Photocatalytic mineralisation of organic compounds: a comparison of flame-made TiO2 catalysts

A comparative photocatalytic analysis was carried out on TiO₂ made in a Flame Spray Pyrolysis (FSP) process and flame-made Degussa P25. Both have similar crystallinity, phase composition, phase segregation and a non-porous surface. Hence comparison was made based on their difference in specific surface area, organic adsorption and the amount of OH• generated upon illumination. The photocatalytic activity tests were carried out using the following series of organic compounds: sucrose, glucose, fructose, maleic acid, glyoxylic acid, oxalic acid, isobutyric acid, phenol and methanol. FSP-made TiO₂ outperformed P25 for saccharides mineralisation, while for phenol and methanol mineralisation P25 was better than FSP-made TiO₂. Similar mineralisation rates were observed for both FSP-made and P25 TiO₂ for the mineralisation of carboxylic acids. This shows that the relative performance of the photocatalysts depends on the type of organic compounds to be degraded. The high surface area and possibly a more efficient interfacial charge transfer of FSP-made TiO₂ provided an efficient pathway for saccharides mineralisation. As for phenol and methanol, the mineralisation rates were higher when using P25 due to the greater amount of OH• radicals generated by this photocatalyst. The fast mineralisation rates of carboxylic acids made degradation of these organic compounds to be less affected by the TiO₂ photocatalyst properties and conditions tested in this work.     

Photocatalytic degradation of methylene blue with TiO2 nanoparticles prepared by a thermal decomposition process

The generation of TiO₂ nanoparticles by the thermal decomposition of titanium tetraisopropoxide (TTIP) was carried out experimentally using a tubular electric furnace at various synthesis temperatures (700-1300 °C) and TTIP heating temperatures (80-110 °C). The photocatalytic activity of the resulting TiO₂ nanoparticles was examined by measuring the rate of methylene blue decomposition. The TiO₂ nanoparticles were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) measurements and transmission electron microscopy (TEM). The crystallite size and crystallinity increased with increasing synthesis temperature and TTIP heating temperature. A TTIP heating temperature and synthesis temperature of 95 °C and 900 °C, respectively, were found to be the optimal synthesis conditions. The primary particle diameter obtained under optimum synthesis conditions was considerably smaller than the commercial photocatalyst (Degussa, P25). The specific surface areas were more than 134.4 m² g^− 1. Under the optimal conditions, the photocatalytic activity for methylene blue was higher than that of the commercial photocatalyst.     

One-pot solvothermal synthesis of carbon dots/Ag nanoparticles/TiO2 nanocomposites with enhanced photocatalytic performance

In this paper, we reported a “green” and facile method for one-pot solvothermal synthesis of carbon dots (CDs)/Ag nanoparticles (AgNPs)/titanium dioxide (TiO₂, commercial Degussa P25) ternary nanocomposites with enhanced photocatalytic performance. The characterizations of this ternary photocatalyst were studied at length and our results revealed that the crystalline phase of TiO₂ component remained unchanged after the reaction. While the newborn AgNPs and CDs were tightly attached onto the surface of TiO₂ nanoparticles. The photocatalytic activities of photocatalysts were tested by measurements of photo-degradation on methylene blue (MB) under ultraviolet (UV) and visible light. It was showed that the photocatalytic performance of the ternary photocatalyst was superior to that of single TiO₂ or CDs/TiO₂ binary photocatalyst. It was probably attributed to the synergistic effect of the photoelectrical properties of CDs and the surface plasmon resonance (SPR) effect of AgNPs, which could both enhance the absorption of visible light and hinder the recombination of photogenerated electron-hole pairs.     

