Synthesis of phospholipidated β‐cyclodextrin and its application for flame‐retardant poly(lactic acid) with ammonium polyphosphate

In this study, phospholipidated β‐cyclodextrin (PCD) was obtained by the condensation between β‐cyclodextrin and phenyl phosphonic acid dichloride, which was characterized by Fourier transform infrared (FTIR) spectra, ¹H‐NMR, and thermogravimetric analysis (TGA). The thermal stability and flame retardancy of the poly(lactic acid) (PLA) blends [PLA–ammonium polyphosphate (APP)–PCD] were measured by TGA coupled to FTIR spectroscopy, vertical burning test (UL‐94), limiting oxygen index (LOI), and cone calorimetry tests. The results show that the mass ratio and loading amount of APP and PCD affected the properties of PLA. When the loading of APP and PCD was 30 wt % and the mass ratio of APP to PCD was 5:1, the highest LOI value of 42.6% (that of neat PLA was 19.7%) and a UL‐94 V0 rating were achieved, and the reduction of the total heat release was greater than 80%. Even when the total amount of APP and PCD was decreased to 20 wt % with the same mass ratio, the flame‐retardant PLA still can achieved a UL‐94 V0 rating. The improved performance was explained by the formation of an intumescent, continuous, contact char layer. Moreover, the reaction between APP and PCD contributed to the improvement of the thermal stability of the char residue. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46054.     

Triple‐faced polypropylene: Fire retardant,thermally stable,and antioxidative

A halogen‐free nitrogen‐rich additive was used to make polypropylene (PP) prepared for three different missions: fire retardancy, thermal stability, and antioxidative properties. The prepared additive was composed of a cyclodextrin, a nanohydroxyapatite, and a poly[[6‐[(1,1,3,3,‐tetramethylbutyl)amino]‐1,3,5‐triazine‐2,4‐diyl][(2,2,6,6‐tetramethyl‐4‐piperidinyl)imino]‐1,6‐hexanediyl[2,2,6,6‐tetramethyl‐4‐piperidinyl)imino] (SABO®STAB) integrated into a unique molecule, namely, BSDH. Fire retardancy performance of BSDH in PP was compared with that of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) commercially available additive in terms of cone calorimeter results. Thermal stabilities of PP/BSDH and PP/DOPO composites were compared by changes observed in pyrolysis activation energy values measured in thermogravimetric analysis under nitrogen atmosphere at various heating rates. Flame retardancy of PP/BSDH composite was reflected in a drop in the peak of Heat Release Rate by ca. 31% with respect to neat PP. Very interestingly, the results show that BSDH additive retarded thermal oxidation of PP macromolecular chains when compared with DOPO commercially available flame retardant, as signaled by a rise in oxidation induction time value as well as an increased early‐stage activation energy needed for thermal decomposition of PP in the presence of BSDH. J. VINYL ADDIT. TECHNOL., 25:366–376, 2019. © 2019 Society of Plastics Engineers     

Synthesis of a novel flame retardant containing phosphazene and triazine groups and its enhanced charring effect in poly(lactic acid) resin

A novel flame retardant heax‐[N,N′,N″‐tris‐(2‐amino‐ethyl)‐[1,3,5] triazine‐2,4,6‐triamine] cyclotriphosphazene (HTTCP) containing phosphazene and triazine groups was synthesized and characterized by Fourier transform infrared spectroscopy (FTIR), solid‐state ¹H and ¹³C nuclear magnetic resonance (NMR) spectroscopy. HTTCP was applied to PLA matrix. The results of thermal gravimetric analysis (TGA), the limited oxygen index (LOI), and cone calorimeter test indicated that the HTTCP enhanced the thermal stability and flame retardant properties of PLA. When the mass fraction of HTTCP was 25 wt %, the PLA composite acquired a LOI value of 25.2% and the lower pk‐HRR at 290 kW/m². The excellent flame retardancy of HTTCP was attributed to the group synergistic effect between phosphazene and triazine groups. However, when combined HTTCP with APP (the total amount remaining 25 wt %, the ratio of HTTP to APP are 1:1 and 1:2), high values of LOI (over 40%) and UL94 V‐0 rating without dripping reached simultaneously. Meanwhile, the heat release rate, total heat release and mass loss rate were all decreased dramatically. Scanning electron microscopy (SEM) demonstrated that HTTCP/APP system benefited to the formation of more intumescent, dense, compact char layer on the materials surface which could effectively prevent the underlying material from degradation during burning. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44660.     

