An Analytical Method to Extract the Physical Parameters of a Solar Cell From Four Points on the Illuminated $J{-}V$ Curve

For a variety of solar cells, it is shown that the single exponential $J{-}V$ model parameters, namely—ideality factor $eta$ , parasitic series resistance $R_{s}$, parasitic shunt resistance $R_{rm sh}$, dark current $J_{0}$, and photogenerated current $J_{rm ph}$ can be extracted simultaneously from just four simple measurements of the bias points corresponding to $V_{rm oc}$, $sim!hbox{0.6}V_{rm oc}$, $J_{rm sc}$, and $sim! hbox{0.6}J_{rm sc}$ on the illuminated $J{-}V$ curve, using closed-form expressions. The extraction method avoids the measurements of the peak power point and any $dJ/dV$ (i.e., slope). The method is based on the power law $J{-}V$ model proposed recently by us.      

Extraction of the Effective Mobility of $ hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs

The extraction of the effective mobility on $hbox{In}_{0.53} hbox{Ga}_{0.47}hbox{As}$ metal–oxide–semiconductor field-effect transistors (MOSFETs) is studied and shown to be greater than 3600 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$. The removal of $C_{rm it}$ response in the split $C$–$V$ measurement of these devices is crucial to the accurate analysis of these devices. Low-temperature split $C$–$V$ can be used to freeze out the $D_{rm it}$ response to the ac signal but maintain its effect on the free carrier density through the substrate potential. Simulations that match this low-temperature data can then be “warmed up” to room temperature and an accurate measure of $Q_{rm inv}$ is achieved. These results confirm the fundamental performance advantages of $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs.      

1580-V–40-$hbox{m}Omegacdot hbox{cm}^{2}$ Double-RESURF MOSFETs on 4H-SiC $(hbox{000}bar{hbox{1}})$

Double-reduced-surface-field (RESURF) MOSFETs with $hbox{N}_{2}hbox{O}$ -grown oxides have been fabricated on the 4H-SiC $(hbox{000} bar{hbox{1}})$ face. The double-RESURF structure is effective in reducing the drift resistance, as well as in increasing the breakdown voltage. In addition, by utilizing the 4H-SiC $(hbox{000}bar{hbox{1}})$ face, the channel mobility can be increased to over 30 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, and hence, the channel resistance is decreased. As a result, the fabricated MOSFETs on 4H-SiC $( hbox{000}bar{hbox{1}})$ have demonstrated a high breakdown voltage $(V_{B})$ of 1580 V and a low on-resistance $(R_{rm ON})$ of 40 $hbox{m}Omega cdothbox{cm}^{2}$. The figure-of-merit $(V_{B}^{2}/R_{rm ON})$ of the fabricated device has reached 62 $hbox{MW/cm}^{2}$, which is the highest value among any lateral MOSFETs and is more than ten times higher than the “Si limit.”      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

Cubic-Structured $hbox{HfO}_{2}$ With Optimized Doping of Lanthanum for Higher Dielectric Constant

It is demonstrated that $hbox{HfO}_{2}$ films can have much higher dielectric-constant values than the usual reported value of 20–24 by optimized incorporation of lanthanum element and crystallization to cubic structure. When $hbox{HfO}_{2}$ with 8% La is crystallized into cubic structure, the film exhibits the $kappa$ value of $sim$ 38 which is the highest among ever reported $hbox{HfO}_{2}$ -based high-$kappa$ dielectrics. The increased $kappa$ value of $ hbox{HfO}_{2}$ with 8% La enables the leakage current to be reduced more than one order of magnitude lower, compared to amorphous-phase $hbox{HfO}_{2}$ under the same electric field. The dependence of film thickness and annealing temperature on the cubic crystallization is also reported.      

High-Density and Low-Leakage-Current MIM Capacitor Using Stacked $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Insulators

We have fabricated high-$kappa hbox{Ni}/hbox{TiO}_{2}/hbox{ZrO}_{2}/ hbox{TiN}$ metal–insulator–metal (MIM) capacitors. A low leakage current of $hbox{8} times hbox{10}^{-8} hbox{A/cm}^{2}$ at 125 $^{circ}hbox{C}$ was obtained with a high 38- $hbox{fF}/muhbox{m}^{2}$ capacitance density and better than the $hbox{ZrO}_{2}$ MIM capacitors. The excellent device performance is due to the lower electric field in 9.5-nm-thick $hbox{TiO}_{2}/ hbox{ZrO}_{2}$ devices to decrease the leakage current and to a higher $kappa$ value of 58 for $ hbox{TiO}_{2}$ as compared with that of $hbox{ZrO}_{2}$ to preserve the high capacitance density.      