Effect of TiO2 nanoparticles on the antibacterial and physical properties of polyethylene-based film

TiO₂ nanoparticles and their application in packaging systems have attracted a lot of attention because of its antimicrobial activity. In this work, effect of TiO₂ nanoparticles on the antibacterial and physical properties of polyethylene (PE)-based film was investigated. Results indicated that the antibacterial activity of TiO₂-incorporated PE films should be due to the killing effect property of TiO₂ nanoparticles against microorganisms. The TiO₂-incorporated PE film exhibited more effective antibacterial activity for Staphylococcus aureus. The antibacterial activity to inactivate Escherichia coli or S. aureus was improved by UV irradiation. The inhibition ratio of TiO₂-incorporated PE films sample irradiated for 60 min by UV light was improved significantly, which were 89.3% for E. coli and 95.2% for S. aureus, respectively, compared to that of TiO₂-PE film without UV irradiation. The analysis of physical properties revealed that TiO₂ nanoparticles increased the tensile strength and elongation at break of PE-based film. The climate resistance of nano-TiO₂ films is greatly enhanced, compared to that of the blank PE film. Water vapor transmission increased from 18.1 to 24.6 g/m²·24 h with the incorporation of TiO₂ nanoparticles. Results revealed that PE based film incorporating with TiO₂ nanoparticles have a good potential to be used as active food packaging system.     

Preparation of TiO2 ultrafine nanopowder with large surface area and its photocatalytic activity for gaseous nitrogen oxides

TiO₂ nanopowder with a large surface area and high crystallinity was synthesized by a thermal decomposition process. The physicochemical properties of the prepared powders were examined by X-ray diffraction, transmission electron microscopy and nitrogen adsorption-desorption isotherms. The nanocrystallites of the prepared powers were considerably smaller than those of the commercial photocatalyst (Degussa, P25), and the particles had a dense polyhedral structure. In addition, the particles had a mainly disordered mesoporous structure with a pore volume that varied according to the pore size in the range of 2-20 nm. The photocatalytic activity of the prepared photocatalyst was obviously higher than that of P25 on the photodegradation of gaseous nitrogen oxides under UV_{254 + 185 nm} lamp irradiation. Above 40% relative humidity, the NO_x removal efficiency of the prepared photocatalyst was 10% higher than that of P25. Furthermore, a suitable relative humidity and longer residence time were found to enhance the photocatalytic oxidation of gaseous nitrogen oxides by UV_{254 + 185 nm} lamp irradiation and TiO₂ nanoparticles.     

Photocatalytic activity of TiO2 coated porous silica beads on degradation of cumene hydroperoxide

Recently, due to an increasing global concern on environmental safety, titanium dioxide (TiO₂) photocatalyst has been extensively researched for use as air and water pollution treatments. This study was initiative for producing an economically viable TiO₂ photocatalyst material with recyclability for degradation of CHP contaminated wastewater. TiO₂ P‐25, a well‐known photocatalyst, with a proper amount (15% w/w of CAC) was coated on porous silica beads (ECOLITE^®) by granulation technique, using high calcium aluminate cement (CAC) as a binder (EC+CAC+15% w/w TiO₂ P‐25). The experiments revealed that high concentration CHP solutions were completely degraded by EC+CAC+15% w/w TiO₂ P‐25 within 5 and 7 hours. The recyclability of EC+CAC+15% w/w TiO₂ P‐25 was evaluated by investigation the degradation activity of freshly prepared CHP solution under UV light irradiation using the repetitive photocatalyst beads for 6 runs. HPLC analyses indicated that the CHP degradation was completed in the 1^st run and down to over 90% in the 6^th run. Hence, EC+CAC+15% w/w TiO₂ P‐25 showed a long durability and good recyclability for CHP degradation, resulted from the good adherence of hydration product layer of CAC for TiO₂ particles as well as its large surface area that offered good adsorption for CHP.     

Changes in the chemical composition of V2O5-loaded CVC-TiO2 materials with calcination temperatures for NH3-SCR of NOx

In this study, the aim was to evaluate the effect of calcinations temperature on the catalytic activity and chemical composition of V₂O₅/TiO₂. We prepared V₂O₅-loaded CVC-TiO₂ catalysts by a combination of chemical vapor condensation (CVC) and impregnation method at different calcination temperatures. These catalysts were analyzed for their ability to catalyze NH₃-based selective catalytic reduction of NO_x. Compared with V₂O₅ loaded P25-TiO₂ (commercial). V₂O₅/CVC-TiO₂ catalysts calcined above 200 °C exhibited better performance towards NO_x conversion than that by a commercial catalyst prepared using P25-TiO₂ (calcined at 500 °C). In addition, the NO_x conversion rate obtained with the sample calcined at 500 °C gave the best result (90 %) at a reaction temperature of 200 °C. From the XPS results, we observed that the V^4+/5+ ratio was well balanced when the V₂O₅ loaded CVC-TiO₂ sample was calcined at 500 ºC.     

