Polypropylene-elastomer (TPO) nanocomposites: 2. Room temperature Izod impact strength and tensile properties

Room temperature Izod impact strength was determined for polypropylene (PP)/ethylene-co-octene elastomer (EOR) blends and nanocomposites, containing organoclays based on montmorillonite (MMT), at fixed elastomer content of 30 wt% and 0-7 wt% MMT. A ratio of maleated polypropylene, PP-g-MA to organoclay of unity was used as a compatibilizer in the nanocomposites. The organoclay serves to reduce the size of the EOR dispersed phase particles and facilitates toughening. The Izod impact strength is also influenced by the molecular weight of PP, elastomer octene content, elastomer MFI in addition to MMT content. Nanocomposites based on a low molecular weight polypropylene (L-PP) containing a higher octene content elastomer showed higher impact strength at lower MMT contents compared to those based on a low octene content elastomer. The effect of elastomer octene content on impact strength of high molecular weight polypropylene (H-PP) nanocomposites is not so significant. Elastomers having a melt flow index (MFI) in the range of 0.5-1.0 showed significant improvement in the impact strength of L-PP based nanocomposites. Most H-PP/EOR blends gave ‘super-tough’ materials without MMT and maintain this toughness in the presence of MMT. The critical elastomer particle size below which the toughness is observed is reduced by decreasing the octene content of the elastomer. For the similar elastomer particle sizes in nanocomposites, the impact strength varies as H-PP > M-PP > L-PP. The tensile modulus and yield strength improved with increasing MMT content; however, elongation at break was reduced. The extruder-made TPO showed a good-balance of properties in the presence of MMT compared to reactor-made TPO having similar modulus and elastomer content.     

Polypropylene-elastomer (TPO) nanocomposites: 1. Morphology

PP/PP-g-MA/MMT/elastomer nanocomposites were prepared in a twin-screw extruder at fixed 30 wt% elastomer and 0-7 wt% MMT content. The ratio of maleated polypropylene, PP-g-MA and organoclay was maintained at 1. Elastomer particle size and shape in the presence of MMT were evaluated for three different molecular weight grades of polypropylene (PP) and five different ethylene-co-octene elastomers (EOR) with different melt flow index (MFI) and octene contents. The MMT particles are located exclusively in the PP phase in the PP/PP-g-MA/MMT/EOR nanocomposites as seen from TEM images. Injection molded nanocomposite samples show significant decreases in elastomer particle size and increases in elastomer aspect ratio and particle density compared to as-extruded or pelletized samples. The elastomer particle size decreased significantly with increased MMT content and the molecular weight of PP. Low molecular weight PP based nanocomposite showed a greater reduction in elastomer particle size compared to medium and high molecular weight PP based nanocomposites. Elastomers having MFI in the range of 0.5-1.0 gave minimum elastomer particle sizes in the PP/PP-g-MA/MMT/EOR nanocomposite. The elastomer particles were deformed during injection molding leading to an increase in their aspect ratio. The nanocomposites containing high octene content elastomer gave smaller elastomer particle size and higher elastomer aspect ratios compared to nanocomposites containing low octene content elastomer.     

Rubber‐toughened polypropylene nanocomposite: Effect of polyethylene octene copolymer on mechanical properties and phase morphology

Rubber‐toughened polypropylene (PP)/org‐Montmorillonite (org‐MMT) nanocomposite with polyethylene octene (POE) copolymer were compounded in a twin‐screw extruder at 230°C and injection‐molded. The POE used had 25 wt % 1‐octene content and the weight fraction of POE in the blend was varied in the range of 0–20 wt %. X‐ray diffraction analysis (XRD) revealed that an intercalation org‐MMT silicate layer structure was formed in rubber‐toughened polypropylene nanocomposites (RTPPNC). Izod impact measurements indicated that the addition of POE led to a significant improvement in the impact strength of the RTPPNC, from 6.2 kJ/m² in untoughened PP nanocomposites to 17.8 kJ/m² in RTPPNC containing 20 wt % POE. This shows that the POE elastomer was very effective in converting brittle PP nanocomposites into tough nanocomposites. However, the Young's modulus, tensile strength, flexural modulus, and flexural strength of the blends decreased with respect to the PP nanocomposites, as the weight fraction of POE was increased to 20 wt %. Scanning electron microscopy (SEM) was used for the investigation of the phase morphology and rubber particles size. SEM study revealed a two‐phase morphology where POE, as droplets was dispersed finely and uniformly in the PP matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3441–3450, 2006     

