A study on the in vitro degradation of poly(L-lactide)/chitosan microspheres scaffolds

Recent research shows that the addition of chitosan microspheres (CMs) to poly(L-lactide) (PLLA) can result in a composite scaffold material with improved biocompatibility and mechanical properties for tissue engineering applications. However, research regarding the influence of CMs on scaffold degradation is absent in the literature. This paper presents a study on the in vitro degradation of scaffolds made from PLLA with CMs. In this study, the PLLA/CMs scaffolds with a 25% ratio of CMs to PLLA were immersed in phosphate-buffered saline (PBS) solution at 37°C for 8 weeks. The in vitro degradation of the scaffolds was investigated using micro-computed tomography (μCT), weight loss analysis, Raman spectroscopy, and differential scanning calorimetry (DSC). Microstructure changes during degradation were monitored using μCT. The μCT results were consistent with the results obtained from Raman spectra and DSC analysis, which reflected that adding CMs into PLLA can decrease the degradation rate compared with pure PLLA scaffolds. The results suggest that PLLA/CMs scaffold degradation can be regulated and controlled to meet requirements imposed a given tissue engineering application.     

Transfer of collagen coating from porogen to scaffold: Collagen coating within poly(dl-lactic-co-glycolic acid) scaffold

Using paraffin micro-spheres as porogen, this paper addressed a novel method to coat collagen onto the internal pore surface within poly(dl-lactic-co-glycolic acid) (PLGA) scaffold with controlled pore size. The paraffin micro-spheres with desirable size were mixed with collagen solution (0.5–1.0% w/v), molded to form a paraffin micro-sphere scaffold, and dried. The collagen was left on the surface of the paraffin micro-spheres and even among the paraffin micro-spheres. PLGA solution was then cast into the interspace of the paraffin/collagen scaffold and dried. After the paraffin micro-spheres were dissolved and removed, PLGA scaffold with controlled pore size, good interconnectivity and high porosity was obtained. Collagen was transferred from the paraffin micro-spheres to the surfaces of the pore wall. Observation of scanning electron microscopy (SEM) showed that collagen was coated on the paraffin micro-spheres and was on the surfaces of pore wall within PLGA scaffold. Fourier transform infrared spectroscopy (FTIR) also detected the presence of collagen in the PLGA scaffold so formed; and there was no apparent change on the molecular components of collagen during the experimental procedure.     

Needle-like nano hydroxyapatite/poly(l-lactide acid) composite scaffold for bone tissue engineering application

In this paper, a new nano-hydroxyapatite / poly (l-lactide acid) (nHAP/PLLA) composite scaffold comprising needle-like nHAP particles was prepared. In the first step, the identification and morphology of chemically synthesized HAP particles were determined by XRD, EDX, FTIR and SEM analyses. The needle-like nHAP particles with an average size of approximately 30–60 nm in width and 100–400 nm in length were found similar to needle-like bone nano apatites in terms of chemical composition and morphology. In the second step, nHAP and micro-sized HAP (mHAP) particles were used to fabricate HAP filled PLLA (HAP/PLLA) composites scaffolds using solid–liquid phase separation method. The porosity of scaffolds was up to 85%, and their average macropore diameter was in the range of 64–175 µm. FTIR and XRD analyses showed the presence of molecular interactions and chemical linkages between HAP particles and PLLA matrix. The compressive strength of nanocomposite scaffolds could high up to 8.46 MPa while those of pure PLLA and microcomposite scaffolds were 1.79 and 4.61 MPa, respectively. The cell affinity and cytocompatibility of the nanocomposite scaffold were found to be higher than those of pure PLLA and microcomposite scaffolds. Based on the results, the newly developed nHAP/PLLA composite scaffold is comparable with cancellous bone in terms of microstructure and mechanical strength, so it may be a suitable alternative for bone tissue engineering applications.     

