Corrosion behavior of plasma-sprayed coatings on a Ni-base superalloy in Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-60 Pct V<Subscript>2</Subscript>O<Subscript>5</Subscript> environment at 900 °C

The shrouded plasma spray process was used to deposit NiCrAlY, Ni-20Cr, Ni₃Al, and Stellite-6 metallic coatings on a Ni-based superalloy (62Ni-23Cr-1.48Al-0.80Mn-0.37Si-0.10Cu-0.025C-bal Fe). NiCrAlY was used as a bond coat in all cases. Hot corrosion studies were conducted on uncoated as well as plasma-spray-coated superalloy specimens after exposure to molten salt at 900 °C under cyclic conditions. The thermogravimetric technique was used to establish the kinetics of corrosion. X-ray diffraction (XRD), scanning electron microscopy/energy-dispersive X-ray analysis (SEM/EDAX) and electron-probe microanalysis techniques were used to analyze the corrosion products. The uncoated superalloy suffered accelerated corrosion in the form of intense spalling of the scale. The NiCrAlY coated specimen showed a minimum weight gain, whereas the Stellite-6 indicated a maximum weight gain among the coatings studied. All the coatings were found to be successful in developing resistance against hot corrosion, which may be attributed to the formation of oxides, and spinels of nickel, aluminum, chromium, or cobalt.     

Observation of the crystallization behavior of a slag containing 46 wt pct CaO, 46 wt pct SiO<Subscript>2</Subscript>, 6 wt pct Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, and 2 wt pct Na<Subscript>2</Subscript>O using the double hot thermocouple technique

In this work, isothermal crystallization of a synthetic slag containing 46 wt pct CaO, 46 wt pct SiO₂, 6 wt pct Al₂O₃, and 2 wt pct Na₂O has been investigated by means of double hot thermocouple technique (DHTT). The effect of Na₂O content on crystallization time was confirmed. Two different types of calcium silicate crystals were observed. Calcium di-silicate forms at temperatures above 1150 °C and calcium tri-silicate precipitate at temperatures below 1050 °C. A mixture of the two types of calcium silicate has been observed between the two temperatures. The tendency of crystals to become richer in calcium at low temperatures that has also been observed in previous published works has been confirmed. No effect of the cooling rate on crystallization start time was confirmed in the range of cooling rates applied in this investigation.     

Preparation of V<Subscript>2</Subscript>O<Subscript>5</Subscript> from Ammonium Metavanadate via Microwave Intensification

Parameters of technique to prepare of V₂O₅ by microwave intensification from ammonium metavanadate were optimized using central composite design of response surface methodology. A quadratic equation model for decomposition rate was built and effects of main factors and their corresponding relationships were obtained. The microwave heating behavior indicated that ammonium metavanadate had weak capability to absorb microwave radiation, while V₂O₅ had good capability to absorb microwave radiation. The results of the statistical analysis showed that the decomposition rate of ammonium metavanadate was significantly affected by calcination temperature and calcination time in the range studied. The optimized conditions were as follows: calcination temperature 645.35 K, calcination time 9.66 min and 4.3 g, respectively. The decomposition rates of ammonium metavanadate were 99.13%, which coincided well with experiments values 99.33% under these conditions. These suggest that regressive equation fits the decomposition rates perfectly. XRD reveals that it is feasible to prepare the V₂O₅ by microwave intensification from ammonium metavanadate, which mixed with small amounts of V₂O₅.     

Electrochemical Behavior of an Amorphous and Nanocrystalline Fe<Subscript>79</Subscript>P<Subscript>13</Subscript>Si<Subscript>5</Subscript>V<Subscript>3</Subscript> Alloy in a Damp SO<Subscript>2</Subscript>-Contaminated Atmosphere

The electrochemical behavior of amorphous and nanocrystalline soft magnetic Fe₇₉P₁₃Si₅V₃ alloy in a 0.1 M Na₂SO₄ solution has been studied. Mössbauer studies show that the electrochemical characteristics of the alloy are comparable with those of an Finemet Fe₇₇Si₁₃B₇Nb_2.1Cu_0.9 alloy, whereas the studied alloy is inexpensive and can be prepared using natural alloy ferrophosphorus containing vanadium and silicon.     