Preparation of TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> composite oxide and its photocatalytic degradation of rhodamine B

The composite semiconductor photocatalyst TiO₂/SiO₂ was prepared by template-hydrothermal method using carbon spheres as the template. The structural and optical properties of TiO₂/SiO₂ were characterized by XRD, SEM, BET, UV–Vis DRS, TG-DTA, PL techniques. The formation of hydroxyl radical on the surface of TiO₂/SiO₂ was studied with terephthalic acid as the probe molecule, combined with fluorescence technique. The results showed that the specific surface area of TiO₂/SiO₂ composite was 327.9 m²/g, and the specific surface area of TiO₂/SiO₂ was larger than that of pure TiO₂. Photocatalytic degradation of rhodamine B showed that TiO₂/SiO₂ composite oxide under visible light illumination 40 min, the degradation rate was 98.6 % and the degradation rate of pure TiO₂ was only 11.9 %. The apparent first-order rate constant of TiO₂/SiO₂ was 33 times that of pure TiO₂ and more than 6 times that of P25 when the molar ratio of Ti to Si was 1:1 under visible light irradiation. Moreover, it’s also as much as 5 times that of pure TiO₂ and is more than 1 times that of P25 under UV light irradiation 25 min. Based on the experimental results, ^·O₂ ^? and h⁺ were suggested to be the major active species which was responsible for the degradation reaction. The increased photocatalytic activity of TiO₂/SiO₂ may be mainly attributed to effectively suppressing the recombination of hole/electron pairs. After the photocatalyst TiO₂/SiO₂ was reused 5 times, the degradation rate of rhodamine B could reach 89.2 % under visible light irradiation. Moreover, The composite semiconductor photocatalyst TiO₂/SiO₂ was selective towards the degradation of rhodamine B.     

Photocatalytic decomposition of 2-propanol in air by mechanical mixtures of TiO2 crystalline particles and silicalite adsorbent: The complete conversion of organic molecules strongly adsorbed within zeolitic channels

Fundamental photocatalytic behaviors were investigated for mechanical mixtures of TiO₂ crystalline particles (P25) and MFI type zeolite (silicalite) in the decomposition reaction of 2-propanol vapor in air for the first time. Mechanical mixing enables reliable comparisons to be made between photocatalysts because the contents of TiO₂ and the adsorbent can be widely varied (51 times in this study) while keeping the particle size and crystallinity of TiO₂ unchanged. That is, the use of mechanical mixture highlights the behavior of molecules adsorbed in the microporous crystals, keeping the TiO₂ unchanged. In the case of the mixed photocatalysts, the initial 2-propanol concentration in the gas phase was significantly reduced because of adsorption into the zeolite. After photo-irradiation started, 2-propanol was decomposed to CO₂ with no (or trace amount of) acetone detected in the gas phase. The analysis of final amount of CO₂ formed by the decomposition demonstrated that just by the mechanical mixing of TiO₂ and zeolite, the TiO₂ photocatalyst decomposed completely the reactant and intermediate molecules strongly adsorbed into the zeolite. On the other hand, in reference experiments in which TiO₂ and zeolite were not mixed and were separately placed in a photoreactor, the organic compounds strongly adsorbed in the zeolite could not be decomposed to CO₂ by the photocatalyst. It is notable that the CO₂ formation rates for the mixed photocatalysts were mostly constant for those comprising 40 wt% or larger amounts of zeolite, while being slower than for pure TiO₂. The rate-determining step was discussed based on these data. The present study showed that the mixed photocatalyst could remove organic vapors by adsorption in the dark and decompose completely to CO₂ at moderate reaction rates under photo-irradiation with minimized evolution of intermediate molecules into the gas phase.     