软骨细胞在聚乳酸支架中的体外生长行为

采用明胶和氯化钠颗粒作为致孔剂,使用溶剂浇铸／颗粒沥滤法制备了高孔隙率、孔间连通和高机械性能的聚乳酸支架,采用软骨细胞体外培养研究了这两种多孔支架对细胞生长性能的影响．结果表明,软骨细胞在以明胶颗粒为致孔剂制备的多孔支架中的相对数量和GAG的分泌量更多,细胞的活性更高。     

In Vitro Characterizations of PLLA/β-TCP Porous Matrix Materials and RMSC-PLLA-β-TCP Composite Scaffolds

To develop a novel degradable poly (L-lactic acid)/β-tricalcium phosphate (PLLA/β-TCP) bioactive materials for bone tissueengineering, β-TCP powder was produced by a new wet process. Porous scaffolds were prepared by three steps, i.e. solventcasting, compression molding and leaching stage. Factors influencing the compressive strength and the degradation behaviorof the porous scaffold, e.g. weight fraction of pore forming agent-sodium chloride (NaCl), weight ratio of PLLA: β-TCP,the particle size of β-TCP and the porosity, were discussed in details. Rat marrow stromal cells (RMSC) were incorporatedinto the composite by tissue engineering approach. Biological and osteogenesis potential of the composite scaffold weredetermined with MTT assay, alkaline phosphatase (ALP) activity and bone osteocalcin (OCN) content evaluation. Resultsshow that PLLA/β-TCP bioactive porous scaffold has good mechanical and pore structure with adjustable compressive strengthneeded for surgery. RMSCs seeding on porous PLLA/     

Formation of bone-like apatite on poly(L-lactide) to improve osteoblast-like compatibility in vitro and in vivo

The biomimetic apatite coating process was adopted to modify poly(L-lactide) (PLLA) surfaces with osteoblasts-like cell compatibility. The apatite coating was formed on the pre-hydrolyzed PLLA film and scaffold surfaces by incubating in simulated body fluid (SBF). Scanning electron microscopy and energy dispersive X-ray analyzer were utilized to characterize the composition and the structure of the apatite coating. The cytocompatibility of the modified PLLA films was investigated by testing osteoblast-like attachment, proliferation, alkaline phosphatase (ALP) activity, and cell cycle. Subsequently, the modified PLLA scaffolds were co-cultured with the osteoblasts-like in vitro and subcutaneously implanted into nude mice. The experimental results showed that the formed apatite had a nano-sized particle and matrix configuration. The surface modification of PLLA with apatite coating significantly promoted osteoblast-like compatibility. After a four-week culture in vivo, no significant inflammatory signs were observed in the implanted regions and osteoblast-like congeries with bone-like structure began to form in the scaffolds. The positive results of this study suggest a good way to produce desirable PLLA biomaterials for bone tissue engineering.     

Fabrication of bioactive composite by developing PLLA onto the framework of sintered HA scaffold

Composite porous scaffolds of hydroxyapatite (HA)/poly-l-lactide (PLLA) were fabricated by a two-step immersing replication method. Structure and mechanical properties of both the single HA scaffold and the composite HA/PLLA scaffold were determined. The bioactivity of the scaffolds was evaluated by soaking in a simulated body fluid (SBF), and the formation of the apatite layer was determined by X-ray diffraction (XRD), Scanning Electron Microscope (SEM) and Energy-Dispersive Spectrometer (EDS). The results showed that without changing the highly interconnected porous structure, the HA/PLLA composite scaffold was mechanically enhanced to a great deal of extent compared with single HA scaffold. On the other hand, it is also suggested that the HA/PLLA scaffold was bioactive as it induced the formation of apatite on the surface of the composite scaffolds after soaking in SBF for 7 days.     

PLLA–collagen and PLLA–gelatin hybrid scaffolds with funnel-like porous structure for skin tissue engineering

Abstract

In skin tissue engineering, a three-dimensional porous scaffold is necessary to support cell adhesion and proliferation and to guide cells moving into the repair area in the wound healing process. Structurally, the porous scaffold should have an open and interconnected porous architecture to facilitate homogenous cell distribution. Moreover, the scaffolds should be mechanically strong to protect deformation during the formation of new skin. In this study, the hybrid scaffolds were prepared by forming funnel-like collagen or gelatin sponge on a woven poly(l-lactic acid) (PLLA) mesh. The hybrid scaffolds combined the advantages of both collagen or gelatin (good cell-interactions) and PLLA mesh (high mechanical strength). The hybrid scaffolds were used to culture dermal fibroblasts for dermal tissue engineering. The funnel-like porous structure promoted homogeneous cell distribution and extracellular matrix production. The PLLA mesh reinforced the scaffold to avoid deformation. Subcutaneous implantation showed that the PLLA–collagen and PLLA–gelatin scaffolds promoted the regeneration of dermal tissue and epidermis and reduced contraction during the formation of new tissue. These results indicate that funnel-like hybrid scaffolds can be used for skin tissue regeneration.     

PLLA–collagen and PLLA–gelatin hybrid scaffolds with funnel-like porous structure for skin tissue engineering

In skin tissue engineering, a three-dimensional porous scaffold is necessary to support cell adhesion and proliferation and to guide cells moving into the repair area in the wound healing process. Structurally, the porous scaffold should have an open and interconnected porous architecture to facilitate homogenous cell distribution. Moreover, the scaffolds should be mechanically strong to protect deformation during the formation of new skin. In this study, the hybrid scaffolds were prepared by forming funnel-like collagen or gelatin sponge on a woven poly(l-lactic acid) (PLLA) mesh. The hybrid scaffolds combined the advantages of both collagen or gelatin (good cell-interactions) and PLLA mesh (high mechanical strength). The hybrid scaffolds were used to culture dermal fibroblasts for dermal tissue engineering. The funnel-like porous structure promoted homogeneous cell distribution and extracellular matrix production. The PLLA mesh reinforced the scaffold to avoid deformation. Subcutaneous implantation showed that the PLLA–collagen and PLLA–gelatin scaffolds promoted the regeneration of dermal tissue and epidermis and reduced contraction during the formation of new tissue. These results indicate that funnel-like hybrid scaffolds can be used for skin tissue regeneration.     

Preparation and comparative characterization of keratin–chitosan and keratin–gelatin composite scaffolds for tissue engineering applications

We report fabrication of three dimensional scaffolds with well interconnected matrix of high porosity using keratin, chitosan and gelatin for tissue engineering and other biomedical applications. Scaffolds were fabricated using porous Keratin–Gelatin (KG), Keratin–Chitosan (KC) composites. The morphology of both KG and KC was investigated using SEM. The scaffolds showed high porosity with interconnected pores in the range of 20–100 μm. They were further tested by FTIR, DSC, CD, tensile strength measurement, water uptake and swelling behavior. In vitro cell adhesion and cell proliferation tests were carried out to study the biocompatibility behavior and their application as an artificial skin substitute. Both KG and KC composite scaffolds showed similar properties and patterns for cell proliferation. Due to rapid degradation of gelatin in KG, we found that it has limited application as compared to KC scaffold. We conclude that KC scaffold owing to its slow degradation and antibacterial properties would be a better substrate for tissue engineering and other biomedical application.     

介孔纳米羟基磷灰石/左旋聚乳酸复合材料的制备及性能

为考察介孔纳米羟基磷灰石(MHA)/左旋聚乳酸(PLLA)复合材料的性能,以十六烷基三甲基溴化铵(CTAB)为模板合成MHA,采用溶液相分离结合粒子沥滤法制备了不同纳米粒子含量的MHA/PLLA多孔支架复合材料,考察了其抗压缩性能和淬断面微观结构。采用溶液浇注法制备了MHA/PLLA复合膜,并对其拉伸性能和拉伸断面微观结构进行了研究。FTIR、XRD、TEM和氮气吸附测试等结果显示:合成的MHA具有典型的晶体结构、介孔结构和较高的比表面积。力学测试结果显示:在发生10%压缩形变时,填料含量为1%、5%和10%的MHA/PLLA多孔支架复合材料的抗压缩强度随填料含量增加而提高,与相应含量的纳米羟基磷灰石(HA)/PLLA多孔支架复合材料相比,分别提高了约37.0%、67.7%和144.7%。在填料含量为5%和10%时,MHA/PLLA复合膜的拉伸强度较HA/PLLA复合膜分别提高约38.7%和46.1%,拉伸模量分别提高约35.4%和14.5%。而且MHA/PLLA复合膜具有更高的断裂伸长率,填料含量为1%、5%和10%时断裂伸长率分别较HA/PLLA复合膜提高约91.3%、79.7%和96.1%。FESEM结果显示:尤其当填料含量较高时,MHA/PLLA多孔支架复合材料或复合膜中填料粒子分布较HA/PLLA中均匀。结果表明:与HA/PLLA复合材料相比,随着MHA含量增加,MHA/PLLA复合材料具有更好的力学性能,MHA在PLLA基体中分布相对更均匀。     

Coating of collagen on a poly(l-lactic acid) sponge surface for tissue engineering

Porous scaffolds play important roles in tissue engineering. Biodegradable synthetic polymers, such as poly(l-lactic acid) (PLLA), frequently are used in the preparation of porous scaffolds. Pretreating the surface of a PLLA porous scaffold is required to increase its wettability for smooth cell seeding due to the hydrophobic property of the scaffold's surface. In this study, a simple coating method was used to modify the surface of the PLLA sponges. The coating method included three steps: filling the PLLA sponge pores with collagen aqueous solution, centrifuging to remove excess collagen, and, finally, freeze-drying. Compared with the uncoated PLLA sponge, the collagen-coated PLLA sponge demonstrated both improved wettability and high water absorption. Cells were smoothly seeded in the collagen-coated PLLA sponges by dropping a cell suspension solution onto the sponges. Cells adhered to the collagen-coated sponge and were distributed homogeneously throughout the collagen-coated PLLA sponge.     

Poly(L-lactic acid) nanocylinders as nanofibrous structures for macroporous gelatin scaffolds

Electrospun Nanofiber sheets have been shown to mimic the structure of extracellular matrix (ECM). Although these nanofibers have shown great potential for use as tissue engineering scaffolds, it is difficult for the electrospun nanofiber based sheets to be shaped into the desired three-dimensional structure. In this study, poly(L-lactic acid) (PLLA), a biodegradable and biocompatible polyester, was electrospun to produce nanofibers that were treated with an amino group containing base in order to fabricate polymeric nanocylinders. The aspect ratio of the PLLA nanocylinders was tunable by varying the aminolysis time and density of the amino group containing base. The effects of changes in nanofibrous morphology of the PLLA nanocylinders/macro-porous gelatin scaffolds on cell adhesion and proliferation were evaluated. The results revealed different cell morphology, adhesion, and proliferation in the nanocylinders composite gelatin scaffold versus gelatin scaffold alone. Confocal laser scanning microscopy observation showed more spreading and a more flattened cell morphology after NIH3T3 cells were cultured on PLLA nanocylinders/gelatin scaffolds for 10 hours and 4 days. These results indicate that the gelatin/PLLA nanocylinder composite is a promising way to fabricate 3D nanofibrous scaffolds that accelerates cell adhesion and proliferation for tissue engineering.     

3D polylactide-based scaffolds for studying human hepatocarcinoma processes in vitro

We evaluated the combination of leaching techniques and melt blending of polymers and particles for the preparation of highly interconnected three-dimensional polymeric porous scaffolds for in vitro studies of human hepatocarcinoma processes. More specifically, sodium chloride and poly(ethylene glycol) (PEG) were used as water-soluble porogens to form porous and solvent-free poly(L,D-lactide) (PLA)-based scaffolds. Several characterization techniques, including porosimetry, image analysis and thermogravimetry, were combined to improve the reliability of measurements and mapping of the size, distribution and microarchitecture of pores. We also investigated the effect of processing, in PLA-based blends, on the simultaneous bulk/surface modifications and pore architectures in the scaffolds, and assessed the effects on human hepatocarcinoma viability and cell adhesion. The influence of PEG molecular weight on the scaffold morphology and cell viability and adhesion were also investigated. Morphological studies indicated that it was possible to obtain scaffolds with well-interconnected pores of assorted sizes. The analysis confirmed that SK-Hep1 cells adhered well to the polymeric support and emitted surface protrusions necessary to grow and differentiate three-dimensional systems. PEGs with higher molecular weight showed the best results in terms of cell adhesion and viability.     

3D polylactide-based scaffolds for studying human hepatocarcinoma processes in vitro

Abstract

We evaluated the combination of leaching techniques and melt blending of polymers and particles for the preparation of highly interconnected three-dimensional polymeric porous scaffolds for in vitro studies of human hepatocarcinoma processes. More specifically, sodium chloride and poly(ethylene glycol) (PEG) were used as water-soluble porogens to form porous and solvent-free poly(L,D-lactide) (PLA)-based scaffolds. Several characterization techniques, including porosimetry, image analysis and thermogravimetry, were combined to improve the reliability of measurements and mapping of the size, distribution and microarchitecture of pores. We also investigated the effect of processing, in PLA-based blends, on the simultaneous bulk/surface modifications and pore architectures in the scaffolds, and assessed the effects on human hepatocarcinoma viability and cell adhesion. The influence of PEG molecular weight on the scaffold morphology and cell viability and adhesion were also investigated. Morphological studies indicated that it was possible to obtain scaffolds with well-interconnected pores of assorted sizes. The analysis confirmed that SK-Hep1 cells adhered well to the polymeric support and emitted surface protrusions necessary to grow and differentiate three-dimensional systems. PEGs with higher molecular weight showed the best results in terms of cell adhesion and viability.     

分级多孔壳聚糖/聚乳酸复合支架的制备及骨修复性能

为了仿生莲藕内部的贯穿大孔结构,以生物相容性好的壳聚糖(CS)作为基质材料,利用冰粒致孔、石蜡模具和冰模具成型3种成型方法制备了分级多孔CS支架材料,然后与力学强度较高的聚乳酸(PLLA)复合,制备网络互穿CS/PLLA复合支架。通过SEM、压缩强度测试和兔股骨髁骨缺损模型对CS/PLLA复合材料的形貌、力学强度和骨修复性能进行了表征。结果表明:利用冰模具制备的CS/PLLA复合支架能可控、批量制备,具有微米-毫米分级多孔结构,大孔孔径约为2mm,内部均匀分布着孔径约为60μm的贯穿微孔,并在微孔内形成密集的PLLA絮状网络结构。干态复合材料的压缩强度和模量分别比纯CS支架的提高了6倍和15倍。体内植入实验结果表明,CS/PLLA复合材料能够促进骨缺损的愈合,并随着新骨的形成,复合材料逐渐被降解吸收。     

Polyurethane (PU) scaffolds prepared by solvent casting/particulate leaching (SCPL) combined with centrifugation

This article reports an enhanced solvent casting/particulate (salt) leaching (SCPL) method developed for preparing three-dimensional porous polyurethane (PU) scaffolds for cardiac tissue engineering. The solvent for the preparation of the PU scaffolds was a mixture of dimethylformamide (DFM) and tetrahydrofuran (THF). The enhanced method involved the combination of a conventional SCPL method and a step of centrifugation, with the centrifugation being employed to improve the pore uniformity and the pore interconnectivity of scaffolds. Highly porous three-dimensional scaffolds with a well interconnected porous structure could be achieved at the polymer solution concentration of up to 20% by air or vacuum drying to remove the solvent. When the salt particle sizes of 212–295, 295–425, or 425–531 µm and a 15% w/v polymer solution concentration were used, the porosity of the scaffolds was between 83–92% and the compression moduli of the scaffolds were between 13 kPa and 28 kPa. Type I collagen acidic solution was introduced into the pores of a PU scaffold to coat the collagen onto the pore walls throughout the whole PU scaffold. The human aortic endothelial cells (HAECs) cultured in the collagen-coated PU scaffold for 2 weeks were observed by scanning electron microscopy (SEM). It was shown that the enhanced SCPL method and the collagen coating resulted in a spatially uniform distribution of cells throughout the collagen-coated PU scaffold.     

Chitosan-collagen/organomontmorillonite scaffold for bone tissue engineering

A novel composite scaffold based on chitosan-collagen/organomontmo-rillonite (CS-COL/OMMT) was prepared to improve swelling ratio, biodegradation ratio, biomineralization and mechanical properties for use in tissue engineering applications. In order to expend the basal spacing, montmorillonite (MMT) was modified with sodium dodecyl sulfate (SDS) and was characterized by XRD, TGA and FTIR. The results indicated that the anionic surfactants entered into interlayer of MMT and the basal spacing of MMT was expanded to 3.85 nm. The prepared composite scaffolds were characterized by FTIR, XRD and SEM. The swelling ratio, biodegradation ratio and mechanical properties of composite scaffolds were also studied. The results demonstrated that the scaffold decreased swelling ratio, degradation ratio and improved mechanical and biomineralization properties because of OMMT.     

Composite poly-l-lactic acid/poly-(α,β)-dl-aspartic acid/collagen nanofibrous scaffolds for dermal tissue regeneration

Tissue engineering scaffolds for skin tissue regeneration is an ever expounding area of research, as the products that meet the necessary requirements are far and elite. The nanofibrous poly-l-lactic acid/poly-(α,β)-dl-aspartic acid/Collagen (PLLA/PAA/Col I&III) scaffolds were fabricated by electrospinning and characterized by SEM, contact angle and FTIR analysis for skin tissue regeneration. The cell-scaffold interactions were analyzed by cell proliferation and their morphology observed in SEM. The results showed that the cell proliferation was significantly increased (p ≤ 0.05) in PLLA/PAA/Col I&III scaffolds compared to PLLA and PLLA/PAA nanofibrous scaffolds. The abundance and accessibility of adipose derived stem cells (ADSCs) may prove to be novel cell therapeutics for dermal tissue regeneration. The differentiation of ADSCs was confirmed using collagen expression and their morphology by CMFDA dye extrusion technique. The current study focuses on the application of PLLA/PAA/Col I&III nanofibrous scaffolds for skin tissue engineering and their potential use as substrate for the culture and differentiation of ADSCs. The objective for inclusion of a novel cell binding moiety like PAA was to replace damaged extracellular matrix and to guide new cells directly into the wound bed with enhanced proliferation and overall organization. This combinatorial epitome of PLLA/PAA/Col I&III nanofibrous scaffold with stem cell therapy to induce the necessary paracrine signalling effect would favour faster regeneration of the damaged skin tissues.     

Selective laser sintering of porous tissue engineering scaffolds from poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactide)/carbonated hydroxyapatite nanocomposite microspheres

This study focuses on the use of bio-nanocomposite microspheres, consisting of carbonated hydroxyapatite (CHAp) nanospheres within a poly(L: -lactide) (PLLA) matrix, to produce tissue engineering (TE) scaffolds using a modified selective laser sintering (SLS) machine. PLLA microspheres and PLLA/CHAp nanocomposite microspheres were prepared by emulsion techniques. The resultant microspheres had a size range of 5-30 mum, suitable for the SLS process. Microstructural analyses revealed that the CHAp nanospheres were embedded throughout the PLLA microsphere, forming a nanocomposite structure. A custom-made miniature sintering platform was installed in a commercial Sinterstation((R)) 2000 SLS machine. This platform allowed the use of small quantities of biomaterials for TE scaffold production. The effects of laser power; scan spacing and part bed temperature were investigated and optimized. Finally, porous scaffolds were successfully fabricated from the PLLA microspheres and PLLA/CHAp nanocomposite microspheres. In particular, the PLLA/CHAp nanocomposite microspheres appeared to be promising for porous bone TE scaffold production using the SLS technique.