Riprap Protection at Bridge Piers

Although riprap is the most commonly employed countermeasure against scouring around bridge piers, few studies exist of riprap performance under live-bed conditions. In this study, failure mechanisms, stability, and placement level effects for riprap at bridge piers are considered experimentally. Under clear-water conditions, riprap is subject to shear, winnowing, and edge failure. Under live-bed conditions, a fourth failure mechanism, destabilization by bed-form progression, becomes important. Destabilization by bed-form progression is dependent on the destabilizing influence of bed-form troughs as they pass the pier. Experiments were used to assess the ability of riprap stones to protect bridge piers under a wide range of flow conditions. The effects of placing the riprap layer at depth within the sediment bed, rather than level with the bed surface, were investigated also. The study showed that, as the flow velocity increases, the ability of riprap stones to protect a pier decreases asymptotically until the scour depth in the riprap layer reaches that of an equivalent unprotected pier. In addition, it was found that the deeper the placement level the less exposed the riprap was to destabilizing bed forms and the better the protection against local scour. Lowering the placement level also meant that the riprap performed better than for surface-placed layers as the flow velocity increased. The mode of riprap failure is also changed as the placement level below the bed surface is lowered. A pier riprap size-prediction equation is proposed, including a parameter to account for placement level.     

Local Scour and Riprap Stability at an Abutment in a Degrading Bed

The paper reports on an experimental investigation concerning two important issues: (1) local scour and (2) riprap stability at a 45° wing-wall abutment in a degrading river bed of noncohesive sediment. The abutment considered was short (that is abutment length/flow depth <1). From the experimental observations, no influence of abutment inclusion on bed degradation was evident, as bed profiles with and without abutment were quite identical apart from the immediate vicinity of the abutment. Total scour depth at an abutment is found to be the maximum abutment scour depth in addition to the reduction of bed elevation due to bed degradation. The maximum abutment scour depth can be estimated from the equation given by Kandasamy and Melville in their 1998 paper. For scouring time beyond 24?h, the local abutment scour depth remains independent of time. In a degrading bed, the bed forms cause edge failure of the riprap at an abutment when the dunes propagate over the riprap layer. Initially, the dune height is significant causing the maximum damage of riprap layer. As the flow velocity reduces, the resulting bed-shear stress diminishes with the degrading bed and gradually the formation of dunes ceases. An additional experiment reveals that the damaged riprap layer is significantly vulnerable against a subsequent flood accompanied by large dunes.     

Wire Gabion for Protecting Bridge Piers

As a new alternative countermeasure to riprap for scour protection around bridge piers, wire gabions were investigated experimentally for failure mechanisms, effects of significant parameters on failure and its sizing in a clear-water condition. The dominating failure mechanism was found to be a shear failure. Based on the experimental data, the controlling factors for the stability of wire gabions as a scour countermeasure at the pier are flow depth relative to pier diameter, length to thickness ratio, coverage, alignment and placement depth of wire gabions. An equation for sizing of a wire gabion is proposed in terms of Froude number and factors reflecting both the effect and limit of significant parameters. Comparison of the equation with those of ripraps shows that smaller wire gabions than ripraps provide an equivalent protection implying cost effective and improved stability.     

Reduction of Local Scour in the Vicinity of Bridge Pier Groups Using Collars and Riprap

The present study examines the use of independent and continuous pier collars in combination with riprap for reducing local scour around bridge pier groups. The efficiency of collars was studied through experiments. The data from the experiments were compared with data from earlier studies on single piers with collars and bridge pier groups without collars. The data showed that in the case of two piers in line, combination of continuous collars and riprap results in the most significant scour reduction of about 50 and 60% for the front and rear piers, respectively. In other cases for two piers in line, independent collars showed better efficiency than a continuous collar around both piers. It was also shown that efficiency of collars is more on a rectangular pier aligned with the flow than two piers in line. Experiments however, indicated that collars are not so effective in reduction of scouring around two transverse piers.     

Riprap Failure at Circular Bridge Piers

Riprap of bridge piers is placed to prevent scour and to secure the pier from failure. Riprap is therefore an addition to a pier to increase its performance against scour. The present research intends to present three basic scour mechanisms associated with circular-shaped bridge piers in rivers first, to introduce then a number of selected experiments for a range of hydraulic, geometric, and sedimentologic conditions, and finally to describe a novel procedure for assessing the safety of these river elements against failure. This procedure is based on the Shields diagram relating to sediment entrainment in a uniform and flat sediment bed subjected by a water flow. The Shields approach is extended for the presence of a circular-shaped pier that is protected by a circular-arranged riprap layer of equal size elements. The design procedure presented in the following thus reduces to the entrainment condition of a pier for equal riprap and the sediment sizes and to the Shields entrainment condition when the pier diameter degenerates to 0.     