High Performance Photocatalysts Based on N-doped Graphene-P25 for Photocatalytic Reduction of Carbon Tetrachloride

Carbon tetrachloride (CCl₄) is a kind of toxic and persistent groundwater contaminant. Considering keeping drinking water safe, a novel kind of N-doped graphene (NGS)-P25 TiO₂ photocatalyst was prepared by a facile one-step hydrothermal method for the removal of CCl₄ from contaminated water. Simultaneously, nitrogen-doping and the reduction of graphene oxide, and loading of P25 were finished during the same process. The photocatalytic efficiency of resulted NGS-P25 nanoparticles was studied for the degradation of CCl₄. The results indicated that NGS-P25 exhibited the highest photocatalytic activity under UV light irradiation, outperforming graphene-P25, bare P25 or NGS. The effects of NGS-P25 dosage, irradiation time, CCl₄ concentration and pH on CCl₄ photocatalytic degradation efficiency were discussed in detail. Accordingly, the optimum experimental conditions were obtained. Moreover, the high performance photocatalyst of NGS-P25 can be extended to environmental pollution control and remediation towards various pollutants.     

Fabrication of TiO2‒Ag nanocomposite thin films via one-step gas-phase deposition

In this work, TiO₂‒Ag nanocomposite thin films were fabricated for the first time via simultaneous plasma-enhanced chemical vapor deposition and physical vapor deposition of TiO₂ and Ag nanoparticles in the gas-phase, respectively. The presence of Ag nanoparticles in the prepared nanocomposites has been confirmed using transmission electron microscopy and energy dispersive X-ray spectrometry techniques. The obtained electron microscopy images showed that the average size of TiO₂‒Ag nanoparticles was larger than that of pristine TiO₂. Moreover, the temperature of the anatase transformation into the rutile phase was decreased due to the presence of Ag nanoparticles in the TiO₂ matrix, while the photocatalytic activity of the produced nanocomposite (estimated by studying the degradation of methylene blue aqueous solution under UV irradiation) was 35% greater than that of pristine TiO₂. Therefore, the addition of Ag nanoparticles into the TiO₂ matrix significantly affected the morphology, phase transformation temperature, and photocatalytic performance of the fabricated material.     

Preparation of TiO2-loaded nanocapsules and their sun protection behaviors

Titanium dioxide (TiO₂) sol (TS) or TiO₂ nanoparticles with chitosan shell were encapsulated to enhance their sun protection abilities. Nanocapsules loaded with TiO₂ were evaluated for their ultraviolet (UV) absorption and UV protection rate. The effect of eicosapentaenoic acid (EPA) incorporation into the nanocapsules was examined in relation to UV absorption. The particle size of TiO₂ crystallites in TS was below 30 nm, which was considerably smaller than that of a commercial TiO₂ (P25 TiO₂) particles. In the encapsulation of TiO₂ with chitosan, the loading efficiencies of TS were higher than those of P25 TiO₂. The sizes of the nanocapsules loaded with TiO₂ particles ranged from 30 to 80 nm. The absorption range of irradiation wavelength was enlarged by the incorporation of EPA into the nanocapsules. The TS-loaded nanocapsules exhibited a high UV protection rate of up to 95% to both UV-A and UV-B.     

Preparation of photodegradable polypropylene/clay composites based on nanoscaled TiO2 immobilized organoclay

Photodegradable polypropylene (PP) composites were prepared via melting blending using PP and titanium dioxide (TiO₂) immobilized organically modified montmorillonite (organoclay). TiO₂ immobilized organoclay (TiO₂‐OMT) was synthesized by immobilizing anatase TiO₂ nanoparticles on organically modified clay via sol–gel method. The structure and morphology of TiO₂‐OMT were characterized by XRD and scanning electron microscope (SEM), which showed that anatase TiO₂ nanoparticles with the size range of 8–12 nm were uniformly immobilized on the surface of organoclay layers. Diffuse reflection UV–vis spectra revealed TiO₂‐OMT had similar absorbance characters to that of commercial photocatalyst, Degussa P25. The solid‐phase photocatalytic degradation of PP/TiO₂‐OMT composites was investigated by FTIR, DSC, GPC and SEM. The results indicated that TiO₂‐OMT enhanced the photodegradation rate of PP under UV irradiation. This was due to that immobilization of TiO₂ nanoparticles on organoclay effectively avoided the formation of aggregation, and thereby increased the interface between PP and TiO₂ nanoparticles. After 300 h irradiation, the average molecular weight was reduced by two orders of magnitude. This work presented a promising method for preparation of environment‐friendly polymer nanocomposites. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers.     

