An investigation of the thermal stability and sulphur tolerance of Ag/γ-Al2O3 catalysts for the SCR of NOx with hydrocarbons and hydrogen

The sulphur tolerance and thermal stability of a 2 wt% Ag/γ-Al₂O₃ catalyst was investigated for the H₂-promoted SCR of NO_x with octane and toluene. The aged catalyst was characterised by XRD and EXAFS analysis. It was found that the effect of ageing was a function of the gas mix and temperature of ageing. At high temperatures (800 °C) the catalyst deactivated regardless of the reaction mix. EXAFS analysis showed that this was associated with the Ag particles on the surface of the catalyst becoming more ordered. At 600 and 700 °C, the deactivating effect of ageing was much less pronounced for the catalyst in the H₂-promoted octane-SCR reaction and ageing at 600 °C resulted in an enhancement in activity for the reaction in the absence of H₂. For the toluene + H₂-SCR reaction the catalyst deactivated at each ageing temperature. The effect of addition of low levels of sulphur (1 ppm SO₂) to the feed was very much dependent on the reaction temperature. There was little deactivation of the catalyst at low temperatures (≤235 °C), severe deactivation at intermediate temperatures (305 and 400 °C) and activation of the catalyst at high temperatures (>500 °C). The results can be explained by the activity of the catalyst for the oxidation of SO₂ to SO₃ and the relative stability of silver and aluminium sulphates. The catalyst could be almost fully regenerated by a combination of heating and the presence of hydrogen in the regeneration mix. The catalyst could not be regenerated in the absence of hydrogen.     

Performance and deactivation of Ir/γ-Al2O3 catalyst in the hydrogen peroxide monopropellant thruster

The performance of Ir/γ-Al₂O₃ catalyst for the decomposition of high concentration hydrogen peroxide was investigated in a monopropellant thruster. The changes of ignition delay (t₀), chamber pressure (P_c) and catalyst bed temperature (T_c) with the numbers of startup–shutdown cycles were proved to be effective indicators of catalyst bed efficiency. The fresh catalyst and the deactivated catalyst were characterized with H₂-TPR, XRD and XPS. It was found that catalyst oxidation and surface Sn poisoning are the major reasons of catalyst deactivation.     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.     

CO, H2 or C3H8 assisted catalytic combustion of methane over supported LaMnO3 monoliths

The effect of the addition of a second fuel such as CO, C₃H₈ or H₂ on the catalytic combustion of methane was investigated over ceramic monoliths coated with LaMnO₃/La-γAl₂O₃ catalyst. Results of autothermal ignition of different binary fuel mixtures characterised by the same overall heating value show that the presence of a more reactive compound reduces the minimum pre-heating temperature necessary to burn methane. The effect is more pronounced for the addition of CO and very similar for C₃H₈ and H₂. Order of reactivity of the different fuels established in isothermal activity measurements was: CO>H₂≥C₃H₈>CH₄. Under autothermal conditions, nearly complete methane conversion is obtained with catalyst temperatures around 800 °C mainly through heterogeneous reactions, with about 60–70 ppm of unburned CH₄ when pure methane or CO/CH₄ mixtures are used. For H₂/CH₄ and C₃H₈/CH₄ mixtures, emissions of unburned methane are lower, probably due to the proceeding of CH₄ homogeneous oxidation promoted by H and OH radicals generated by propane and hydrogen pyrolysis at such relatively high temperatures.

Finally, a steady state multiplicity is found by decreasing the pre-heating temperature from the ignited state. This occurrence can be successfully employed to pilot the catalytic ignition of methane at temperatures close to compressor discharge or easily achieved in regenerative burners.     

Effect of hydrogen on reaction intermediates in the selective catalytic reduction of NOx by C3H6

Selective catalytic reduction of NO_x by C₃H₆ in the presence of H₂ over Ag/Al₂O₃ was investigated using in situ DRIFTS and GC–MS measurements. The addition of H₂ promoted the partial oxidation of C₃H₆ to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO_x on Ag/Al₂O₃ surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H₂ on the SCR of NO_x by C₃H₆ over Ag/Al₂O₃ catalyst.     