Distribution Ratios of Phosphorus Between CaO-FeO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Na<Subscript>2</Subscript>O/TiO<Subscript>2</Subscript> Slags and Carbon-Saturated Iron

In order to effectively enhance the efficiency of dephosphorization, the distribution ratios of phosphorus between CaO-FeO-SiO₂-Al₂O₃/Na₂O/TiO₂ slags and carbon-saturated iron (\( L_{\text{P}}^{\text{Fe-C}} \)) were examined through laboratory experiments in this study, along with the effects of different influencing factors such as the temperature and concentrations of the various slag components. Thermodynamic simulations showed that, with the addition of Na₂O and Al₂O₃, the liquid areas of the CaO-FeO-SiO₂ slag are enlarged significantly, with Al₂O₃ and Na₂O acting as fluxes when added to the slag in the appropriate concentrations. The experimental data suggested that \( L_{\text{P}}^{\text{Fe-C}} \) increases with an increase in the binary basicity of the slag, with the basicity having a greater effect than the temperature and FeO content; \( L_{\text{P}}^{\text{Fe-C}} \) increases with an increase in the Na₂O content and decrease in the Al₂O₃ content. In contrast to the case for the dephosphorization of molten steel, for the hot-metal dephosphorization process investigated in this study, the FeO content of the slag had a smaller effect on \( L_{\text{P}}^{\text{Fe-C}} \) than did the other factors such as the temperature and slag basicity. Based on the experimental data, by using regression analysis, \( \log L_{\text{P}}^{\text{Fe-C}} \) could be expressed as a function of the temperature and the slag component concentrations as follows:

$$ \begin{aligned} \log L_{\text{P}}^{\text{Fe-C}} & = 0.059({\text{pct}}\;{\text{CaO}}) + 1.583\log ({\text{TFe}}) - 0.052\left( {{\text{pct}}\;{\text{SiO}}_{2} } \right) - 0.014\left( {{\text{pct}}\;{\text{Al}}_{2} {\text{O}}_{3} } \right) \\ \, & \quad + 0.142\left( {{\text{pct}}\;{\text{Na}}_{2} {\text{O}}} \right) - 0.003\left( {{\text{pct}}\;{\text{TiO}}_{2} } \right) + 0.049\left( {{\text{pct}}\;{\text{P}}_{2} {\text{O}}_{5} } \right) + \frac{13{,}527}{T} - 9.87. \\ \end{aligned} $$

     

Influence of CaF<Subscript>2</Subscript> and Li<Subscript>2</Subscript>O on the Viscous Behavior of Calcium Silicate Melts Containing 12 wt pct Na<Subscript>2</Subscript>O

Understanding the viscous behavior of silica-based molten fluxes is essential in maintaining the reliability of steel casting operations and in preventing breakouts. In particular, high concentrations of aluminum in recently developed transformation induced plasticity (TRIP) and twinning induced plasticity (TWIP) steels tend to promote reduction of silica in the mold fluxes that result in the formation of alumina, which in turn increases the viscosity. To counteract this effect, significant amounts of fluidizers such as CaF₂ and Li₂O are required to ensure that mold fluxes have acceptable lubrication and heat transfer characteristics. The viscous behavior of the slag system based on CaO-SiO₂-12 wt pct Na₂O with various concentrations of CaF₂ and Li₂O has been studied using the rotating spindle method to understand the effects on the viscosity with these additives. CaF₂ additions up to 8 wt pct were effective in decreasing the viscosity by breaking the network structure of molten fluxes, but CaF₂ concentrations above this level had a negligible effect on viscosity. Li₂O additions up to 2 wt pct were also effective in decreasing the viscosity, but the effect was comparatively negligible above 2 wt pct. Using Fourier transform infrared (FTIR) analysis of as-quenched slag samples, it was concluded that the viscosity was controlled more effectively by changing the larger complex silicate structures of rings and chains than by changing the amounts of simpler dimers and monomers.     