Application of a novel halogen‐free intumescent flame retardant for acrylonitrile‐butadiene‐styrene

A novel intumescent flame retardant (IFR), containing ammonium polyphosphate (APP) and poly(tetramethylene terephthalamide) (PA4T), was prepared to flame‐retard acrylonitrile‐butadiene‐styrene (ABS). The flame retardation of the IFR/ABS composite was characterized by limiting oxygen index (LOI) and UL‐94 test. Thermogravimetric analysis (TGA) and TGA coupled with Fourier transform infrared spectroscopy (TG‐FTIR) were carried out to study the thermal degradation behavior of the composite and look for the mechanism of the flame‐retarded action. The morphology of the char obtained after combustion of the composite was studied by scanning electron microscopy (SEM). It has been found the intumescent flame retardant showed good flame retardancy, with the LOI value of the PA4T/APP/ABS (7.5/22.5/70) system increasing from 18.5 to 30% and passing UL‐94 V‐1 rating. Meanwhile, the TGA and TG‐FTIR work indicated that PA4T could be effective as a carbonization agent and there was some reaction between PA4T and APP, leading to some crosslinked and high temperature stable material formed, which probably effectively promoted the flame retardancy of ABS. Moreover, it was revealed that uniform and compact intumescent char layer was formed after combustion of the intumescent flame‐retarded ABS composite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Evaluation of nonconventional additives as fire retardants on polyamide 6,6: Phosphorous‐based master batch, α‐zirconium dihydrogen phosphate,and β‐cyclodextrin based nanosponges

The influence of new types of additives, such as halogen‐ and antimony‐free flame‐retardant master batches based on phosphorus, α‐zirconium dihydrogen phosphate, and β‐cyclodextrin nanosponges, on the flame retardancy of polyamide 6,6 (PA6,6) by means of cone calorimetry and limiting oxygen index (LOI) tests was investigated. A significant decrease of the heat release rate, depending by the type of additive used, was observed. Furthermore, with the consideration that the life safety during the fire could be improved by a decrease in the fire hazard, a decrease in the quantity of the smoke and its toxicity, depending also on the type of additive, was revealed. With regard to the LOI test, neat PA6,6 showed a slight increase in the LOI value in comparison with the PA6,6 composites. However, all of the PA6,6/composites showed a slower burning velocity and antidripping effects at oxygen concentrations corresponding to the LOI value. To understand the flame‐retardancy mechanism of these novel PA6,6 composites, we thoroughly investigated their thermal decomposition behavior and microstructure/elemental analysis by scanning electron microscopy/energy‐dispersive X‐ray spectroscopy. Furthermore, the combustion behavior of these novel PA6,6 composites was compared with that of conventional nanofillers (e.g., modified montmorillonite clay and carbon nanotubes). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal degradation behavior and gas phase flame‐retardant mechanism of polylactide/PCPP blends

The thermal degradation behavior of the blend based on polylactide (PLA) and poly(1,2‐propanediol 2‐carboxyethyl phenyl phosphinate) (PCPP) was investigated by the thermogravimetric analysis (TGA). Thermal degradation activation energies (E_a) of neat PLA and PLA/15% PCPP blend were calculated via the Flynn–Wall–Ozawa method. The E_a of the blends increased with the addition of PCPP increasing when the conversion was higher than 10%. In addition, the appropriate conversion models for the thermal degradation process of PLA and PLA/15% PCPP were studied via the Criado method. At the same time, the main gaseous decomposition products of PLA and its blend were identified by TGA/infrared spectrometry (TGA–FTIR) analysis. And it revealed that the PCPP improved the flame‐retardant property of PLA via altering the release of the flammable gas and nonflammable gas. Moreover, the PCPP improved the flame‐retardant property of PLA by inhibiting exothermic oxidation reactions in the combustion, which was further proved by pyrolysis–gas chromatography–mass spectrometry analysis. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40480.     