Failure Behavior of Riprap Layer at Bridge Piers under Live-Bed Conditions

Experiments conducted under live-bed conditions show that a riprap layer at a cylindrical bridge pier will fail in either one of the following two modes: Total disintegration or embedment. The former refers to the break-up of the entire riprap layer where the stones are washed away by the flow field generated at the pier. The latter relates to the embedment of the riprap layer where it is buried in the sediment bed. The study proposes a criterion to demarcate the limiting condition between the two types of failure. It also identifies that embedment failure is a more common failure mode of riprap layer under live-bed conditions. The causes of embedment failure are twofold: (1) bed feature destabilization; and (2) differential mobility. Bed level fluctuations caused by the propagating bed features resulted in bed feature destabilization, whereas differential mobility is due to the different response of the riprap stones and bed sediments to the flow field. Experimental results also show that the riprap layer can degrade to an equilibrium level for a given flow condition. Finally, the study proposes a semiempirical equation to compute the maximum depth of riprap degradation, which occurs at the upper end of dune regime.     

Clear-Water Scour at Piers in Sand Beds with an Armor Layer of Gravels

Clear-water scour at circular and square piers, embedded in a sand bed overlain by a thin armor layer of gravels, was experimentally studied. Depending on the pier width, flow depth, armor gravel, and bed-sand sizes, three cases of scour holes at piers in armored beds were recognized. A comparison of the experimental data shows that the scour depth at a pier with an armor layer under limiting stability of the surface particles is greater than that without an armor layer for the same bed sediments, if the secondary armoring formed within the scour hole is scattered. The equations of maximum equilibrium scour depths at piers in armored beds for these cases are proposed. On the other hand, the scour depth with an armor layer is less than that without an armor layer for the same bed sediments, when the scour hole is shielded by the compact secondary armor layer.     

Effects of Inclination of Bridge Piers on Scouring Depth

For a safe design of a bridge pier footing, it is important to estimate the maximum depth of scour as accurately as possible. The aim of this experimental study is to investigate the effects of inclination of bridge piers on local scour depths around bridge piers. Single circular piers inclined toward the downstream direction were founded in a uniform bed material. Near threshold conditions were employed. The results of this study indicate that the local scour depth decreases as the inclination of the pier increases.     

Temporal Variation of Scour Depth at Nonuniform Cylindrical Piers

The paper proposes a semiempirical model to estimate the temporal development of scour depth at cylindrical piers with unexposed foundations. A cylindrical pier with a foundation is considered as nonuniform pier. The concept of primary vortex and the principle of volumetric rate of sediment transport are used to develop a methodology to characterize the rate of evolution of the scour hole at nonuniform cylindrical piers. The model also simulates the entire scouring process at nonuniform cylindrical piers having the discontinuous surface located below the initial bed level. The scouring process includes three zones; viz Zone 1 having the scouring phenomenon similar to that of a uniform pier, Zone 2 in which the scour depth remains unchanged with its value equal to the depth of the top level of foundation below the initial bed level while the dimensions of the scour hole increase, and in Zone 3 the geometry pier foundation influences the scouring process. A concept of superposition using an effective pier diameter is proposed to simulate the scouring process in Zone 3. In addition, the laboratory experiments were conducted to utilize the laboratory results for the validation of the model. The simulated results obtained from the proposed model are in good agreement with the present experimental results and also other experimental data. Also, the effect of unsteadiness of flow is incorporated in the model and the results of the model are compared with the experimental data. The model agrees satisfactorily with the experimental data.     

Probability of Exceedance Estimates for Scour Depth around Bridge Piers

Scour at a bridge pier is the formation of a hole around the pier due to the erosion of soil by flowing water; this hole in the soil reduces the carrying capacity of the foundation and the pier. Excessive scour can cause a bridge pier to fail without warning. Current predictions of the depth of the scour hole around a bridge pier are based on deterministic models. This paper considers two alternative deterministic models to predict scour depth. For each deterministic model, a corresponding probabilistic model is constructed using a Bayesian statistical approach and available field and experimental data. The developed probabilistic models account for the estimated bias in the deterministic models and for the model uncertainty. Parameters from both prediction models are compared to determine their accuracy. The developed probabilistic models are used to estimate the probability of exceedance of scour depth around bridge piers. The method is demonstrated on an example bridge pier. The paper addresses model uncertainties for given hydrologic variables. Hydrologic uncertainties have been presented in a separate paper.     