Understanding the Relationship Between Structure and Thermophysical Properties of CaO-SiO<Subscript>2</Subscript>-MgO-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Molten Slags

In the present work, the relationship between the microscopic structure and macroscopic thermophysical properties in a basic CaO-SiO₂-MgO-Al₂O₃ quaternary system was identified using Fourier transformation infrared, Raman and ²⁷Al magic angular spinning nuclear magnetic resonance (MAS-NMR) techniques. The Raman spectra quantitatively proved that with increasing Al₂O₃ content, the concentrations of the symmetric units of Q⁰(Si) and Q²(Si) decreased, while those of the asymmetric units of Q¹(Si) and Q³(Si) increased; consequently, the degree of polymerization of the networks increased, which resulted in an increase in slag viscosity. The ²⁷Al MAS-NMR spectra demonstrated that three structural units of Al atoms, namely, AlO₄, AlO₅, and AlO₆, mainly existed in the networks. With increasing Al₂O₃ content, the concentration of AlO₄ slightly decreased, while those of AlO₅ and AlO₆ increased; overall, Al₂O₃ acted as a network former in the present system. The increasing Al₂O₃ content led to additional AlO₆ and Si-NBO-Ca-NBO-Al frameworks, which replaced Si-NBO-Ca-NBO-Si in the networks (NBO: non-bridging oxygen) and induced a change in the primarily precipitated crystalline phase from Ca₂MgSi₂O₇ and Ca₂Al₂SiO₇ to MgAlO₄.     

Crystallization Behavior and Microstructure of Silica-Free 5K<Subscript>2</Subscript>O-45CaO-50P<Subscript>2</Subscript>O<Subscript>5</Subscript> Bioglass

The crystallization behavior and microstructure of silica-free 5K₂O-45CaO-50P₂O₅ (KCP) bioglass have been studied using differential thermal analysis (DTA), X-ray diffraction (XRD), scanning election microscopy (SEM), transmission electron microscopy (TEM), and selected area electron diffraction (SAED). The activation energy for the KCP bioglass crystallization is found to be 337.4 kJ/mol using a nonisothermal method. The crystalline phases of the glass surface determined by XRD are KCa(PO₃)₃, 4CaO·3P₂O₅, and β-Ca(PO₃)₂ when the KCP bioglass is crystallized at 903 K for 4 hours. The crystalline phase of the powder samples determined by XRD is β-Ca(PO₃)₂ when silica-free KCP glasses crystallized at 873 to 1073 K for 8 hours. Crystallization starts at the surface of the KCP bioglass and then proceeds toward the interior of the glass matrix. The morphology of β-Ca(PO₃)₂ is a fibrillar shape 20 to 180 nm in length and 17 to 20 nm in diameter, with an aspect ratio ranging from 1.0 to 10.6.     

Effect of Na<Subscript>2</Subscript>CO<Subscript>3</Subscript> Addition on Inclusions in High-Carbon Steel for Saw Wire

Inclusions cannot be sufficiently stretched to adapt extremely strict requirement of saw wire with only conventional inclusion softening art. In order to explore a potential new method to further enhance the deformability of inclusions, Na₂CO₃ addition should be comprehensively investigated due to the extremely low melting temperature of inclusions containing Na₂O. In the present study, an effective method of Na₂CO₃ addition was put forward and a presumable reaction mechanism between Na₂CO₃/steel/inclusion/slag was deduced by studying the effect of Fe/Na₂CO₃ (weight ratio), Na₂CO₃ addition amount and reaction time on inclusions using a graphite tube resistance furnace. The relations between Na₂O content, melting temperature, deformability and crystallization of inclusions were also briefly discussed. Through these studies, the deformability of inclusions was significantly improved on the whole.     