Phase Morphology and Mechanical Properties of Rubber-Toughened Polypropylene Nanocomposites: Effect of Elastomer Polarity

The objective of this work was to investigate the effect of elastomer polarity on phase structure and mechanical properties of PP nanocomposites. The nonpolar and polar elastomers studied were polyethylene octene (POE) and polyethylene octene grafted maleic anhydride (POEgMAH), respectively. The results from mechanical studies showed that the POEgMAH-toughened polypropylene nanocomposites have higher Izod impact strength but lower tensile and flexural properties than the unmaleated ones. X-ray diffraction (XRD) was used to characterize the formation of nanocomposites. XRD studies revealed that intercalated rubber-toughened PP nanocomposites (RTPPNC) had been successfully prepared where the macromolecule segments PP were intercalated into the interlayer space of organoclay. XRD also indicated that the incorporation of polar POEgMAH elastomers into PP nanocomposites contribute to a better intercalation effect and formed a more exfoliated combinations structure compared to POE. Scanning electron microscope (SEM) was used for the investigation of the phase morphology and rubber particle size and particle-size distribution. SEM study revealed a two-phase morphology where POE as droplets dispersed finely and uniformly in the PP matrix. The POEgMAH-toughened PP nanocomposites shows a much finer dispersion of elastomer particles than POE-toughened PP nanocomposites.     

Studies on rheology and morphology of POE/PP thermoplastic elastomer dynamically crosslinked by peroxide

An ethylene‐octene copolymer (POE)/polypropylene (PP) thermoplastic elastomer was prepared through dynamically crosslinking by 2,5‐dimethyl‐2,5‐dilbuty (Peroxy) hexane (DHBP). The effects of DHBP concentration, POE/PP ratio, melt flow index (MFI) of PP, and mixer rotation on rheology and morphology of the thermoplastic elastomer were studied. The results showed that with increasing DHBP concentration or POE content, the size of crosslinked particles as well as the melt viscosity increased. Furthermore, agglomerates or a network structure formed as the size of crosslinked particles increased. The melt viscosity also increased as MFI of PP decreased, while the size of crosslinked particles decreased under the same condition. Research on the morphology of dynamically crosslinked POE/PP thermoplastic elastomer flowing through a capillary rheometer at different shear rates show that the reprocessing had little effect on the morphology of dynamically crosslinked elastomer. J. VINYL ADDIT. TECHNOL., 2008. © 2008 Society of Plastics Engineers.     

Morphology and mechanical properties of impact modified polypropylene blends

Isotactic polypropylene (PP) has been reactively blended with various grades of an ethylene–octene copolymer (EOC) in a twin‐screw extruder. Free radical polymerization of styrene and a multifunctional acrylate during melt extrusion has resulted in an enhancement of mechanical properties over the binary blend. The reactive blend exhibits a notched Izod impact strength over 12 times that of pure polypropylene and greater than double the performance of the binary blend. Electron microscopy shows that by grafting onto the polymers, elastomer particle size and interparticle distance decrease, while particle shape becomes less spherical. The acrylate is crucial to achieve superior performance, as infrared spectra correlate an increase in graft yield to improvements in stress–strain behavior and impact strength. In addition, melt flow index (MFI) and melt strength data indicate a reduction in unwanted side reactions of polypropylene and the presence of long‐chain branching. Dynamic‐mechanical analysis reveals that the reaction promotes miscibility between polypropylene and the EOC and reduces molecular mobility at their glass‐transition temperatures. Mechanical properties, graft yield, and MFI are shown to be highly dependent upon the elastomer's concentration, density, and molecular weight, initiator and monomer concentration, as well as processing temperature. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Changes in morphology and properties by grafting reaction in PP/EOR/CaCO3 ternary composites