Large-Scale Flume Tests of Riprap-Apron Performance at a Bridge Abutment on a Floodplain

Laboratory tests using a large-scale model of a spill-through bridge abutment led to important findings about the performance of a riprap apron as an abutment scour countermeasure. Riprap stone is widely used for protecting side slopes of embankments against erosion, and several design guidelines are available in the literature. In contrast, only a few guidelines exist for the design of a riprap apron around an abutment. These guidelines focus only on the armoring effect of riprap, neglecting other effects. This study shows that apron performance involves several mechanisms: armoring the bed, dissipating large-scale turbulence shed from the abutment, reducing the peak unit discharge, reducing the average shear stress, and shifting the scour region away from the abutment. Together, these mechanisms substantially reduce the maximum scour depth. The test findings are compared with those from a much smaller model of riprap-apron performance.     

Design Method of Time-Dependent Local Scour at Circular Bridge Pier

A reliable prediction of local scour depth related to hydrological characteristics such as peak discharge, and time corresponding to the equilibrium scour depth is essential for the efficient design of bridge pier foundation. In this paper, a design method to predict the local scour depth with time is proposed. An experimental program was carried out using a cylindrical pier placed in uniform beds under clear-water flows. The pier scour depth was calculated on the basis of a sediment transport equation. Equilibrium local scour depth is reached when the bed-shear stress tends to critical bed-shear stress in the scour hole. Hence, changes to bed-shear stress at the circular bridge pier should be incorporated in the sediment transport theory. The proposed method follows experimental data of various sources.     

Evolution of Scour Depth at Circular Bridge Piers

Experiments of bridge pier scour are carried out under steady and unsteady clear-water scour conditions with uniform and nonuniform sediments. Around the pier nose, the sediment size variation of surface bed materials is investigated, and a regressed formula is obtained for estimating the mixing layer thickness in terms of median sediment size and geometric standard deviation of grain size distribution. A method based on the mixing layer concept is developed for calculating the equilibrium scour depth in nonuniform sediment. Based on the experimental data of scour rate, a model simulating the scour-depth evolution under steady flow in nonuniform sediment is presented. By analyzing experimental data, a scheme is proposed for computing the scour-depth evolution under unsteady flow.     

Application of Riprap and Collar to Prevent Scouring around Rectangular Bridge Piers

Various methods to control scour around bridge piers have been proposed, including application of riprap and installing a collar around piers. In the present study application of riprap alone and a combination of riprap and collar were examined experimentally for scour control around rectangular bridge piers. Piers aligned with the flow and skewed at 5, 10, and 20° to the flow were tested. Piers with three different aspect ratios equal to 1:3, 1:5, and 1:7 were used in this study. A collar three times wider than the piers’ width was installed around the piers at the streambed level. All experiments were conducted at the threshold of motion of the bed material. The size and extent of stable riprap stones for prevention of scouring around the piers was found by experiment with and without the collar. A method previously given for calculating stable riprap size around circular piers is extended for rectangular piers with different aspect ratios and skew angles with and without collar protection. The extent of stable riprap layer in all tests is also presented.     

Control of Scour at Bridge Piers by a Downstream Bed Sill

Results are presented from laboratory experiments to investigate the effectiveness of bed sills as countermeasures against local scouring at a smooth circular bridge pier, for flow conditions near the threshold of uniform sediment motion. The bed sill was located downstream of the pier, and its effectiveness with the distance between pier and sill was evaluated. The dependence of the scour depth on different dimensionless groups was defined. The results showed that a bed sill placed at a short distance downstream of the pier reduces the scour depth, area, and volume. In particular, the smaller the distance between the two structures, the larger the effectiveness of the countermeasure. The bed sill seems to take effect some time after the beginning of the test, as the scour hole downstream of the bridge pier develops sufficiently and interacts with the countermeasure.     

Case Study: Retrofitting Large Bridge Piers on the Nakdong River, South Korea

The Gupo Bridge crosses the Nakdong River near the city of Busan, South Korea. During Typhoon Maemi in 2003, the old Gupo Bridge collapsed due to excessive pier scour. More recently, the highway construction on the left-bank floodplain required right-bank channel widening to restore the channel flood-carrying capacity. This 7?m deep floodplain excavation is expected to cause significant local scour around the 8–10?m wide and 3?m thick spread footings of Piers 11 and 12 of the Subway Bridge and Piers 15 and 16 of the Gupo Bridge. Three design options are examined for retrofitting floodplain bridge piers with massive spread footings. A solution with sheet piles and riprap was recommended in 2006 as the most appropriate design, but Plan III with a conical riprap structure around the footings was ultimately constructed in 2007 for economic reasons. Laboratory experiments also highlight the need to place gravel and synthetic filters under the designed riprap.     