Electrochemical Behavior of Silicon in the (NaCl-KCl-NaF-SiO<Subscript>2</Subscript>) Molten Salt

The electrochemical behavior of silicon was investigated in a molten salts system including saturation silicon dioxide. Silicon was electrodeposited and MoSi₂ was formed on the employed molybdenum working electrode by the diffusivities of silicon and the substrate metals. Transient electrochemical techniques such as cyclic voltammetry and chronoamperometry were used to study the reaction mechanism at the molybdenum electrode. Cyclic voltammograms showed the possibility of electrodeposition of Si at −0.64 V versus Pt reference electrode in a NaCl-KCl-NaF-SiO₂ system at 1073 K (800 °C). The electrodeposition of Si is single-step charge-transfer process and the cathode process is irreversible. Chronoamperometry studies indicated that electrocrystallization of Si is controlled by progressive nucleation with a three-dimensional growth mechanism.     

Separation of Fine Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Inclusion from Liquid Steel with Super Gravity

An innovative approach of super gravity was proposed to separate fine Al₂O₃ inclusions from liquid steel in this study. To investigate the removal behaviors of inclusions, the effects of different gravity coefficients and time on separating the inclusions were studied. The results show that a large amount of Al₂O₃ inclusions gathered at the top of the sample obtained by super gravity, whereas there were almost no inclusions appearing at the bottom. The volume fraction and number density of inclusions presented a gradient distribution along the direction of the super gravity, which became steeper with increasing gravity coefficient and separating time. As a result of the collision between inclusions, a large amount of inclusions aggregated and grew during the moving process, which further decreased the removal time. The experimental required removal time of inclusions is close to the theoretical values calculated by Stokes law under gravity coefficient G ≤ 80, t ≤ 15 minutes, and the small deviation may be because the inclusion particles are not truly spherical. Under the condition of gravity coefficient G = 80, t = 15 minutes, the total oxygen content at the bottom of the sample (position of 5 cm) is only 8.4 ppm, and the removal rate is up to 95.6 pct compared with that under normal gravity.     

Effect of LiF as Sintering Agent on the Densification and Phase Formation in Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-4 Wt Pct Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> Ceramic Compound

Different amounts of LiF were added to an Al₂O₃-4 pct Nb₂O₅ basic ceramic, as sintering agent. Improved new ceramics were obtained with LiF concentrations varying from 0.25 to 1.50 wt pct and three sintering temperatures of 1573 K, 1623 K, and 1673 K (1300 °C, 1350 °C, and 1400 °C). The addition of 0.5 wt pct LiF yielded the highest densification, 94 pct of the theoretical density, in association with a sintering temperature of 1673 K (1400 °C). Based on X-ray diffraction (XRD), this improvement was due not only to the presence of transformed phases, more precisely Nb₃O₇F, but also to the absence of LiAl₅O₈. The preferential interaction of LiF with Nb₂O₅, instead of Al₂O₃, contributed to increase the alumina sintering ability by liquid phase formation. Scanning electron microscopy (SEM) results revealed well-connected grains and isolated pores, whereas the chemical composition analysis by energy dispersive energy (EDX) indicated a preferential interaction of fluorine with niobium, in agreement with the results of XRD. It was also observed from thermal analysis that the polyethylene glycol binder burnout temperature increased for all LiF concentrations. This may be related to the formation of hydrogen bridge bonds.     

Interaction of W<Subscript>2</Subscript>B<Subscript>5</Subscript> with Me<Superscript>IV,V</Superscript>C carbides

It is established that the W₂B₅-Me^IV,VC join in the W-B-C-Me^IV,V quaternary systems is quasibinary, while polythermal joins are described by eutectic phase diagrams. It is shown that the eutectic composition and temperature correlate with the melting points of carbides and the Me ^d C content varies from 50 mol % in the W₂B₅-VC system to 4–6 mol % in the W2B5-TaC system. The existence of Me ^d C-Me ^d B₂-W₂B₅ ternary eutectic systems promising for the development of new ceramics is proved.     