Flame‐retardancy properties of tris(2‐hydroxyethyl) isocyanurate based charring agents on polypropylene

Tris(2‐hydroxyethyl) isocyanurate based charring agent (TBCA) was synthesized by melt polycondensation with tris(2‐hydroxyethyl) isocyanurate (THEIC) and terephthalic acid as raw materials. It was characterized by Fourier transform infrared spectroscopy, elemental analysis, ¹H‐NMR, and thermogravimetric analysis (TGA). TBCA was blended with ammonium polyphosphate (APP) to form an intumescent flame retardant (IFR) for polypropylene (PP). The charring properties of TBCA was tested by flame retardancy in the PP/APP/TBCA (PP/IFR₂) composite and compared with that of the PP/APP/THEIC (PP/IFR₁) composite. The results show that PP/IFR₂ had lower flame‐retardant properties but better water resistance than that of the PP/IFR₁ composite because PP/IFR₂ could still obtain a V‐0 rating after it had been soaked in water at 70°C for 96 h, whereas PP/IFR₁ could not achieve any rating after 36 h. Their combustion performance was further evaluated by a cone calorimeter test, their thermal degradation processes were studied by TGA, and the morphology of the char residue was observed by scanning electron microscopy. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41810.     

Behavior of α‐ and β‐cyclodextrin‐encapsulated allyl isothiocyanate as slow‐release additives in polylactide‐co‐polycaprolactone films

The natural antibacterial agent allyl isothiocyanate (AITC) encapsulated in either α‐ or β‐cyclodextrin (CD) has previously been evaluated as a slow‐release additive in polylactide‐co‐polycaprolactone (PLA–PCL) films designed for use in cheese packaging. In the research described in this article, thermogravimetric analysis (TGA) and thermogravimetric analysis in tandem with mass spectrometry (TGA–MS) were used to explore the thermal properties of CD‐encapsulated AITC complexes as well as those of PLA–PCL films containing these complexes. To our knowledge, this is the first reported application of the TGA–MS technique to explore the thermal stability of CD‐entrapped AITC and the first study to report differences in thermal stability of AITC in α‐and β‐CD cavities in the solid state. Observed differences in the thermal degradation profile of films containing the CD complexes can be explained if AITC binds more strongly to β‐CD than to α‐CD. This hypothesis has been reinforced by gas chromatography (GC) and high performance liquid chromatography (HPLC) studies, the results of which suggest that a new covalently bound AITC–CD complex may be formed when incorporating the β‐CD complex of AITC in PLA–PCL films but not when incorporating the α‐CD complex of AITC. This finding means that the α‐CD complex of AITC would be preferred in situations where adequate long‐term controlled release of AITC from polymer films is required, as for example in the case of active packaging applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis of novel triazine charring agent and its effect in intumescent flame‐retardant polypropylene