A 67 dBm $OIP_{3}$ Multistacked Junction Varactor

A multistacked varactor is presented for ultra-linear tunable radio frequency applications. The varactor elements are applied in anti-series configuration and are characterized by an “exponential” $C$- $V _{R}$ relationship. Third-order intermodulation ($IM_{3}$) is cancelled through proper harmonic loading of the terminals of the anti-series configuration. Multiple stacking is used to further increase the power handling and to minimize the remaining fifth-order distortion. The measured output intercept point ($OIP_{3}$ ) at 2 GHz is $ > 67~{rm dBm}$ for modulated signals up to 10 MHz bandwidth, while providing a capacitance tuning ratio of 3:1 with an average quality factor of 40 and maximum control voltage of 10 V.      

A 125–1250 MHz Process-Independent Adaptive Bandwidth Spread Spectrum Clock Generator With Digital Controlled Self-Calibration

A process-independent adaptive bandwidth spread-spectrum clock generator (SSCG) with digitally controlled self-calibration techniques is proposed. By adaptively calibrating the VCO gain ($K_v$) and charge-pump (CP) current over C ($I_{CP}/C$), the SSCG can realize not only adaptive bandwidth but also process independence at each operating frequency. The innovative point is the adaptive bandwidth control using $K_v$ and $I_{CP}/C$ calibration. This control enabled a test chip to keep a sharp triangular SSC profile while operating over a wide frequency range (125 to 1250 $~$MHz). The variations of VCO gain and CP current are reduced to one third those of the conventional architecture. At 1250 $~$Mbps (625$~$MHz) the reduction of spectrum peak amplitude is 18.6$~$dB which is 2.3$~$dB better than the reduction obtained without calibration.      

Virus Spread in Networks

The influence of the network characteristics on the virus spread is analyzed in a new—the $N$ -intertwined Markov chain—model, whose only approximation lies in the application of mean field theory. The mean field approximation is quantified in detail. The $N$ -intertwined model has been compared with the exact $2^{N}$-state Markov model and with previously proposed “homogeneous” or “local” models. The sharp epidemic threshold $tau_{c}$ , which is a consequence of mean field theory, is rigorously shown to be equal to $tau_{c}=1/(lambda_{max}(A))$ , where $lambda_{max}(A)$ is the largest eigenvalue—the spectral radius—of the adjacency matrix $A$ . A continued fraction expansion of the steady-state infection probability at node $j$ is presented as well as several upper bounds.      

Positive Bias Temperature Instability (PBTI) Characteristics of Contact-Etch-Stop-Layer-Induced Local-Tensile-Strained $hbox{HfO}_{2}$ nMOSFET

The positive bias temperature instability (PBTI) characteristics of contact-etch-stop-layer (CESL)-strained $hbox{HfO}_{2}$ nMOSFET are thoroughly investigated. For the first time, the effects of CESL on an $hbox{HfO}_{2}$ dielectric are investigated for PBTI characteristics. A roughly 50% reduction of $V_{rm TH}$ shift can be achieved for the 300-nm CESL $hbox{HfO}_{2}$ nMOSFET after 1000-s PBTI stressing without obvious $ hbox{HfO}_{2}/hbox{Si}$ interface degradation, as demonstrated by the negligible charge pumping current increase ($≪$ 4%). In addition, the $hbox{HfO}_{2}$ film of CESL devices has a deeper trapping level (0.83 eV), indicating that most of the shallow traps (0.75 eV) in as-deposited $ hbox{HfO}_{2}$ film can be eliminated for CESL devices.      

Performance Improvement of N-Type $hbox{TiO}_{x}$ Active-Channel TFTs Grown by Low-Temperature Plasma-Enhanced ALD

We report on performance improvement of $n$-type oxide–semiconductor thin-film transistors (TFTs) based on $hbox{TiO}_{x}$ active channels grown at 250 $^{circ}hbox{C}$ by plasma-enhanced atomic layer deposition. TFTs with as-grown $hbox{TiO}_{x}$ films exhibited the saturation mobility $(mu_{rm sat})$ as high as 3.2 $hbox{cm}^{2}/hbox{V}cdothbox{s}$ but suffered from the low on–off ratio $(I_{rm ON}/I_{rm OFF})$ of $hbox{2.0} times hbox{10}^{2}$. $hbox{N}_{2}hbox{O}$ plasma treatment was then attempted to improve $I_{rm ON}/I_{rm OFF}$. Upon treatment, the $hbox{TiO}_{x}$ TFTs exhibited $I_{rm ON}/I_{rm OFF}$ of $hbox{4.7} times hbox{10}^{5}$ and $mu_{rm sat}$ of 1.64 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, showing a much improved performance balance and, thus, demonstrating their potentials for a wide variety of applications such as backplane technology in active-matrix displays and radio-frequency identification tags.      