The phase morphology and mechanical properties of polypropylene (PP) composites containing ethylene–octene elastomer (EOR) and calcium carbonate (CaCO₃) filler were investigated by comparing the toughening effect of unmodified EOR with EOR grafted with maleic anhydride (EOR–MA). EORs of various MA contents were prepared by free‐radical grafting of MA onto the EOR backbone using a reactive extrusion process. The composite morphology was directly explored by scanning electron microscopy technique and indirectly explored by differential scanning calorimetry and dynamic mechanical analysis. Separate dispersion of the elastomer and filler particles was achieved by using unmodified EOR. Modification of EOR by maleic anhydride grafting resulted in encapsulation of the filler particles. The mechanical properties of the composites were found to depend mainly on composite morphology and composition and, to a lesser degree, on maleic anhydride concentration. The results of this study showed that when composites contained an equal or higher amount of elastomer relative to filler, a composite with a separate dispersion structure was preferred. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3557–3562, 2003     

Modeling the mechanical and thermal expansion behavior of TPO-based nanocomposites

The modulus and coefficient of thermal expansion (CTE) of polypropylene-based nanocomposites and blends were predicted using various composite theories and compared to experimental results. The Mori-Tanaka and Chow model predictions best match the previously reported experimental trends, though the Chow model underestimates the CTE in the normal direction (ND). Of the various ternary-phase approaches used to predict the modulus and CTE of thermoplastic polyolefin (TPO) nanocomposites, a multiplicative approach wherein the contribution of the clay is calculated first and the nanocomposite is then considered to be the matrix for the elastomer blend best matches the experimental trends. The models better capture the effects of the MMT than those of the ethylene-octene elastomer, EOR. A different model predicting the effect of the MMT tactoids on the experimental TPO gives rather good quantitative agreement between the predicted and experimental values of modulus and CTE for TPO nanocomposites.     

Effect of organoclay on the morphology, phase stability and mechanical properties of polypropylene/polystyrene blends

The effect of organically modified clay on the morphology, phase stability and mechanical properties of polypropylene (PP) and polystyrene (PS) blends was studied using three molecular weight grades of PP. Maleated polypropylene was used, at a PP-g-MA/organoclay ratio of 1, to preferentially promote dispersion of the organoclay in the PP matrix. The MMT content was fixed at 3 wt% based on the PP/PP-g-MA/MMT phase and the PS content was varied from 0-100 wt% in the blend. All blends were processed using a twin screw extruder. The organoclay resides in the PP phase and at the PP/PS interface. The dispersed PS particle size is significantly reduced by the presence of MMT, with maximum decrease observed for the low viscosity PP compared to its blend without MMT. The blends with MMT did not show any change in onset of co-continuity, though MMT shifts the phase inversion composition toward lower PS contents. The phase stability of the blend was significantly improved by the presence of MMT; for blends annealed at 210 °C for 2 h the dispersed phase particle size increased by as much as 10x without MMT with little change was noted with MMT present in the blend. The tensile modulus of blends improved with the addition of MMT at low PS contents. Blends based on the highest molecular weight grade PP showed increase in the tensile yield stress up to 40 wt% PS in the absence of MMT. The tensile strength at break for blend increased slightly with MMT while elongation at break and impact strength decreased in the presence of MMT. Surface energy analysis model was used to predict the orientation and equilibrium position of the clay platelet at the interface based on the surface energies.     

A new method for preparing completely exfoliated epoxy/clay nanocomposites: nano-disassembling method

Completely exfoliated epoxy/clay nanocomposites with comprehensive high performance were successfully prepared using Nano-disassembling method. In this method, nano-SiO₂ was added into the montmorillonite and epoxy mixture system as disassembler to interact with montmorillonite (MMT). By means of the strong interaction between nanoscale particles, the MMT layers were completely disassembled into elemental nanometric mono-platelets. These mono-platelets took interlacing arrangement with the disassembler particles in the resultant nanocomposites. Mechanical testing and thermal analysis results indicated that the epoxy/MMT nanocomposites prepared by the Nano-disassembling method displayed dramatic improvements in multiple properties over conventional epoxy/organo-MMT nanocomposites. At the optimal MMT content of 5 phr, tensile modulus and tensile strength increased by 64.2 and 52.3%, respectively. Flexural modulus enhanced by 7.1%, flexural strength by 14.6% and notch impact strength by 37.7%. Glass transition temperature and thermal decomposition temperature moved to higher temperatures by 10.1 and 5.7 °C, respectively.     