A novel charring agent (CNCA‐DA) containing triazine and benzene ring, using cyanuric chloride, aniline, and ethylenediamine as raw materials, was synthesized and characterized. The effects of CNCA‐DA on flame retardancy, thermal degradation, and flammability properties of polypropylene (PP) were investigated by limited oxygen index (LOI), vertical burning test (UL‐94), thermogravimetric analysis (TGA), and cone calorimeter test (CCT). The TGA results showed that CNCA‐DA had a good char forming ability, and a high initial temperature of thermal degradation; the char residue of CNCA‐DA reached 18.5% at 800°C; Ammonium polyphosphate (APP) could improve the char residue of APP/CNCA‐DA system, the char residue reached 31.6% at 800°C. The results from LOI and UL‐94 showed that the intumescent flame retardant (IFR) containing CNCA‐DA and APP was very effective in flame retardancy of PP. When the mass ratio of APP and CNCA‐DA was 2 : 1, and the IFR loading was 30%, the IFR showed the best effect; the LOI value reached 35.6%. It was also found that when the IFR loading was only 20%, the flame retardancy of PP/IFR can still pass V‐0 rating in UL‐94 tests, and its LOI value reached 27.1%. The CCT results demonstrated that IFR could clearly change the decomposition behavior of PP and form a char layer on the surface of the composites, consequently resulting in efficient reduction of the flammability parameters, such as heat release rate (HRR), total heat release (THR), smoke production rate (SPR), total smoke production (TSP), and mass loss (ML). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of a novel phosphorus‐containing compound on the flame retardancy and thermal degradation of intumescent flame retardant polypropylene

A novel flame retardant, tetra(5,5‐dimethyl‐1,3‐ dioxaphosphorinanyl‐2‐oxy) neopentane (DOPNP), was synthesized successfully, and its structure was characterized by FT‐IR, ¹H NMR, and ³¹P NMR. The thermogravimetric analysis (TGA) results demonstrate that DOPNP showed a good char‐forming ability. Its initial decomposition temperature was 236.4°C based on 1% mass loss, and its char residue was 41.2 wt % at 600°C, and 22.9 wt % at 800°C, respectively. The flame retardancy and thermal degradation behavior of novel intumescent flame‐retardant polypropylene (IFR‐PP) composites containing DOPNP were investigated using limiting oxygen index (LOI), UL‐94 test, TGA, cone calorimeter (CONE) test, and scanning electron microscopy (SEM). The results demonstrate that DOPNP effectively raised LOI value of IFR‐PP. When the loading of IFR was 30 wt %, LOI of IFR‐PP reached 31.3%, and it passed UL‐94 V‐0. TGA results show that DOPNP made the thermal decomposition of IFR‐PP take place in advance; reduced the thermal decomposition rate and raised the residual char amount. CONE results show that DOPNP could effectively decrease the heat release rate peak of IFR‐PP. A continuous and compact char layer observed from the SEM further proved the flame retardance. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Preparation and investigation of flame‐retardant epoxy resin modified with a novel halogen‐free flame retardant containing phosphaphenanthrene,triazine‐trione,and organoboron units

In this article, a novel flame retardant (coded as BNP) was successfully synthesized through the addition reaction between triglycidyl isocyanurate, 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide and phenylboronic acid. BNP was blended with diglycidyl ether of bisphenol‐A to prepare flame‐retardant epoxy resin (EP). Thermal properties, flame retardancy, and combustion behavior of the cured EP were studied by thermogravimetric analysis, limited oxygen index (LOI) measurement, UL94 vertical burning test, and cone calorimeter test. The results indicated that the flame retardancy and smoke suppressing properties of EP/BNP thermosets were significantly enhanced. The LOI value of EP/BNP‐3 thermoset was increased to 32.5% and the sample achieved UL94 V‐0 rating. Compared with the neat EP sample, the peak of heat release rate, average of heat release rate, total heat release, and total smoke production of EP/BNP thermosets were decreased by 58.2%–66.9%, 27.1%–37.9%, 25.8%–41.8%, and 21.3%–41.7%, respectively. The char yields of EP/BNP thermosets were increased by 46.8%–88.4%. The BNP decomposed to produce free radicals with quenching effect and enhanced the charring ability of EP matrix. The multifunctional groups of BNP with flame retardant effects in both gaseous and condensed phases were responsible for the excellent flame retardancy of the EP/BNP thermosets. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45291.     