Ultrafast Measurement on NBTI

We combine customary pulsed $I$– $V$ setup with a simple linear drain–current correction method to provide a possible standard for NBTI characterization. The method is implemented using standard equipment and yet is able to achieve sub-100-ns delay, the shortest reported to date for a wafer-level setup. Unlike the ramped-voltage method for which synchronization of the gate and drain waveforms is critical, relative delay between the gate and drain signals is not a concern in our case since measurement is made during quasi-steady state. For the present setup, gate and drain signals are shown to “stabilize” after $sim!hbox{50}$ ns (upon switching) for a gate capacitive load of 1.5 pF (equivalent to $sim!hbox{80} $ devices used in this letter), rendering parallel testing possible using a single gate voltage source. Extension of the method for direct threshold voltage extraction by the constant subthreshold drain current approach is also discussed.      

Impacts of $hbox{N}_{2}$ and $hbox{NH}_{3}$ Plasma Surface Treatments on High-Performance LTPS-TFT With High-$kappa$ Gate Dielectric

Low-temperature polycrystalline-silicon thin-film transistors (LTPS-TFTs) with high- $kappa$ gate dielectrics and plasma surface treatments are demonstrated for the first time. Significant field-effect mobility $mu_{rm FE}$ improvements of $sim$86.0% and 112.5% are observed for LTPS-TFTs with $hbox{HfO}_{2}$ gate dielectric after $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments, respectively. In addition, the $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments can also reduce surface roughness scattering to enhance the field-effect mobility $mu_{rm FE}$ at high gate bias voltage $V_{G}$, resulting in 217.0% and 219.6% improvements in driving current, respectively. As a result, high-performance LTPS-TFT with low threshold voltage $V_{rm TH} sim hbox{0.33} hbox{V}$, excellent subthreshold swing S.S. $sim$0.156 V/decade, and high field-effect mobility $mu_{rm FE} sim hbox{62.02} hbox{cm}^{2}/hbox{V} cdot hbox{s}$ would be suitable for the application of system-on-panel.      

Characterization and Modeling of RF-Performance $(f_{T})$ Fluctuation in MOSFETs

The fluctuation of RF performance (particularly for $f_{T}$ : cutoff frequency) in the transistors fabricated by 90-nm CMOS technology has been investigated. The modeling for $f_{T}$ fluctuation is well fitted with the measurement data within approximately 1% error. Low-$V_{t}$ transistors (fabricated by lower doping concentration in the channel) show higher $f_{T}$ fluctuation than normal transistors. Such a higher $f_{T}$ fluctuation results from $C_{rm gg}$ (total gate capacitance) variation rather than $g_{m}$ variation. More detailed analysis shows that $C_{rm gs} + C_{rm gb}$ (charges in the channel and the bulk) are predominant factors over $C_{rm gd}$ (charges in LDD/halo region) to determine $C_{rm gg}$ fluctuation.      

Pulsed $I_{d}$– $V_{g}$ Methodology and Its Application to Electron-Trapping Characterization and Defect Density Profiling

The pulsed current–voltage ($I$– $V$) measurement technique with pulse times ranging from $sim$17 ns to $sim$ 6 ms was employed to study the effect of fast transient charging on the threshold voltage shift $Delta V_{t}$ of MOSFETs. The extracted $Delta V_{t}$ values are found to be strongly dependent on the band bending of the dielectric stack defined by the high-$kappa$ and interfacial layer dielectric constants and thicknesses, as well as applied voltages. Various hafnium-based gate stacks were found to exhibit a similar trap density profile.      

Anisotropic Transient and Stationary Electron Velocity in Bulk Wurtzite GaN

The theoretical calculation of transient electron velocity overshoot in wurtzite $c$-axis GaN indicates a higher transient overshoot peak for transport in the basal plane ( $Gammahbox{-}M$ and $Gamma hbox{-}K$) than along the growth direction ($Gammahbox{-}A$ ). Characteristic rise times for the transient overshoot peak are found to be shorter for transport along the $c$-axis. Stationary electron velocity is significantly larger for transport oriented in the basal plane than along the $c$ -axis. No significant anisotropy is observed, however, in either the transient or steady-state electron velocity as a function of field orientation within the basal plane itself. The higher peak transient and stationary velocities in the basal plane are directly attributable to the anisotropy of the electronic dispersion, which exhibits lower effective mass along the $Gammahbox{-}M$ and $Gammahbox{-}K$ directions and greater nonparabolicity along the $Gammahbox{-}A$ direction.      