SRICOS: Prediction of Scour Rate in Cohesive Soils at Bridge Piers

A new method called SRICOS is proposed to predict the scour depth z versus time t around a cylindrical bridge pier of diameter D founded in clay. The steps involved are: (1) taking samples at the bridge pier site; (2) testing them in an erosion function apparatus to obtain the scour rate ? versus the hydraulic shear stress applied τ; (3) predicting the maximum shear stress τmax, which will be induced around the pier by the water flowing at vo before the scour hole starts to develop; (4) using the measured ? versus τ curve to obtain the initial scour rate ?i corresponding to τmax; (5) predicting the maximum depth of scour zmax for the pier; (6) using ?i and zmax to develop the hyperbolic function describing the scour depth z versus time t curve; and (7) reading the z versus t curve at a time corresponding to the duration of the flood to find the scour depth that will develop around that pier. A new apparatus is developed to measure the ? versus t curve of step 2, a series of advanced numerical simulations are performed to develop an equation for the τmax value of step 3, and a series of flume tests are performed to develop an equation for the zmax value of step 5. The method is evaluated by comparing predictions and measurements in 42 flume experiments.     

Effect of Sediment Size Scaling on Physical Modeling of Bridge Pier Scour

Local pier scour experiments were performed in the laboratory to investigate the effect of relative sediment size on pier scour depth using three uniform sediment sizes and three bridge pier designs at different geometric model scales. When the data from a large number of experimental and field investigations are filtered according to a Froude number criterion, the effect of relative sediment size on dimensionless pier scour depth is brought into focus. The choice of sediment size in the laboratory model distorts the value of the ratio of pier width to sediment size in comparison with the prototype which in turn causes larger values of scour depth in the laboratory than in the field. This model distortion due to sediment size is shown to be related to the scaling of the large-scale unsteadiness of the horseshoe vortex by studying the relevant time scales of its coherent structure upstream of a bridge pier using acoustic Doppler velocimeter measurements. Observations of sediment movement, probability distributions of velocity components, and phase-averaging of velocity measured upstream of a bridge pier reveal properties of coherent motions that are discussed in terms of their contribution to the relationship between dimensionless pier scour depth and the ratio of pier width to sediment size over a large range of physical scales.     

Flume Tests for Scour in Clay at Circular Piers

Local scour at circular piers founded on clay was studied experimentally in the laboratory to compare the depth of scour in sand and in clay and to investigate the effects of the Reynolds number, Froude number, and approach flow depth on scour depth. The depths of scour in front, at the side, and in the back of the piers were measured as a function of time under steady, gradually varied flow conditions. The measured scour-depth-versus-time curves were fitted with a hyperbola to estimate the equilibrium scour depths. The extrapolated equilibrium scour depths were compared with values predicted by the Federal Highway Administration equation. The results showed that although the rates of scour were much slower in clay than in sand, equilibrium scour in clay was about the same as in sand. It was found that the shape of the scour hole correlates with the pier Reynolds number. At low Reynolds numbers, the depth of scour was about the same all around the piers. At higher Reynolds numbers, the scour holes developed mainly behind the piers with much less scour in front of the piers. It was also found that the extrapolated equilibrium scour depth correlates well with the pier Reynolds number and that the Froude number and relative water depth did not have a significant effect on the scour depth for these experimental conditions.     

Bridge Pier Scour in Clay-Sand Mixed Sediments at Near-Threshold Velocity for Sand

Local scour at circular bridge piers embedded in a clay-sand-mixed bed was investigated in laboratory flume experiments. The effects of clay content, water content, and sand size on maximum equilibrium scour depth, equilibrium scour hole geometry, scouring process, and time variation of scour were studied at velocities close to the threshold velocities for the sand in the clay-sand mixture. It was observed that clay content and water content were the key parameters that effect the scouring process, scour hole geometry, and maximum equilibrium scour depth. The bridge pier scouring process in clay-sand mixtures involved different dominating modes for removal of sediment from scour hole: chunks-of-aggregates, aggregate-by-aggregate, and particle-by-particle. Regression-based equations for estimation of nondimensional maximum scour depth and scour hole diameter for piers embedded in clay-sand mixtures having clay content of <40% and water content of <40% were proposed as functions of pier Froude number, clay content, water content, and bed shear strength.