynylbenzene (3) was carried out to obtain optically active poly(m-phenyleneethynylene-p-phenyleneethynylene)s [poly(1) and poly(2)] with M_n’s ranging from 9900 to 15,000 in 80-87% yields. Poly(1) exhibited intense CD signals in DMSO and THF, but did not in CH₂Cl₂, indicating that it took a predominantly one-handed helical conformation in the former two solvents. On the other hand, there was no evidence for poly(2) to take a helical structure in these solvents. Poly(1) turned the CD sign at 390 nm from plus to minus in DMSO/H₂O = 9/1 (v/v) by the addition of NaOH. Alkaline hydrolysis of ester moieties of poly(1) and poly(2) gave the corresponding polymers having carboxy groups [poly(1a) and poly(2a)]. Poly(1a) and poly(2a) increased the CD intensity by the addition of NaOH.     

Synthesis, characterization, and high gas permeability of poly(diarylacetylene)s having fluorenyl groups

Diarylacetylenes having fluorenyl groups and other substituents (trimethylsilyl, t-butyl, bromine, fluorine) (1a-1) were polymerized with TaCl₅-n-Bu₄Sn. Monomers 1a-l produced high molecular weight polymers 2a-l (M_w 5.1 × 10⁵-1.3 × 10⁶) in 12-59% yields. All of the polymers were soluble in common organic solvents, and gave tough free-standing membranes by the solution casting method. The onset temperatures of weight loss of polymers 2a-l in air were over 400 °C, indicating considerably high thermal stability. All the polymer membranes showed high gas permeability; e.g., the oxygen permeability coefficient (PO₂) of 2a was as large as 4800 barrers. Membrane 2d possessing two fluorine atoms at meta and para positions of the phenyl ring showed the highest oxygen permeability (PO₂ = 6600 barrers) among the present polymers.