Influence of ammonium polyphosphate modified with 3‐(methylacryloxyl) propyltrimethoxy silane on mechanical and thermal properties of wood flour–polypropylene composites

In this article, the influence of ammonium polyphosphate (APP) and ammonium polyphosphate modified with 3‐(Methylacryloxyl) propyltrimethoxy silane (M‐APP) on mechanical properties, flame retardancy, and thermal degradation of wood flour–polypropylene composites (WF/PP composites) have been investigated. Polypropylene grafted with m‐isopropenyl‐α,α‐dimethylbenzyl‐isocyanate (m‐TMI‐g‐PP) was used to improve the adhesion of WF/PP composites. APP and M‐APP were used as flame retardants. The experimental results demonstrated that addition of M‐APP obviously enhanced mechanical properties of WF/PP composites. According to cone calorimetry results, M‐APP is also an effective flame retardant for WF/PP composites, compared to that of APP. It was also found that M‐APP decreased the 1% weight loss temperature and increased char residue. The thermal degradation of wood flour based upon the first peak temperature of wood decreased from 329.3 to 322.9°C and the thermal degradation of PP based upon the second peak temperature of PP improve from 518.0 to 519.6°C, when M‐APP was added to the WF/PP composites. From SEM results the char layer of the 25% M‐APP systems is much more intumescent than that of the 25% APP systems, indicating that 3‐(Methylacryloxyl) propyltrimethoxy silane can improve the char‐forming ability of WF/PP composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polyamide‐enhanced flame retardancy of ammonium polyphosphate on epoxy resin

An attractive intumescent flame retardant epoxy system was prepared from epoxy resin (diglycidyl ether of bisphenol A), low molecular weight polyamide (cure agent, LWPA), and ammonium polyphosphate (APP). The cured epoxy resin was served as carbonization agent as well as blowing agent itself in the intumescent flame retardant formulation. Flammability and thermal stability of the cured epoxy resins with different contents of APP and LWPA were investigated by limited oxygen index (LOI), UL‐94 test, and thermogravimetric analysis (TGA). The results of LOI and UL‐94 indicate that APP can improve the flame retardancy of LWPA‐cured epoxy resins. Only 5 wt % of APP can increase the LOI value of epoxy resins from 19.6 to 27.1, and improve the UL‐94 ratings, reaching V‐0 rating from no rating when the mass ratio of epoxy resin to LWPA is 100/40. It is much interesting that LOI values of flame retardant cured epoxy resins (FR‐CEP) increase with decreasing LWPA. The results of TGA, FTIR, and X‐ray photoelectron spectroscopy (XPS) indicate that the process of thermal degradation of FR‐CEP consists of two main stages: the first stage is that a phosphorus rich char is formed on the surface of the material under 500°C, and then a compact char yields over 500°C; the second stage is that the char residue layer can give more effective protection for the materials than the char formed at the first stage do. The flame retardant mechanism also has been discussed according to the results of TGA, FTIR, and XPS for FR‐CEP. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of ammonium polyphosphate and triphenyl phosphate on the flame retardancy,thermal, and mechanical properties of glass fiber–reinforced PLA/PC composites

The purpose of this study is to increase of the flammability properties of the glass fiber (GF)–reinforced poly (lactic acid)/polycarbonate (PLA/PC) composites. Ammonium polyphosphate (APP) and triphenyl phosphate (TPP) were used as flame retardants that are including the organic phosphor to increase flame retardancy of GF‐reinforced composites. APP, TPP, and APP‐TPP mixture flame retardant including composites were prepared by using extrusion and injection molding methods. The properties of the composites were determined by the tensile test, limiting oxygen index (LOI), differential scanning calorimetry (DSC), and heat release rate (HRR) test. The minimum T_g value was observed for the TPP including PLA/PC composites in DSC analysis. The highest tensile strength was observed in GF‐reinforced PLA/PC composites. In the LOI test, GF including composite was burned with the lowest concentration of oxygen, and burning time was the longest of this composite. However, the shortest burning time was obtained by using the mixture flame retardant system. The flame retardancy properties of GF‐reinforced PLA/PC composite was improved by using mixture flame retardant. When analyzed the results of HRR, time to ignition (TTI), and mass loss rate together, the best value was obtained for the composite including APP.     

