热带假丝酵母发酵法生产木糖醇的研究

目的利用热带假丝酵母研究发酵木糖生产木糖醇的发酵条件。方法采用摇瓶发酵对发酵生产条件,如培养基中初始木糖浓度、接种量和通气量、氮源、pH等进行优化,通过测定发酵液中木糖的残留量、木糖醇的转化率来确定适合的发酵工艺。结果通过实验得到最佳培养基条件为:初始木糖50g/L,蛋白胨5g/L,酵母粉10g/L,硫酸镁0.5g/L、磷酸二氢钾5g/L,硫酸铵1g/L;最佳发酵条件为:pH 6.0,摇瓶发酵装液量50mL/250mL,转速200 r/min,发酵温度30℃,发酵时间28h。结论优化了木糖醇的发酵工艺。     

固定化热带假丝酵母发酵氨浸稻秸水解液生产木糖醇

采用海藻酸钙固定化热带假丝酵母细胞发酵氨水浸泡稻秸半纤维素水解液生产木糖醇。为了提高木糖醇的转化率,对发酵条件进行了研究。发酵在250 mL锥形瓶中进行。向水解液中补充适量氮源和营养盐等营养物质提高了木糖醇的生产速率,但木糖醇转化率没有因此而提高。适宜的初始pH和细胞干浓度分别为4-5和1.22 g/L。在这些条件下,进行了固定化细胞重复法较高浓缩度水解液的试验。结果发现,固定化细胞能在初始木糖浓度为104.2 g/L的水解液中重复批式发酵5次,木糖醇平均得率和生产速率分别为0.737 g/g和0.533 g/(L.h)。     

酒糟酸水解液发酵生产木糖醇的研究

采用热带假丝酵母(Candida tropicalis 1779)发酵酒糟酸水解液生产木糖醇,分别利用单因素实验和正交实验考察了影响发酵效果的工艺条件。发酵在250mL摇瓶发酵瓶中进行。结果表明,当种子龄27h、接种量20mL和氮源添加量20mL时发酵效果最好。该条件下发酵液中木糖醇浓度为11.85mg/mL,木糖利用率为45.62%。发酵实验表明酒糟酸水解液作为碳源发酵生产木糖醇具有可行性。     

响应面法优化酒糟水解液发酵生产木糖醇

研究热带假丝酵母(Candida tropicalis)GIM2.7发酵酒糟水解液生产木糖醇的最佳工艺条件,提高酒糟资源的利用率。在单因素试验结果的基础上,选择主要因素接种量、装液量、有机氮源添加量进行响应面优化。结果表明,当接种量为16%、有机氮源添加量5%、装液量109 mL/250 mL时,木糖醇转化率可达到57.8%,与预测值(60.4%)相接近,说明响应面优化酒糟水解液生产木糖醇的发酵条件是有效的。     

L-鸟氨酸发酵废菌渣水解固形物回用工艺的研究

以L-鸟氨酸发酵废菌渣水解固形物为有机氮源,进行L-鸟氨酸发酵工艺条件的研究,实验结果发现最佳回用工艺条件为:水解时间20 h,水解温度90.0℃,水解液加入量6.5 g/100 m L,6.0 mol/L硫酸溶液(m L)与含水废菌渣固形物(g)之比1∶2.5。在上述条件下,L-鸟氨酸产量达到了37.47 g/L,与酵母膏为有机氮源进行的鸟氨酸发酵差异不明显,且产量稳定。     

木薯粉酒精浓醪发酵条件的优化

以木薯粉为原料进行浓醪酒精发酵,在前期优化液化糖化条件的基础上,分析了培养基成分以及温度,pH值等条件对发酵的影响。实验结果表明,在优化的液化糖化条件下进行木薯粉浓醪酒精发酵,氮源和无机盐的最适添加量为尿素0.25%(w/w),MgSO4·7H2O0.45g/L,KH2PO41.50g/L,CaCl20.20g/L,发酵最适温度为33℃,最适初始pH4.5,酵母接种量10%(v/v),发酵时间48h。在此条件下发酵成熟醪酒精浓度高达17.2%(v/v),淀粉利用率达91%。     

不同氮源种类对米根霉RM167-12发酵生产L-乳酸的影响

蔗糖糖浆水解液经模拟移动床(SMB)分离后可得到果糖液和葡萄糖液。通过以该葡萄糖液作为碳源,以不同氮源种类:硝酸铵、硫酸铵、尿素、蛋白胨和麸皮汁作比较,考察不同氮源种类对米根霉RM167-12摇瓶发酵生产L-乳酸的影响程度,确定3%(w/v)麸皮汁作为RM167-12最佳摇瓶发酵氮源,产酸量达到118.52g/L。用3%麸皮为发酵罐发酵产酸的氮源,经3次液体深层通风搅拌发酵验证,在5L发酵罐发酵L-乳酸积累量最高可达116.31g/L。     