17 GHz RF Front-Ends for Low-Power Wireless Sensor Networks

A 17 GHz low-power radio transceiver front-end implemented in a 0.25 $mu{hbox {m}}$ SiGe:C BiCMOS technology is described. Operating at data rates up to 10 Mbit/s with a reduced transceiver turn-on time of 2 $mu{hbox {s}}$, gives an overall energy consumption of 1.75 nJ/bit for the receiver and 1.6 nJ/bit for the transmitter. The measured conversion gain of the receiver chain is 25–30 dB into a 50 $Omega$ load at 10 MHz IF, and noise figure is 12 $pm$0.5 dB across the band from 10 to 200 MHz. The 1-dB compression point at the receiver input is $-$37 dBm and ${hbox{IIP}}_{3}$ is $-$25 dBm. The maximum saturated output power from the on-chip transmit amplifier is $-$1.4 dBm. Power consumption is 17.5 mW in receiver mode, and 16 mW in transmit mode, both operating from a 2.5 V supply. In standby, the transceiver supply current is less than 1 $mu{hbox {A}}$.      

Linear Systems, Sparse Solutions, and Sudoku

In this paper, we show that Sudoku puzzles can be formulated and solved as a sparse linear system of equations. We begin by showing that the Sudoku ruleset can be expressed as an underdetermined linear system: ${mmb{Ax}}={mmb b}$, where ${mmb A}$ is of size $mtimes n$ and $n>m$. We then prove that the Sudoku solution is the sparsest solution of ${mmb{Ax}}={mmb b}$, which can be obtained by $l_{0}$ norm minimization, i.e. $minlimits_{mmb x}Vert{mmb x}Vert_{0}$ s.t. ${mmb{Ax}}={mmb b}$. Instead of this minimization problem, inspired by the sparse representation literature, we solve the much simpler linear programming problem of minimizing the $l_{1}$ norm of ${mmb x}$, i.e. $minlimits_{mmb x}Vert{mmb x}Vert_{1}$ s.t. ${mmb{Ax}}={mmb b}$, and show numerically that this approach solves representative Sudoku puzzles.      

CMOS Avalanche Photodiode Embedded in a Phase-Shift Laser Rangefinder

This paper presents the design and the characterization of a CMOS avalanche photodiode (APD) working as an optoelectronic mixer. The $hbox{P}^{+}hbox{N}$ photodiode has been implemented in a commercial 0.35-$muhbox{m}$ CMOS technology after optimization with SILVACO. The surface of the active region is $ hbox{3.78} cdot hbox{10}^{-3} hbox{cm}^{2}$. An efficient guard-ring structure has been created using the lateral diffusion of two n-well regions separated by a gap of 1.2 $mu hbox{m}$. When biased at $-$2 V, the best responsitivity $S_{lambda ,{rm APD}} = hbox{0.11} hbox{A/W}$ is obtained at $lambda = hbox{500} hbox{nm}$. This value can easily be improved by using an antireflection coating. At $lambda = hbox{472} hbox{nm}$, the internal gain is about 75 at $-$6 V and 157 at $-$7 V. When biased at $-$6 V, the APD achieves a dark current of 128 $muhbox{A} cdot hbox{mm}^{-2}$ and an excess noise factor $F = hbox{20}$ . Then, the APD is successfully used as an optoelectronic mixer to improve the signal-to-noise ratio of a low-voltage embedded phase-shift laser rangefinder.      

Integrated Hydrogen-Sensing Amplifier With GaAs Schottky-Type Diode and InGaP–GaAs Heterojunction Bipolar Transistor

New hydrogen-sensing amplifiers are fabricated by integrating a GaAs Schottky-type hydrogen sensor and an InGaP–GaAs heterojunction bipolar transistor. Sensing collector currents ( $I_{rm CN}$ and $I_{rm CH}$) reflecting to $hbox{N}_{2}$ and hydrogen-containing gases are employed as output signals in common-emitter characteristics. Gummel-plot sensing characteristics with testing gases as inputs show a high sensing-collector-current gain $(I_{rm CH}/I_{rm CN})$ of $≫hbox{3000}$. When operating in standby mode for in situ long-term detection, power consumption is smaller than 0.4 $muhbox{W}$. Furthermore, the room-temperature response time is 85 s for the integrated hydrogen-sensing amplifier fabricated with a bipolar-type structure.