Modification of lignin and its application as char agent in intumescent flame‐retardant poly(lactic acid)

Urea‐modified lignin was prepared according to the Mannich reaction and well characterized by Fourier transform infrared spectrometer, elemental ananlyses, and scanning electron microscopy (SEM). Ammonium polyphosphate (APP) and urea‐modified lignin were added into poly(lactic acid) (PLA) as a novel intumescent flame‐retardant (IFR) system to improve flame retardancy of PLA. The flammability of IFR–PLA composites was studied using limiting oxygen index, UL‐94 vertical burning method and cone calorimeter test, and their thermal stability was evaluated by thermogravimetric analysis. The results showed that the urea‐modified lignin combined with APP exhibited much better flame retardancy and thermal stability than that of the combination of virgin lignin and APP. The improvement may be attributed to the better char morphology with more phosphoric char evidenced by SEM and X‐ray photoelectron spectroscopy. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Influence of ammonium polyphosphate on the flame retardancy and mechanical properties of ramie fiber‐reinforced poly(lactic acid) biocomposites

Fully degradable natural fiber/degradable polymer composites have received much research attention and have various applications such as in automotive components. But flammability limits their application; it is important to improve the flame retardancy of fully degradable composites with environmentally friendly flame retardants. Flame‐retarded ramie fiber‐reinforced poly(lactic acid) (PLA) composites were prepared using three processes: (1) PLA was blended with ammonium polyphosphate (APP), and then the resulting flame‐retarded PLA was combined with ramie fibers; (2) ramie fibers underwent flame‐retardant treatment with APP, which were then compounded with PLA; and (3) PLA and ramie, both of which had been flame‐retarded using APP, were blended together. The APP in the composites is shown to be very effective in improving flame retardancy according UL94 test and limiting oxygen index measurements. Thermogravimetric analysis shows that the improved flame retardancy is due to increased char residue at high temperature. The loading of APP disturbs the compatibility between PLA and fibers, which can be directly observed using scanning electron microscopy. Furthermore it has an influence on the dynamic mechanical properties and mechanical properties according dynamic mechanical analysis and mechanical measurements. The results show that composites produced using the third process not only have the best flame retardancy but also comparatively better mechanical properties. Copyright © 2009 Society of Chemical Industry     

Effects of two kinds of THEIC‐based charring agents on flame‐retardant properties of polylactide

Two charring agents tris (2‐hydrooxyethyl) isocyanurate terephthalic acid ester, (dimer/trimer mixture TT23, and tetramer TT4) were synthesized by using tris (2‐hydrooxyethyl) isocyanurate (THEIC) and terephthalic acid (TPA) as raw materials. These two charring agents were combined with ammonium polyphosphate (APP) to form intumescent flame retardants (IFR) for polylactide (PLA). The thermal stability of IFRs were tested by TGA, it is found that APP/TT4 mixture has a higher thermal stability and a better char forming ability than that of APP/TT23 mixture. The combustion properties and thermal stability of PLA/APP/TT23 and PLA/APP/TT4 composites were evaluated by UL‐94 burning tests, limiting oxygen index (LOI), cone calorimeter tests and TGA, the chemical structure of char residues were analyzed by FTIR and XPS. It can be concluded that PLA with 30 wt % of APP/TT4 (weight ratio 5 : 1) achieved the greatest flame retardancy. Moreover, the continuous and expansionary char layer observed from SEM images proved better char forming ability of TT4 than that of TT23. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42086.     