Excellent antimicrobial properties of mesoporous anatase TiO2 and Ag/TiO2 composite films

Optically transparent, crack-free, mesoporous anatase TiO₂ thin films were fabricated. The Ag/TiO₂ composite films were prepared by incorporating Ag in the pores of TiO₂ films with an impregnation method via photoreduction. The as-prepared composite films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectronic spectra (XPS) and N₂ adsorption. The release behavior of silver ions in the mesoporous composite film was also studied. Moreover, the antimicrobial behaviors of the mesoporous film were also investigated by confocal laser scanning microscopy. The antibacterial activities of the composite films were studied by a fluorescence label method using Escherichia coli (E. coli) as a model. The as-prepared mesoporous TiO₂ films showed much higher antimicrobial efficiency than that of glass and commercial P25 TiO₂ spinning film. The facts would result from the high surface area, small crystal size and more active sites for the mesoporous catalysis. After the doping of Ag, a significant improvement for the antimicrobial ability was obtained. To elucidate the roles of the membrane photocatalyst and the doped silver in the antimicrobial activity, cells from a silver-resistant E. coli were used. These results indicated that Ag nanoparticles in the mesoporous were not only an antimicrobial but also an intensifier for photocatalysis. The as-prepared mesoporous composite film is promising in application of photocatalysis, antimicrobial and self-clean technologies.     

Sulfanilic acid-modified P25 TiO2 nanoparticles with improved photocatalytic degradation on Congo red under visible light

Visible-light-induced titania/sulfanilic acid nano-composite photocatalysts were prepared and characterized by FTIR, XPS, UV-vis, XRD, and SEM. The results indicate that the formation of Ti-O-S bonds after the modification of P25 TiO₂ nanoparticles with sulfanilic acid ligands extends the photoresponse of the photocatalyst from the UV to the visible range. The photocatalytic activity of the nano-composite photocatalyst was examined by degrading Congo red under visible light, in which its effecting factors such as irradiation time, catalyst dosage, solution pH and the addition of H₂O₂, were investigated in detail. The possible mechanism of photocatalytic degradation under visible irradiation has been also presented.     

Parameter effect on photocatalytic degradation of phenol using TiO2-P25/activated carbon (AC)

P25 powder embedded and TiO₂ immobilized on activated carbon (TiO₂-P25/AC) was prepared by P25 powder modified sol-gel and dip-coated method. The photocatalysts were characterized by XRD, BET, SEM and their photocatalytic activities were evaluated through phenol degradation in a fluidized bed photoreactor. The addition of P25 in the photocatalysts could significantly enhance the photocatalytic activity, and the optimum loading of P25 was 3 g L^?1. The operating parameter results indicated that the optimum pH for phenol degradation was 5.2; the effect of air flow rate gave an optimal value of 2 L min^?1; the increasing of UV light intensity led to an increase of degradation efficiency due to more photons absorbed on the surface of the photocatalyst. The kinetics of the phenol degradation fitted well with the Langmuir-Hinshelwood kinetics model. Finally, the photocatalytic ability of TiO₂-P25/AC was reduced only 10% after five cycles for phenol degradation.     

A highly active bi-crystalline photocatalyst consisting of TiO2 (B) nanotube and anatase particle for producing H2 gas from neat ethanol

Sodium titanate nanotubes (NaTNTs) are converted into monoclinic TiO₂ (B) nanotubes by rinsing with 0.10 M HCl followed by drying at 573 K. As calcination temperature is increased to 673 K, these TiO₂ (B) nanotubes start to transform into anatase nanoparticles producing a bi-crystalline mixture consisting of TiO₂ (B) nanotubes and anatase nanoparticles. The primary particle size of the anatase particles was estimated to be around 10 nm using Scherrer equation. After being promoted with 1% Pt, this bi-crystalline material becomes a very active photocatalyst producing 20% more H₂ gas than 1% Pt/Degussa P-25 TiO₂ in the photocatalytic dehydrogenation of neat ethanol after 2 h of UV light irradiation.     

