共查询到18条相似文献,搜索用时 171 毫秒
1.
2.
单相两级有源功率因数校正变换器的研究 总被引:1,自引:0,他引:1
文中对两级有源功率因数校正变换器进行研究,设计了一台510W两级式开关电源。该电源前级采用平均电流控制的Boost型PFC电路,实现功率因数校正;后级采用不对称半桥型DC/DC变换器,实现开关管的零电压开关。控制电路采用PFC/PWM复合控制芯片ML4824,缩小电源体积。通过实验证实该开关电源具有高功率因数与高效率的特点。 相似文献
3.
4.
本文收集了单相电源供电的民用变频设备无源功率因数校正(PFC)的多种可选设计电路,重点描述了一种谐振电抗器PFC设计方案,给出了部分实验数据。 相似文献
5.
传统的开关电源均存在功率因数低的问题,改善开关电源的功率因数始终是学术界的热点。文章阐述了单级功率因数校正电路的发展历史,比较了两级PFC与单级PFC电路的结构,列举了几种常用的单级功率因数校正电路,并对单级隔离式PFC变换器的控制方案做了简单探讨。 相似文献
6.
简要介绍开关电源的工作模型和工作原理,对各工作单元的设计都有较详细的论述,如功率因数校正,移相谐振(准谐振)技术,无主次均流技术等的设计要点。 相似文献
7.
两级功率因数校正(PFC)变换器因其较高的功率因数而广泛应用于功率因数校正场合。近年来,随着PFC/PWM复合控制芯片的应用,两级功率因数校正技术得到了很大的发展。传统两级PFC采用后缘/后缘调制方法(Trailing Edge Modulation/Trailing Edge Modulation,TEM/TEM)。而现今广泛使用前缘/后缘调制方法(Leading Edge Modulation/Trailing Edge Modulation,LEM/TEM)可有效减小流经连接前级PFC和后级DC/DC阶段的直直连接电容的电流有效值,但尚未有详细的理论推导。文章在两种调制方法下对流经直直连接电容的电流有效值进行了详细的理论分析,并给出了仿真验证。最后,利用复合控制芯片ML4803设计了一台具有功率因数校正功能的两级PFC变换器,对理论仿真分析进行了实验验证。 相似文献
8.
9.
近十几年中,基于功率因数校正(PFC)控制IC的有源PFC技术在开关电源、变频调速器和荧火灯交流电子镇流器等领域中得到广泛应用。这类有源PFC都能在桥式整流器输入端产生与AC输入电压同相位的正弦波电流,系统功率因数接近于1。 相似文献
10.
11.
12.
13.
Yu-Lung Ke Ying-Chun Chuang 《Circuits and Systems II: Express Briefs, IEEE Transactions on》2006,53(2):115-119
This paper presents a novel method of power-factor correction (PFC) using a high-frequency resonant energy tank for the dc-link inverter. The proposed approach has advantages over conventional PFC techniques in terms of a lower current stress and lower switching losses. The developed PFC circuit is implemented on a series-load resonant inverter for illustrative purposes. The experimental results validate the theoretical analyses. The PFC circuit can achieve a power factor of almost one with a very low harmonic distortion. 相似文献
14.
高功率因数开关电源的研究 总被引:2,自引:0,他引:2
普通开关电源采用电容输入型二级管整流电路,使输入电流呈脉冲波形,造成功率因数很低。如何提高开关电源的功率因数已经成为电源设计工程师的首要任务。文章给出了高功率因数高频开关电源系统的总体设计方案,并在此基础上,对各电路的工作过程进行了简单介绍。 相似文献
15.
16.
介绍了电流脉宽型调制芯片UC3846及其应用特点。设计了基于UC3846在变频控制上的一个电路,对此电路进行具体分析,并将此运用于LLC谐振电源控制。目前已成功应用于谐振电源样机中,运行稳定,该电路设计对调宽型芯片运用于调频有一定的借鉴意义。 相似文献
17.
《Industrial Electronics, IEEE Transactions on》2008,55(9):3180-3191
18.
Azcondo F.J. Branas C. Casanueva R. Bracho S. 《Industrial Electronics, IEEE Transactions on》2005,52(1):56-65
Medium- to high-power electronic ballasts are designed with two power conversion stages. The power-factor corrector (PFC) stabilizes the voltage supplied to the second stage and forces the utility current to meet the required standard. The inverter section stabilizes the arc in the lamp, and keeps the lamp power under the specified values. This paper proposes that the PFC section is to provide the power stability of the system while the inverter section operates in open loop. Consequences of this solution are: the power variation in the lamp caused by its aging is prevented, the complex dynamic of the lamp has no influence in the design, some extra voltage is available to achieve the lamp ignition, warmup time is reduced, and dimming control is easily implemented by modifying either the power reference or the bias value in the PFC control circuit. The inverter section is a half-bridge LC/sub p/C/sub s/ resonant inverter designed to require minimum variation of the input voltage to supply constant power to the lamp. In this way the operation point suffers little changes and no overdimensioning of the PFC and inverter components is necessary to meet the power source condition. 相似文献