Hydrogen spill-over effect on Pt/WO3 anode catalysts

The experimental evidence and mechanism of ‘hydrogen spill-over’ on Pt/WO₃ is reviewed and the application of this catalyst system for the evolution of hydrogen, anodic oxidation, hydrogenation and the anodic oxidation of small molecules and impure H₂ is discussed. It is suggested that further work on preparation techniques to ensure the maximisation of Pt/WO₃ interfaces and other analogous systems should lead to even higher catalyst activity and applications.     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Hydrodeoxygenation of aliphatic esters on sulphided NiMo/γ-Al2O3 and CoMo/γ-Al2O3 catalyst: The effect of water

Water formed during hydrotreating of oxygen-containing feeds has been found to affect the performance of sulphided catalysts in different ways. The effect of water on the activity of sulphided NiMo/γ-Al₂O₃ and CoMo/γ-Al₂O₃ catalysts in hydrodeoxygenation (HDO) of aliphatic esters was investigated in a tubular reactor by varying the amount of water in the feed. In additional experiments, H₂S was added to the feed, alone and simultaneously with water.

Under the same conditions, the NiMo catalyst exhibited a higher activity than the CoMo catalyst. The ester conversions decreased with increase in the amount of added water. When H₂S and water were added simultaneously, the conversion increased to the same level as without water addition on the NiMo catalyst and reached a higher value on the CoMo catalyst. The conversions were highest, however, when only H₂S was added. Unfortunately, the conversions decreased with time under all conditions. On both catalysts, the total yield of the C₇ and C₆ hydrocarbons decreased with the amount of added water, while the concentrations of the oxygen-containing intermediates increased. The presence of H₂S improved the total hydrocarbon yield and shifted the main products towards the C₆ hydrocarbons. Thus, the addition of H₂S effectively compensated the inhibition by water.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

Influence of the co-feeding of CO, H2, CO2 or H2O in the partial oxidation of methane over Ni and Rh supported catalysts

The influence of the addition of 5 vol.% of carbon monoxide, hydrogen, carbon dioxide or water to the feed of partial oxidation of methane was investigated over Ni/γ-Al₂O₃ and Rh/γ-Al₂O₃ catalysts. In addition to catalytic tests, thermodynamic calculations were performed to predict the effect of these gas co-feeds. Compared to the thermodynamic trends, differences in the influence of the co-feeding on catalytic performances were observed between both catalysts. Co-feeding of CO, H₂, CO₂ or H₂O can modify the oxidation state and dispersion of the metal component of the catalysts during reaction, and as a consequence, their performances. Changes in catalysts can be due to dynamic processes occurring during reaction. It is suggested to take these processes into account in a more complex kinetic equation for the reactions involved.     

Effect of phosphorus addition on the hydrotreating activity of NiMo/Al2O3 carbide catalyst

A series of phosphorus promoted γ-Al₂O₃ supported NiMo carbide catalysts with 0–4.5 wt.% P, 13 wt.% Mo and 2.5 wt.% Ni were synthesized and characterized by elemental analysis, pulsed CO chemisorption, BET surface area measurement, X-ray diffraction, near-edge X-ray absorption fine structure, DRIFT spectroscopy of CO adsorption and H₂ temperature programmed reduction. X-ray diffraction patterns and CO uptake showed the P addition to NiMo/γ-Al₂O₃ carbide, increased the dispersion of β-Mo₂C particles. DRIFT spectra of adsorbed CO revealed that P addition to NiMo/γ-Al₂O₃ carbide catalyst not only increases the dispersion of Ni-Mo carbide phase, but also changes the nature of surface active sites. The hydrodenitrogenation (HDN) and hydrodesulfurization (HDS) activities of these P promoted NiMo/γ-Al₂O₃ carbide catalysts were performed in trickle bed reactor using light gas oil (LGO) derived from Athabasca bitumen and model feed containing quinoline and dibenzothiophene at industrial conditions. The P added NiMo/γ-Al₂O₃ carbide catalysts showed enhanced HDN activity compared to the NiMo/γ-Al₂O₃ catalysts with both the feed stocks. The P had almost no influence on the HDS activity of NiMo/γ-Al₂O₃ carbide with LGO and dibenzothiophene. P addition to NiMo/γ-Al₂O₃ carbide accelerated CN bond breaking and thus increased the HDN activity.     