Thermal oxidative degradation kinetics of PP and PP/mg (OH)2 flame‐retardant composites

The thermal stability and thermal oxidative degradation kinetics of polypropylene (PP) and flame‐retardant PP composites filled with untreated and treated magnesium hydroxide (MH) in air were studied by thermogravimetric analysis (TGA). The effect of the heating rate in dynamic measurements (5°C–30°C/min) on kinetic parameters such as activation energy was also investigated. The Kissinger and Flynn–Wall–Ozawa methods were used to determine the apparent activation energy for the degradation of neat PP and flame‐retardant PP composites. The results of TGA showed that the addition of untreated or treated MH improved the thermal oxidative stability of PP in air. The kinetic results showed that the apparent activation energy for degradation of flame‐retardant PP composites was much higher than that of neat PP, suggesting that the flame retardant used in this work had a great effect on the mechanisms of pyrolysis and combustion of PP. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1978–1984, 2007     

Simultaneously enhanced fracture toughness and flame‐retardant property of poly(l‐lactic acid) via reactive blending with ammonium polyphosphate and in situ formed polyurethane

The preparation of poly(l ‐lactic acid) (PLLA) with high mechanical and ideal flame‐retardant properties is a great challenge. Herein, a simultaneous toughness and flame‐retardant PLLA composite was successfully fabricated by using a one‐step process which introduces 4,4′‐methylenediphenyl diisocyanate and ammonium polyphosphate (APP) into PLLA/poly(ε‐caprolactone) blends. SEM, Fourier transform infrared spectroscopy and TGA were adopted to confirm that APP participated in the in situ reaction during the melt process. The impact strength was increased to 13.5 kJ m^?2 from 1.0 kJ m^?2 for L8P2A5 composite, indicating the toughening effect of reactive blending. The cone calorimeter test, limiting oxygen index and vertical burning test results indicate that the flame‐retardant properties of the composites are enhanced with increasing APP content. This work provides a method to prepare PLLA with high mechanical properties and enhanced flame retardancy. © 2020 Society of Chemical Industry     

Synthesis of a novel cross‐linked organophosphorus‐nitrogen containing polymer and its application in flame retardant epoxy resins

A novel cross‐linked organophosphorus–nitrogen polymetric flame retardant additive poly(urea tetramethylene phosphonium sulfate) defined as PUTMPS was synthesized by the condensation polymerization between urea and tetrahydroxymethyl phosphonium sulfate. Its chemical structure was well characterized by Fourier transform infrared (FTIR) spectroscopy, ¹³C and ³¹P solid‐state nuclear magnetic resonance. The synthesized PUTMPS and curing agent m‐phenylenediamine were blended into epoxy resins to prepare flame retardant epoxy resin thermosets. The effects of PUTMPS on fire retardancy and thermal degradation behavior of EP/PUTMPS thermosets were investigated by limiting oxygen index (LOI), vertical burning test (UL‐94), cone calorimeter measurement, and thermalgravimetric analysis (TGA) tests. The surface morphologies and chemical compositions of char residues for cured epoxy resins were investigated by scanning electron microscopy and X‐ray photoelectron spectroscopy (XPS), respectively. Water resistant properties of epoxy resin thermosets were evaluated by putting the samples into distilled water at 70°C for 168 h. The results demonstrated that the EP/12 wt% PUTMPS thermosets successfully passed UL‐94 V‐0 flammability rating and the LOI value reached 31.3%. The TGA results indicated that the incorporation of PUTMPS promoted epoxy resin matrix decomposed and char forming ahead of time, which led to a higher char yield and thermal stability for epoxy resin thermosets at high temperature. The morphological structures and analysis of XPS for the char residues of the epoxy resin thermosets shown that PUTMPS benefited to the formation of a sufficient, more compact, and homogeneous char layer with rich flame retardant elements on the materials surface during burning, which prevented the heat transmission and diffusion, limited the production of combustible gases, inhibited the emission of smoke, and then led to the reduction of the heat release rate and smoke produce rate. After water resistance tests, EP/12 wt% PUTMPS thermosets still remained excellent flame retardancy. Copyright © 2015 John Wiley & Sons, Ltd.