Effects of acid neutralization on the morphology and properties of organoclay nanocomposites formed from K+ and Na+ poly(ethylene-co-methacrylic acid) ionomers

Nanocomposites were prepared by melt blending various sodium (Na⁺) and potassium (K⁺) ionomers formed from poly(ethylene-co-methacrylic acid) and the M₂(HT)₂ organoclay formed from montmorillonite (MMT). The effects of the neutralization level of the acid groups and the precursor melt index on the morphology and properties of the nanocomposites were evaluated using stress-strain analysis, wide angle X-ray scattering (WAXS), and transmission electron microscopy (TEM) coupled with particle analysis. The aspect ratio generally increases as the neutralization level increases, except for Na⁺ ionomer nanocomposites with neutralization levels >50%. It appears from both WAXS and TEM analyses that Na⁺ ionomer nanocomposites have higher levels of MMT exfoliation and particle orientation in the flow direction than K⁺ ionomer nanocomposites. DSC results indicate that the level of crystallinity in the Na⁺ ionomers generally increases slightly with MMT addition, while the crystallinity in the K⁺ ionomers decreases slightly with MMT addition. The relative modulus of K⁺ ionomer nanocomposites increases as the degree of neutralization increases. The relative moduli of Na⁺ ionomer nanocomposites are higher than the relative modulus of K⁺ ionomer nanocomposites, likely due to the increased crystallinity of the Na⁺ ionomers and the decreased crystallinity of the K⁺ ionomers upon addition of MMT, the higher exfoliation levels measured by the aspect ratios and the particle densities, and the higher particle orientation indicated by TEM and WAXS. The relative modulus generally increases as the aspect ratio increases. The elongation at break generally decreases as the MMT content increases and as the neutralization level increases for both ionomer types. The fracture energy of most of the ionomers increases with the addition of MMT, reaches a maximum between 2.5 and 5 wt% MMT, and then decreases upon further MMT addition.     

Crystallization behaviors of polypropylene/montmorillonite nanocomposites

The isothermal crystallization kinetics of polypropylene/montmorillonite (PP/MMT) nanocomposites synthesized via intercalation polymerization were investigated by using differential scanning calorimeter and polarizing optical microscope (POM). The crystallinity of the nanocomposites decreased with the increase of the montmorillonite content, indicating that the MMT layers dispersed in the PP matrices confined the PP chains and hindered the crystallization of the PP chains. The POM photographs showed that the spherulites of the PP/MMT nanocomposites were greatly decreased in size as MMT was introduced. On the other hand, the crystallization rate increased dramatically with the increasing of MMT content. The interfacial free‐energy per unit area perpendicular to PP chains in PP/MMT nanocomposites decreased with increasing MMT content, suggesting that the MMT layers acted as heterogeneous nuclei in the nucleation of crystallization. The nucleus density increased with the increasing of MMT content, leading to a positive effect on the crystallization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1978–1985, 2002     

Polypropylene/metallocene ethylene‐octene copolymer blends with a bimodal particle size distribution: Mechanical properties and their controlling factors

Blends of polypropylene homopolymer (PP) and metallocene produced ethylene‐octene copolymer (EOR) with a bimodal particle size distribution were investigated. The aim of the work was to study the influences of EOR characteristics and its concentration on the tensile and impact properties of the blends. The matrix ligament thickness between rubber particles was measured and compared to those predicted using the theoretical models. The relationships between blend morphology and impact property were reported. It was found that the content of comonomer and molecular weight of the EOR as well as its concentration in the blends were the major factors controlling the tensile and impact properties of the blends. These factors became ineffective to impact property when the ligament thickness of the matrix was larger than the critical value (T ～0.3–0.4 μm). To achieve blends of high impact strength, the ligament thickness between rubber particles should be smaller than the critical value, and for a certain ligament thickness, EOR with high octene content and high molecular weight was preferred. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2412–2418, 2002     