Influence of CO2 and H2O on NOx storage and reduction on a Pt–Ba/γ-Al2O3 catalyst

In this paper, the effect of CO₂ and H₂O on NO_x storage and reduction over a Pt–Ba/γ-Al₂O₃ (1 wt.% Pt and 30 wt.% Ba) catalyst is shown. The experimental results reveal that in the presence of CO₂ and H₂O, NO_x is stored on BaCO₃ sites only. Moreover, H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. Only 16% of the total barium is utilized in NO storage. The rich phase shows 95% selectivity towards N₂ as well as complete regeneration of stored NO. In the presence of CO₂, NO is oxidized into NO₂ and more NO_x is stored as in the presence of H₂O, resulting in 30% barium utilization. Bulk barium sites are inactive in NO_x trapping in the presence of CO₂·NH₃ formation is seen in the rich phase and the selectivity towards N₂ is 83%. Ba(NO₃)₂ is always completely regenerated during the subsequent rich phase. In the absence of CO₂ and H₂O, both surface and bulk barium sites are active in NO_x storage. As lean/rich cycling proceeds, the selectivity towards N₂ in the rich phase decreases from 82% to 47% and the N balance for successive lean/rich cycles shows incomplete regeneration of the catalyst. This incomplete regeneration along with a 40% decrease in the Pt dispersion and BET surface area, explains the observed decrease in NO_x storage.     

Synthesis of bulk and alumina-supported γ-Mo2N catalysts by a single-step complex decomposition method

A single-step complex decomposition method for the synthesis of bulk and alumina-supported γ-Mo₂N catalysts is described. The complex precursor (HMT)₂(NH₄)₄Mo₇O₂₄·2H₂O (HMT: hexamethylenetetramine) is converted to γ-Mo₂N under a flow of Ar in a temperature range of 823–1023 K. Furthermore, decomposition of the precursor in a NH₃ flow forms γ-Mo₂N in a temperature range of 723–923 K. Compared with direct decomposition of the precursor in Ar, the reaction in NH₃ shows obvious advantages that the nitride forms at a lower temperature. In addition, alumina-supported γ-Mo₂N catalysts with different nitride loadings can be prepared from the alumina-supported complex precursor in the Ar or NH₃ flow. The resultant catalysts exhibit good dibenzothiophene HDS activities, which are similar to the γ-Mo₂N/γ-Al₂O₃ prepared by traditional TPR method. The catalyst prepared by decomposition in an Ar flow exhibits highest activity. It proves that such a single-step complex decomposition method possesses the potential to be a general route for the preparation of molybdenum nitride catalysts.     

M/γ-Al2O3催化剂对煤油水重整制氢的影响

以γ-Al₂O₃为载体,采用等体积分步浸渍法制备了以Ni为活性组分,La、Ce、Fe、Cr、Co为助剂的催化剂M/γ-Al₂O₃,在固定床管式反应器中研究了M/γ-Al₂O₃催化剂的性能,考察了反应温度、水碳比和空速对氢产率的影响,并对催化剂进行XRD、SEM和BET表征。结果表明,NiLaCeFeCrCo/γ-Al₂O₃催化剂具有较好的催化性能,在反应温度700 ℃、水碳物质的量比10和空速6 min^-1的条件下,氢产率达到27.335 mol·mol^-1,并在300 min内表现出较好的活性,平均氢产率为21.966 mol·mol^-1。     

Catalytic reduction of SO2 over supported transition-metal oxide catalysts with C2H4 as a reducing agent