热带假丝酵母发酵甘蔗渣水解液生产木糖醇

用超声辅助双碱(NaOH/氨水)的方法预处理酶解蔗渣,利用热带假丝酵母发酵蔗渣水解液生产木糖醇,优化发酵的工艺参数。以木糖醇质量浓度为参照指标,分别考察了种龄、接种量、木糖初始质量浓度对热带假丝发酵蔗渣水解液生产木糖醇的影响,得出种龄为26 h,接种量为10%,木糖初始质量浓度为100 g/L为发酵木糖醇最适条件。在最适条件下,热带假丝酵母菌以蔗渣酶解液为原料发酵54 h,最终木糖醇质量浓度达到62.98 g/L。结果证明,热带假丝酵母菌可以有效发酵蔗渣水解液,有一定的研究意义。     

木薯粉酒精浓醪发酵条件的优化

以木薯粉为原料进行浓醪酒精发酵,在前期优化液化糖化条件的基础上,分析了培养基成分以及温度,pH值等条件对发酵的影响.实验结果表明,在优化的液化糖化条件下进行木薯粉浓醪酒精发酵,氮源和无机盐的最适添加量为尿素0.25%(w/w),MgSO4·7H2O 0.45g/L,KH2PO4 1.50g/L,CaCl2 0.20g/L,发酵最适温度为33℃,最适初始pH4.5,酵母接种量100,6(v/v),发酵时间48h.在此条件下发酵成熟醪酒精浓度高达17.2%(v/v),淀粉利用率达91%.     

玉米秸秆水解液发酵产生物油脂试验研究

对发酵性丝孢酵母IFFI01368发酵玉米秸秆水解液产脂的培养基组成和发酵条件进行了探索,并对油脂的脂肪酸组成进行了鉴定.结果表明最佳条件为:补加4%的蔗糖,酵母膏、硫酸铵为氮源,碳氮比100:1,pH 5.5,发酵摇瓶装液量为300 mL三角瓶装玉卷秸秆水解液50 mL,时间4d.在最佳条件下于27℃、150 r/min振荡发酵培养,所得生物量为23.5 g/L,油脂含量42.7%,产脂能力为10.03 g/L.所产生物油脂的脂肪酸主要为棕榈酸、油酸和硬脂酸.     

Reliable identification of grapevine rootstock varieties using RAPD PCR on woody samples

Since grapevine ( Vitis spp .) rootstock material is being traded increasingly as disbudded woody material a lack of distinctive morphological features on such material necessitates an alternative and reliable means of identification. Methods described here were developed for rapid and efficient extraction of DNA from woody samples rich in phenolic compounds and polysaccharides, and for subsequent identification of varieties by RAPD PCR. Using these methods, and with the application of only one selected RAPD primer, we were able to differentiate sixteen rootstock varieties, including the seven varieties most commonly used in Germany. Problems commonly encountered with reproducibility of RAPD patterns were avoided by choosing primers with a dinucleotide sequence and a high G/C content that allowed a rather high annealing temperature of 45°C. Methods described here should also be useful for other horticultural crops, especially those with woody tissues rich in phenolic compounds and polysaccharides.     

An internet compendium of analytical methods and spectroscopic information for monomers and additives used in food packaging plastics

An internet website (http://cpf.jrc.it/smt/) has been produced as a means of dissemination of methods of analysis and supporting spectroscopic information on monomers and additives used for food contact materials (principally packaging). The site which is aimed primarily at assisting food control laboratories in the European Union contains analytical information on monomers, starting substances and additives used in the manufacture of plastics materials. A searchable index is provided giving PM and CAS numbers for each of 255 substances. For each substance a data sheet gives regulatory information, chemical structures, physico-chemical information and background information on the use of the substance in particular plastics, and the food packaging applications. For monomers and starting substances (155 compounds) the infra-red and mass spectra are provided, and for additives (100 compounds); additionally proton NMR are available for about 50% of the entries. Where analytical methods have been developed for determining these substances as residual amounts in plastics or as trace amounts in food simulants these methods are also on the website. All information is provided in portable document file (PDF) format which means that high quality copies can be readily printed, using freely available Adobe Acrobat Reader software. The website will in future be maintained and up-dated by the European Commission's Joint Research Centre (JRC) as new substances are authorized for use by the European Commission (DG-ENTR formerly DGIII). Where analytical laboratories (food control or other) require reference substances these can be obtained free-ofcharge from a reference collection housed at the JRC and maintained in conjunction with this website compendium.     