Decomposition of Y<Subscript>2</Subscript>Ti<Subscript>2</Subscript>O<Subscript>7</Subscript> Particles in 8 Pct Cr Oxide-Dispersion-Strengthened Martensitic Steel during Tempering

Chemical composition analysis using inductively coupled plasma spectroscopy and phase identification using X-ray were performed on the extracted residues of 8 pct Cr martensitic steel strengthened by nanoscaled complex oxides, which consist of yttrium, titanium, and oxygen. Some Y₂Ti₂O₇ particles, which were stable during normalizing, decomposed into Y₂O₃ and Ti₂O₃ during tempering. This reaction reversibly occurred between normalizing and tempering. Y₂Ti₂O₇ particles formed in the steel had other constituents in solid solution as compared to the completely stoichiometric Y₂Ti₂O₇ particles synthesized artificially in air. As for the mechanism of the decomposition of Y₂Ti₂O₇ particles in the steel, segregation of oxygen to dislocations induced by normalizing caused the decomposition of Y₂Ti₂O₇ during tempering. In addition to that, the interfacial strain between Y₂O₃ particles or Ti₂O₃ particles within Cr₂₃C₆ carbides, which are formed by tempering, was lower than the strain between Y₂Ti₂O₇, which precipitated in Cr₂₃C₆ carbides or the matrix. This difference in interfacial strain could also promote the decomposition of the Y₂Ti₂O₇ particles in the steel.     

Effect of Superficially Applied Y<Subscript>2</Subscript>O<Subscript>3</Subscript> Coating on High-Temperature Corrosion Behavior of Ni-Base Superalloys

Inhibitors and oxide additives have been investigated with varying success to control high-temperature corrosion. Effect of Y₂O₃ on high-temperature corrosion of Superni 718 and Superni 601 superalloys was investigated in the Na₂SO₄-60 pct V₂O₅ environment at 1173 K (900 °C) for 50 cycles. Y₂O₃ was applied as a coating on the surfaces of the specimens. Superni 601 was found to have better corrosion resistance in comparison with Superni 718 in the Na₂SO₄-60 pct V₂O₅ environment. The Y₂O₃ superficial coating was successful in decreasing the reaction rate for both the superalloys. In the oxide scale of the alloy Superni 601, Y and V were observed to coexist, thereby indicating the formation of a protective YVO₄ phase. There was a distinct presence of a protective Cr₂O₃-rich layer just above the substrate/scale interface in the alloy. Whereas Cr₂O₃ was present with Fe and Ni in the scale of Superni 718. Y₂O₃ seemed to be contributing to better adhesion of the scale, as comparatively lesser spalling was noticed in the presence of Y₂O₃.     

Development of Wear-Resistant Cu-10Cr-3Ag Electrical Contacts with Nano-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Dispersion by Mechanical Alloying and High Pressure Sintering

Cu-10Cr-3Ag (wt pct) alloy with nanocrystalline Al₂O₃ dispersion was prepared by mechanical alloying and consolidated by high pressure sintering at different temperatures. Characterization by X-ray diffraction and scanning electron microscopy or transmission electron microscopy shows the formation of nanocrystalline matrix grains of about 40 nm after 25 hours of milling with nanometric (<20 nm) Al₂O₃ particles dispersed in it. After consolidation by high pressure sintering (8 GPa at 400 °C to 800 °C), the dispersoids retain their ultrafine size and uniform distribution, while the alloyed matrix undergoes significant grain growth. The hardness and wear resistance of the pellets increase significantly with the addition of nano-Al₂O₃ particles. The electrical conductivity of the pellets without and with nano-Al₂O₃ dispersion is about 30 pct IACS (international annealing copper standard) and 25 pct IACS, respectively. Thus, mechanical alloying followed by high pressure sintering seems a potential route for developing nano-Al₂O₃ dispersed Cu-Cr-Ag alloy for heavy duty electrical contact.