This work investigates performances of supported transition-metal oxide catalysts for the catalytic reduction of SO₂ with C₂H₄ as a reducing agent. Experimental results indicate that the active species, the support, the feed ratio of C₂H₄/SO₂, and pretreatment are all important factors affecting catalyst activity. Fe₂O₃/γ-Al₂O₃ was found to be the most active catalyst among six γ-Al₂O₃-supported metal oxide catalysts tested. With Fe₂O₃ as the active species, of the supports tested, CeO₂ is the most suitable one. Using this Fe₂O₃/CeO₂ catalyst, we found that the optimal Fe content is 10 wt.%, the optimal feed ratio of C₂H₄/SO₂ is 1:1, and the catalyst presulfidized by H₂+H₂S exhibits a higher performance than those pretreated with H₂ or He. Although the feed concentrations of C₂H₄:SO₂ being 3000:3000 ppm provide a higher conversion of SO₂, the sulfur yield decreases drastically at temperatures above 300 °C. With higher feed concentrations, maximum yield appears at higher temperatures. The C₂H₄ temperature-programmed desorption (C₂H₄-TPD) and SO₂-TPD desorption patterns illustrate that Fe₂O₃/CeO₂ can adsorb and desorb C₂H₄ and SO₂ more easily than can Fe₂O₃/γ-Al₂O₃. Moreover, the SO₂-TPD patterns further show that Fe₂O₃/γ-Al₂O₃ is more seriously inhibited by SO₂. These findings may properly explain why Fe₂O₃/CeO₂ has a higher activity for the reduction of SO₂.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

Study of Ag/La0.6Sr0.4MnO3 catalysts for complete oxidation of methanol and ethanol at low concentrations

Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure were prepared by using a citric acid sol–gel method, and their catalytic performance for complete oxidation of methanol and ethanol was evaluated and compared with that of the γ-Al₂O₃-supported catalysts, Ag/γ-Al₂O₃, Pt/γ-Al₂O₃, and Pd/γ-Al₂O₃. The results showed that the Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure displayed the activity significantly higher than that of the supported precious metal catalysts, 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ in the temperature range of 370–573 K. Over a 6%Ag/20%La_0.6Sr_0.4MnO₃/γ-Al₂O₃ catalyst, the T₉₅ temperature for methanol oxidation can be as low as 413 K. Even at such low reaction temperature, there were little HCHO and CO detected in the reaction exit-gas. However, for the 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ catalysts, the HCHO content in the reaction exit-gas reached 200 and 630 ppm at their T₉₅ temperatures. Over a 6%Ag/La_0.6Sr_0.4MnO₃ catalyst, the T₉₅ temperature for ethanol oxidation can be as low as 453 K, with a corresponding content of CH₃CHO in the exit-gas at 782 ppm; when ethanol oxidation is performed at 493 K, the content of acetaldehyde in the exit-gas can be below 1 ppm. Characterization of the catalysts by X-ray diffraction (XRD), TEM, XPS, laser Raman spectra (LRS), hydrogen temperature-programmed reduction (H₂-TPR) and oxygen temperature-programmed desorption (O₂-TPD) methods revealed that both the surface and the bulk phase of the perovskite La_0.6Sr_0.4MnO₃ played important roles in the catalytic oxidation of the alcohols, and that γ-Al₂O₃ as the bottom carrier could be beneficial in creating a large surface area of catalyst. Moreover, a small amount of Ag⁺ doped onto the surface of La_0.6Sr_0.4MnO₃ was able to partially occupy the positions of La³⁺ and Sr²⁺ due to their similar ionic radii, and thus, became stabilized by the perovskite lattice, which would be in favor of preventing the aggregation of the Ag species on the surface and enhancing the stability of the catalyst. On the other hand, modification of the Ag⁺ to the surface of La_0.6Sr_0.4MnO₃ resulted in an increase in relative content of the surface O₂²⁻/O⁻ species highly reactive toward the alcohols and aldehydes as well as CO. Besides, solution of low-valence metal oxides SrO and Ag₂O with proper amounts in the lattice of the trivalent metal perovskite-type oxide LaMnO₃ would also lead to an increase in the content of the reducible Mnⁿ⁺ and the formation of anionic vacancies, which would be favorable for the adsorption-activation of oxygen on the functioning catalyst and the transport of the lattice and surface oxygen species. All these factors would contribute to the pronounced improvement of the catalyst performance.     