Preparation of extruded melt‐mixed polypropylene/montmorillonite nanocomposites with inline monitoring

This article advances the use of an inline optical detector to monitor the disaggregation of the montmorillonite (MMT) clay tactoids during the preparation of polypropylene (PP)/MMT nanocomposites via polymer melt compounding. During the exfoliation of the tactoids their size are reduced below the minimum particle size to produce light extinction and so, the signal of the inline detector reduces as the nanosize composite is formed. The measurement is done at the transient state with the MMT clay added as a pulse with constant weight into the PP extrusion melt flow and followed by the optical detector. The data comes out as the common residence time distribution curves having its maximum intensity related to the tactoids average particle size, keeping all other variables constants. The light extinction was measured for composites with different clays (Cloisite® 15A, 30B, Na⁺, and Sintered 20A) using the same PP grafted with maleic anhydride compatibilizer. The dissaglomeration/exfoliation efficiency increases as: ‘‘Sintered 20A’’ < ‘‘Na+ clay’’ < ‘‘organo‐modified clay’’ < ‘‘organo‐modified clay + compatibilizer’’. The best result is obtained using Cloisite® 15A and Cloisite® 20A following the expected reduction of the particle size obtained during a nanocomposite melt processing. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Effect of octene content in poly(ethylene‐co‐1‐octene) on the properties of poly(propylene)/poly(ethylene‐co‐1‐octene) blends

Ethylene‐octene random copolymer (EOC) is one of the most commonly employed elastomers for PP, and as such its rubber toughening efficiency has been extensively studied. However, most existing studies employ EOC containing an octene comonomer of about 8 mol %. Therefore, in this study, we investigated the effect of EOC octene comonomer content on the morphology and thermal and mechanical properties of PP‐ethylene random copolymer (PP‐CP)/EOC (80/20 wt %/wt %) blends. It was clearly shown that the properties of the blends are significantly affected by the octene content. The rubber particle size of the blends decreased as the octene content in the EOC was increased, which was a consequence of the reduced interfacial tension between PP‐CP and EOC. Impact strength of the blends as a function of octene content displayed a brittle‐ductile transition. The tensile yield strength and modulus of the PP‐CP/EOC blends were decreased by addition of EOC, owing to incorporation of the soft EOC into the hard PP‐CP. The tensile yield strength and modulus of PP‐CP/EOC blends decreased monotonically with the octene content in the EOC. The melting temperature as well as the crystallinity of the PP‐CP phase were not affected significantly by the addition of EOC whereas a notable shift in melting and crystallization temperatures was observed for the EOC phase. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1133–1139, 2007     

Effect of montmorillonoite modification and maleic anhydride‐grafted polypropylene on the microstructure and mechanical properties of polypropylene/montmorillonoite nanocomposites

Two types of modified montmorillonite (MMT) were achieved using octadecylamine as the modifying agent by the methods of dry process and wet route. Polypropylene (PP)/MMT nanocomposites were prepared using the melt mixing technique and employing maleic anhydride‐grafted polypropylene (PP‐MA) as the compatibilizer. The modification of montmorillonite was characterized by fourier transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), and scanning electron microscope (SEM). The effect of MMT modification and PP‐MA on the microstructure and properties of PP/MMT nanocomposites was investigated by SEM, differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and polarizing microscopy. The results show that organic montmorillonite modified by wet process (WOMMT) has a large d‐spacing increment; whereas montmorillonite modified by dry process (DOMMT) shows little d‐spacing increment. Furthermore, the mechanical properties of composites incorporating WOMMT are better than that containing DOMMT. As a third component, the addition of PP‐MA benefits the formation of exfoliated structure and the dispersion of MMT in PP matrix, and hence, enhances the physical properties of the nanocomposite. With the presence of PP‐MA, the highly dispersed MMT increases the number of spherulite crystals, enhances the melting enthalpy, improves the thermal stability, and induces the desired tiny crazes more effectively. MMT increases the storage modulus (E′) and glass‐transition temperature (T_g) of PP because of the stiffness of MMT layers, but PP‐MA decreases them owing to its high melt flow index, both of which were in favor of improving the physical properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3952–3960, 2013     