Ternary Pt@TiO2/rGO Nanocomposite to Boost Photocatalytic Activity for Environmental and Energy Use

This work explores the effect of ternary nanostructure for the enhanced photocatalytic degradation of pollutants and dyes. One-pot solvothermal-assisted approach was used for producing nanosized Pt@TiO₂ hybrid nanoparticles (NPs) decorated on reduced graphene oxide (rGO) layers. The microstructure, morphology, chemical composition, and optical absorption of the designed photocatalyst was successfully characterized (using XRD, TEM, Raman, UV–visible absorption spectra, and XPS techniques). The ternary Pt@TiO₂-rGO photocatalyst consist of monodisperse quasi-spherical Pt@TiO₂ NPs with an average size of 11 nm deposited on the rGO nanosheets. Furthermore, Pt@TiO₂-rGO was further investigated for the photodegradation of pesticide and dyes under UV and visible light. The ternary Pt@TiO₂-rGO photocatalyst proved a significant improvement on the photodecomposition of pollutants compared to hybrid Pt@TiO₂. The Pt@TiO₂-rGO photocatalyst was found to show seven- and threefold increase in the photocatalytic activity compared to TiO₂ and Pt@TiO₂ NPs, respectively which resulted from the high surface area of rGO and as well as the strong Pt/TiO₂/rGO interactions which ensured excellent properties of charge separation. On the other hand, the ternary photocatalyst exhibited very good recycle and reuse capacity up to five cycles.

     

Effect of calcination temperature on the structural properties and photocatalytic activities of solvothermal synthesized TiO2 hollow nanoparticles

TiO₂ hollow nanoparticles were prepared by the solvothermal method, calcined at different temperatures and characterized by XRD, BET, SEM, PL and FT-IR. The effects of morphology, size and calcination temperature on the photocatalytic activity of the prepared materials were discussed in detail. It was found that the calcination temperature altered the crystallinity, morphology, surface area, and the porous structure. The photocatalytic activity of the TiO₂ powders evaluated through photocatalytic degradation of gaseous acetone under UV-light irradiation, showed TiO₂ calcined at 250 °C to exhibit a higher photocatalytic activity than commercial powders (Degussa P25).     

Multifunctionality of poly(vinyl alcohol) nanofiber webs containing titanium dioxide

We prepared titanium dioxide/PVA nanocomposite fiber webs for application in multifunctional textiles by electrospinning. The morphological properties of the TiO₂/PVA nanocomposite fibers were characterized using scanning electron microscopy and transmission electron microscopy. Layered fabric systems with electrospun TiO₂ nanocomposite fiber webs were developed using various concentrations of TiO₂ and a range of web area densities, and then the UV‐protective properties, antibacterial functions, formaldehyde decomposition ability, and ammonia deodorization efficiency of the fabric systems were assessed. Layered fabric systems with TiO₂ nanocomposite fiber webs containing 2 wt% TiO₂ nanoparticles at 3.0 g m^?2 web area density exhibited an ultraviolet protection factor of greater than 50, indicating excellent UV protection. The same system showed a 99.3% reduction in Staphylococcus aureus. Layered fabric systems with TiO₂ nanocomposite fiber webs containing 3 wt % TiO₂ nanoparticles at 3.0 g m^?2 web area density exhibited a 85.3% reduction in Klebsiella pneumoniae. Titanium dioxide nanocomposite fiber webs containing 3 wt % TiO₂ nanoparticles at 3.0 g m^?2 web area density exhibited a formaldehyde decomposition efficiency of 40% after 2 h, 60% after 4 h, and 80% after 15 h under UV irradiation. The same system showed an ammonia deodorization efficiency of 32.2% under UV irradiation for 2 h. These results demonstrate that TiO₂ nanocomposite fibers can be used to produce advanced textile materials with multifunctional properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012