Inhibition effect of H2O on V2O5/AC catalyst for catalytic reduction of NO with NH3 at low temperature

The inhibition effect of H₂O on V₂O₅/AC catalyst for NO reduction with NH₃ is studied at temperatures up to 250 °C through TPD, elemental analyses, temperature-programmed surface reaction (TPSR) and FT-IR analyses. The results show that H₂O does not reduce NO and NH₃ adsorption on V₂O₅/AC catalyst surface, but promotes NH₃ adsorption due to increases in Brønsted acid sites. Many kinds of NH₃ forms present on the catalyst surface, but only NH₄⁺ on Brønsted acid sites and a small portion of NH₃ on Lewis acid sites are reactive with NO at 250 °C or below, and most of the NH₃ on Lewis acid sites does not react with NO, regardless the presence of H₂O in the feed gas. H₂O inhibits the SCR reaction between the NH₃ on the Lewis acid sites and NO, and the inhibition effect increases with increasing H₂O content. The inhibition effect is reversible and H₂O does not poison the V₂O₅/AC catalyst.     

The effect of hydrogen on the selective catalytic reduction of NO in excess oxygen over Ag/Al2O3

The selective catalytic reduction (SCR) of nitrogen oxides (NO_x) by propane in the presence of H₂ on sol–gel prepared Ag/Al₂O₃ catalysts (0.5–5 wt.% Ag) was investigated. It was confirmed that hydrocarbon-assisted SCR of NO_x is remarkably enhanced by co-feeding hydrogen to a lean exhaust gas mixture (λ>1), attaining considerable activity within a wide temperature window (470–825 K). The samples had marginal activity at 575 K without co-fed H₂, but achieved up to 60% NO_x conversion in the presence of H₂ at a space velocity of 30,000 h⁻¹. NO₂ as NO_x feed component is not converted to N₂ by C₃H₈ to a substantial extent under lean conditions. This points to an activation route of NO through direct conversion to adsorbed nitrite/nitrate or to a dissociation of NO over Ag⁰, formed through short-term reduction by H₂. The nature of Ag species was characterized by X-ray diffraction, temperature-programmed reduction, pulse thermoanalytical measurements, electron microscopy and FTIR spectroscopy. It could be shown that Ag₂O nano-sized clusters are predominantly present on all samples, whereas formation of silver aluminate could not be confirmed. Nano-sized Ag₂O clusters can reversibly be reduced/reoxidized by H₂. A silver loading higher than 2 wt.% leads to a part of Ag₂O particles, which are thermally decomposed during calcination at 800 K or higher. The catalytic role of this metallic silver is still unclear. Formal kinetic analysis of catalytic data revealed that the activation energy of the overall reaction is significantly lowered in the presence of H₂. The presence of water does not change the activation energy. It is concluded that hydrogen reduces the nano-sized Ag₂O clusters to Ag⁰ on a short-term scale. Zero-valent silver promotes a dissociation pathway of NO_x conversion. The fact that more oxidized ad-species (nitrite/nitrate) are observed in the presence of H₂ is attributed to a dissociative activation of gas-phase oxygen on Ag⁰.     

Mixed reforming of heptane to syngas in the Ba0.5Sr0.5Co0.8Fe0.2O3 membrane reactor

Fuel cells are recognized as the most promising new power generation technology, but hydrogen supply is still a problem. In our previous work, we have developed a LiLaNiO/γ-Al₂O₃ catalyst, which is excellent not only for partial oxidation of hydrocarbons, but also for steam reforming and autothermal reforming. However, the reaction needs pure oxygen or air as oxidant. We have developed a dense oxygen permeable membrane Ba_0.5Sr_0.5Co_0.8Fe_0.2O₃ which has an oxygen permeation flux around 11.5 ml/cm² min at reaction conditions. Therefore, this work is to combine the oxygen permeable membrane with the catalyst LiLaNiO/γ-Al₂O₃ in a membrane reactor for hydrogen production by mixed reforming of heptane. Under optimized reaction conditions, a heptane conversion of 100%, a CO selectivity of 91–93% and a H₂ selectivity of 95–97% have been achieved.