Aroma characterization of various apricot varieties using headspace–solid phase microextraction combined with gas chromatography–mass spectrometry and gas chromatography–olfactometry

The characterization of the aromatic profile of several apricot cultivars with molecular tracers in order to obtain objective data concerning the aromatic quality of this fruit was undertaken using headspace–solid phase microextraction (HS–SPME). Six apricot cultivars were selected according to their organoleptic characteristics: Iranien, Orangered, Goldrich, Hargrand, Rouge du Roussillon and A4025. The aromatic intensity of these varieties measured by HS–SPME–Olfactometry were defined and classified according to the presence and the intensity of grassy, fruity and apricot like notes. In the six varieties, 23 common volatile compounds were identified by HS–SPME–GC–MS. Finally, 10 compounds, ethyl acetate, hexyl acetate, limonene, β-cyclocitral, γ-decalactone, 6-methyl-5-hepten-2-one, linalool, β-ionone, menthone and (E)-hexen-2-al were recognized by HS–SPME–GC–O as responsible of the aromatic notes involved in apricot aroma and considered as molecular tracers of apricot aromatic quality which could be utilized to discriminate apricot varieties.     

Tests of potential functional barriers for laminated multilayer food packages. Part I: Low molecular weight permeants

The advent of the functional barrier concept in food packaging has brought with it a requirement for fast tests of permeation through potential barrier materials. In such tests it would be convenient for both foodstuffs and materials below the functional barrier (sub-barrier materials) to be represented by standard simulants. By means of inverse gas chromatography, liquid paraffin spiked with appropriate permeants was considered as a potential simulant of sub-barrier materials based on polypropylene (PP) or similar polyolefins. Experiments were performed to characterize the kinetics of the permeation of low molecular weight model permeants (octene, toluene and isopropanol) from liquid paraffin, through a surrogate potential functional barrier (25 μm-thick oriented PP) into the food simulants olive oil and 3% (w/v) acetic acid. These permeation results were interpreted in terms of three permeation kinetic models regarding the solubility of a particular model permeant in the post-barrier medium (i.e. the food simulant). The results obtained justify the development and evaluation of liquid sub-barrier simulants that would allow flexible yet rigorous testing of new laminated multilayer packaging materials.     

Analysis of benzo[a]pyrene in spiked fatty foods by second derivative synchronous spectrofluorimetry after microwave-assisted treatment of samples

A simple, rapid and inexpensive method has been developed for the determination of benzo[a     

The development of reference materials for paralytic shellfish poisoning toxins in lyophilized mussel. II: Certification study

This paper describes the second part of a project undertaken to develop certified mussel reference materials for paralytic shellfish poisoning toxins. In the first part two interlaboratory studies were undertaken to investigate the performance of the analytical methodology for several PSP toxins, in particular saxitoxin and decarbamoyl-saxitoxin in lyophilized mussels, and to set criteria for the acceptance of results to be applied during the certification exercise. Fifteen laboratories participated in this certification study and were asked to measure saxitoxin and decarbamoyl-saxitoxin in rehydrated lyophilized mussel material and in a saxitoxin-enriched mussel material. The participants were allowed to use a method of their choice but with an extraction procedure to be strictly followed. The study included extra experiments to verify the detection limits for both saxitoxin and decarbamoyl-saxitoxin. Most participants (13 of 15) were able to meet all the criteria set for the certification study. Results for saxitoxin.2HCl yielded a certified mass fraction of <0.07 mg/kg in the rehydrated lyophilized mussels. Results obtained for decarbamoyl-saxitoxin.2HCl yielded a certified mass fraction of 1.59+/-0.20 mg/kg. The results for saxitoxin.2HCl in enriched blank mussel yielded a certified mass fraction of 0.48 +/- 0.06 mg/kg. These certified reference materials for paralytic shellfish poisoning toxins in lyophilized mussel material are the first available for laboratories to test their method for accuracy and performance.     

Announcing a new international peer-reviewed journal:Food Science and Human Wellness now accepting manuscript submission in English

<正>We are pleased to announce the launch of a new international peer-reviewed journal-Food Science and Human Wellness,ISSN 2213-4530,which is an open access journal,produced and hosted by Elsevier B.V.on behalf of Beijing Academy of Food Sciences.Food Science and Human Wellness is an international peer-reviewed English journal that provides a forum for the dissemination of the     

Chinese CTP Market

According to Printing and Printing Equipment Industries Association of China（PEIAC）＇s statistics to the plate manufucturer in China, in 2013, the actual offset plate production has reached 346 million square meters in China. Among them, the CTP production volume was 245 million square meters, up by 11% than that of last year; the total sales of the CTP plate was 239 million square meters, up by 13%.     

Preparatory Work of Print China 2015 is Going Smoothly

正Held at Guangdong Modern International Exhibition Center,Print China 2015 will cover 7exhibition halls,besides the original Hall No.3,4,5,6,7,the newly built F zone of Hall 3 will be used too.The total area will be140,000 square meters.Hall 3:Offset and large printing equipment,package printing equipment,post press