Polypropylene/organically modified Sabah montmorillonite nanocomposites: Surface modification and nanocomposites characterization

The aim of the work is to extract, purify, and organically modify montmorillonite (MMT) of Lahad Datu, Sabah bentonite. The octadecylamine treated Sabah MMT (S‐OMMT) (2–8 wt%) was then melt blended with polypropylene (PP) and maleated polypropylene (PPgMAH) (10 wt%) via single screw nanomixer extruder followed by injection molding into test samples to examine the mechanical, thermal, and morphological properties of PP/S‐OMMT nanocomposites. Unmodified Sabah MMT (S‐MMT) and commercial grade MMT (Nanomer 1.30P) filled PP nanocomposites were also characterized for comparison purpose. X‐ray diffraction results showed that the interlayer spacing of S‐MMT increased after organic modification as Fourier transform infra‐red and elemental analysis evidenced the presence of octadecylamine. PP/S‐OMMT nanocomposites showed a better dispersion and strength compared to PP/Nanomer 1.30P nanocomposites due to its smaller MMT platelet size. differential scanning calorimetry and Thermogravimetry analysis revealed that the thermal stability and crystallinity of neat PP improved with the addition of all types of MMT. Dynamic mechanical analyzer showed that PP nanocomposites have higher storage modulus (E′) values than the neat PP over the whole temperature range. The new PP/S‐OMMT nanocomposites showed a comparable performance with PP/Nanomer 1.30P nanocomposites exhibiting promising future applications of S‐MMT in polymer/MMT nanocomposites. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

聚丙烯/蒙脱土纳米复合材料的制备与性能

合成了TiCl4/MgCl2/MMT插层催化剂,通过原位聚合制备了聚丙烯/蒙脱土纳米复合材料。X射线衍射结果表明:蒙脱土在聚丙烯基质中达到了纳米级分散。与纯聚丙烯(PP5004)相比,聚丙烯/蒙脱土纳米复合材料的力学性能、维卡软化点、热变形温度以及热分解温度都有所提高。     

SBS nanocomposites as toughening agent for polypropylene

The toughening of polypropylene [PP] with styrene–butadiene–styrene rubber [SBS]/montmorillonite [MMT] nanocomposites was investigated with respect to morphological, thermal, and mechanical properties. The MMT/SBS nanocomposites were prepared in an internal mixer, using an epoxidized SBS [SBSe] to investigate its effect as a compatibilizer. The MMT/SBS nanocomposite was added to PP up to 10 wt%, aiming at material toughening. Transmission electron microscopy (TEM) revealed MMT induced dispersed-phase reductions when compared to typical PP/SBS blends. In addition, changes in the PP crystallization process were observed in the presence of the nanocomposite. Surprisingly, the use of nanofiller, combined with SBSe compatibilizer agent, increased the PP impact strength by about 60%, with no reduction in the tensile module.     

Evaluation of the structure of polypropylene/montmorillonite nanocomposite by in‐line light extinction and color measurements during multiple extrusions

This work extends the method to follow in real time the reduction of the clay particle size by light extinction measurements (turbidity), obtained via an in‐line optical detector fitted at the extruder die exit, to monitor multiple extrusions of PP/MMT nanocomposites. The optical detector was calibrated and showed to follow the Mie Theory. This theory states that the transmitted light intensity decreases for suspension of particles smaller than 500 nm. Corroborating with these results, off‐line color measurements has shown that the luminosity decrease and the yellow color increases during multiple extrusions of the nanocomposites. In addition, the color difference and the yellowness indexes of the nanocomposites using organic modified montmorillonite (MMT) are higher then the MMT Na⁺ (sodium MMT) after multiple extrusions. The addition of clay to a PP matrix produced an increase in the opacity. Results from X‐ray do follow the same trend as those obtained from the in‐line light extinction measurements. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers